Construction of Regional Office Building at Bhubaneswar (Odisha)

Sl. Description Amount on Amount on Amount on

No. DSR-2023 DSR-2022 Non- DSR

1 Building Works

Civil Work 4,10,06,270.73

Internal Sanitary 15,86,283.05 4,41,655.36

Internal Electrical 23,28,436.23 51,40,184.60

Fire Fighting & Alarm System 7,18,215.30 1,34,376.94

Lift (13 Passanger) 12,61,739.20

IT Works 30,96,934.78

Furniture 31,06,305.48

2 External Development Works

A Septic Tank ( for 100 Users) 5,17,516.57

B External Electrical works 7,69,246.66 5,14,785.01

C External Water Supply 4,53,835.30

E Internal Pathway 16,03,721.70

F External Drainage 4,75,170.60

G Sewer Line 4,50,862.95

H Horticulture & Landscaping 1,87,990.15

I Rain Water Harvesting 5,04,269.05

Digitally signed by JAYA

NAME OF WORK :- Construction of Regional office Building at Kordah (Odisha)

ABSTRACT OF COST

DSR- AMOUNT DSR

S.N. DESCRIPTION OF ITEM QUANTITY UNIT RATES [M.R.

1.0 Earth work in excavation by mechanical means

(Hydraulic excavator)/manual means over areas

(exceeding 30 cm in depth, 1.5 m in width as well as

10 sqm on plan) including getting out and disposal of

excavated earth lead upto 50 m and for all lift, as

directed by Engineer-in charge.

2.0 Extra for every additional lift of 1.5 m or part thereof

in excavation / banking excavated or stacked 2.26.1 58.75 CUM 126.80 7,449.75

materials. All kinds of soil

Earth work in excavation by mechanical means

(Hydraulic excavator)/manual means over areas

(exceeding 30 cm in depth, 1.5 m in width as well as

3.0 10 sqm on plan) including getting out and disposal of

excavated earth lead upto 50 m and lift upto 1.5 m,

as directed by Engineerin-charge.

4.0 Excavating trenches by mechinical / manual means of

required width for pipes, cables, etc including

excavation for sockets, and dressing of sides,

ramming of bottoms, for all depth, including getting

out the excavated soil, and then returning the soil as

required, in layers not exceeding 20 cm in depth,

including consolidating each deposited layer by

ramming, watering, etc. and disposing of surplus

excavated soil as directed, within a lead of 50 m.

All kind of soil

Pipes, cables etc, not exceeding 80 mm dia. 2.10.1.2 81.00 Metre 352.15 28,524.15

5.0 Filling available excavated earth (excluding rock) in

trenches, plinth, sides of foundations etc. in layers not

exceeding 20cm in depth,consolidating each 2.25 382.44 CUM 196.00 74,958.53

deposited layer by ramming and watering, lead upto

50 m and lift upto 1.5 m.

6.0 Supplying and filling in plinth with sand under floors,

including watering, ramming,consolidating and 2.27 159.81 CUM 2123.75 3,39,402.86

dressing complete.

7.0 Excavating, supplying and filling of local earth

(including royalty) by mechanical transport upto a

lead of 5km also including ramming and watering of 2.25a 568.84 CUM 700.50 3,98,472.42

the earth in layers not exceeding 20 cm in trenches,

plinth, sides of foundation etc. complete.

Surface dressing of the ground including removing

vegetation and in-equalities not exceeding 15 cm

deep and disposal of rubbish, lead up to 50 m and lift

8.0 Supplying chemical emulsion in sealed containers

including delivery as specified.

Chlorpyriphos/ Lindane emulsifiable concentrate of

With Chlorpyriphos/Lindane E.C. 20% with 1%

B Concrete Work

11.0 Providing and laying in position cement concrete of

specified grade excluding the cost of centering and

shuttering - All work up to plinth level

1:3:6 (1 Cement : 3 coarse sand (zone-III) derived

from natural sources : 6 graded stone aggregate 20 4.1.5 175.74 Cum 7294.70 12,81,972.40

mm nominal size derived from natural sources)

Digitally signed by JAYA

DSR- AMOUNT DSR

S.N. DESCRIPTION OF ITEM QUANTITY UNIT RATES [M.R.

12.0 Providing and laying damp-proof course 50mm thick

with cement concrete 1:2:4 (1 cement : 2 coarse

sand (zone-III) derived from natural sources : 4 4.11 60.00 SQM 495.75 29,745.00

graded stone aggregate 20mm nominal size derived

from natural sources).

13.0 Extra for providing and mixing water proofing

material in cement concrete work in doses by weight per

of cement as per manufacturer's specification. 4.12 22.00 50kg 18.15 399.30

14.0 Providing & applying a coat of residual petroleum

bitumen of grade of VG-10 of approved quality using

1.7kg per square metre on damp proof course after 4.13 24.12 SQM 146.15 3,525.14

cleaning the surface with brushes and finally with a

piece of cloth lightly soaked in kerosene oil.

15.0 Making plinth protection 50mm thick of cement

concrete 1:3:6 (1 cement : 3 coarse sand (zone-III)

derived from natural sources : 6 graded stone

aggregate 20 mm nominal size derived from natural

sources) over 75mm thick bed of dry brick ballast 40 4.17 72.00 SQM 749.30 53,949.60

mm nominal size, well rammed and consolidated and

grouted with fine sand,including necessary

excavation,levelling & dressing & finishing the top

C Reinforced Cement Concrete

16.0 Centering and shuttering including strutting, propping

etc. and removal of form for all heights :

(a) Foundations, footings, bases of columns, etc. for

(b) Walls (any thickness) including attached pilasters,

butteresses, plinth and string courses etc. 5.9.2 SQM 842.50 -

(c) Suspended floors, roofs, landings, balconies and

access platform.

(d) Lintels, beams, plinth beams, girders, bressumers

(e) Columns,Pillars, Piers, Abutments, Posts and Struts.

(f) Stairs, (excluding Landings) except spiral staircases

(g) Weather shade, chajjas, corbels etc. including edges.

17.0 Steel reinforcement for R.C.C. work including

straightening, cutting, bending, placing in position

and binding all complete upto plinth level. Thermo- 5.22.6 23381.32 Kg 107.85 25,21,675.81

Mechanically Treated bars of grade Fe-500D or more.

18.0 Steel reinforcement for R.C.C. work including

straightening, cutting, bending, placing in position

and binding all complete above plinth level. Thermo- 5.22.A.6 50466.57 Kg 107.85 54,42,819.28

Mechanically Treated bars of grade Fe-500 D or more.

19.0 providing and laying in position ready mixed or site

batched design mix cement concrete for reinforced

cement concrete work; using coarse aggregate and

fine aggregate derived from natural sources, portland

pozzolana / ordinary portland /portland Slag cement,

admixtures in recommended proportions as per iS:

9103 to accelerate / retard setting of concrete, to

improve durability and workability without impairing

strength; including pumping of concrete to site of

laying, curing, carriage for all leads; but excluding the

cost of centering, shuttering, finishing and

Note: Extra cement up to 10% of the minimum

specified cement content in design mix shall be

payable separately. in case the cement content in

design mix is more than 110% of the specified

minimum cement content, the contractor shall have

Digitally signed by JAYA

DSR- AMOUNT DSR

S.N. DESCRIPTION OF ITEM QUANTITY UNIT RATES [M.R.

(I) All works upto plinth level 5.33.1

concrete of M25 grade with minimum cement content

(ii) All works above plinth level

concrete of M25 grade with minimum cement content

D Masonry Work

10 Brick work with non modular fly ash bricks conforming

to IS:12894, class designation 10 average

compressive strength in superstructure above plinth 6.34.2 298.10 CUM 8752.55 26,09,135.16

level up to floor V level in : Cement mortar 1:6 (1

cement : 6 coarse sand)

11 Brick work with common burnt clay modular bricks of

class designation 7.5 in foundation and plinth in: 6.20

Cement Mortar 1:6 (1 cement : 6 coarse sand). 6.2.2 180.20 CUM 6295.15 11,34,386.03

Half brick masonry with non modular fly ash bricks of

class designation 10, conformingio IS :12894, in

super structure above plinth upto floor V level. 6.45.2 720.00 SQM 1123.8 8,09,136.00

Cement mortar 1 : 4 (1 cement : 4 coarse sand)

12 Extra for providing and placing in position 2 Nos 6mm

dia. M.S. bars at every third course of half brick 6.15 58.30 SQM 104.80 6,109.84

E Cladding Work

13 Providing and fixing 18 mm thick gang saw cut,

mirror polished, premoulded and prepolished,

machine cut for kitchen platforms, vanity counters,

window sills , facias and similar locations of required

size, approved shade, colour and texture laid over 20

mm thick base cement mortar 1:4 (1 cement : 4 8.20

coarse sand), joints treated with white cement, mixed

with matching pigment, epoxy touch ups, including

rubbing, curing, moulding and polishing to edges to

give high gloss finish etc. complete at all levels.

Granite stone slab of colour black, Cherry/Ruby red

Area of slab above 0.50 sqm 8.2.2.2 52.63 SQM 5413.50 2,84,885.44

14.0 Extra for fixing marble /granite stone over and above

corresponding basic item, in facia and drops of width

upto 150 mm with epoxy resin based adhesive 8.4 75.00 RM 568.55 42,641.25

including cleaning etc. complete.

15.0 Extra for providing opening of required size & shape

for wash basins/ kitchen sink in kitchen platform,

vanity counters and similar location in

marble/Granite/stone work including necessary holes 8.5 10.00 EACH 978.70 9,787.00

for pillar taps etc. including moulding, rubbing and

polishing of cut edges etc. complete.

F Wood and PVC Work -

16.0 Providing and fixing ISI marked flush door shutters

conforming to IS : 2202 (Part I) decorative type, core

of block board construction with frame of 1st class

hard wood and well matched teak 3 ply veneering 9.20

with vertical grains or cross bands and face veneers

on both faces of shutters.

35 mm thick including ISI marked Stainless Steel butt

hinges with necessary screws

18.0 Providing laminated veneer lumber conforming to

IS:14616 and TAD -15: 2001 (Part B) in factory made

frames of doors, windows, clerestory windows and

other frames, wrought framed and fixing in position

19.0 Providing and fixing aluminium handles ISI marked

anodised (anodic coating not less than grade AC 10 as

per IS : 1868) transparent or dyed to required colour 9.10

with necessary screws etc. complete :

Digitally signed by JAYA

DSR- AMOUNT DSR

S.N. DESCRIPTION OF ITEM QUANTITY UNIT RATES [M.R.

20.0 Providing and fixing aluminium hanging floor door

stopper ISI marked anodised (anodic coating not less

than grade AC 10 as per IS :1868) transparent or 9.101 15.00 Each 70.40 1,056.00

dyed to required colour or shade with necessary

screws etc. complete:

Twin Rubber stopper

21.0 Providing & fixing bright finished brass 100mm

mortice latch and lock with 6 levers and a pair of lever

handles with necessary screws etc. complete (Best 9.76 15.00 Each 854.65 12,819.75

make of approved

22.0 Providing & fixing bright finished brass night latch of

approved quality including necessary screws etc. 9.78 1.00 Each 1183.30 1,183.30

23.0 Providing & fixing IS:3564 marked aluminium Die cast

body tubular type universal hydraulic door closer with 9.83 15.00 Each 1124.85 16,872.75

necessary accessories and screws etc. complete

24 Providing and fixing aluminium sliding door bolts ISI

marked anodised (anodic coating not less than grade

AC 10 as per IS: 1868) transparent or dyed to 9.96

required colour or

shade with nuts and screws etc. complete:

25 Providing and fixing aluminium tower bolts ISI

marked anodised (anodic coating not less than grade

AC 10 as per IS : 1868 ) transparent or dyed 9.97

toreqired colour or shade

with necessary screws etc.

26 Providing and fixing factory made uPVC glazed/wire

mesh windows/doors comprising of lead free uPVC

multi-chambered frame, sash and mullion/coupler

(where ever required) extruded profiles having

minimum wall thickness of 1.70 mm for Series R1 and

R2 profiles and 2.10 mm for Series R3 and R4 profiles

conforming to EN: 12608 in any shape, colour and

design duly reinforced with galvanized mild steel

section made of required shape & size as per CPWD

Specification, uPVC extruded glazing beads, interlocks

and Inline sash adaptor (where ever required) of

appropriate dimension, EPDM gasket, hardware, SS

304 grade fasteners of minimum 8 mm dia with

countersunk head, comprising of matching polyamide

PA6 grade sleeve for fixing frame to finished wall as

per IS 1367 : Part 1 to 14, plastic packers, plastic

caps and necessary stainless steel screws etc. Profile

of frame, sash & mullion (if required) shall be mitred

cut and fusion welded/mechanically jointed duly

sealed at all corners, including drilling of holes for

fixing hardware and drainage of water etc. After fixing

frame the gap between frame and adjacent finished

wall shall be filled with weather proof silicon sealant

over backer rod of approved size and quality, all

complete as per approved drawing conforming to

CPWD specification & direction of Engineer-in-Charge.

Two track two panels sliding window with Aluminium

channel for roller track, wool pile, nylon rollers with 9.147.A1

Using R2 series with frame (40mm & above) x (40mm

& above) & sash (25mm & above) x (50mm & above)

with zinc alloy (zamak) powder coated touch locks 9.147.A1.1

with hook (Height upto 1.2 metre).

27.0 Providing and fixing factory made P.V.C. door frame

of size 50x47 mm with a wall thickness of 5 mm,

made out of extruded 5mm rigid PVC foam sheet,

mitred at corners and joined with 2 Nos of 150 mm

long brackets of 15x15 mm M.S. square tube, the

vertical door frame profiles to be reinforced with

19x19 mm M.S. square tube of 19 gauge, EPDM

rubber gasket weather seal to be provided through

out the frame. The door frame to be fixed to the wall

using M.S. screws of 65/100 mm size, complete as

per manufacturer’s specification and direction of

Engineer-in-Charge.

Digitally signed by JAYA

DSR- AMOUNT DSR

S.N. DESCRIPTION OF ITEM QUANTITY UNIT RATES [M.R.

28.0 Providing and fixing factory made panel PVC door

shutter consisting of frame made out of M.S. tubes of

19 gauge thickness and size of 19 mm x 19 mm for

styles and 15x15 mm for top & bottom rails. M.S.

frame shall have a coat of steel primers of approved

make and manufacture. M.S. frame covered with 5

mm thick heat moulded PVC ‘C’ channel of size 30

mm thickness, 70 mm width out of which 50 mm shall

thick mm shall be tapered

laminated PVC doorinshutters

29.0 Providing and fixing M.S. grills of required pattern in

frames of windows etc. with M.S. flats, square or

round bars etc. including priming coat with approved 9.48.2 1000.00 Kg 238.35 2,38,350.00

steel primer all complete.

30 Structural steel work riveted, bolted or welded in built

up sections, trusses and frame work, including

cutting, hoisting,fixing in position and applying a 10.20 150.00 Kg 133.70 20,055.00

prime coat of approved steel primer all complete.

31 With ready mixed red oxide zinc chromate primer of

approved brand and manufacture on steel work 13.50.4 450.00 Sqm 36.10 16,245.00

32 Providing & fixing at all heights, levels and locations

colour finish Aluminium alloy roofing sheets of alloy

IS designation 31500, temper Hx8 conforming to IS

737 and dimensions as per IS code 2676 with

characteristics of good formability and corrosion

resistance. The profile sheets shall be fixed to truss

members in slope or required pitch or curvature with 12.65.

Hex cap headed self drilling/tapping Stainless steel

screws M6, 50 mm long with 3 mm EPDM seal washer

etc. all inclusive of labour, scaffolding, T&P and

sundries etc. complete as per directions of the

Engineer-In-Charge. (Cost of truss/frame work shall

be paid separately)

0.71mm Aluminium colour coated profile with center

to center pitch of 175 mm, depth of 46mm, top crest

width of 41mm, bottom valley width of 80mm, overall 12.65.5 50.00 Sqm 1865.60 93,280.00

profile width of 1144mm, cover width 1050mm

33.0 Providing and fixing 1mm thick M.S. sheet door with

frame of 40x40x6 mm angle iron and 3 mm M.S.

gusset plates at the junctions and corners, all 10.50

necessary fittings complete, including applying a

priming coat of approved steel primer

Using M.S. angels 40x40x6 mm for diagonal braces

34.0 Steel work welded in built up sections/ framed work,

including cutting, hoisting, fixing in position and

applying a priming coat of approved steel primer 10.25

using structural steel etc. as required. In gratings,

frames, guard bar, ladder, railings, brackets,

In gratings, frames, guard bar, ladder, railings,

brackets, gates and similar works.

