REPAIR/MAINTENANCE OF UNSERVICEABLE LT SWITCH GEAR, UG CABLES PANEL BOARDS, FEEDER PILLAR AND ALLIED WORKS AT MD ACCN, CTW, 262 CEDU, FCBRNP AT CME

Amount

Excavation in trenches n exc 1.5m wide and n exc 1.5m deep and making good surface for laying /removing of cable all as specified and directed by Engr in charge as in

(a) Soft/loose soil

(b) Hard/dense soil

(c) Soft/disintegrated rock.

Returning filling in excavated soil in trenches, watering and well ramming in layers n exc 25 cm complete all as specified.

Removal of surplus excavated spoil to distance n exc 50 metre and deposited where directed at a level n.exc. 1.5m above the starting point all as specified and directed

M & L for bituminous road cutting to a width of 45 cm and depth 50 cm for laying of pipe for laying of UG cables and making good with PCC (1:3:6) type C1 (using 20mm grade stone aggregate)

M & L erect in true vertical position (or to be fixed in an inclined position as strut pole) steel tubular swaged poles complete with MS base plate of 6 mm thick of size 300 mm x 300 mm, finial taper plug, pole cap, bolts, nuts and washers and screwed pole made out of ERW MS tubing conforming to IS-2713 (Part-II) 1980 type 410-SP-31 ( 9 meters long ) pole including drilling of holes of required size and Nos for fixing of cross arms, painting with one coat of red oxide primer and two coats of aluminium paint for exposed surfaces and two coats of black bituminous paint for portion embeded in concrete, etc complete all as specified and directed in and incl taking down carefully old deterioiated RCC/steel pole.

Supply , laying and testing cable XLPE insulated screened pvc bedded galvanised steel strip or wire armoured , electric power cables ( heavy duty) with stranded aluminium conductor 1100 volts grade in trenches/ passing through pipe/fixing on walls, floors etc incl using suitable clamp of cross sectional area 3.5 core 50 Sqmm in and including taking out old one all as specified and directed.

All as per item 06 above, but of the size 3.5 core 70 Sqmm

All as per item 06above, but of the size 3.5 core 95 Sqmm

All as per item 06 above, but of the size 3.5 core 120 Sqmm

All as per item 06 above, but of the size 3.5 core 150 Sqmm

All as per item 06 above, but of the size 3.5 core 185 Sqmm

All as per item 06 above, but of the size 3.5 core 240 Sqmm

Supply & Laying of Telerex DWC (Double Wall corrugated) HDPE pipe ISI marked of outer dia of 90 mm and inner dia 76 mm polythylene with smooth internal and profiled external surface for non pressure under ground cable incl couplers & bends complete all as specified. Make : REX POLYEXTRUSION LTD or its equivalent as approved

M&L for clean dry river sand cushioning to undeground cables in trenches including spreading, leaveling hand punning and consolidating complete all as specified. Note- thickness after punning down shall be measured and paid.

Supply and lay factory made, ISI marked, un-reinforced precast concrete cable cover class LV type-1, flat of size 250mmx150mmx40mm complete all as specified.

M&L for fault detection in damaged UG cables using cable fault detector/locator, vehicle mounted to accuracy of 2m for various locations inside CME for UG cables of any size & any type upto 22kv grade including excavation & earthwork in any type of strata of size 4x2x0.6m to visually inspect/repair the damaged cable when and where directed by Engr-in-charge.

S & fix LT Cable joining kit(straight through) heat shrinkable complete with jointing materials suitable for LT Armoured cable 3.5 core of size 10 to 50 Sqmm all as directed including taking down old one.

S & fix LT Cable joining kit(straight through) heat shrinkable complete with jointing materials suitable for LT Armoured cable 3.5 core of size 70 to 95 Sqmm all as directed including taking down old one.

S& Fix LT Cable jointing kit straight through heat shrinkable type complete with jointing materials suitable for LT Armoured cable of size 95-300 Sqmm two core all as directed including taking down old one.

Supply, stringing , stretching , fixing and strengthening on insulators ACSR conductor including aluminium binding wire of suitable cross sectional area (but not less than 16 SWG) including joints sleeve for jointing conductors of equal or unequal size and for jumpers connections including treatment of connector and ACSR conductor joints/jumpers with conducting jelly, and taking down of UNSV conductors complete all as specified and directed.

M&L for cross arms, bracing, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts, washere, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of paint including taking down old unserviceable etc complete.

Material and labour for Pin type, porcelain, vitreous, white brown or green insulator including one galvanised mild steel spindle, two galvanised iron washers and one galvanised iron nut, 100 mm height, 65 mm dia for 1100 Volts grade including taking down old one.

Material and labour for shackle type porcelain vitreous white, brown or green insulator incl GI mild steel strip, washer, insulator bolts, washers and nut for working pressure 1100 volts section of strips 31 x 3 mm,max dia 90mm, height 75 mm,dia of bolt 12mm upto 9 metre long incl taking down old unserviceable one.

S & F Stay assembly complete with accessories as shown in electrical plate No 1 incl GI Adjustable Stay Rod of 20 mm Dia, GI Stay wire of size 7/4 mm incl stay clamps, loop type insulator, excavation in any strata and PCC 1:3:6 type C2 all as specified and directed incl taking down old unserviceable stay assembly.

M&L for cradles, hexagonal/rectangular fabricated with GI steel wire 4 mm dia incl taking down old UNSV one.

