REPAIR TO JOINERY INTERNAL WATER SUPPLY FALSE CEILING AND MISC B R WORKS AND REPAIRS TO TEMP AND PERMT ROOF ROLLING SHUTTERS IN RESIDENTIAL AND TECH AREA AT R AND DE E DIGHI PUNE 15

Amount

Dismantling of steel roof sheeting (corrugated, semi corrugated, etc.) sheets in roof coverings, of any gauge and thickness complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M&L for Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified including corrugated ridge sheeting complete all as specified and directed.

Labour only for fixing old steel roof sheetting obtained from Item No 1.00 above but including and fixing with new self tapping screws as specified including corrugated ridge sheeting complete all as specified and directed.

S&F Rolled mild steel in plates (Plain) square cut or notched (ordinary and colour sunk) forming holes, without any attachment conf to Fe 410 (Gde E-250) complete all as specified and directed.

S&F rolled mild steel in joist, channels, angles or tee sections, fixed ,post independently without connecting plates, etc.,conf to Fe 410 (Gde E-250) complete all as specified and directed.

S&F rolled mild steel in purlins /rafters of channels, squre/ rectangle tubes, angles or tee sections, fixed with MS angle cleats,plates etc incl all necessary welding , bolting etc. independently without connecting plates, etc.,conf to Fe 410 (Gde E-250) complete all as specified and directed.

M&L for Preparation of new or previosly untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

M&L for Excavating in post holes (or similar holes) as in hard/ dense soil, each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and directed.

M&L for Cement concrete 1:3:6 type C2 (using 40mm graded stone agrregate) as in foundation, filling and mass concrete complete all as specified and directed.

Removing old APP membrane of any thickness and description carefully without damaging the mother slab from roof and disposing off out side MD Land complete all as specified and directed.

Demolition of cement concrete in Roofs, floors (other than ground floors) of any thickness etc complete all as specified and directed.

M&L for providing 25mm thick cement concrete 1:2:4 type B0 (using12.5 mm graded stone aggregate) as in level course of roof/ chajja kerbs and making the surface even and smooth, including proving dummy/ constructions as per requirement at site and filling the joints with Fosroc joint filler as per manufacturer instructions complete all as specified and directed.

Supplying and applying waterproofing treatment to sound, moisture free concrete surface. System includes proper surface preparation to remove loose dust, dirt, loose mortar, curing compound etc., carry out cementitious injection grouting at leakage points and construction joints using cement slurry modified with Cebex 100-Plasticised expandive grout admixture supplied in 225 gm pouch, treatment of construction joints using polymer modified mortar prepared by using Nitobond SBR Latex, application of polymer modified vatta at floor-wall junction, filling of annular space around rain water outlet using Conbextra GP2 - Non-shrink cementitious grout. any undulated surface and pot holes shall be filled with Epoxy mortar to obtain sound/levelled surface. Application of primer Nitoproof WB Primer on sound mother slab surface. Followed by application of two coats of Nitoproof 600PF - Liquid applied single component pitch free polyurethane coating supplied in 25 kg drum coverage @ 2.3 kg/m2 to achieve 1.5 mm thickness in two coats complete including all tools and tackles as per manufacturer’s specifications. Coating shall be having crack bridging of 2 mm, Elongation (ASTMD 412) > 600 %, Tensile Strength (ASTM D412) – 2.5 N/mm2, Recovery from Elongation (ASTM D412) – 95 %, 85% Solid Content, Tear Resistance (ASTM D624) – 15 Kn/m, Shore A Hardness (ASTM D2240) – 60, Water vapour transmission not more than 1g/m2/hr, Water Permeability (DIN 1048) – Nil, Service Temperature – -40°C to 70°C, Flash Point > 70 °C HSE Guidelines: It is recommended to provide adequate general and local exhaust ventilation, provide protection to eye, face, hand and other skin by wearing appropriate gloves, goggles, face shields, respiratory protection etc. as directed in SDS of the product.

Supply only integral Waterproofing compound of approved make all as directed.

Supplying and laying seperation & protection layer- Geotextile membrane 150 gsm prior to protection screed complete all as specified and directed.

Taking down/refixing of top hood cover from existing rolling shutters after greasing , over oiling of all the components for easy operation realignment of guide channels bearing and tension spring, making good locking arrangement including cleaning etc (Area n exc 20 Sqm each) complete all as specified and directed.