35.0 Providing and fixing stainless steel ( Grade 304)

railing made of Hollow tubes, channels, plates etc.,

including welding, grinding, buffing, polishing and

making curvature (wherever required) and fitting the

same with necessary stainless steel nuts and bolts

complete, i/c fixing the railing with necessary 10.28 300.00 KG 772.40 2,31,720.00

accessories & stainless steel dash fasteners , stainless

steel bolts etc., of required size, on the top of the

floor or the side of waist slab with suitable

arrangement as per approval of Engineer-in-charge.

36.0 Marble stone flooring with 18mm thick marble stone

as per sample of marble approved by Engineer-in-

charge over 20 mm (average) thick base of cement

mortar 1:4 (1 cement : 4 coarse sand) laid and 11.23

jointed with grey cement slurry including rubbing and

polishing complete with :

Digitally signed by JAYA

DSR- AMOUNT DSR

S.N. DESCRIPTION OF ITEM QUANTITY UNIT RATES [M.R.

37.0 Extra for pre finished nosing to treads of steps of

marble/granite stone.

38.0 Extra For marble stone flooring in treads of steps and

riser using single length up to 2.00 metre 11.25 68.00 SQM 851.80 57,922.40

39.0 Providing and fixing Ist quality ceramic glazed wall

tiles conforming to IS : 15622 (thickness to be

specified by the manufacturer ) of approved make in

all colours, shades except burgundy, bottle green,

black of any size as approved by Engineer-in-Charge,

in skirting, risers of steps and dados over 12 mm 8.31 320.50 SQM 1267.95 4,06,377.98

thick bed of cement Mortar 1:3 (1 cement : 3 coarse

sand) and jointing with grey cement slurry @ 3.3kg

per sqm including pointing in white cement mixed

with pigment of matching shade complete

40.0 Providing and laying flamed finish Granite stone

flooring in required design and patterns, in linear as

well as curvilinear portions of the building all

complete as per the architectural drawings with 18

mm thick stone slab over 20 mm (average) thick base

of cement mortar 1:4 (1 cement : 4coarse sand) laid

and jointed with cement slurry and pointing with

white cement slurry admixed with pigment of

matching shade including rubbing, curing and

polishing etc. all complete as specified and as

directed by the Engineer-in-Charge :Flamed finish

granite stone slab Jet Black, Cherry Red, Elite

Brown, Cat Eye or equivalent.

41.0 Kota stone slab flooring over 20 mm (average) thick

base laid over and jointed with grey cement slurry

mixed with pigment to match the shade of the slab, 11.26

including rubbing and polishing complete with base of

cement mortar 1 : 4 (1 cement : 4 coarse sand) :

42.0 Kota stone slabs 20 mm thick in risers of steps,

skirting, dado and pillars laid on 12 mm (average)

thick cement mortar 1:3 (1 cement: 3 coarse sand)

and jointed with grey cement slurry mixed with 11.27 10.00 SQM 2354.70 23,547.00

pigment to match the shade of the slabs, including

rubbing and polishing complete

43.0 Providing and laying vitrified floor tiles in different

sizes (thickness to be specified by the manufacturer)

with water absorption less than 0.08% and

conforming to IS: 15622, of approved make, in all

colours and shades, laid on 20mm thick cement 11.41 318.75 SQM 1577.15 5,02,716.56

mortar 1:4 (1 cement : 4 coarse sand), jointing with

grey cement slurry @ 3.3 kg/ sqm including grouting

with white cement and matching pigments etc.,

Double charge vitrified tile polished finish of size

Size of Tile 600 x 1200 mm sqm 11.41A.1.3

44.0 Providing and laying Vitrified tiles in different sizes

(thickness to be specified by the manufacturer), with

water absorption less than 0.08% and conforming to

IS: 15622, of approved brand & manufacturer, in all

colours and shade, in skirting, riser of steps, laid with

cement based high polymer modified quick set tile

adhesive (water based) conforming to IS: 15477, in

average 6 mm thickness, including grouting of joints

(Payment for grouting of joints to be made

Digitally signed by JAYA

DSR- AMOUNT DSR

S.N. DESCRIPTION OF ITEM QUANTITY UNIT RATES [M.R.

45.0 Providing and laying Polished Granite stone flooring in

required design and patterns, in linear as well as

curvilinear portions of the building all complete as per

the architectural drawings with 18 mm thick stone

slab over 20 mm (average) thick base of cement

mortar 1:4 (1 cement : 4 coarse sand) laid and

jointed with cement slurry and pointing with white 11.56.1 175.50 SQM 4481.30 7,86,468.15

cement slurry admixed with pigment of matching

shade including rubbing, curing and polishing etc. all

complete as specified and as

directed by the Engineer-in-Charge.

Polished Granite stone slab colour of Black,

Cherry/Ruby Red or equivalent

46.0 Providing and fixing Heat Resistant Terrace Tiles (300

mm x 300 mm x 20 mm) with SRI (solar refractive

index) > 78, solar reflection > 0.70 and initial

emittance > 0.75 on waterproof and sloped surface of

terrace, laid on 20 mm thick cement sand mortar in

the ratio of 1:4 (1 cement : 4 coarse sand) and 12.55

grouting the joints with mix of white cement & marble

powder in ratio of 1:1, including rubbing and polishing

of the surface upto 3 cuts complete, including

providing skirting upto 150 mm height along the

parapet walls in the same manner.

Providing and fixing false ceiling at all heights

including providing and fixing of frame work made of

special sections, power pressed from M.S. sheets and

galvanized with zinc coating of 120 gms/sqm (both

side inclusive) as per IS : 277 and consisting of angle

cleats of size 25 mm wide x 1.6 mm thick with flanges

of 27 mm and 37mm, at 1200 mm centre to centre,

one flange fixed to the ceiling with dash fastener 12.5

mm dia x 50 mm long with 6 mm dia bolts, other

47.0 flange of cleat fixed to the angle hangers of 25x1 12.45

0x0.50 mm of required length with nuts & bolts of

required size and other end of angle hanger fixed with

intermediate G.I. channels 45x15x0.9 mm running at

the spacing of 1200 mm centre to centre, to which

the ceiling section 0.5 mm thick bottom wedge of 80

mm with tapered flanges of 26 mm each having lips

of 10.5 mm, at 450 mm centre to centre, shall be

fixed in a direction perpendicular to G.I. intermediate

channel with connecting clips made out of2.64 mm

12.5 mm thick tapered edge gypsum plain board

48.0 12 mm cement plaster of mix : 13.1

49.0 6 mm cement plaster on celling (a) 1:3(1 cement:3

50.0 18 mm cement plaster in two coats under layer 12

mm thick cement plaster 1:5 (1 cement : 5 coarse

sand) finished with a top layer 6 mm thick cement 13.11 781.06 SQM 518.55 4,05,018.66

plaster 1:6 (1 cement : 6 fine sand).

51.0 Providing and applying plaster of paris putty of 2mm

thickness over plastered surface to prepare the 13.26 3412.27 SQM 262.70 8,96,403.33

surface even and smooth complete.

52.0 Finishing walls with textured exterior paint of

required shade: New work (Two or more coats applied

@ 3.28 ltr/10 sqm) over and including priming coat of 13.45.1 781.06 SQM 223.60 1,74,645.02

exterior primer applied @ 2.20kg/10 sqm

53.0 Finishing with Deluxe Multi surface paint system for

interiors and exteriors using Primer as per 13.48

manufacturers specifications

Two or more coats applied on walls @ 1.25 ltr/10 sqm

over and including one coat of Special primer applied 13.48.1 2631.21 SQM 193.70 5,09,665.38

@ 0.75 ltr /10 sqm

54.0 Colour washing such as green, blue or buff to give an

New work (two or more coats) with a base coat of

J ALUMINIUM WORK

Digitally signed by JAYA

DSR- AMOUNT DSR

S.N. DESCRIPTION OF ITEM QUANTITY UNIT RATES [M.R.

55.0 Providing and fixing aluminium work for doors,

windows, ventilators and partitions with extruded built

up standard tubular sections/ appropriate Z sections

and other sections of approved make conforming to

IS: 733 and IS: 1285, fixing with dash fasteners of

required dia and size, including necessary filling up

the gaps at junctions, i.e. at top, bottom and sides

with required EPDM rubber/ neoprene gasket etc.

Aluminium sections shall be smooth, rust free, 21.1

straight, mitred and jointed mechanically wherever

required including cleat angle, Aluminium snap

beading for glazing / paneling, C.P. brass / stainless

steel screws, all complete as per architectural

drawings and the directions of Engineer-in-charge.

(Glazing, paneling and dash fasteners to be paid for

For fixed portion 21.1.1

Powder coated aluminium (minimum thickness of

powder coating 50 micron)

56.0 Providing and fixing glazing in aluminium door,

window, ventilator shutters and partitions etc. with

EPDM rubber / neoprene gasket etc. complete as per

the architectural drawings and the directions of 21.30

engineer-in-charge. (Cost of aluminium snap beading

shall be paid in basic item):

With float glass panes of 5 mm thickness(wt not less

then 12.5 kg/sqm)

57.0 Filling the gap in between aluminium frame &

adjacent RCC/ Brick/ Stone work by providing

weather silicon sealant over backer rod of approved 21.8

quality as per architectural drawings and direction of

Engineer-in-charge complete.

Upto 5mm depth and 5 mm width 21.8.1 350.00 M 96.75 33,862.50

58.0 Providing and fixing double action hydraulic floor

spring of approved Providing and fixing double action

hydraulic floor spring of approved brand and

manufacture conforming to IS : 6315, having brand

logo embossed on the body / plate with double spring

mechanism and door weight upto 125 kg, for doors,

including cost of cutting floors, embedding in floors as

required and making good the same matching to the

existing floor finishing and cover plates with brass

pivot and single piece M.S. sheet outer box with slide

plate etc. complete as per the direction of Engineer-in-

With stainless steel cover plate minimum 1.25 mm

59.0 Add for plaster drip course/ groove in plastered

surface or moulding to r.c.c. projections.

60.0 Providing and fixing 12mm thick frameless toughened

glass Providing and fixing 12mm thick frameless

toughened glass door shutter of approved brand and

manufacture, including providing and fixing top &

bottom pivot & double acting hydraulic floor spring

type fixing arrangement and making necessary holes

etc. for fixing required door fittings, all complete as

per direction of Engineer in charge (Door handle, lock

and stopper etc. to be paid separately

61.0 Providing and fixing Brass 100mm mortice latch and

lock with 6 Providing and fixing Brass 100mm mortice

latch and lock with 6 levers without pair of handles

(best make of approved quality) for aluminium doors 21.13 10.00 EACH 528.85 5,288.50

including necessary cutting and making good etc.

Digitally signed by JAYA

DSR- AMOUNT DSR

S.N. DESCRIPTION OF ITEM QUANTITY UNIT RATES [M.R.

62.0 Providing and supplying aluminium extruded tubular

and other aluminium sections as per the architectural

drawings and approved shop drawings , the

aluminium quality as per grade 6063 T5 or T6 as per

BS 1474,including super durable powder coating of 60-

80 microns conforming to AAMA 2604 of required

colour and shade as approved by the Engineer-in- 25.1 230.00 KG 414.30 95,289.00

Charge. (The item includes cost of material such as

cleats, sleeves, screws etc.necessary for fabrication of

extruded aluminium frame work. Nothingextra shall

be paid on this account). The weight of aluminium

extruded section shall be taken for purpose of

63.0 Designing, fabricating, testing, protection, installing

and fixing in positionsemi (grid) unitized system of

structural glazing (with open joints) forlinear as well

as curvilinear portions of the building for all heights 25.2 20.00 SQM 3510.50 70,210.00

and alllevels, including:

(a) Structural analysis & design and preparation of

shop drawings for the specified design loads

64.0 Providing, assembling and supplying vision glass

panels (IGUs) comprising of hermetically-sealed 6-12-

6 mm insulated glass (double glazed) vision panel

units of size and shape as required and specified,

comprising of an outer heat strengthened float glass 6 25.3 20.00 SQM 3718.70 74,374.00

mm thick, of approved colour and shade with

reflective soft coating on surface # 2 of approved

colour and shade, an inner Heat strengthned clear

float glass 6 mm thick, spacer tube 12 mm wide,

65.0 Extra for openable side / top hung vision glass panels

(IGUs) including providing and supplying at site all

accessories and hardwares for the openable panels as

specified and of the approved make such as heavy

duty stainless steel friction hinges, min 4 -point

cremone locking sets with stainless steel plates,

handles, buffers etc. including necessary stainless 25.4 20.00 SQM 3671.50 73,430.00

steel screws/ fasteners, nuts, bolts, washers etc. all

complete as per the Architectural drawings, as per the

approved shop drawings, as specified and as directed

by the Engineer- in-Charge.

66.0 Providing, fabricating and supplying shadow box of

required size and shape, for fixing in the spandrel

portion of the structural glazing, in linear as well as

curvilinear portions of the building by providing semi -

rigid, inorganic, non-combustible fibre glass wool

insulation 50 mm thick, conforming to IS: 8183 and

BS: 3958 Part 5. The insulation layer shall have facing

(factory bonded on surface # 1 of the fibre glass

insulation layer), of black non-woven fibre glass 25.5 20.00 SQM 2159.65 43,193.00

tissue of nominal thickness 0.5 mm and nominal mass

not less than 60 gm /sqm, made of randomly oriented

glass fibres distributed in a binder by a wet-lay

process including fixing 1.5 mm thick solid aluminum

sheet backing using, 6 mm thick cement board

including SS rivets, nuts, bolts, washers etc complete.

67.0 Designing, fabricating, testing, installing and fixing in

position Curtain Wall with Aluminium Composite Panel 8.32 20.00 SQM 5015.05 1,00,301.00

Cladding, with open grooves for linear as well as

Digitally signed by JAYA

DSR- AMOUNT DSR

S.N. DESCRIPTION OF ITEM QUANTITY UNIT RATES [M.R.

68.0 Providing and supplying Spandrel Glass Panels

comprising of 6 mm thick heat strengthened

monolithic float glass of approved colour and shade

with reflective soft coating on surface # 2 of approved

colour and shade so as to match the colour and shade

of the IGUs in the vision panels etc. ,all complete for

the required performances as specified, as per the

Architectural drawings, as per the approved shop

drawings, as specified, and as directed by the

Engineer- in- Charge.For payment, only the actual

area of glass on face # 1 of the glass panels (but

excluding the area of grooves and weather silicone

sealant) provided and fixed in position, shall be 25.6 20.00 SQM 2450.15 49,003.00

measured in sqm. (Payment for fixing of Spandrel

Glass Panels in the curtain glazing is included in cost

of relevant Item*).“(i) Coloured tinted float glass 6

mm thick substrate with reflective soft coating on face

# 2, having properties as visible Light transmittance

(VLT) of 25 to 35 %, Light reflection internal 10 to

15%, light reflection external 10 to 20 %, shading

coefficient (0.25- 0.28) and U value of 3.0 to 3.3

W/m2 K etc . . The properties of performance glass

shall be decided by technical sanctioning authority as

per the site requirement

69.0 Design supply & installation of suspended Spider

Glazing system designed to withstand the wind

pressure as per IS 875 (Part-III). The Suspended

System held with Spider Fittings of SS-316 Grade

Steel of approved manufacturer with glass panel

having 12 mm thick clear toughened glass held

together with SS- 316 Grade Stainless steel Spider &

bolt assembly with laminated glass fins 21 mm thick.