M & L for PCC 1:3:6 type C1 using 20 mm graded stone aggregate for coping of poles/plinth blocks of HT poles etc incl fair finishing the exposed surfaces even and smooth without using extra cement including necessary form work complete all as specified & directed.

M & L for PCC 1:4:8 type D2 using 40mm graded stone aggregate for foundation of poles complete all as specified and as directed.

M & L for loose filling with aggegregates of gauge 40 to 80mm in switch yard

Re-stringing of over head line ACSR conductor on existing lines by unbinding at each pin/shackle/Disc type insulator and re-fixing the same after stretching conductor, removing excess sag, maintaining proper distance between conductors as specified, tightening of stay wire, S&F of PVC line seperators two per span, all as specified and as directed for the following types of configurations:-

(a) Set of four

(b) Set of three

(c) Set of two

(d) Guard wire

Cutting of Tree branches n.exc 20 cm in girth along LT OH lines at distance not less than 5 m distance from both sides of conductors complete incl clearing of bushes any type not less than dia 10 cms and all other growings around respective poles of area not less than 4 sqm all when and where as specified and as directed. Note :(Actual lengths where trimming is being done will be measured)

M&L for clearing of Grass Shrubs and other growing by uprooting in switchyards and installations upto 10 cms in girth at various locations as directed

Supplying and laying GI tubing light grade incl all accessories for encasing cables for mechanical protection , laid under Plinth / Floors/ Paths Culverts or fixed on wall or concealed in wall/floor or along poles or as street light poles or as street light mounting bracket with complete accessories such as bends/sockets/reducers/saddles incl necessary threading/drilling works including taking down old tubing . all as specified and directed of following sizes:- (MS works will be measured under seperate item in Schedule) (a) 80 mm bore

all as pe item no 32 above, but size 50 mm bore

all as pe item no 32 above, but size 40 mm bore

all as pe item no 32 above, but size 32mm bore

M&L for earthing using copper earth plate electrode of size 60cmx60cmx3.15mm thick burried directly in ground vertically a depth not less than 2.25mtr below normal ground level with top edge of earth plate depth not less than 1.5mtr below normal ground level earth plate surrounded from all sides by 15cm thick and packed layer of charcoal dust and common salt filling in alternate layers and electrode connections by using copper strip of size 20x3mm by means of bolts nuts check nuts and wahsers made of GI and protected by light grade 40mm dia galvanised iron pipe and GI pipe light grade 20mm bore for watering including funnel wire mesh CI pit cover and PCC chamber pit with PCC 1:2:4 type B2 (including necessary excavation and earth work disposal of surplus soil to a distance not exceeing 50 mtr all as specified and shown on electrical plate No 3 of SSR Part 1 2009

M&L for MCCB 3 pole, 415 V, with microprocessor release 160 amps with breaking capacity 36KA including taking down old one

M&L for MCCB 3 pole, 415 V with microprocessor release 250 amps with breaking capacity 36 KA including taking down old one

M&L for MCCB 3 pole, 415 V with microprocessor release 400 amps withbreaking capacity 36KA including taking down old one.

M & L for Preparation of old painted surfaces of electric pole covered by dust and other deposited materials by cleaning from steel tubular pole of length upto 9 metres including cross arms, bracing, clamps etc and painting with one coat of aluminium paint complete all as specified.

M & L for Preparation of old cement based painted surfaces of RCC pole 9 mtr by cleaning of deposited materials, and painting with one coat of exterior emulsion weather coat paint of approved make and colour complete all as specified.

Supply, install, connect, test and commissioning factory made, dust/vermin, weather proof self ventilated, cubicle of size 1.00 x 0.50 x 1.25/ (aps) with front made of and rear opening, hinged door for front,and rear with MS angle iron frame 50 x 50 x 5mm for base support, 3.15 mm thick CRCA sheet, LT panel board, (LT KIOSK), out door, cubicle type, floor mounted, double door with neoprene gasket and locking arrangement with canopy including painting with powder coated on steel surfaces internally & externally and provision of two Nos earth terminals on both sides , cable glands and PCC foundation with PCC 1 : 2 : 4, type B1 , to accommodate and including the following accessories:-

Aluminium bus bar rectangular 600 Amps full for phase and half for neutral and interconnection of MCCBs to Bus bar mounted on epoxy insulators with colour coding PVC sleeves.-01 job

MCCB 400 Amps, TPN, 415 Volts, 50 Hz , 35 KA - 01 No ( Incoming)

MCCB 160 Amps, TP, 415 Volts, 50 Hz , 35 KA - 05 No ( Outgoing)

Internal wiring of panel board, metering equipment with suitable size PVC insulated, unsheathed, 1100 V grade cable with multistranded copper conductor, including provision of lugs/thimbles on either ends of cable.

Provision of cubicle to accommodate the above mentioned accessories.

Indication lamp with LED lamp.

Ammeter 0 to 500 amps -01 No with CT coil

M & L for Preparation of old painted surfaces of LT Panel or Street light Panel covered by dust and other deposited materials by cleaning from Panel of Size upto 100 X 100 X 50 cm including Repair of panel door ,hinged nut .bolts clamp . etc .painting with one coat of smoke grey paint complete all as specified.

M/S kirpan Enterprises

N AND G CONSTRUCTION

UNIQUE ENGINEERS

metro electrical services

MAYUR ELECTRIC SERVICES

Pritam Electro Mechanical Services

Mahindra Electric Stores

M/S. Niksun Electro-Infra Private Limited