Taking down/refixing of top hood cover from existing rolling shutters after greasing , over oiling of all the components for easy operation realignment of guide channels bearing and tension spring, making good locking arrangement including cleaning etc (Area exc 20 Sqm but n exc 30 Sqm each) complete all as specified and directed.

Taking down/refixing of top hood cover from existing rolling shutters after greasing , over oiling of all the components for easy operation realignment of guide channels bearing and tension spring, making good locking arrangement including cleaning etc (Area exc 30 Sqm but n exc 40 Sqm each) complete all as directed.

Taking down/refixing of rolling shutter of any description (With all components) and in any size and removing fron site area up to15.00 Sqm each complete all as directed.

Taking down/refixing of rolling shutter of any description (With all components)and in any size and removing fron site area exc 15.00 Sqm but n exc 25.00 Sqm complete all as specified and directed.

Supply and fix Steel rolling shutters, Thickness of latch 1.00mm thick without ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type complete all as specified and directed.

Supply and fix Steel rolling shutters, Thickness of latch 1.00mm thick with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: but gear operated type with bevel gear box and crank handle erected in position complete all as specified and directed.

S & F in repairs for helical wire spring of suitable ( Heavy duty ) size up to 35 cm fixed in repair by greasing etc complete and refixing covers in position complete all as specified and directed.

S & F in repairs for high tension helical wire sprial spring dia n exc 100 mm for anchoring rod complete all as specified and directed.

S & F in repairs for plain galvanised 1mm thick Class-2 mild steel sheeting in rolling shutter hood cover moulded to shape as requried, including fixing in position complete all as directed.

S & F in repairs for suspension shaft mild steel 50 mm dia complete all as specified and directed.

S & F in repairs for ball bearings for rolling shutterrs complete all as specified and directed.

S & F in repairs for bottom rail / lock rail suitable for rolling shutter complete all as specified and directed.

S&F Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

S&F in repairs 1mm thickness, 150mm dia Mild steel sheet eaves gutters, galvanised class 3, half round with rounded edges complete all as specified and directed.

S&F 150mm dia Angles (internal or external) or nozzle pieces (Out lets) complete all as specified and directed.

S&F 150mm dia Stop ends (for spigot or socket ends) complete all as specified and directed.

S&F in repairs Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed including taking down and refixing existing aluminium door shutter complete all as specified and directed.

M&L for cleaning the existing wall cracks throughly with water and wire brush and filling the cracks with crack seal as per manufacture instructions complete all as specified and directed. Make: Asian/ Fosroc as approved. Note: Height upto 12m from the GL and rate shall includes necessary scafolding

Taking down 15mm bore steel water tubing and connections complete all as specified and directed.

S&F 15 mm bore steel water tubing, ‘medium grade’ galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Refixing of 15mm bore old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and directed.

Taking down 20mm bore steel water tubing and connections complete all as specified and directed.

S&F 20 mm bore steel water tubing, ‘medium grade’ galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Refixing of 20mm bore old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and directed.

Supplying and laying of 16mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors, including fittings and fixtures such as elbow, bend, tee, reducers and also connecting to exisiting GI tubes, complete all as specified.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

S&F in repairs 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 15 mm bore ball brass valves, high pressure, with polythene float and fly- nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S&F in repairs 1000 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 20 mm bore ball brass valves, high pressure, with polythene float and fly- nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S&F in repairs 10 liters capacity PVC low level flushing cistern with ISI marked body etc complete all as specified and directed.

S&F in repairs 15 mm bore, 60 cm long PTMT connecting pipe fitted with unions to connect iron pipe to PVC pipe on both ends complete all as specified and directed.

S&F in repairs plastic water closet seat, white closed pattern, solid type with flat bottom, and cover and mild steel chromium plated hinging device complete all as specified and directed.

S&F in repairs brass chromium plated shower rose of 125 mm size with swivel joint including fixing to steel pipe or union complete all as specified and directed.

S&F in repairs for pillar taps 15 mm, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F in repairs 15 mm bore pillar taps of PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 15mm-110gms) complete all as specified and directed.