The Glass fins and glass panel assembly shall be

connected to Slab/beams by means of SS- 316 Grade

stainless steel brackets & Anchor bolts and at the

bottom using SS channel of 50x25x2 mm using

fastener & anchor bolts, non staining weather sealants 25.80 25.00 SQM 9502.35 2,37,558.75

of approved make, Teflon/ nylon bushes and

separators to prevent bi-metallic contacts, all

complete to perform as per specification and

approved drawings. The complete system to be

designed to accommodate thermal expansion &

seismic movements etc. The joints between glass

panels (6 to 8 mm) and gaps at the perimeter & in U

channel of the assembly to be filled with non staining

weather sealant, so as to make the entire system fully

water proof & dust proof. The rate shall include all

design, Engineering and shop drawing including

approval from structural designer, labour, T&P,

scaffolding, other incidental charges including

70.0 Providing and applying integral crystalline slurry of

hydrophilic in nature for waterproofing treatment to

the RCC structures like retaining walls of the

basement, water tanks, roof slabs, podiums,

reservior, sewage & water treatment plant, tunnels /

subway and bridge deck etc., prepared by mixing in

the ratio of 5 : 2 (5 parts integral crystalline slurry : 2

parts water) for

vertical surfaces and 3 : 1 (3 parts integral crystalline

slurry : 1 part water) for horizontal surfaces and

applying the same from negative (internal) side with

the help of synthetic fiber brush. The material shall 22.23

meet the requirements as specified in ACI-212-3R-

2010 i.e by reducing permeability of concrete by more

than 90% compared with control concrete as per DIN

1048 and resistant to 16 bar hydrostatic pressure on

negative side. The crystalline slurry shall be capable

of self-healing of cracks up to a width of 0.50mm. The

work shall be carried out all complete as per

specification and the direction of the engineer-in-

charge. The product performance shall carry

guarantee for 10 years against any leakage.

For vertical surface two coats @ 0.70 kg per sqm per

For horizontal surface one coat @1.10 kg per sqm.

Digitally signed by JAYA

DSR- AMOUNT DSR

S.N. DESCRIPTION OF ITEM QUANTITY UNIT RATES [M.R.

71.0 Providing and laying water proofing treatment in

sunken portion of WCs, bathroom etc., by applying

cement slurry mixed with water proofing cement

compound consisting of applying : (a) First layer of

slurry of cement @ 0.488 kg/sqm mixed with water

proofing cement compound @ 0.253 kg/ sqm. This

layer will be allowed to air cure for 4 hours.

(b) Second layer of slurry of cement @ 0.242 kg/sqm

mixed with water proofing cement compound @ 0.126

kg/sqm. This layer will be allowed to air cure for 4

hours followed with water curing for 48 hours.

The rate includes preparation of surface, treatment

and sealing of all joints, corners, junctions of pipes

and masonry with polymer mixed slurry.

72.0 Providing and laying in situ seven course water

proofing treatment Providing and laying in situ seven

course water proofing treatment with APP (Atactic

poly-propylene) modified Polymeric memberane over

roof consisting of first coat of bitumen primer @ 0.40

litre per sqm, 2nd, 4th & 6th courses of bonding

material @ 1.20 Kg/sqm, which shall consist of blown

type bitumen of grade 85/25 conforming

to IS : 702, 3rd and 5th layers of roofing membrane

APP modified Polymeric membrane 1.5 mm thick of

2.25 Kg/sqm weight consisting of five layers

prefabricated with centre core as 20 micron HMHDPE 14.86 391.00 SQM 730.55 2,85,645.05

film sandwiched on both sides with polymeric mix and

the polymeric mix is protected on both side with 20

micron HMHDPE film. 7th, the top most layer shall be

finished with brick tiles of class designation 10

grouted with cement mortar 1:3 (1cement : 3 fine

with 2% integral water proofing compound by weight

of cement over a 12 mm layer of cement mortar 1:3

(1 cement : 3 fine sand) and finished neat (item of

laying brick tiles shall be paid for separately

Providing and fixing 24 gauge- chicken wire mesh at

the junction of masonry work and RCC work or on any

other place as directed to receive plaster including

fixing with nails, raw plugs at all heights below and NS-1 230.00 SQM 240.09 55,219.84

above highest plinth level including scaffolding etc

complete as directed.

Manufacturing, supplying and fixing signage board

.Providing and fixing signages on the wall or with any

other required structure . Each signboard to be fixed

strictly as per the Harmonised Guidelines & Space

Standards for Barrier Free Built Environment for NS-2

persons with Disability, issued By MOUD, Govt. of

India, and as as per approved drawings and complete

as per the directions of Engineer – In – Charge.

a Light board with Tube Light and frame 5.00 SQM 3318.15 16,590.75

b Sun board vinyl 3 mm thick 10.00 SQM 1253.52 12,535.23

c Sun board vinyl 5 mm thick 5.00 SQM 1401.00 7,004.98

d ACP Sheet Board 5.00 SQM 1401.00 7,004.98

e Acrylic Sign Board 5.00 SQM 3465.62 17,328.12

Digitally signed by JAYA

Construction of Regional office Building at Khurdha (Odisha)

1 Sanitary Installations & Internal Water Supply UNITS QUANTITY RATES DSR AMOUNT NSOR AMOUNT

Providing and fixing white vitreous china pedestal type

water closet (European type W.C. pan) with seat and

lid, 10 litre low level white P.V.C. flushing cistern,

including flush pipe, with manually controlled device

2 1.2 (handle lever), conforming to IS : 7231, with all fittings 17.2.1 00.1.12 6973 83676

and fixtures complete, including cutting and making

good the walls and floors wherever required W.C. pan

with ISI marked white solid plastic seat and lid

17.10 Providing and fixing Stainless Steel A ISI 304 (18/8)

kitchen sink as per IS 13983 with C.I. brackets and

3 stainless steel plug 40 mm including painting of fittings

and brackets, cutting and making good the walls

wherever required :

17.10.1.3Kitchen sink with drain board 510x1040 mm bowl

17.10.2.1Kitchen sink with out drain board 610x510 mm bowl

17.31 Providing and fixing 600x450 mm beveled edge mirror

of superior glass (of approved quality) complete with 6

6 mm thick hard board ground fixed to wooden cleats Each 8 1607.95 12863.6

with C.P. brass screws and washers complete.

17.28 Providing and fixing P.V.C. Waste pipe for sink or

7 wash basin including P.V.C. waste fittings complete.

8 17.28.2 Semi rigid pipe

17.22A Providing and fixing CP Brass 32mm size Bottle Trap of

10 approved quality & make and as per the direction of Each 13 1034.8 13452.4

Engineer-in-charge.

17.22B Providing and fixing CP Brass Single lever telephonic

11 wall mixer of quality & make as approved by Engineer

12 a. 15 mm nominal dia Each 2 6940.75 13881.5

13 17.34 Providing and fixing toilet paper holder :

17.78 Providing and fixing white vitreous china extended wall

mounting water closet of size 780x370x690 mm of

approved shape including providing & fixing white

vitreous china cistern with dual flush fitting, of flushing

15 capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), Each 12 14999.15 179989.8

including seat cover, and cistern fittings, nuts, bolts

17.80 Providing and fixing white vitreous china battery based

infrared sensor operated urinal of approx. size 610 x

390 x 370 mm having pre & post flushing with water

16 (250 ml & 500 ml consumption), having water inlet Each 12 7979.2 95750.4

from back side, including fixing to wall with suitable

brackets all as per manufacturers specification and

direction of Engineer-in-charge.

18.5 Providing and fixing C.P. brass bib cock of approved

quality conforming to IS:8931 :

18 18.49.1 15 mm nominal bore Each 4 506.8 2027.2

18.5 Providing and fixing C.P. brass long body bib cock of

19 approved quality conforming to IS standards and

weighing not less than 690 gms.

18.5 Providing and fixing C.P. brass angle valve for basin

21 mixer and geyser points of approved quality

conforming to IS:8931

22 18.53.1 15 mm nominal bore Each 2 574.3 1148.6

18.2 Providing and fixing C.P. brass shower rose with 15 or

NS-88 Providing and fixing stainless steel grating approved

quality and colour.

18.53A Providing and fixing C.P. Brass extension nipple (size

27 15mmx50mm) of approved make and quality as per Each 100 74 7400

direction of Engineer-in-charge.

Providing and fixing white vitreous china wash basin

with special fabricated brackets painted white, faucets

as required, 32 mm C.P. brass waste.32 mm C.P. brass

28 bottle trap & pipe to wall with rubber adopter for waste

connection and C.P. brass wall flange complete in all

respects including cutting and making good the walls

where required.

NS-54 Providing white viterous china Under counter Oval

29 Wash Basin with brackets, 32 mm C.P. brass waste of Each 8 2641.198036 21129.58

standard pattern.

NS-55 Providing white viterous china Flat back Wash Basin

30 with brackets, 32 mm C.P. brass waste of standard Each 3 2729.23797 8187.71

NS-56 Providing 450 mm long C.P. copper connection pipe

with 15 mm couplings.

Digitally signed by JAYA

1 Sanitary Installations & Internal Water Supply UNITS QUANTITY RATES DSR AMOUNT NSOR AMOUNT

NS-57 Providing and fixing C.P. brass 15 mm nominal bore

two way bib cock approved quality.

NS-58 Providing and fixing C.P. cast brass twin coat hooks

35 fixed to PVC rawl plug with SS screws approved quality. Each 13 704.3194762 9156.15

NS-59 Providing and fixing health faucet with 1 m long flexible

36 tube and wall hook including all fittings approved Each 12 1291.252373 15495.03

NS-60 Providing and fixing 15mm C.P brass Sink Mixer for

37 kitchen sink with swinging spout complete. Including Each 2 4343.303436 8686.61

cutting and making good the walls wherever required .

NS-61 Providing and fixing of C.P. brass 600 mm size towel

38 rail equivalent fixed with C.P. brass screws complete in Each 11 1614.065466 17754.72

NS-62 Providing and fixing of C.P. brass Soap Dish Make

39 equivalent fixed with C.P. brass screws complete in all Each 3 939.0926349 2817.28

NS-63 Providing and fixing liquid soap dispenser including all

fittings complete.

NS-64 Providing & fixing SS Grab Bar Euronics & SS Grab Rail

41 Euronics Model No. EGR 01 or approved Each 2 1790.145335 3580.29

equivalent,Including cutting and making good the walls

wherever required.

NS-65 Providing and Fixing of C.P. Brass Shower set

comprising of :

One No. CP brass Single Lever Concealed Diverter .

One No. CP brass OH shower head & Shower Arm .

50 One No. CP brass Bath Spout.

Including cutting and making good the walls wherever

52 Shower set as described above. Each 2 11298.45826 22596.92

53 Soil, Waste, Vent & Rain Water Pipes

Providing and laying cement concrete in 1:2:4 (

54 4.1.3 1cement : 2 Coarse sand : 4 graded stone aggregate Cum 0.5 7878.5 3939.25

20 mm nominal size ) and curing complete, including

cost of form work.

Providing and fixing to the inlet mouth of rain water

56 12.44 pipe cast iron grating 15 cm diameter and weighing not Each 5 54.7 273.5

less than 440 grams.

Providing and fixing Centrifugally cast (spun) iron

57 17.4 socket & spigot (S&S) pipe as per IS: 3989 soil, waste

and vent pipes .

Providing and fixing bend of required degree with

access door, insertion rubber washer 3 mm thick, bolts

and nuts complete. Sand cast iron S&S as per IS -

Providing and fixing plain bend of required degree Sand

cast iron S&S as per IS - 3989.

65 DSR-17.40Providing and fixing heel rest sanitary bend.

67 17.40.1.2Sand cast iron S&S as per IS - 3989 Each 8 548.7 4389.6

Providing and fixing double equal plain junction of

required degree.

70 17.42.1.2Sand cast iron S&S as per IS - 3989 Each 5 1075.05 5375.25

Providing and fixing single equal plain junction of

71 17.43 required degree with access door, insertion rubber

washer 3 mm thick, bolts and nuts complete.

73 17.43.1.2Sand cast iron S&S as per IS - 3989 Each 15 925.7 13885.5

Providing and fixing single equal plain junction of

required degree.

76 17.44.1.2Sand cast iron S&S as per IS - 3989 Each 15 811.9 12178.5

78 17.44.2.2Sand cast iron S&S as per IS - 3989 Each 12 561.2 6734.4

Providing and fixing single unequal plain junction of

required degree.

81 17.48.1.2Sand cast iron S&S as per IS - 3989 Each 12 1032.4 12388.8

Providing and fixing terminal guard.Sand cast iron S&S

as per IS - 3989.

Providing and fixing collar.Sand cast iron S&S as per IS

Providing lead caulked joints to sand cast

88 17.6 iron/centrifugally cast (spun) iron pipes and fittings of

Digitally signed by JAYA

1 Sanitary Installations & Internal Water Supply UNITS QUANTITY RATES DSR AMOUNT NSOR AMOUNT

Providing and fixing MS Stay clamps for sand cast iron/

92 17.59 centrifugally cast (spun) iron pipes of diameter.

Providing and fixing trap of self cleansing design with

95 17.60 screwed down or hinged with or without vent arm

complete, including cost of cutting and making good

the walls and floors.

96 17.60.1 100 mm inlet and 100 mm outlet

97 17.60.1.1Sand cast iron S&S as per IS - 3989 Each 15 1996.5 29947.5

Painting sand cast iron/ centrifugally cast (spun) soil,

waste, vent pipes and fittings with paint of any colour

98 17.65 such as chocolate grey, or buff etc. over a coat of

primer (of approved quality) for new work.

99 17.65.1 100 mm diameter pipe Metre 120 82.8 9936

100 17.65.2 75 mm diameter pipe Metre 50 62.95 3147.5

Providing and fixing uPVC agricultural pipes

conforming to IS:4985 (6 kg/sqcm) including all

104 fittings, e.g. couplings, tees, bends, reducers and

screwed adoptors jointing with solvent cement joint as

per manufacturers' recommendations. [for Rain Water

Providing and fixing of GI split pipe support clamps with

EPDM rubber lining, Zinc plated for support of

vertical/hanging horizontal soil, waste, vent and rain

108 water pipes, embedded in walls with anchor fastner,

including recommended size GI threaded rod of

required length etc. including cost of cutting holes and

making good the walls complete in all respects.

109 NS-69 For 75 mm dia Pipe (Thickness of clamp 1.7 mm) Each 24 375.1940857 9004.66

NS-70 For 100 mm dia Pipe (Thickness of clamp 2.0 mm)

NS-71 For 150 mm dia Pipe (Thickness of clamp 2.0 mm)

Providing and fixing cast brass floor clean out plug with

suitable insert keys for opening, male threaded joint

112 with GI threaded socket drip seal to soil / waste pipe of

CI pipe as required complete as per drawing approved

sample and direction of engineer in charge.

NS-73 Providing and fixing in position 100x50 mm dia GI

115 reducing elbow including fix to floor with cement Each 12 1869.879616 22438.56

NS-74 Providing and fixing 100 mm dia. GI inlet fitting/

116 Extension Piece with 2 or 3 inlets of 32 to 50 mm dia, Each 12 2022.149943 24265.80

fixed to CI trap with Drip Seal joint and set in cement

concrete as per drawing complete.

118 Water Supply

Providing and fixing Chlorinated Polyvinyl Chloride

(CPVC) pipes, having thermal stability for hot & cold

water supply including all CPVC plain & brass threaded

119 18.7 fittings i/c fixing the pipe with clamps at 1.00 m

spacing. This includes jointing of pipes & fittings with

one step CPVC solvent cement and testing of joints

complete as per direction of Engineer in Charge.

120 Internal Work - Exposed on Wall

121 18.7.5 40 mm nominal outer dia .Pipes. Metre 1 702.95 702.95

Providing and fixing Chlorinated Polyvinyl Chloride

(CPVC) pipes, having thermal stability for hot & cold

water supply including all CPVC plain & brass threaded

fittings i/c fixing the pipe with clamps at 1.00 m

122 18.8 spacing. This includes jointing of pipes & fittings with

one step CPVC solvent cement and the cost of cutting

chases and making good the same including testing of

joints complete as per direction of Engineer in Charge.

Concealed work including cutting chases and making

good the walls etc.

124 18.8.2 20 mm nominal outer dia .Pipes. Metre 255 537.6 137088

125 18.8.3 25 mm nominal outer dia .Pipes. Metre 100 627.25 62725

126 18.8.4 32 mm nominal outer dia .Pipes. Metre 35 739.3 25875.5

Providing and fixing G.I. pipes complete with G.I.

