Interior decoration at different chambers and rooms at the office of Chief Engineer located at the second floor of the office of S.E., Northern Circle, Mangalbari, Malda under Malda Division, PWD.

Ply wood 5 ply With commercial ply on both faces, 6 mm thick

Ply wood 7 ply with teak ply on one face and commercial ply on another face, 9 mm thick

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss I maw suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost Of adhesive Of approved quality. 9.127.1 1.5 mm thick.

Providing and fixing false ceiling at all heights including providing and fixing Of frame work made Of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling With dash fastener 12.5 mm dia x 50 mm long with 6 mm dia Other fange Of cleat fixed to the angle hangers of 25x10xO.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15xO.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges Of 26 mm each having lips Of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, induding fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition With the help Of raw' plugs. 12.45.3) 12.5 mm thick tapered edge gypsum moisture resistant board

Providing and fixing ISI marked flush door shutters conforming to IS 2202 (Part l) decorative type, core of block board construction with frame Of 1st class hard wood and we' matched teak 3 ply veneering With vertical grains or cross bands and face veneers on both faces Of shutters. 9.20.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

providing and Fixing factory made PVC door frame made Of PVC extruded sections Of size 75 mm x 53 mm, having wall thickness 2.0 mm (t 0.2 mm). Both vertical sides of the frame reinforced with PVC profile of cross section size 28 mm x 30 mm x 2 mm thickness 0.2 mm) and 75 mm x 200 mm long, including reinforcing both ends of the top frame with PVC profile. PVC Door Frame and PVC reinforcement profile to be mitred cut, jointed and fusion welded together, including providing and fixing 3 nos Of 125 mm long stainless steel hinges to frame, fixing the frame with jamb with required nos & sizes of anchor dash fastener, all complete as per manufacturer's specification and direction of engineer- in-charge.

35 mm thick factory made Solid panel PVC Door shutter, made out Of single piece extruded soild PVC profiles. 5 mm (i 0.2 mm) thick, having styles & rails (except lock rail) of size 95 mmx 35 mm x 5 mm, out of which 75 mm shal be flat and 20 mm shall be tapered (on both side), having one side thickness Of 15 mm integrally extruded on the hinge side Of the profile for better screw holding power, including reinforcing with MS tube of size 40 mm X 20 mm x 1 mm, joints of styles & rails to be mitered cut & joint with the help of PVC solvent cement, self driven self tapping screws & M.S. rectangular pipes bracket of size 190 mm X 100 mm of cross section size 35 mm x 17 mm x I mm at each corner. Single piece extruded 5 mm thick solid PVC Lock rail Of size 115 mm x 35 mm, Out Of which 75 mm to be flat and 20 mm to be tapered at both ends, having 15 mm solid core in middle of rail section integrally extruded, fixing the styles & rails with the help of solvent and self driven self tapping screws of 125 mm x 11 mm, including providing 5 mm Single piece solid PVC extruded sheet inserted in the door as panel, all complete as per manufacturer's specification and direction Of Engineer-in-charge 9.142.2) Decorative finish (wood grained finish)

15 mm cement plaster on the rough side of single or half brick wall of mix . 13.2.2) 1:6 (1 cement: 6 fine sand)

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.