KUNRATHUR EA WORK

Amount

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering. All work upto plinth level.

1:2:4 (1 cement:4 M sand:8 graded stone aggregate 40mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:

1:5:10 (1 cement : 5 M sand : 10 graded stone aggregate 40 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form work for :

Foundations, footings, bases for columns.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 5 in foundation and plinth in:

Cement mortar 1:6 (1 cement : 6 M sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 5 in superstructure above plinth level up to floor V level in all shapes and sizes in :

Cement mortar 1:6 (1 cement : 6 M sand)

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters

80x0.90 mm M.S. laths with 0.90 mm thick top cover.

Providing and fixing ball bearing for rolling shutters.

Supplying and Filling in plinth with good earth under floors, including watering, ramming, consolidating and dressing all complete.

Structural steel work in single section, fixed with or without connecting plate,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

MS tubes.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.45 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.

40 mm thick with 20 mm nominal size stone aggregate

12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)

15 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

Two or more coats on new work.

Finishing walls with Acrylic Smooth exterior paint of required shade :

Two or more coat applied @ 1.67 ltr/ 10 sqm

Demolishing Cement concrete/R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.

In cement mortar

Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of:

Asbestos cement sheet

Dismantling Rolling Shutter ,its guide bar and cover including stacking the serviceable materials 50 metres lead

Taking out MS chequered plate including its MS angle base frame section and stacking at site all compele as directed by the E-in-C.

Taking out doors, windows and clerestory window shutters (Aluminium) including stacking within 50 metres lead:

Of area 3 sq. metres and below

Refixing of Aluminium doors/windows after servicing and fixing with new screws , neoprene rubber beading to ensure smooth functiong of window all complete

Of area 3 sq. metres and below

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete :

Credit to the unserviceable, corroded MS chequered plates , grill gate, rollong shutters all complete.