127 18.10 fittings and clamps, i/c cutting and making good the

128 Internal work - Exposed on Wall

129 18.10.2 20 mm dia nominal bore Metre 10 437.3 4373

130 18.10.3 25 mm dia nominal bore Metre 10 551.7 5517

131 18.10.4 32 mm dia nominal bore Metre 6 667 4002

132 18.10.5 40 mm dia nominal bore Metre 25 811.9 20297.5

133 18.10.6 50 mm dia nominal bore Metre 70 1048.35 73384.5

134 18.8.5 65 mm dia nominal bore Metre 60 1076 64560

135 18.8.6 80 mm dia nominal bore Metre 90 1252 112680

Painting G.I. pipes and fittings with synthetic enamel

136 18.38 white paint with two coats over a ready mixed priming

137 18.38.2 20 mm dia nominal bore Metre 10 23.25 232.5

Digitally signed by JAYA

1 Sanitary Installations & Internal Water Supply UNITS QUANTITY RATES DSR AMOUNT NSOR AMOUNT

138 18.38.3 25 mm dia nominal bore Metre 10 30.25 302.5

139 18.38.4 32 mm dia nominal bore Metre 6 36.35 218.1

140 18.38.5 40 mm dia nominal bore Metre 25 42.65 1066.25

141 18.38.6 50 mm dia nominal bore Metre 70 51 3570

142 NS-180 65 mm dia. nominal bore Metre 60 70.65343173 4239.21

143 NS-181 80 mm dia. nominal bore Metre 90 97.45300928 8770.77

Providing and fixing G.I. Union in G.I. pipe including

144 18.46 cutting and threading the pipe and making long screws

145 18.46.2 20 mm dia nominal bore Each 15 346.8 5202

146 18.46.3 25 mm dia nominal bore Each 1 439.25 439.25

147 18.46.4 32 mm dia nominal bore Each 4 489.05 1956.2

148 18.46.5 40 mm dia nominal bore Each 8 631.3 5050.4

149 18.46.6 50 mm dia nominal bore Each 1 823.8 823.8

150 18.46.7 65 mm dia. nominal bore Each 5 1136.8 5684

151 18.46.8 80 mm dia. nominal bore Each 5 1207.95 6039.75

Providing and placing on terrace (at all floor levels)

polyethylene water storage tank, IS : 12701 marked,

152 18.48 with cover and suitable locking arrangement and Litre 5000 11 55000

making necessary holes for inlet, outlet and overflow

pipes but without fittings and the base support for tank.

Cutting holes up to 15x15 cm in R.C.C. floors and roofs

for passing drain pipe etc. and repairing the hole after

insertion of drain pipe etc. with cement concrete 1:2:4

153 18.77 (1 cement : 2 coarse sand : 4 graded stone aggregate Each 14 452 6328

20 mm nominal size), including finishing complete so

as to make it leak proof.

Supplying, fixing, testing and commissioning of

butterfly valve of PN 1.6 rating with bronze/gunmetal

154 18.11 seat duly ISI

marked complete with nuts, bolts, washers, gaskets

conforming to IS 13095 of following sizes as required.

Providing and fixing forged brass ball valve of brass

body with hard chrome plated steel ball inside PTFE

157 (Teflon) seat & ring with chrome plated centre handle

with female BSP threads complete in all respects.

158 NS-75 20 mm nominal bore Each 25 587.2263632 14680.66

159 NS-76 25 mm nominal bore Each 6 930.5821079 5583.49

160 NS-77 32 mm nominal bore Each 10 1554.785244 15547.85

161 NS-78 40 mm nominal bore Each 4 2264.387116 9057.55

162 NS-79 50 mm nominal bore Each 4 3250.434382 13001.74

Digitally signed by JAYA

Construction of Regional office Building at Khurdha (Odisha)

1.0 DSR SUB HEAD-I :-WIRING POINTS UNIT QUANTITY RATES DSR AMOUNT NSOR AMOUNT

(A) Wiring Points in Surface Conduit with PVC

insulated 1100 V grade cable

Wiring point for light with 1.5 sq. mm.FRLSH PVC

insulated multistrand single core copper conductor

cable in heavy guage rigid steel conduit pipe on

surface, complete with 14 SWG copper earth

continuity wire, GP Box ,modular type switch and

ceiling rose/angle/ batten holder on 3 mm. thick

phenolic laminated backelite sheet etc. complete in

all respect, as directed.

Wiring points for two ways light with 1.5 sq.

mm.FRLSH PVC insulated multistrand single core

copper conductor cable in heavy guage rigid steel

conduit pipe on surface, complete with 14 SWG

copper earth continuity wire, GP Box , two ways 2

nos. modular type switches & ceiling rose/

angle/ batten holder on 3mm. thick phenolic

backelite sheet etc., complete in all respect, as

Wiring point for fan /fresh air fan (light duty exhaust

fan) with 1.5 sq.mm.FRLSH PVC insulated

multistrand single core copper conductor cable in

heavy guage rigid steel conduit pipe on surface

complete with 14 SWG copper earth continuity wire,

piano type switch & ceiling rose on

3 mm. thick phenolic laminated backelite sheet etc,

complete in all respect.

Wiring point for call bell with 1.5 sq. mm.FRLSH PVC

insulated multistrand single core copper conductor

heavy guage rigid steel conduit pipe on surface,

with 14 SWG copper earth continuity wire ,GP Box ,

piano type bell push or 2 pin socket etc. complete in

Wiring point for exhaust fan with 1.5 sq. mm.FRLSH

PVC insulated multistrand single core copper

conductor cable in heavy guage rigid steel conduit

1.5 1.15.0 pipe on surface complete with14 SWG copper earth

continuity wire, 15 A piano type switch & ceiling rose

on 3 mm.thick phenolic laminated backelite sheet

etc, complete in all respect.

(B) Laying of conduit pipes in wall for total

concealed light fan, plug points and for

concealed sub mains

Supply and fixing of 6 SWG GI wire on surface or in

recessed for loop earthing as required

Wiring for light/ power plug with 2X4 sq. mm FRLS

PVC insulated copper conductor single core cable in

1.7 1.12 surface/ recessed steel conduit alongwith 1 No 4 sq. Meter 800 355.042 284033.60

mm FRLS PVC insulated copper conductor single core

cable for loop earthing as required.

Supplying and drawing 2 pair 0.5 mm dia FRLS PVC

insulated annealed copper conductor, unarmored

telephone cable in the existing surface/ recessed

steel/ PVC conduit as required.

Supplying and drawing co-axial TV cable RG-6 grade,

0.7 mm solid copper conductor PE insulated, shielded

1.9 1.19 with fine tinned copper braid and protected with PVC Meter 200 49.961 9992.20

sheath in the existing surface/ recessed steel/ PVC

conduit as required.

2.0 SUB HEAD-II :-SUB MAINS

Wiring of Submains with copper cable in

existing steel conduit as requirred-

3.0 SUB HEAD-III :-EARTHING SYSTEM

Digitally signed by JAYA

1.0 DSR SUB HEAD-I :-WIRING POINTS UNIT QUANTITY RATES DSR AMOUNT NSOR AMOUNT

Earthing with copper earth plate 600mm x 600mm x

3mm at least 2.7 metres below ground level

complete charcoal/coke and salt at least 150mm

thick alround etc. complete in all respect.

Earthing with GI earth plate 600mm x 600mm x

6mm at least 2.7 metres below ground level

complete charcoal/coke and salt at least 150mm

thick alround etc. complete in all respect.

Providing and fixing earth bus of 50 mm X 5 mm

3.4 5.20 copper strip on surface for connections etc. as Meter 60 2246.119 134767.14

Supply and laying of 25mm x 5 mm G.I. strip from

3.5 5.15 earth electrode directly in the ground as required Meter 150 259.372 38905.80

complete in all respect.

Providing and fixing 6 SWG dia G.I. wire on surface or

in recess for loop earthing along with existing

surface/ recessed conduit/ submain wiring/ cable as

4.0 SUB HEAD-IV :-MINIATURE CIRCUIT BREAKER

S&F and making connection of 40A 2 pole 30mA

ELCB/RCCB of Din Rail Mounting complete in all

respect as per direction and satisfaction to the

Engineer in charge.

4.2 2.10.1 S&F of 6 Amp to 32 Amp. MCB (10 KA) C Curve

Single Pole Each 170 272.128 46261.76

4.3 2.13.1 S&F of 40 Amp. 4 pole Isolator (10 KA) C Curve

S & F surface/Flush mounting 8 ways SPN distribution

board with additional metal door without MCB

complete in all respect, as Direct by Engineer in

2.3.2 8 Way double door Each 4 2735.099 10940.40

S & F surface/Flush mounting 8ways TPN distribution

board with additional metal door without MCB

complete in all respect, as directed at site by

Engineer in charge.

supplying and fiing folloing rating,double

pole,240v,isolator in the exiting MCB DB complete

with connectoin testing and commissioning etc.as

supplying and fiing folloing rating,double

pole,240v,residual current circuit breaker

2.14 (RCCB),having a enitivity currrent 30ma in the eiting

MCB DB completed with connection ,teting

commisoining etc.as required.

5.0 SUB HEAD-V :-MISCELLANEOUS ITEMS

Supply, Installation, Testing and Commissioning of

1200 mm sweep,BEE 5 star rated, ceiling fan with

Brush Less Direct Current (BLDC)Motor, class of

insulation: B, 3 nos. blades, 30 cm long down rod,

2nos. canopies, shackle kit, safety rope, copper

winding, Power Factornot less than 0.9, Service Value

(CM/M/W) minimum 6.00, Air delivery minimum 210

5.1 19.1 Cum/Min , 350 RPM (tolerance as per IS : 374- Each 15 2901.99 43529.85

2019),THD less than 10%, remote or electronic

regulator unit for speed control and all remaining

accessories including safety pin, nut bolts,washers,

temperature rise=75 degree C (max.), insulation

resistance more than 2 mega ohm, suitable for 230

V, 50 Hz, single phase AC Supply, earthing etc.

complete as required.

Supply and fixing of shock treatment chart

(prescribed under I.E. rules)(50 x 70 cm)

Supply and laying of 2000mm x 1000mm x 3mm

thick chequered rubber matting of tested quality.

Supply and fixing of power plug with 15A/16A, 250

volt flush type switch a

Supply and fixing of power plug with 6A, 250 volt

flush type switch a

6.0 SUB HEAD-VI :-LUMINAIRES WORK

Supply of following sizes of heavy duty exhaust fan

for single phase 230 volt, 50HZ AC supply complete

with motor, blades, frame, bracket, louver/ shutter

etc as required.

a 250 mm Exhaust Fan (1200 RPM) Nos 8 1865.875 14927.00

Digitally signed by JAYA

1.0 DSR SUB HEAD-I :-WIRING POINTS UNIT QUANTITY RATES DSR AMOUNT NSOR AMOUNT

Supply, Installation, Testing & Commissioning of

6.2 NS-7 recessed type down lighter complete with lamps & Each 80 1381.53456 110522.76

accessories 18 W LED

Supply, Installation, Testing & Commissioning of

6.3 NS-8 surface mounted type down lighter complete with Each 10 1122.49683 11224.97

lamps & accessories 18W LED

Supply, Installation, Testing & Commissioning of

6.4 NS-9 recess type 2x2, 24 watt LED Light Fixtures complete Each 40 5698.83006 227953.20

with lamps & accessories.

Supply, installation, testing & commisioning of

Recess Linear Connected/Standalone luminaire. Well

6.5 NS-10 designed extruded aluminium housing linear profile Each 80 6216.90552 497352.44

with flushed diuser for perfect optic controls 20W

7.0 SUB HEAD-VII :-CABLE TRAY WORKS

Supplying and installing following size of perforated

Hot Dipped Galvanised Iron cable tray (Galvanisation

thickness not less than 50 microns) with perforation

7.1 4.6 not more than 17.5%, in convenient sections, joined

with connectors, suspended from the ceiling with G.I.

suspenders including G.I. bolts & nuts, etc. as

b 4.6.2 150 mm width X 50 mm depth X 1.6 mm thickness Metre 30 761.108 22833.24

c 4.6.4 300 mm width X 50 mm depth X 1.6 mm thickness Metre 10 1023.669 10236.69

Supplying and installing following size of perforated

Hot Dipped Galvanised Iron cable tray "bends"

(galvanisation not less than 50 microns) with

7.2 4.7 perforation not more than 17.5%, in convenient

sections, joined with connectors, suspended from the

ceiling with G.I. suspenders including G.I. bolts &

nuts, etc. as required.

b 4.7.2 150 mm width X 50 mm depth X 1.6 mm thickness Meter 8 1350.01 10800.08

c 4.7.4 300 mm width X 50 mm depth X 1.6 mm thickness Meter 8 1968.676 15749.41

Supplying and installing following size of perforated

Hot Dipped Galvanised Iron cable tray "Tee"

(galvanisation not less than 50 microns) with

7.30 perforation not more than 17.5%, in convenient

sections, joined with connectors, suspended from the

ceiling with G.I. suspenders including G.I. bolts &

nuts, etc. as required.

b 4.8.2 150 mm width X 50 mm depth X 1.6 mm thickness Meter 8 1470.129 11761.03

c 4.8.4 300 mm width X 50 mm depth X 1.6 mm thickness Meter 8 2291.828 18334.62

Supplying and installing following size of perforated

Hot Dipped Galvanised Iron cable tray "Cross

member"(galvanisation not less than 50 microns)

7.4 4.9 with perforation not more than 17.5%, in convenient

sections, joined with connectors, suspended from the

ceiling with G.I. suspenders including G.I. bolts &

nuts, etc as required.

b 4.9.2 150 mm width X 50 mm depth X 1.6 mm thickness Meter 4 1470.129 5880.52

c 4.9.4 300 mm width X 50 mm depth X 1.6 mm thickness Meter 4 2515.058 10060.23

Supplying and installing following size of perforated

Hot Dipped Galvanised Iron cable tray "Reducer"

(galvanisation not less than 50 microns) with

7.5 4.10 perforation not more than17.5%, in convenient

sections, joined with connectors, suspended from the

ceiling with G.I. suspenders including G.I. bolts &

nuts, etc as required.

b 4.10.2 150 mm width X 50 mm depth X 1.6 mm thickness Meter 2 2042.023 4084.05

c 4.10.4 300 mm width X 50 mm depth X 1.6 mm thickness Meter 2 3000.849 6001.70

Supply & fixing of following size (GP RACEWAY-

Fabricated from GP Sheet) race ways for electrical

& LV wiring including neoprene gasket in joints,

cutting the floor & jaming the race way / hanging in

7.6 ceiling, supporting arrangement as approved by

consultant / architect with all necssary hard ware

(including civil work) as per site requirement. The

thickness of raceway & cover shall be as per technical

Digitally signed by JAYA

1.0 DSR SUB HEAD-I :-WIRING POINTS UNIT QUANTITY RATES DSR AMOUNT NSOR AMOUNT

Supply & fixing of following size of Raceway Junction

Box made out of GP Sheet for electrical & LV wiring

including, cutting the floor & jaming the junction box

/ hanging in ceiling, supporting arrangement as

7.7 approved by consultant / architect with all necssary

hard ware (including civil work).(Junction box to be

provided as per drawing/ as per site requirement &

as per specification). The thickness of junction box

shall be a as per thechnical specification.

a NS-14 150 mm wide x 50 mm deep. Set 10 345.38364 3453.84

b NS-15 200 mm wide x 50 mm deep. Set 8 547.816829 4382.53

b NS-16 300 mm wide x 50 mm deep. Set 8 829.880135 6639.04

8.0 SUB HEAD-VIII :- UPS

Supply, installation, testing & commissioing of 15

KVA UPS at 0.99 input power factor with SNMP card,

compatible for BMS connectivity on

backnet/MODBUS, inbuilt / external isolation

transformer as per specification given in the

document with following broad features.

THD(i) shall be less than 3% in the entire loading

Input power factor shall be more than 0.95. from

25% to 100% load.

UPS shall carry design output at 40 deg.

Shall have soft start and hold of for incoming supply.

Invertor capability to supply 150% load for 5 sec.

Three Phase Input and Three Phase Output. ( Input -

340V - 470V, Three Phase, 4 wire. / Output - 400-

415 Volt, Three Phase, 4 Wire.)

Shall not allow deep discharge of the battery and

shall not go to 10.5 volts in case of 12 volt cells.

Battery shall be external type with rack and suitable

for 30 minute backup on 100% load.