S&F in repairs 15 mm bore bib taps, cast copper alloy chromium plated long body fancy type with capstan head, screwed down, screwed for iron pipe complete all as specified and directed. (Note: Min Wt 575 Grams)

S&F in repairs 15 mm bore bib taps, cast copper ally chromium plated, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repairs 15 mm bore three in one Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F in repairs vitreous china squatting pan , ‘Orissa’ pattern, size 580 mm x 440 mm, white with integral foot rests, embedded and set in PCC 1:5:10 type E-2 and making good to floor including removing rubbish complete all as specified and directed.

S&F in repairs, vitreous China wash down water closet pan, (pedestal pattern), white, with and including plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, flush pipe for joining etc complete.

S&F in repairs sink made of stainless steel 1.00 mm thick kitchen with plugs, washers and wastes including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm and PVC waste pipe of 32mm bore and of suitable length etc complete all as specified & directed.

S&F in repair for vitreous China wash basin, white, flat back, size 580x450mm including necessary brackets,cp couplings, pvc waste pipes etc. complete all as specified and directed.

S&F in repair for vitreous China wash basin, white,counter type, size 550 x 425 x 180mm including necessary brackets,CP couplings, waste pipes etc. complete all as specified and directed.

Supply only for Pillar taps 15 mm, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F in repairs 15mm bore CP brass health faucet of 1.2m long including brass holders, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed

S&F in repairs 15mm bore CP brass two way bib cock, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed

S&F in repairs gun metal globe or gate valves with iron wheel head screwed both end for iron pipe and fixed to 20mm bore pipe complete all as specified and directed.

S&F in repairs gun metal globe or gate valves with iron wheel head screwed both end for iron pipe and fixed to 25mm bore pipe complete all as specified and directed.

S&F in repairs gun metal globe or gate valves with iron wheel head screwed both end for iron pipe and fixed to 15mm bore pipe complete all as specified and directed.

S&F in repair PVC floor trap/nahani trap incl stainless steel gratings, 75 mm dia of outlet, including jointing to waste pipe fixed in cement concrete type B1(1:2:4) complete all as specified and directed.

S&F in repairs 15 mm bore bib tap standard or PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 15mm 90gms/20mm-125gms) complete all as specified and directed.

S&F in repairs 15 mm bore stop valve of PTMT any colour high pressure screwed for iron pipe and fixed (minimum weight 15mm-90gms/20mm-112gms) complete all as specified and directed.

S/F in repair PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 110 mm dia including taking down old pipes complete all as specified and directed.

S/F in repair PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 75 mm dia including taking down old pipes complete all as specified and directed.

S/F in repair PVC (SWR) bends any radius 110 mm dia complete all as specified and directed.

S/F in repair PVC (SWR) bends any radius 75 mm dia complete all as specified and directed.

Supplying and laying in repairs of 50mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors, including fittings and fixtures such as elbow, bend, tee, reducers and also connecting to exisiting GI tubes, complete all as specified & directed.

S&F in repairs 15mm bore Ball valves high pressure of PTMT with epoxy coatedAluminium rod & highdensity plastic ball screwed for iron pipeand fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms) complete all as specified and directed.

S&F in repairs 20mm bore Ball valves high pressure of PTMT with epoxy coatedAluminium rod & highdensity plastic ball screwed for iron pipeand fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms) complete all as specified and directed.

S&F in repairs 15mm bore Ball valves high pressure of PTMT with epoxy coatedAluminium rod & highdensity plastic ball screwed for iron pipeand fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms) complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 sqm but not exceeding 4 sqm each and removing from site complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 sqm each and removing from site complete all as specified and directed.

Taking down Shutters of any description exc 1 sq. m but n exc 2 sqm each complete all as specified and directed.

S&F second class hard wood, plain, solid straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S&F MS hold fasts conforming to Fe -410 complete all as specified and directed.

M&L for cement concrete as in bed plates Type B0 1:2:4 using 12.5mm graded stone aggregate complete all as specified and directed.

M&L for treating small articles such as hold fasts with tar or coal tar black paint incl preparation complete all as specified and directed.

S&F Glazed and skeleton shutter 35mm thick open rebeted prepared to recived glass without sash bar complete all as specified and directed.

S&F 30 mm thick flush shutters solid core construction with block board core and plywood face panels and one face is covered with decoretive face veneer with lipping / frame to matchcommercial type on both sides complete all as specified and directed.

