PROVISION OF SECURITY FENCING AROUND A VEH GARAGE OF 4 HORSE AND AROUND THE UNIT MT GARAGE AREA OF 694 COY ASC TK TPTR TYPE A AND CERTAIN REV SANCTIONED WORKS AT NASIRABAD

Amount

Surface dressing n exc 15 cm deep in soft/ loose soil complete all as specified and directed.

Surface excavation n. exc. 30cm deep and averaging 15cm deep and getting out soft/ loose soil complete all as specified and as directed

Excavation in trenches, not exc 1.5m wide and not exc 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. not exc 10 sq. m on plan and not exc 1.5m in depth and getting out in soft/loose soil complete all as specified & directed.

Excavating in post holes (or similar holes) each n.exc 0.5 cum getting out in soft/loose soil including returning, filling in and ramming earth in layers n.exc 25cm, watering and removing surplus soil to a distance n.exc 50m and making good surfaces complete all as specifed and directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers n.exc 25 cm thick complete all as specified & directed.

Removal of excavated material (soil) n.exc 50m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified & directed.

M&L for PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in foundations, filling and mass concrete including necessary formwork complete all as specified and directed.

M&L for RCC type B-1 1:2:4 nominal mix using 20mm graded crucshed stone aggregate as in foundation including rafts, footing, foundation beams, plinth beams etc including necessary form work complete all as specifie and directed.

M&L for RCC type B-1 1:2:4 nominal mix using 20mm graded crucshed stone aggregate as in coloumns, pillars, piers, posts and struts etc complete all as specifie and directed.

M & L for formwork to sides of pillars, posts, struts, piers, columns and stanchions, rectangular or polygonal surfaces of concrete, surface is required to be fair finished complete all as specified and directed.

M & L PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in coping, kerbs etc including weathering slightly, rounded or chamfered on edges including necessary form work complete all as specified and directed.

S & F framed work as in doors or gate of approved pattern, ornamental and intricate design of angle or other section with gusset plates, rail braces etc drilled for fixing of steel sheeting or other covering of doors etc to be prepared for hanging or sliding with and including either hooking and hinges or steel hanging door fitting (excluding sheeting or other covering running rails and guiders) and hanging also fastening and fixing complete all as specified & directed

M&L for MS work conforming to Fe-290 Gde-E-165 for fencing post and struts made from angle iron and flat iron in any section including cutting tops to shape, drilling holes and notching for fixing of wires etc complete all as specified and directed.

Supply only chain link MS Zink coating 60gsm as per IS 4826 fencing 50mm X 50mm mesh and 3mm dia or wire complete all as specified. NOTE: This item shall be measured and paid as per actual weight or standard weight as per SSR which ever is less. Make :- TATA (Wiron)/JINDAL

Fixing only chain link fencing including line wire, any mesh, size and any type of standards rails straining bolt etc including provision of binding wire complete all as specified and directed.

Supply only 4mm dia galvnised medium coated steel wire cut to length as required for fixing chain link fencing etc complete all as specified and directed. Make: TATA (Wiron) or Jindal

S & F Galvanised 2 strand, steel barbed wire, 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, includdigng, securing or tying at crossings with and provisiion of galavnised (Zink coating 60 gsm) mild steel wire, staples or steel pins, etc as directed each line wire to measured complete all as specified and directed. Make :- TATA (Wiron) /JINDAL

M&L 5 to 10 mm dia mild steel screw bolts (Machine made) with hexoganal or suqare head at one end and screwed the other or screwed both ends each screwed and to be bolted wih washers and one hexoganal or suqare not exc 75mm long including fixed with welding to angle complete all as specified and directed.

M & L for preparation of new steel & iron surface of width or girth exceeding 10 cm and applying two coats of synthetic enamel paint of Ist quality over a coat of red oxide primer complete all as specified and directed

M&L for preparation of new steel & iron surfaces n.exc 10 cm width or girth and apply two coats of synthetic enamel paint of 1st quality over a coat of red oxide primer complete all as specified and directed.

M & L for brick work of fly ash bricks of old size built in CM (1:6) straight or curved on plan exc 6 m mean radius complete all as specified and directed.

M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished surface fair and even complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and directed.

M & L for preparation of newly plastered surface of wall and applying two coat of cement base paint complete all as specified and directed.

M&L mild steel TMT bars in reinforcement 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends , and binding with and including binding mild steel wire(annealed) not less than 0.90mm dia or securing with clips complete all as specified and directed.

M & L for mild steel TMT bars 5mm dia and over upto including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L PCC 1:4:8 Type D-2 using 40mm graded stone aggregate as in bed of drain pipe of 150mm dia (nominal) including packing under and haunching against the size of after they are laid and tested complete all as specified and directed.

M & L for 150 mm bore salt glazed stone ware drain pipe ISI Marked laid in trenches and jointed in CM (1:1) tested complete all as specified & directed.

M & L for soakage wells including excavation in any type of soil, foundation in PCC (1:3:6), walls of honey combed fly ash brick masonry with top ring of M-25 concrete including intercepting chamber and screen chamber made of fly ash brick masonry in CM (1:6), RCC cover slab in M-25 concrete & SFRC MH cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 1.80m dia & 3.00m effective depth all as per drg No. CEBZ/TD/78/2011 sh No 1/2 & 2/2 complete all as specified and directed.

M&L septic tank for 50 users including excavation in any type of soil, foundation in PCC 1:2:4, brick work in CM 1:4, RCC slab covers including RCC precast manhole cover having 6mm plate embedded all around /fibre reinforced cover with angle iron frame vent shaft and sludge chambers etc specified in TD drg No. CEBZ/TD/76/2011 sh No 1/2 & 2/2 complete all as specified and directed.

M/s SUNIL ENTERPRISES

SHREE BALAJI TRADING CORPORATION

MADAN MOHAN JAIN sons