UPS described as above Set 1 369128.7653 369128.77

9.0 SUB HEAD-IX :-DISTRIBUTION CABLE WORKS

Supply and drawing of following size of FRLS PVC

9.1 1.17 insulated copper conductor, single core cable in the

existing surface / recessed steel / PVC conduit as

Supply and making end termination with brass

compression gland and aluminium lugs for following

9.2 9.1 size of PVC Insulated & PVC sheath /XLPE Al

conductor cable of 1.1 kv grade as required-

Supplying and fixing cable route marker with 10 cm X

10 cm X 5 mm thick G.I. plate with inscription there

9.3 7.1 on, bolted /welded to 35 mm X 35 mm X 6 mm angle Each 4 271.065 1084.26

iron, 60 cm long and fixing the same in ground as

10.0 L.T. SWITCH PANEL BOARDS

10.1 NS-18 MAIN DISTRIBUTION BOARD ( MDB-01)

Digitally signed by JAYA

1.0 DSR SUB HEAD-I :-WIRING POINTS UNIT QUANTITY RATES DSR AMOUNT NSOR AMOUNT

Supply, installation, testing & commissioning of

cubical type LT panel suitable for 415 V, 3 Phase, 4

Wire 50 Hz AC supply system having front surface

area as per G.A Drawing, fabricated in

compartmentalized (preferably) design from CRCA

sheet steel of 2 mm thick for frame work and covers,

3 mm thick for gland, plates i/c cleaning & finishing

complete with 9 tank process for powder coating in

approved shade, having 400 Amp capacity extensible

type 4P Aluminium alloy bus bars of high

conductivity, DMC / SMC bus bar supports, with short

circuit withstand capacity of 31 MVA for 1 Sec.,

bottom base channel of MS section not less than 100

mm X 50 mm x 5 mm thick, fabrication shall be done

in transportable sections entire panel shall have a

common copper earth bar of size 25 mm x 5 mm at

the rear with 2 Nos. earth stud, solid connections

from main bus bar to switch gears with required size

of Al. bus bars and control wiring with sq. mm. PVC

insulated copper conductor S/C cable, cable alleys,

cable gland plates in two half, i/c providing following

switch gears :-

1 No. 250Amp Four Pole Moulded Case Circuit

Breaker of 35 KA (Ics Value) .

250/5A class 1, 5VA CTS 1NO Digital multifunction

1 Set of phase indicating lamps with single pole MCB.

1 Set of Breaker 'ON' & 'OFF' / TRIP indicating lamps.

300 Amp 4P Aluminium busbar with coloured heat

shrinkable sleeve.

Providing and fixting of 1 Nos. 160 Amp 4P MCCB of

25KA (Ics value) with T/M OL&SC Protection.

Providing and fixting of 8 Nos. 40 Amp 4P MCB of

10KA (Ics value)

Panel described as above Set 1 127814.3967 127814.40

10.3 NS-20 HVAC panel

Supply, installation, testing & commissioning of

cubical type LT panel suitable for 415 V, 3 Phase, 4

Wire 50 Hz AC supply system having front surface

area as per G.A Drawing, fabricated in

compartmentalized (preferably) design from CRCA

sheet steel of 2 mm thick for frame work and covers,

3 mm thick for gland, plates i/c cleaning & finishing

complete with 9 tank process for powder coating in

approved shade, having 400 Amp capacity extensible

type 4P Aluminium alloy bus bars of high

conductivity, DMC / SMC bus bar supports, with short

circuit withstand capacity of 31 MVA for 1 Sec.,

bottom base channel of MS section not less than 100

mm X 50 mm x 5 mm thick, fabrication shall be done

in transportable sections entire panel shall have a

common copper earth bar of size 25 mm x 5 mm at

the rear with 2 Nos. earth stud, solid connections

from main bus bar to switch gears with required size

of Al. bus bars and control wiring with sq. mm. PVC

insulated copper conductor S/C cable, cable alleys,

cable gland plates in two half, i/c providing following

switch gears :-

1 No. 160Amp Four Pole Moulded Case Circuit

Breaker of 25 KA (Ics Value) .

160/5A class 1, 5VA CTS 1NO Digital multifunction

1 Set of phase indicating lamps with single pole MCB.

1 Set of Breaker 'ON' & 'OFF' / TRIP indicating lamps.

200 Amp 4P Aluminium busbar with coloured heat

shrinkable sleeve.

Providing and fixting of 6 Nos. 63 Amp 4P MCB of

10KA (Ics value)

Panel described as above Set 1 82690.02417 82690.02

10.4 NS-21 UPS PANEL (SDB-01)

Digitally signed by JAYA

1.0 DSR SUB HEAD-I :-WIRING POINTS UNIT QUANTITY RATES DSR AMOUNT NSOR AMOUNT

Supply, installation, testing & commissioning of

cubical type LT panel suitable for 415 V, 3 Phase, 4

Wire 50 Hz AC supply system having front surface

area as per G.A Drawing, fabricated in

compartmentalized (preferably) design from CRCA

sheet steel of 2 mm thick for frame work and covers,

3 mm thick for gland, plates i/c cleaning & finishing

complete with 9 tank process for powder coating in

approved shade, having 400 Amp capacity extensible

type 4P Aluminium alloy bus bars of high

conductivity, DMC / SMC bus bar supports, with short

circuit withstand capacity of 31 MVA for 1 Sec.,

bottom base channel of MS section not less than 100

mm X 50 mm x 5 mm thick, fabrication shall be done

in transportable sections entire panel shall have a

common copper earth bar of size 25 mm x 5 mm at

the rear with 2 Nos. earth stud, solid connections

from main bus bar to switch gears with required size

of Al. bus bars and control wiring with sq. mm. PVC

insulated copper conductor S/C cable, cable alleys,

cable gland plates in two half, i/c providing following

switch gears :-

1 No. 40Amp Four Pole MCCB of 25 KA (Ics Value)

with Thermal Magnetic release for O/L & S/C

1NO Multi function meter.

1 Set of phase indicating lamps with single pole MCB.

1 Set of Breaker 'ON' & 'OFF/TRIP indicating lamps.

50 Amp 4P Aluminium busbar with coloured heat

shrinkable sleeve.

Providing and fixting of 6 Nos.32 Amp DP MCB of

10KA (Ics value) with Protection.

Panel described as above Set 1 45331.60275 45331.60

11.0 SUB HEAD- LIGHTNING CONDUCTOR

Providing and fixing of Lightning Conductor finial,

made of 25 mm dia 300mm ling, G.I. Tube, having

6.2 single prong at top, with 85 mm dia 6 mm thick G.I. Each 2 518 1036.00

base plate including holes etc.

complete as required.

Providing and fixing G.I. Tape 20mmx3mm thick

6.7 on parapat or surface of the wall for lightning Mtr 100 126 12600.00

conductor complete as required. (for Horizontal Run).

Providing and fixing G.I. Tape 20mmx3mm thick

6.8 on parapat or surface of the wall for lightning Mtr 40 197 7880.00

conductor complete as required. (for Vertical Run).

Earthing with G.I. Earth Pipe 4.5 Meter long ,

40mm dia including accessories, and providing

5.2 massonry enclosure with cover plate having Each 2 6855 13710.00

locking arragement and watering pipe etc. with

charcoal/cock and salt as required.

Supplying and laying 25 mm X 5 mm GI strip at 0.50

meter below ground/surface as strip earth electrode,

including connection/ terminating with nut, bolt,

spring, washer etc. as required (Jointing shall be

done by overlapping and with 2 sets of G.I. nut bolt &

spring washer spaced at 50 mm)

12.0 SUB HEAD- LIGHTNING CONDUCTOR

11 KV SUB-STATION

11KV, H.T. METERING PANEL- (INDOOR TYPE)

Supply, erection, testing and commissioning of

Metring cubicle with 11 KV PTs 11kV/110V, 11 KV

CTs 150/5 5A with trivector meter indoor type as per

local Electricity board, getting approval and

calibration as required by the Department. complete

11 KV COMPACT SUB STATION

Digitally signed by JAYA

1.0 DSR SUB HEAD-I :-WIRING POINTS UNIT QUANTITY RATES DSR AMOUNT NSOR AMOUNT

Supply, installation, testing and commissioning of 11

/ 0.433 KV compact package sub station comprising

2 No. 11 KV 630 A Load break switch breaker as

incomer & 1 No. 200 Amps electrically operated trip

free type SF6 breaker at 47 deg. C ambient as

outgoing with metering & protection for 200 KVA 11 /

0.433 KV Oil filled transformer & LT section consisting

of 2 no.400 Amp 4 P MCCB with 400 amp contactor

as incomings of minimum 36 KA breaking capacity

and 1 No. 250 amps TPN MCCB & 5 No. 40 amps 4 P

MCB as outgoing and arrangement for 65 kVAR

capacitor bank including APFC Relay . All MCCB

above 250 amp shall have Microprocessor based

release unit. Package sub-station shall be complete

as per specification. Both the incomers of LT sections

shall be electrical & mechanical interlocked & all

outgoing feeders of LT sections will have dual source

13.0 SUB HEAD- 125 KVA DG Set

Supplying, installation, testing and commissioning of

silent type DG sets, AMF panel, bus ducting/ cables

from DG sets to essential panel, synchronizing panel

where required, DG set enclosure room sound

insulation/ventilation/smoke exhaust as required, Set 1.00 145000.00 145000.00

earthing of DG set system, control cabling, fuel

tank/piping, DG set exhaust piping/ exhaust chimney

as per CPCB norms, civil works connected with DG

sets including foundation as required

TOTAL SUM 7468620.83

Digitally signed by JAYA

Construction of Regional office Building at Khurdha (Odisha)

DSR DESCRIPTION UNIT QTY. RATE DSR AMT. NSOR AMT.

SUBHEAD OF FIRE FIGHTING SYSTEM

Supplying, installation, testing and

commissioning of electric driven terrace pump

2 18.4 suitable for automatic operation and

consisting of following, complete in all

respects, as required: (Terrace Pump)

Horizontal type, multistage, centrifugal pump

of cast iron body and bronze impeller with

3 a. stainless steel shaft, mechanical seal

conforming to IS : 1520.

Suitable HP squirell cage induction motor

TEFC type suitable for operation on 415 volts,

3 phase, 50 Hz, AC supply with IP55 class of

4 b. protection for enclosure, horiziontal foot

mounted type with Class-'F' insulation,

conforming to IS-325.

M.S. fabricated Common base plate, coupling,

5 c. coupling guard, foundation bolts etc. as

Suitable cement concrete foundation duly

plastered with anti vibration pads.

Providing, laying, testing & commissioning of

'C' class heavy duty MS pipe conforming to IS

3589/IS 1239 including Welding, fittings like

elbows, tees, flanges, tapers, nuts bolts,

8 18.7 gaskets etc. and fixing the pipe on the

wall/ceiling with suitable clamp/support frame

and painting with two or more coats of

synthetic enamel paint of required shade

complete as required :

18.7.1 25 mm dia

18.7.6 80 mm dia

Supplying and fixing single headed internal

hydrant valve with instantaneous

Gunmetal/Stainless Steel coupling of 63 mm

13 18.9 dia with cast iron wheel ISI marked

conforming to IS 5290 (Type -A) with blank

Gunmetal/Stainless Steel cap and chain as

14 18.9.2 Single headed Stainless steel Set 3 6525.757 19577.271

Supplying, fixing, testing and commissioning

of butterfly valve of PN 1.6 rating with

15 18.11 bronze/gunmetal seat duly ISI marked

complete with nuts, bolts, washers, gaskets

conforming to IS 13095 of following sizes as

Providing, installation, testing and

commissioning of non-return valve of

18 18.14 following sizes confirming to IS:5312

complete with rubber gasket, GI bolts,

nuts,washers etc.as required :

Providing, installation, testing and

commissioning of stainless steel Y-strainer

20 18.15 fabricated out of 1.6 mm thick stainless steel,

Grade 304, sheet with 3 mm dia holes with

stainless steel flange.

Digitally signed by JAYA

DSR DESCRIPTION UNIT QTY. RATE DSR AMT. NSOR AMT.

Supplying and fixing 63 mm dia, 15 m long

RRL hose pipe with 63 mm dia male and

22 18.16 female couplings duly bound with GI wire, 0

rivets etc. conforming to IS 636 (type-A) as

Stainless Steel (Grade 304)

Supplying and fixing first-aid Hose Reel with

24 18.17 MS construction spray painted in post office

red, conforming to IS 884 complete with the

following as required.

20 mm nominal internal dia water hose

25 thermoplastic (Textile reinforced) type -2 as

20 mm nominal internal dia gun metal globe

valve & nozzle.

Drum and brackets for fixing the equipmets

Connections from riser with 25 mm dia stop

28 gun metal valve & M.S. Pipe and socket.

Supplying & fixing 63 mm dia gun metal short

branch pipe with 20 mm nominal internal

30 18.18 diameter size nozzle conforming to IS 903

suitable for nstantaneous connection to

interconnect hose pipe coupling as required :

Stainless Steel (Grade 304)

Supplying and fixing of fire brigade

connection of cast iron body with gun metal

male instantaneous inlet couplings complete

32 18.19 with cap and chain as reqd. for suitable dia

MS pipe connection conforming to IS 904 as

2 way - 100 mm dia M.S. Pipe

Supplying and fixing air vessel made of 250

mm dia, 8 mm thick MS sheet, 1200 mm in

height with air release valve on top and

flanged connection to riser, drain

34 18.20 arrangement with 25 mm dia gun metal Set 2 19393.372 38786.744

wheel valve with required accessories,

pressure gauge and paintingwith synthetic

enamel paint of approved shade as required.

Providing & fixing of pressure switch in M.S.

35 18.22 pipe line including connection etc. as Each 3 1643.398 4930.194

Supplying and installing following size of

perforated pre-painted M.S. cable trays with

perforation not more than 17.5%, in

36 4.1 convenient sections, joined with connectors,

suspended from the ceiling with M.S.

suspenders including bolts & nuts, painting

suspenders etc as required.

150 mm width x 50mm depth x 1.6 mm

Digitally signed by JAYA

DSR DESCRIPTION UNIT QTY. RATE DSR AMT. NSOR AMT.

Providing and fixing MS partly glazed double

hung lockable shutter fabricated from MS

section as required with 5 mm thick glass for

fire station complete including stove

enamelled painting of door and frame and

words "Fire Hydrant" written on glass,

38 NS-89 suitable to accommodate 2 Hydrant landing Each 3 6674.656273 20023.96882

valves, 1 fire hose reel, 2 nos.15m long 63

mm dia hose,1-branch pipe, 1no. fire man's

axe, fire extiguishers 2 nos, including suitably

mounted on a raised masonry platform as

required. (Approx.size 1.20 m x 2.1m )

Providing and fixing in position the industrial

40 16.8 type pressure gauges with gun metal / brass Each 6 1271.348 7628.088

valves complete as required

Providing and fixing resilient rubber

neoprene lined single arch vibration

eliminators with unit control suitable for raw

water upto 450C temperature working

pressure 25 kg and test pressure 37.5

43 NS-90 100 mm dia Each 2

Providing and fixing heavy duty PVC

insulated, PVC armoured conductor cables

44 1100 V grade including necessary support

clamps and connection lugs complete in all

Power cable 3 core 16 sq mm aluminium

45 NS-91 Metre 30

conductor armoured cable.

Providing and fixing carbon-di-oxide type fire

extinguishers consisting of pressure tested

single cast cylinder with rotary discharge

valve and high pressure discharge tube of

46 minimum 1 m length, discharge horn,

suspension bracket conforming to IS:15683

finished externally with red enamel paint and

fixed to wall with brackets complete with

internal charge (Halon Free Gas)

Providing and fixing carbon-di-oxide fire

extingushers trolley mounted with all

accessories internal discharge tube,high

48 pressure discharge hose,discharge nozzle, ISI

marked as per IS:2878 finished externally

with red enamel paint. (Halon Free Gas)

Providing and fixing ABC Powder type fire

extinguishers consisting of welded M.S.

cylinderical body, squeeze lever discharge

valve fitted with pressure indicating guage

internal discharge tube 30 cms long high

50 pressure discharge hose, discharge nozzle,

suspension bracket conforming to IS:15683

finished externally with red enamel paint and

fixed to wall with brackets complete with

internal charge. (Halon Free Gas)

Digitally signed by JAYA

DSR DESCRIPTION UNIT QTY. RATE DSR AMT. NSOR AMT.