S&F factory made 100% soild wood plastic composite (WPC) door frame, single rebated 90mm x 45mm made from wood plastic composite (single extruded process) material with density 780 Kg/Cum, including necessary fittings and fixtures to fix the chowkat as per manufacture instructions complete all as specified and directed. Note: During fixing the chowkat the surfacrs of jambs shall be made in true plumb in cement plaster 1:4 as in making good or similar in wall tiles etc as per site requirement complete all as specified and directed.

All as per Item No 88.00 here in before but double door chowkat of size 125mm x 45mm complete all as specified and directed.

S&F Factory Made Solid PVC Moulded Door Shutter witth particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site complete all as specified and directed.

S&F Aluminium, anodised barrel tower bolt 150 mm complete all as specified and directed.

S&F Aluminium alloy , anodised sliding door bolt with hasp, staple ( Bolt type) and fixing clips of sheet, cast or extruded section or cast aluminium alloy and fixed 300 mm complete all as specified and directed.

S&F Aluminium handles fabricated type 150 mm complete all as specified and directed.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M&L for preparation of new wooden surfaces and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F Mild steel cold rolled Butt hings 100 mm medium weight complete all as specified and directed.

S&F aluminium powder coated frame for doors, windows, partitions and ventilators with one or more rebates including necessary jointing cleat for fixing etc complete all as specified and directed.

S&F anodised aluminium window, doors and ventilator shutter, sliding/ fixed type without sash bar , aluminium section weighing 0.55 Kg/Mtr including necessary jointing cleat glazing clips rubber packing anodised aluminium snap beading screws, rollers, locks etc complete all as specified and directed.

Hacking out old broken glass from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed.

M&L for sheet glass ordinary quality 4 mm thick fix in Aluminium/ steel, window/vent shutter area exc 0.50 Sqm in each pane complete all as specified and directed.

M&L for 3mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and directed.

S&F in repairs 100 mm butt hinges, medium weight, cold rolled mild steel complete all as specified and directed

S&F in repairs 150 mm long aluminium, anodised, or matt finished barrel tower bolts of extruded section complete all as specified and directed.

S&F in repairs 150 mm size extruded aluminium alloy bow handles, fabricated type with plate, matt or anodised finish complete all as specified and directed.

S&F in repairs floor door stopper 140mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F in repairs 60 cm long SS tubular towel rail 20-mm dia complete all as specified and directed.

S&F in repairs Aluminium alloy , anodised sliding door bolt with hasp, staple ( Bolt type) and fixing clips of sheet, cast or extruded section or cast aluminium alloy and fixed 300 mm complete all as specified and directed.

S&F in repairs 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and directed.

S&F in repairs 25mm bore stainless steel 304 grade curtain rods with suitable fancy type brackets and fixed in position using stainless steel screws complete all as specified and directed.

S&F in repairs stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples (304 Grade) complete all as specified and directed.

Taking down cement plaster from brick / concrete/ stone surfaces including racking out joint , hacking for key and scrubing down with water etc complete all as specified and directed.

M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces of any description in CM 1:6 and finishing the surface with Sagol Finish, complete all as specified and directed.

M&L for Rendering 20mm thick in two coats on fair faces of stone masonry surfaces in CM 1:6 (sagol finish) complete all as specified and directed.

M&L for preparation of newly plastered wall surface and applying two coats of water bound distemper over a coat of primer complete all as specified and directed.

Dismanting of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

S&F 605x 605mm size of grid Anodised aluminium snap grid frame work for false ceiling complete all as specified and directed.

S&F Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and directed.

S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed.

S&F 12mm thick Perforated particle board/ tiles for insula-tion and accoustic purposes, 60x60 cm in size, fixed with nails to timber framework or with staples on snap grid complete all as specified and directed.

S&F in repairs 12mm thick Perforated particle board/ tiles for insula-tion and accoustic purposes, 60x60 cm in size, fixed with nails to timber frameworkorwith staples on snap grid complete all as specified and directed.

Providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat/ curved/ sunked portion (any design as approved by Engineer In Charge) surface over GI frame work, or metal frame work and reinforced with G.I. wire mesh (Fillets, metal frame work and G.I. wire mesh paid separately) and making the surface even and smooth using wall care putty and applying two coats of interior emulsion paint over a coat of suitable primer complete all as specified and directed.

(a) Area exceeding 1.00 sqm but not exceeding 2.00 sqm each

M/S JAYCONSTRUCTION CO

M/s DEVRATAN ENTERPRISES