Design, manufacture, supplying, fixing in

position, testing and commissioning of the

following front operated cubicle type, front

access 2mm thick mild steel sheet, free

standing, dust and vermin proof, switchboard

with IP42 protection with hinged and lockable

doors complete with interconnections, tinned

copper crimping lugs, bonding to earth and

painting, suitable for use at 415 volts, 3

phase 4 wire 50 Hz system and suitable for a

fault level of 25 MVA symmetrical at 415

53 NS-95 MCC for Fire Fighting Pumps at Terrace

a) One 100 amp. TP +NL M.C.C.B. with rotary

handle of breaking capacity 25 KA

b) One-Volt Meter (0-500 V) with selector

57 c) One Set indicating lamps

58 BUS BARS OUTGOING

59 a) 100 Amp TPN BUS BAR (Aluminium).

b) One - 63 Amp.TP +NL M.C.C.B. with rotary

handle of breaking capacity 35KA

c) One Fully Automatic D.O.L Starter suitable

for Jockey Pump Motor 15 KW with over load

61 relay, timer push buttons and

Auto/Manual selector switch

d) One panel type Amp. meters one for each

motor with ASS. CTS etc.

e) One sets of On/Off - neon indicating lamp.

i) All interconnecting power & control

wires/cables suitable size within the panel

and from panel to motors , pressure

64 switches, level switches, cable Tray, pipes Set 1 52843.69692 52843.69692

etc. including brass glands termination

within fire pump house and earthing as per

specifications.

ALL SUB-HEAD TOTAL 5,66,162 134376.9363

GRAND TOTAL 700539.24

GRAND TOTAL 700539.24

FIRE ALARM SYSTEM

Supplying, installation, testing&

commissioning of main control and indicating

panel made outof16SWG MS sheet to

accommodate thefollowing items duly powder

coated in approved colour with louvers for

ventilation, locking arrangement, audio and

indication for fire alarm and public address

system, monitoring System including

connections, interconnections etc complete as

reouired.10 ZONE Panel for fire alarm system

250 Watt amplifier racks suitable for

operation on 230VAC/24V DC supply

conforming to IEC-268-3 complete with all

accessories as required -2 Nos.(one toactas

standby) Talk back master station with LED

PTT (press to talk) push button foroperation

on 230VAC/24V DC supply conforming toIEC-

268for simplex mode of operation/

communication suitable for 20 Nos.talk

backunit -1 Annoucement control desk

suitable for selection of different zones

selectively and ON ALL CALL switch with

visual indication etc.complete as required -1

set, Amplifier changeoverswitch forinter

changing amplifier -1 No, Monitor panel for

Digitally signed by JAYA

DSR DESCRIPTION UNIT QTY. RATE DSR AMT. NSOR AMT.

Supplying, installation, testing&

commissioning of smoke detector with builtin

LED and mounting base complete with all

connections etc. as required.

DSR- Supplying, installation, testing &

3 2022- commisssioning of sounder complete as Each 2 2651 5302.00

17.2.6 required.

Supplying, installation, testing &

DSR- commissioning of exit point directional sound

4 2022- speaker with voice and integral audio Each 2 10145 20290.00

17.3.8 amplifier with selectable sound pulse patterns

complete as required

Supplying and drawing of cable Fire Retardant

PVC insulated copper conductor cable in the

existing surface/ recessed steel conduit of

following pairs, cores and size including

connections and interconnections etc. as

5.1 speaker cable Two pair, 2-core, 1.5 sqmm Mtr 200 89 17800.00

DSR- Supplying and fixing 25 mm dia MS flexible

6 2022- pipe with PVC coating along with all ancillaries Mtr 200 53 10600.00

17.5.4 and accessories like coupler etc. as

ALL SUB-HEAD TOTAL 152053.00 0.00

Digitally signed by JAYA

Construction of Regional office Building at Khurdha (Odisha)

1 NS LIFTS UNIT QUANTITY RATES DSR AMOUNT NSOR AMOUNT

Design, manufacture, Supply, Installation,

Testing & Commissioning of 13 passenger

gearless lift electric traction, (MRL) MACHINE

ROOM LESS having contract speed of 1.5 Meter

per second serving different floors as per

detailed specifications attached and as under

complete with all the equipment and

Lift shaft size 1900 mm (Width) x 2500 mm

(Depth) and 1600 mm pit depth.

1.3 Floors - G + 1

Stop & Opening - 02 Stop & 02 Opening (all

opening be on same side)

Controller - V3F (Variable Voltage Variable

Automatic Rescue Device (ARD) complete with

dry maintenance free batteries as required.

1.7 Operation - Microprocessor based Duplex control

Power: 415 Volts ± 10%, 3 Phase 4 wire 50 Hz

1.9 Car Enclosure: Stainless steel (Hairline Finish)

1.10 Car doors: Stainless steel (Hairline Finish)

1.11 Landing doors: Stainless steel (Hairline Finish)

Car entrance door opening arrangement: CO

(Center Opening Doors)

1.13 Handrail on rear wall of car in SS hairline Finish

1.14 Full length Mirror on rear wall of car

Lifts should be with following: Voice

announcement system, Car Arrival Chime, DC

alarm bell, Multi beam sensor, Safety landing

operation, Next landing operation, Independent

operation, Hand operation (slow speed

maintenance operation), Braille Buttons,

Emergency stop button, Emergency cabin

lighting, Emergency interphone system

incorporated on cabin operating panel, Re-open

1.15 with hall call button operation, Automatic door

open time adjustment operation, Car call

registered light, Hall call registered light,

Emergency Exit, Ventilation Fan, Overload

Indicator, Attendant Service, Emergency

Landing Device, flat cable with camera and

internal intercom. Car operating panel and car

position indicator face plates finish: LED

Indicator Provided in stainless steel hairline

TOTAL AMOUNT OF PASSENGERS AS

TOTAL AMOUNT OF PASSENGERS AS

DESCRIBED ABOVE

Digitally signed by JAYA

1 NS LIFTS UNIT QUANTITY RATES DSR AMOUNT NSOR AMOUNT

2.0 NS LIFT PANEL

Supply, installation, testing & commissioning

of cubical type LT panel suitable for 415 V, 3

Phase, 4 Wire 50 Hz AC supply system having

front surface area as per G.A Drawing,

fabricated in compartmentalized (preferably)

design from CRCA sheet steel of 2 mm thick for

frame work and covers, 3 mm thick for gland,

plates i/c cleaning & finishing complete with 9

tank process for powder coating in approved

shade, having 125Amp capacity extensible type

4P Aluminium alloy bus bars of high

conductivity, DMC / SMC bus bar supports, with

short circuit withstand capacity of 31 MVA for 1

Sec., bottom base channel of MS section not

less than 100 mm X 50 mm x 5 mm thick,

fabrication shall be done in transportable

sections entire panel shall have a common

copper earth bar of size 25 mm x 5 mm at the

rear with 2 Nos. earth stud, solid connections

from main bus bar to switch gears with required

size of Al. bus bars and control wiring with sq.

mm. PVC insulated copper conductor S/C cable,

cable alleys, cable gland plates in two half, i/c

providing following switch gears :-

1 No. 40 Amp 4P MCB with following accessories-

1 Set of phase indicating lamps with Single Pole

1 Set of ON / OFF indicating lamps with Single

50 Amp 4P Aluminium busbar with coloured heat

shrinkable sleeve.

i) 4 Nos. 25 Amp 4P Miniature Circuit Breaker.

iii) 1 Nos. 25 Amp DP Miniature Circuit Breaker.

Panel described as above Set 1 25903.773 25903.77

ALL SUB-HEAD TOTAL 12,61,739.20

Digitally signed by JAYA

Construction of Regional office Building at Khurdha (Odisha)

A STRUCTURED CABLING SYSTEM PASSIVE UNIT QUANTITY RATES NSOR AMOUNT

Supply, installation, testing & commissioning of

armoured 6 core Singlemode OS2 (9/125 Micro),

Corrugated ECCS Armor, HDPE (UV) Sheathing,

Theoxtropic gel filled OFC cable with 2 Nos steel

music wire embedded in side sheathing as stregth

1 NS-30 member for switch connectivity. Cable should be Mtr 300 98.68 29604.31

ROHS compliant and as per IEC60749-1 with

product warranty of 30 years.

Supply, installation, testing & commissioning of

6F SM loaded LIU with LC adaptor plates, pigtel

cables, Spilce tray, cable holder and 4 nos of cable

entry exist point with rubber gurment along with

the LIU, Powder Coaded 1.2mm steel sheet metal,

1U etc complete as required. LIU should be in

accordance with YD/T 778-2006 Optical

Distribution Frame & YD/T 1272.1-2003 Optical

Fiber Connector Part 1: Type LC and should have

30 years of product warranty.

Supply, installation, testing & commissioning of

24F SM loaded LIU with LC adaptor plates, pigtel

cables, Spilce tray, cable holder and 4 nos of cable

entry exist point with rubber gurment along with

the LIU, Powder Coaded 1.2mm steel sheet metal,

1U etc complete as required. LIU should be in

accordance with YD/T 778-2006 Optical

Distribution Frame & YD/T 1272.1-2003 Optical

Fiber Connector Part 1: Type LC and should have

30 years of product warranty.

Supply, installation, testing & commissioning of

LC-LC singlemode OS2 (9/125) duplex, LSZH fiber

patch cord for LIU to switch connectivity. Patch

4 NS-33 Cord should have aramid yarn as strenght member Nos. 12 2173.18 26078.11

with 1000 time mating cycle.

Supply, installation, testing & commissioning of

CAT 6A UTP LSZH Cable, 23 AWG solid copper

conductors in accordance to TIA/EIA 568 C.2

(Category 6a) & ISO/IEC 11801 2nd ed(Class Ea),

UL Approved, tested @500 Mhz, with HDPE

5 NS-34 insulation of individual conductor and over all Dia Mtr 2000 57.02 114031.42

of 7.2 mm for Connectivity of Hub room to End

Point. Grey Color

Supply, installation, testing & commissioning of

CAT 6A UTP Universal (both tool & toolless)

information outlet (I/O) in accordance with ANSI

TIA 568 C.2, IEC 60603-7-4 2nd Edition, ISO/IEC

TR 11801-9901-2014, ROHS Compliant. The I/O

6 NS-35 should have minimum 750 mating cycle and 200 Nos. 80 356.35 28507.86

insertion cycle and UL approved,for Data, Voice, &

Wi-Fi at user end.

Supply, installation, testing & commissioning of

loaded 24 port CAT 6A UTP, Transparent shutter

jack panel, 1U height, UL-94V-0, Black with cable

7 NS-36 support bar, clear label marks and earthing plug Nos. 7 10964.56 76751.92

for CAT6A cable termination at rack end.

Digitally signed by JAYA

A STRUCTURED CABLING SYSTEM PASSIVE UNIT QUANTITY RATES NSOR AMOUNT

Supply, installation, testing & commissioning of

CAT 6A UTP, LSZH Patch Cord as per

ANSI/TIA/EIA 568C.2 and UL 94-V-0, ROHS

8 NS-37 Compliant, patch cord 1 Mtr for rack side switch to Nos. 80 356.35 28507.86

jack panel connectivity.

Supply, installation, testing & commissioning of

CAT 6A UTP, LSZH Patch Cord as per

ANSI/TIA/EIA 568C.2 and UL 94-V-0, ROHS

9 NS-38 Compliant, patch cord 2 Mtr for rack side switch to Nos. 80 383.76 30700.77

end user connectivity.

Supply, installation, testing & commissioning of 1,

2 and 4 port face plate, British Style with Shutter,

2 Plate system clear finish with transparent

labelling, ABS-UL94-V2, ROHS Compliant, in

accorandce with standards like ANSI/TIA-568-C.2,

2009 & ISO/IEC 60603-7 white for I/O fixing at

Supply, installation, testing & commissioning of

36 U (600W/1000D) floor mount rack with fans , 2

11 NS-40 cable managers , satationary shelf , 2 Nos. of Nos. 1 34538.36 34538.36

12 SECTION - II- IP-PBX SYSTEM 0.00

Supply, installation, testing & commissioning of

Pure IP at core server Based voice solution with

04 Port Voicemail ,04 Port FXS ,04 Port FXO ,1 PRI

Trunk lines (30 Ch) Circuit with CLIP Facility ,50 IP

users License ,01 Nos. IP Operator Console, 100

13 NS-41 Party Conference ,Speed Dial, Music on Hold , Set. 1 575639.40 575639.40

Internal/ External ring difference ,Call Barring, Call

Pickup, TEC should be with GR Number, - Should

Support Redundant server in active-Active mode.

Supply, installation, testing & commissioning of

Type 1 IP Phone 1 VoIP account , Full duplex

14 NS-42 speaker phone, IPV6, 2xLAN, PoE . Nos. 20 7565.55 151310.93

SECTION - III- LOCAL AREA NETWORK ( LAN

Supply, Installation, Testing & Commissioning of

24 Port POE+ Access Switches with switching

capaticy of 128 Gbps, forwarding performance 95

Mpps, minimum PoE budget of 350W, with 2x 10G

SFP+ uplink ports. Should support for Stacking/VC

with stacking bandwidth of maximum 40 Gbps as

and when required. Should support min 2GB

internal DRAM, 2GB internal Flash memory, 16K

16 NS-43 MAC address. Should have Static Routing , Nos. 2 153777.95 307555.91

Neighbor discovery, system logging, Telnet, SSH,

SNMP, Network Time Protocol (NTP), Domain

Name System (DNS) and IPv6 features from day 1

and should support OSPF, VRRP, OSPFv3 and PIM

with 1 year support.

Supply, installation, testing & commissioning of

17 NS-44 fiber Modules 10G BASE Nos. 2 20284.44 40568.87

Digitally signed by JAYA

A STRUCTURED CABLING SYSTEM PASSIVE UNIT QUANTITY RATES NSOR AMOUNT

Supply, installation, testing & commissioning of

Appliance based customised ITAM for asset

inventory management with ability to map

physical locations and exact rack elevations for

audit and support control. Appliance shall be Intel

18 NS-45 x86 based device with secure intranet server with Nos. 1 904576.20 904576.20

Linux Based operating system and relational

databases for long term storage. Appliance

includes license for 100 units under control.

SITC of WirelessIndoor Access Point support Data

rate support 1.8 Gbps , 2.5 Ghz - 2x2 : 2

802.11b/g/n/ac up to 400 Mbps data rate; 2x2 : 2

802.11ax up to 575 Mbps, 5 Ghz - 2x2 : 2

802.11ax up to 1,200 Mbps, Transmit

Beamforming and Maximal Ratio Combining the

WLAN Access Point solution should have integrated

dynamic packet capture, WIPS, detection of

rougue and honeypot Access Point detection, able

19 NS-46 to create WxLAN policies . AP indoor 2x2 with Nos. 4 31249.00 124995.98

802.11 a/b/g/n/ac support. The solution should be

artificial intelligence based self healing solution.

should also support Asset Tracking if required in

future without any change in Hardware. Should

support upto 16 SSIDs per AP. Must be able to

limit per SSID or per user based uplink or

downlink bandwidth.

20 NS-47 SUB-HEAD -IV- IP CCTV SYSTEM

Supply, installation, testing and commissioning of

5 MP Dome camera ,ONVIF profile S,G & T. UL ,

CE , FCC,BIS Certified ,OEM defined MAC

address.1/2.7” Progressive Scan CMOS ,3.6 mm

fixed lens , Quad stream Each stram support

H.265 compression simultaneously ,min

illumination : Color 0.05lux @ F1.2(AGC ON) ;

B/W 0 lux @ IR ON , Shutter speed : 1 / 5s ~ 1 /

100,000 s , WDR , Compression :

H.265/H.265+/H.264/H.264+ .SD card support

upto 256GB , frame rate : Main stream should

support 25/30 fps@5MP, Built in Mic, Edge

21 NS-48 analytics : Customer Flow staistics, Heat Map, Nos. 14 18057.26 252801.64

Human & Vehicle Detection, Pedestrian Intrusion

Detection & Line cross Detection. Queue length

detection Regional population statistics, SOD-

Stationaary Object Detection, Motion Detection,

Tempring Detection, Rare Sound Detection,

License Plate Detection. Defog. Protocols:- TCP/IP,

HTTP, DHCP, DNS, DDNS, RTP/RTSP, SMTP, NTP,

UPnP, SNMP, HTTPS, FTP, P2P, UDP,PPPoE,

Bonjour. In built IR LED , IR Distance upto 30

meters , IP 66 , POE.

Digitally signed by JAYA

A STRUCTURED CABLING SYSTEM PASSIVE UNIT QUANTITY RATES NSOR AMOUNT

Supply, installation, testing and commissioning of

5 MP Bullet camera ,ONVIF profile S,G & T. UL ,

CE , FCC,BIS Certified,OEM defined MAC

address,1/2.7” Progressive Scan CMOS ,3.6 mm

fixed lens , Quad stream Each stram support

H.265 compression simultaneously ,min

illumination : Color 0.05lux @ F1.2(AGC ON) ;

B/W 0 lux @ IR ON , Shutter speed : 1 / 5s ~ 1 /

100,000 s , WDR , Compression :

H.265/H.265+/H.264/H.264+ .SD card support

upto 256GB , frame rate : Main stream should

support 25/30 fps@5MP, Built in Mic, Edge

22 NS-49 analytics : Customer Flow staistics, Heat Map, Nos. 3 16309.78 48929.35

Human & Vehicle Detection, Pedestrian Intrusion

Detection & Line cross Detection. Queue length

detection Regional population statistics, SOD-

Stationaary Object Detection, Motion Detection,

Tempring Detection, Rare Sound Detection,

License Plate Detection. Defog. Protocols:- TCP/IP,

HTTP, DHCP, DNS, DDNS, RTP/RTSP, SMTP, NTP,

UPnP, SNMP, HTTPS, FTP, P2P, UDP,PPPoE,

Bonjour. In built IR LED , IR Distance upto 30

meters , IP 66 , POE.

Supply, installation, testing and commissioning of

32 channel NVR , ONVIF compliant , Certification

CE,FCC,UL,BIS,OEM defined MAC address.

recording bandwidth 320 Mbps , output interface 1

HDMI (up to 4K), 1 VGA , Alarm in/out :16ch in /

4ch out , 1 X RJ-45 port (1000M) , Bit Rate

16kbps-20mbps per channel, Sync Playback

4/8/10/16 ch playback, iOS smartphone support ,

8 HDD support , each HDD slot support upto 8 TB

HDD , , 1x3.0 USB for backup /upgrade , 2x 2.0

USB for mouse, 1 E-Sata Port, Cloud Storage, Net

HDD, Edge analytics : Customer Flow staistics,

23 NS-50 Face Attendence, Face Detection and Recognition, Nos. 1 115127.88 115127.88

Heat Map, Human & Vehicle Detection, Pedestrian

Intrusion Detection & Line cross Detection, Queue

length detection, Regional population statistics,

SOD-Stationaary Object Detection, Deterrence,

PIR, Video tampering, AI Registerd Qty- 10000 &

AI Captured Qty- 200000. Protocol support:-

HTTp, TCP/IP, IPv4, UPNP,

RTSP,UDP,SMTP,NTP,DHCP,DNS,IP

filter,PPPOE,DDNS,FTP,IP search, P2P,

NFS/SMB/CIFS, ONVIF.

Supply, installation, testing & commissioning of

24 NS-51 8TB Surviellance Hard Disk. Nos. 1 18455.20 18455.20

Supply, installation, testing & commissioning of

25 NS-52 Full HD 55" LED Professional Display Panel. Nos. 1 60359.36 60359.36

Supply, installation, testing & commissioning of

Workstation PC: Intel(R) Core(TM) i7-3770

Processor (8M Cache, up to 3.90 GHz); RAM: 8GB

(1x8GB) Non-ECC DDR3 1600MHz ; Keyboard: 12

function keys; Chassis: Tower/Workstation; DVD:

8X Slimline DVD+/-RW, Data Only; Dual Graphics

Card; Network interface card: Integrated Intel(R)

82579LM Gigabit1 Ethernet LAN 10/100/1000;

Hard disk: 250GB, 7200 RPM 3.5" SATA 6Gb/s

Hard Drive; Operating system: Windows 7

Professional 64 Bit or latest.

Total Amount 30,96,934.78

Total Amount 30,96,934.78

Digitally signed by JAYA

Construction of Regional office Building at Khurdha (Odisha)

UNITS QUANTITY RATES DSR AMOUNT NSOR AMOUNT

1 1 Outdoor Unit

Supply Installation,Testing & Commissioning of

modular type Variable Refrigerant Flow / Variable

Refrigerant Volume air cooled Outdoor unit ssuitable

for cooling and heating ,having all hermetically seale

dinverter type Scroll Compress or (s) ,minimum two

compressors for above 14HP modules, microprocessor

based Controller ,top discharge type condensing unit

(s) ,with R410A Refrigerant, vibrationisolators, with

suitable foundation etc.complete as required. The unit

shall deliver the rated capacity at AHRI Condition

sandwork evenat 50°C ambient temperature with

outtripping. The unit shall be suitable to work on

400V+/-10%,3 Phase ,50 Hz AC power supply.The unit

shall be filled with first charge of the refrigerantand

ready for use as required.The COP at AHRI conditions

shall not be less than 3.1 and IEER not less than 6.5 .

Indoor VRF Units (Nominal Capacity) - Ceiling

Mounted Round/4way flow cassette type Unit

Supply,installation ,testing and commissioning of

following minimum capacity4-way flow VRV

/VRFCassetteType Indoor ceiling mounted unit

equipped with synthetic wash ablemediapre-filter,fan

section with low noise fan /dynamically balanced

blower,multi speed motor,coil section with DX Copper

coil, electronic expansion valve,outer cabinet ,drain

6 pump,grill,necessary supports,vibration

isolation,cordless remote controletc.,suitable for

operation on single phase230V±10%,50Hz AC

supply,complete, as required.The unit shall have

automatic force shut down provision incase of fire on

receiving signal from BMS System.The cooling

capacity of indoor unit will be at air inlet conditions of

27Degree CD Band 19 Degree CWB temperature.

3 Indoor VRF Units (Nominal Capacity) - Wall

mounted type Unit

Supply, Installation, testing & commissioning of Wall

mounted type Unit of suitable capacity suitable to

operate from 230+10% volt, 50 HZ, 1 phase power

supply with cordless remote control, fittings &

required cable to connect indoor unit to

socket.Refrigerant Pipe size and gas quantity should

suit to the copper pipe length at actual.The capacity

guarantee should be ensured by the

contractor/manufacturer. Each unit shall have high lift

drain pump, and Low gas detection system.

Supply, installation , testing and commissioning of

following minimum capacity and external static

pressureVRF/ VRV ceiling mounted ductable type

Indoor unit equipped with wash able synthetic media

pre-filter ,fan section with low noise fan / dynamically

balanced blower ,multi speed motor ,coil section with

DX copper coil,electronic expansion valve,corded

16 4 remote control, outer cabinet, vibration

isolators,drainpan,other necessary supports

etc.,suitable for operation on single phase AC supply

230V±10%,50Hz complete as required.The unit shall

have automatic force shut down provision in case of

fire on receiveing signal from BMS System.The cooling

capacity of indoor unit will be at air inlet conditions of

27 Degree C DB and 19 Degree C WB temperature.

Mid Static Ductable units (minimum 45 pascal

external static pressure)

20 5 Refrigerant Piping for VRF system -

Digitally signed by JAYA

UNITS QUANTITY RATES DSR AMOUNT NSOR AMOUNT

Supply,Installation,testing and commissioning

including vaccumiazation and Nitrogen testing of

following nominal sizes of soft /hard drawn copper

refrigerant piping for VRV /VRF system ,complete with

fittings, with suitable adjustable ring type hanger

21 supports, jointing /brazing including accessories

,insulated with XPLEClass-Otubular insulation

/withClass-Oclosed cell elas to metric nitrile rubber

tubular sleeves sections o specified thickness as given

below for Suction and Liquid lines ,all accessories as

per specifications etc. as required :

5.1 6.4mmdia(OD)(Softdrawn)withtubethickness1.2mmwit

h19mmthick insulation

5.2 9.5mmdia(OD)(Softdrawn)withtubethickness1.2mmwit

h19mmthick insulation

5.3 12.7mmdia(OD)(Softdrawn)withtubethickness1.2mmw

ith19mm thick insulation

5.4 15.86mmdia(OD)(Softdrawn)withtubethickness1.2mm

with19mm thick insulation

5.5 19mmdia(OD)(Harddrawn)withtubethickness1.2mmwit

h19mmthick insulation

5.6 22.2mmdia(OD)(Harddrawn)withtubethickness1.2mm

with19mm thick insulation

5.7 25.4mmdia(OD)(Harddrawn)withtubethickness1.2mm

with19mm thick insulation

5.8 28.58mmdia(OD)(Harddrawn)withtubethickness1.2m

mwith19mm thick insulation

6 34.9mmdia(OD)(Harddrawn)withtubethickness1.62m

mwith19mm thick insulation

31 Drain Piping for VRF system

NS-96 Providing & fixing of heavy duty PVC Pipe complete

with fittings, supports as per specifications and duly

32 insulated with 6 mm thickness of closed cell tubular

nitrile rubber as required & as per specifications.

33 40 mm dia with 9 mm thick insulation Mtrs. 16 393.15 6,290.37

34 32 mm dia with 9 mm thick insulation Mtrs. 65 324.89 21,117.82

35 25 mm dia with 9 mm thick insulation Mtrs. 100 288.79 28,878.76

NS-97 Providing and fixing of control cable of 2 Core x 1.5

36 sqmm. shielded cable in Heavy duty PVC conduit Mtrs. 100 288.28 28,827.54

(20mm dia.) complete in all respect & as required.

NS-98 Providing and fixing of control cable of 3 Core x 1.5

37 sqmm. shielded cable in Heavy duty PVC conduit Mtrs. 20 387.11 7,742.25

(20mm dia.) complete in all respect & as required.

NS-99 Providing and fixing of control cable of 8 Core x 0.75

38 sqmm. shielded cable in Heavy duty PVC conduit Mtrs. 120 531.84 63,820.65

(20mm dia.) complete in all respect & as required.

Supply, Installation, testing and commissioning of

necessary fittings, Y-joints and headers etc.

Supplying, fixing, testing and commissioning of Main

centralized controller intelligent touch manager (Push

Button Type) suitable for groups of indoor units to be

41 NS-101 installed for control (BMS Compatible).All required Sets 1 69,261.40 69,261.40

accessories (hardware and software) to be provided

for BMS connection.

Gas Charging of complete VRF System comprising

42 NS-102 Outdoor unit of indoor unit including pressure Lot 1 2,435.63 2,435.63

43 NS-103 INLINE FAN

Supply, installation,testing and commissioning of

Inline fan suitable for following capacities complete

with sheet metal casing, electric motor and

centrifugal fan suitable for operation on 220 V ±

44 10%,50 Hz, 1 phase AC supply fitted with speed

regulator, 15 Amp plug and wiring between the fan

and the socket and accessories like gravity louvers ,

wire guard, bird screen & canvas connection etc.

46 NS-104 PROPELLER FAN

Supplying, installation, testing & commissioning of

Propeller type fans for following capacities complete

with electric motor suitable for operation on 220 V ±

47 10%,50 Hz, 1 phase AC supply fitted with speed

regulator, 15 Amp plug and wiring between the fan

and the socke, mountings, frames, louvers and bird

49 NS-105 Insulation/ Accoustic Lining

50 Duct Acoustic Lining

Providing and fixing duct acoustic lining with 25 mm

thick Non woven polyster fibre insulation of density 32

51 kg/m3, covered with 0.6 mm perforated aluminium

sheet, nuts, bolts etc. complete as per specifications

53 NS-106 Nitrile Rubber Insulation(AC Duct) (Class 'O')

Digitally signed by JAYA

UNITS QUANTITY RATES DSR AMOUNT NSOR AMOUNT

Supplying and fixing of following thickness closed cell

Nitrile rubber (Class "O") insulation , on existing duct

after applying suitable adhesive for Nitrile rubber. The

54 joints shall be sealed with 50 mm wide and 3 mm

thick self adhesive nitrile rubber tape of same material

and finish as that of the insulation complete as per

specifications and as required.

56 NS-107 Grilles / Diffusers/ Dampers / Louvers

57 GI Volume Control Dampers for Ducts Sqm 2 9,927.26 19,854.53

58 Al Volume Control Dampers for Grilles Sqm 15 9,024.79 1,35,371.78

Flexible canvas connection double layer fire rated for

60 NS-109 Out Door Stand Nos. 4 11,732.22 46,928.88

61 NS-110 SUB HEAD 'B' - AIR DISTRIBUTION

Supply, installation, balancing and commissioning of

fabricated at site GSS sheet metal rectangular/round

ducting complete with neoprene rubber gaskets,

62 elbows, splitter dampers, vanes, hangers, supports

etc. as per approved drawings and specifications of

following sheet thickness complete as required.

63 Thickness 0.63 mm sheet SQM. 120 2,075.58 2,49,069.60

Supplying & fixing of powder coated extruded

64 aluminium Return/Exhaust Air Grills with louvers but SQM. 15 11,732.22 1,75,983.30

without volume control dampers complete as required.

Digitally signed by JAYA

Construction of Regional office Building at Khurdha (Odisha)

A Furniture UNIT RATES

Providing and placing in position of double bed of

Dimension: 1910mm(L) x 2082mm(D) x 1050mm(H).

Complete structure ( headboard frame, tail board frame and

side frame) made out of 18mm thk Pre-Lam MDF Board and

bottom made out of 12mm thk Pre-Lam MDF Board with

Matching PVC lipping. ( ± 5% Varaition allowed).

Providing and placing in position of Bed Side Table

of Dimension: 450 (L) x 40mm(D) x 450mm(H).

BED SIDE Complete structure (Top Bottom and side frame) made out

TABLE - of 18 mm thk Pre-Lam MDF Board and Back made out of

9mm thk Pre-Lam MDF Board with Matching PVC lipping. (

± 5% Varaition allowed).

2 seater Dimension(L)1390mm X (D)750mm X (H)710mm.

Supplying, and placing in position of sofa as per Image.A

supple Camel Brown premium Leatherette upholstery adds

class to the soft cushioned backrest and seating. The rate of

high quality Leatherette used shall be approx Rs. 350/ mt.

Sitting proudly on sleek steel legs the sofa exudes a sense of

comfort that is perfect for any space. Material &

subtype:Premium Leatherette, Colour & Colour

Family:Brown-Camel Brown, Seating Height:16.14"

2 SEATER ,Legs:Stainless Steel, Finish:Matte, Size:Compact,

SOFA Style:Modern, Texture:Two Tone. steam beech solid wood

have used for framing construction of sofa .The seat cushion

is made of multi layered foam of density 35-38 kg/m3. The

seating cushion have 2.75 & 1.75 inches of elastic webbing.

The thread used is nylon bonded to provide lasting stitch

strength . The backrest has a foam of 28kg/m3 with polyster

polyfill outer layer of 200 gsm. The polyster polyfill keeps the

upholstery wrinke free & soft. The unit should be complete

as per image, and specification under the guidance of

Engineer in charge. ( ± 5% Varaition allowed)

1. Providing and Placing computer table size shall be 1200

Width mm ±20 mm x 600 Depth mm±10 mm x 750 Height

mm ±10 mm. 2. Table top shall be 18 mm PLPB with 35

KGS, shelf shall be 12.5 KGS drawer shall be 506 KGS. The

table top shall be 18 mm prelam particle board, 3 mm PLPB

COMPUTER board. 3. Metal parts shall be BM Slide For Keyboard

TABLE Hardware shall be Screw , KD fitting , Wooden Dowel , PVC

ibserts. 4. Construction shall be KD fitting, Wooden dowel &

Angle Clit. 5. Provision of side understorage and CPU storage

KBPT in build of wooden material along with the side drawer

should be there. 6. Shall have foot rest and modesty panel

made of particle board or wood. (± 5% Varaition allowed)

Supplying, and placing in position of full height storage as

per photograph/drawing. storage unit having Openable

shutters with shelf in it. The modular storage unit top shall

be made from 18 mm thick pre-laminated particle board and

rest of the sides as well as shelves and shutter to be made

up of 18 mm thick pre-laminated particle board while back to

be made of 8 mm thick pre-laminated particle board. All

edges to be provided with 2 mm thick PVC lipping. Each unit

to have openable shutters with locking provision. (± 5%

Varaition allowed)

Digitally signed by JAYA

A Furniture UNIT RATES

Supplying, and placing in 3 seater Dimension (L)1905mm X

(D)890mm X (H)870mm.Classic Contemporary design and

slender curves. The Sofa of stands Firm on solid PVC legs

with thick armrests that are slightly curved on the front face

of the sofa. Each curve defines a seating space which

provides for people to be seated comfortably. Finished in a

Brown Nappa Aire Leatherette (Market rate upto Rs. 800.00

per meter length + 10% variation) , the sofa makes a

3 SEATER fantastic first impression. The Cushioning is molded such

SOFA that it flows along the partition for a clean unified look.

steam beech solid wood have used for framing construction

of sofa The seat cushion is made of multi layered foam of

density 32-35kg/m3. The seating cushion have 2.75 & 1.75

inches of elastic webbing. The thread used is nylon bonded

to provide lasting stitch strength . The backrest has a foam

of 28kg/m3 with polyster polyfill outer layer of 200 gsm. The

polyster polyfill keeps the upholstery wrinke free & soft. ( ±

5% Varaition allowed).

Providing, and placing in position of reception Table Size

2100 X 750 X 1100mm.The Table top made up of 25 mm

thick BWR plywood (IS:303 grade) with 0.8mm thk post

lamination with COREAN TOP and understructure shall be

made out of 25mm thick BWR plywood with 0.8mm

post lamination. Modesty & side panel shall be 25mm thk

BWR plywood with 0.8mm thk post lamination . Table top

height will be 750mm with 600mm width from the floor level

for inner side & one additional top height 1100 mm with

width 300mm from the floor level in front modesty .

7 The working edges shall be provided with machine Nos 1 2,61,830.48 261830.48

pressed 2mm thick PVC edging using special hot melt glue at

hot temperature. Provision of BWR Plywood with post

laminate Mobile pedestal of size 400mm(L) x

450mm(D)x600mm(HT) (2 drawer + 1filling). Pedestal

Top made out of 18mm thick BWR plywood with post

laminate and rest all storage to be made out of 18 mm

thick BWR plywood with post lamainate . All exposed edges

shall be provided with machine pressed 2 mm thick PVC

lipping glued with hot melt EVA glue. All exposed surface

shall be cover with COREAN.(± 5% Varaition allowed)

(Providind and Supplying round table of size 1000mm dia .

The Worktop shall be made of 25mm Prelamparticle Board of

Grade II , Type-II as per IS:12823 and backing laminate of

0.6mm All the exposed edges are finished with 2mm thick

8 PVC lipping machine pressed. Understructure is made of Nos 5 7,236.61 36183.05

18mm Prelaminated Particle Board and fixing is through

Minifix / Dowels. The above furniture should be as per

specification and sample approved by client.( ± 5% Varaition

Providing and supplying Stool / Chair for table . The stool

has Wooden Coloured base with foot support . It has plastic

CANTEEN seat shell with Cushioned Seat wrapped in Leatherite /

CHAIR Fabric . Seat dimensions are 380 - 420 mm W x 365 - 400

mm D , Back dimensions are 245 - 350 mm Ht - 350 . 420

mm W .( ± 5% Varaition allowed)

Digitally signed by JAYA

A Furniture UNIT RATES

Supplying, and placing in position of Compactors as per

layout plan, with knock down construction mechanical driven

mechanism made of 20 GUAGE thick CRCA steel, Under

carriage shall have a welded frame made of HR Sheet. The

steel parts shall be pre-treated epoxy powder coated with

approved colour with a dry film thickness of

minimum 40 microns. The compactor shall be divided into 4

compartments with four shelves in each cabinet, shelves of

COMPACTO 18 GUAGE thickness with stiffeners at centre for taking more

R load of the material. It should have provision for guide

915 x 900 x channels which consists of J section minimum 2 mm thick HR

2000 sheet & 25 mm square bar. It shall have steel inserted

round PU handle, label holder of dimensions 155x106 mm

and other fittings nuts & bolts and with all product hardware.

The compactor height from ground shall be minimum 2000

mm. Compactors have a locking knob near the Drive Wheel

for manual locking of individual units when a person is using

those units.Complete as per image, and specification under

the guidance of Engineer in charge. (± 5% Varaition

Supplying, and placing in position of Compactors as per

layout plan, with knock down construction mechanical driven

mechanism made of 20 GUAGE thick CRCA steel, Under

carriage shall have a welded frame made of HR Sheet. The

steel parts shall be pre-treated epoxy powder coated with

approved colour with a dry film thickness of

minimum 40 microns. The compactor shall be divided into 4

compartments with four shelves in each cabinet, shelves of

COMPACTO 18 GUAGE thickness with stiffeners at centre for taking more

R load of the material. It should have provision for guide

915 X 450 X channels which consists of J section minimum 2 mm thick HR

2000 sheet & 25 mm square bar. It shall have steel inserted

round PU handle, label holder of dimensions 155x106 mm

and other fittings nuts & bolts and with all product hardware.

The compactor height from ground shall be minimum 2000

mm. Compactors have a locking knob near the Drive Wheel

for manual locking of individual units when a person is using

those units.Complete as per image, and specification under

the guidance of Engineer in charge. (± 5% Varaition

Providing and placing wooden storage of size 900 x 450mm

and height 2100mm openable storage. Finishes and

Material: The storage unit is made from 18mm

prelaminated board. All the exposed edges are with 2mm

PVC egde Imported banding & sealed edges are with 0.8mm

thick PVC Imported edge banding. The top, side and hinged

12 shutters are sealed with 2mm thick PVC edge banding.Side Nos 4 12,170.66 48682.65

Storage is a combination of open shelves and hinged door

unit and is made of 18mm thick pre laminated partical

Board. . The back of the unit is made from 18mm

prelaminated board. All the exposed edges are with 2mm

PVC egde Imported banding & sealed edges are with 0.8mm

thick PVC Imported edge banding. The top, side and hinged

Visitor Chair Providing and placing in position of medim mesh

back chair. The chair with 2 way adjustable armrests.

Material & Subtype: Mesh, Colour & Colour Family:

Black, Dimension(W)590mm X (D)508mm X (H)990mm,

Back Type: Medium Back, Base:. nylon structure with

13 nylon net on back, Base Type: cantilever, SS Pipe 30 MM Dia Nos 25 5,591.93 139798.14

16 Guage, Maximum Seating Height:21.25" ,Minimum Seat

Height:17.32" . The Seat is made up of moulded foam of

density 35-38 kg/m3 with inner & outer cover and

upholstered with fire retardant fabric of 250 GSM. (±

5% Varaition allowed)

Digitally signed by JAYA

A Furniture UNIT RATES

Workstation 1200mm x 600mm + pedestal : Providing and

placing panel & tile based modular workstation, with

partition thickness as 58 mm thk. and height of 1200mm

including powder coated (DFT 60 microns) Aluminium trims.

Tiles: Top tiles are fabric tackable and prelam.

Bottom tiles- Plain metal. INTERMEDIATE BLOCKS:

Intermediate blocks are given in Laminate finish. Wire

Management- Wires shall be taken into the system through

cable ducts from the junction boxes and it is carried up to

WORKSTATI the panels through concealed conduits inside the blocks.

ON TABLE - Side panels or legs- out of 25mm thk. prelaminated particle

1200X600X board with flat 2mm thk. PVC lipping edge banding

750MM considered only on the open end conditions or metal powder

coated legs at the end and shared condition. System shall

also have 120mm high powder coated standalone panel legs

to give the system an elevated look. Worksurface- out of

25mm thk. prelaminated particle board with flat 2mm thk.

PVC lipping edge banding of size 1200mm width x 600mm

depth. Free standing pedestal with flat metal front, full

height free standing central locking of size 390mm width x

435mm depth x 646mm height, 3 drawer = 2box + 1file.

(± 5% Varaition allowed)

Medium Back Chair Providing and fixing Mesh Chair with

Lumber Support, Seat Size 510mm W x 510mm D, Back

Size 480m W x 520mm Ht . The chair comes with PP arms ,

Nylon base with 50mm castors . The chair has Push Back

15 CHAIR Mechanism .The chair comes with Pneumatic Gas Lift of Nos 36 6,249.80 224992.77

Stroke=95 mm . Seat Height Minimum 480mm from Ground

and Maximum 570mm. Overall size of the chair is 620 mm

W x 680 mm D x (950 mm- 1050mm) H. (± 5% Varaition

Providing & fixing in positionConferenceTableas per

architectural drawing of size 4000X1500mm in plan750mm

(ht.) in single unit,Top, sides, front to be made out of double

layer of 19mm thk. board + 3.5mm thk. Veneer on exposed

surfaces. All other surfaces to be pasted with 3.5mm to

16 4mm veneer,necessary moulding and lipping of teakwood Nos 1 3,27,617.84 327617.84

etc. of approved make , finishing with melamine polish (matt

finish) on all surfaces etc. complete in all respect as per

specification and direction of Engineer-in-charge (Premium

category Veneer base rice 300 Rs/ Sqft) (± 5% Varaition

Chair Medium Back- Providing, supplying/ fabricating and

placing/ Installation in position Medium back chair is slim

and highly comfortable conferencing seating solution for

thinktanks. The seat and backrest of this revolving chair

build in chrome platted oval shape tubular section with

intigrated lumber support maintained in design. The Seat

and Backrest is one piece construction upholstered with

quality leatherite stitched on PU foam. The seat and backrest

assembly fixed on center tilt mechanism having two point tilt

locking provision. (± 5% Varaition allowed)

Office Table- Table size shall be 1600 Width x 750 Depth x

750 . The top shall be made from 25 mm thick pre-

laminated Particle board . All the edges are sealed with 2

mm thick PVC edge band all around . Side panels shall be

made from 25 mm thick pre- laminated Particle board . All

OFFICE the edges are sealed with 2 mm thick PVC edge band on the

TABLE - user side and 0.8 mm on the top and bottom side .The side

1600X750X panels have 2 glide screws each for levelling of the desk.

18 750MM Modesty panel shall be made from 18 mm t pre- laminated Nos 3 16,446.84 49340.52

SIDE RACK - Particle board . All the edges are sealed with 0.8 mm thick

1200X400X PVC edge band all around. Freestanding Pedestal shall be

750MM made from 18 mm pre- laminated Particle board with a

combination of 2 mm and 0.8 mm PVC edge band on all the

exposed surfaces as per requirement . The drawers are

provided with suitable slides for smooth operation . All the

pedestal drawers are centrally locked with a single key.

(± 5% Varaition allowed)

Digitally signed by JAYA

A Furniture UNIT RATES

Providing & fixing in position Office table in single unit,Top to

be made out of double layer of 19mm thk. board + 3.5mm

to 4mm thk. Premium category Veneer on exposed surfaces.

All other surfaces to be pasted with veneer on inner surface

only,Drawers to be made out of 19mm thk. board + 3.5mm

thk. Premium category Veneer on exposed and horizontal

surfaces. All other surfaces to be pasted with 3.5mm to

4mm veneer,Shutter to be made out of 19mm thk. board

+3.5mm thk. Premium category Veneer on exposed

surfaces. All other surfaces to be pasted with3.5mm to 4mm

veneer,necessary moulding and lipping of teakwood etc.

finishing with melamine polish (matt finish) on all surfaces

etc.,8mm toughened glass on top of table complete in all

respect as per specification and direction of Engineer-in-

(± 5% Varaition allowed)

Providing and placing a High back chair with

ergonomic design, comfortable & aesthetically appealing

of size 1250mm(height)X 500m X600mm. The seat shall be

made of 15mm thick hot pressed commercial plywood

padded with high resilience polyurethane foam having

density 48kg/m³ and the back shall be made of plywood

padded with high resilience polyurethane foam having

density 32kg/m³. The seat and back shall be

upholstered with leatherite tapestry 0.7mm thick and

535 GSM. The backrest shall be made by keeping the

natural curvature of the spine which helps to provide

full back support as well as head support. seat & Back.

For seating durability the chair shall have torsion Bar

360 degree revolving mechanism and tilt tension

adjustment which provides back strength for the chair. The

pneumatic seat height adjustment for healthy seating, user

can adjust seat height up to 100mm with class-4 gas- lift to

suit them using the lever under the seat. The Pedestal

should have five legged made of crome Base having pitch

circle dia. 700mm fitted with 5 nos. twin wheel castors. The

castors of the chair should be injection moulded in

black 30% glass filled nylon. (± 5% Varaition allowed)

Providing and placing in position of Main Table Dimension :

2700mm(L) X 1000mm(d) x 750mm(h). Side Rack

Dimension : 1050mm(L) X 400mm(d) x 750mm(h).

Providing & fixing in position Office table in single unit,Top to

be made out of double layer of 19mm thk. board + 3.5mm

to 4mm thk. Premium category Veneer on exposed surfaces.

OFFICE All other surfaces to be pasted with veneer on inner surface

TABLE - only,Drawers to be made out of 19mm thk. board + 3.5mm

2700X1000 thk. Premium category Veneer on exposed and horizontal

21 X750MM surfaces. All other surfaces to be pasted with 3.5mm to Nos 1 1,51,830.48 151830.48

SIDE RACK - 4mm veneer,Shutter to be made out of 19mm thk. board

1050X400M +3.5mm thk. Premium category Veneer on exposed

M surfaces. All other surfaces to be pasted with3.5mm to 4mm

veneer,necessary moulding and lipping of teakwood etc.

finishing with melamine polish (matt finish) on all surfaces

etc.,8mm toughened glass on top of table complete in all

respect as per specification and direction of Engineer-in-

charge (Premium category Veneer base price 600 Rs/ Sqft).

(± 5% Varaition allowed)

Providing and placing in position wooden centre table of size

900mm x 600mm 450mm made up of teak wood frame

CENTER work. The top having 12mm thick float glass with decorative

22 TABLE 900 edge moulding, the unit having ornamental legs including Nos 1 8,881.29 8881.29

X 600 X 450 melamine polishing, all complete as per approved sample

and as per direction of Engineer-in- charge. ( ± 5%

Varaition allowed)

Digitally signed by JAYA

A Furniture UNIT RATES

Providing and placing a medium back chair of size

990mm X 500mm X600mm with ergonomic design,

comfortable & aesthetically appealing. The seat shall be

made of 15mm thick hot pressed commercial plywood

padded with high resilience polyurethane foam having

density 48kg/m³ and the back shall be made of plywood

padded with high resilience polyurethane foam having

density 32kg/m³. The seat and back shall be

upholstered with leatherite tapestry 0.7mm thick and

535 GSM. The backrest shall be made by keeping the

natural curvature of the spine which helps to provide

full back support as well as head support. seat & Back.

For seating durability the chair shall have torsion Bar

360 degree revolving mechanism and tilt tension

adjustment which provides back strength for the chair. The

pneumatic seat height adjustment for healthy seating, user

can adjust seat height up to 100mm with class-4 gas- lift to

suit them using the lever under the seat. The Pedestal

should have five legged made of crome Base having pitch

circle dia. 700mm fitted with 5 nos. twin wheel castors. The

castors of the chair should be injection moulded in

black 30% glass filled nylon. (± 5% Varaition allowed)

Digitally signed by JAYA

Construction of Regional office Building at Khurdha (Odisha)

ABSTRACT OF COST

A. Septic Tank ( for 100 Users)

DSR- AMOUNT DSR AMOUNT

S.N. DESCRIPTION OF ITEM QUANTITY UNIT RATES

2023 ITEM [M.R. ITEM]

Earth work in excavation by mechanical means

(Hydraulic excavator) / manual means over areas

(exceeding 30cm in depth. 1.5 m in width as well as

1.0 10 sqm on plan) including disposal of excavated 2.60

earth, lead upto 50m and lift upto 1.5m, disposed

levelled and neatly dressed.

All kinds of soil 2.6.1 48.00 CUM 260.30 12,494.40

2.0 Extra for every additional lift of 1.5 m or part thereof

banking excavated or stacked materials.

All kinds of soil

Supplying and filling in plinth with sand under

floors, including watering, ramming,

Providing and laying in position cement concrete of

specified grade excluding the cost of centering and

shuttering - All work up to plinth level

1:3:6 (1 cement : 3 coarse sand : 6 graded stone

aggregate 40 mm nominal size)

Providing and laying in position machine batched and

machine mixed design mix M-25 grade cement

concrete for reinforced cement concrete work, using

cement content as per approved design mix, including

pumping of concrete to site of laying but excluding

the cost of centering, shuttering, finishing and

4.0 reinforcement, including admixtures in recommended 5.33

proportions as per IS: 9103 to accelerate, retard

of concrete, improve workability without impairing

strength and durability as per direction of

Engineer-in-charge.

(Note :- Cement content considered in this item is @

330 kg/cum. Excess/less cementused as per design

mix is payable/recoverable separately).

All works upto plinth level 5.33.1 11.65 CUM 9,504.75 1,10,730.34

Lintels, beams, plinth beams, girders, bressumers and

Suspended floors, roofs, landings, balconies and

access platform

Steel reinforcement for R.C.C. work including

7.0 straightening, cutting, bending, placing inposition and 5.22 980.00 Kg 107.85 1,05,693.00

binding all complete upto plinth level.