SPL REPAIR WORK TO BLDG NO P-41/1 TO 4 (OR MD ACCN), BLDG NO MES-16 (SINGLE OR LIVING), BLDG NO MES-62 (STORE), BLDG NO MES-134 (RATION STORES) OF 100 FD REGT AND EXTERNAL ELECTRIC SUPPLY AND INSTALLATIONS AT ARMY CAMP JAMSHEDPUR UNDER GE RANCHI

Amount

Demolition of plain cement concrete in ground floor and paving not exceeding 15cm thickness below or above ground level including removal of same to exceeding 1 Km but not exceeding 1.5 Km, complete all as specified and directed.

M&L PCC (1:5:10) type E-2 using 40mm graded brick aggregate as in sunken portion, complete all as specified and directed.

M&L PCC (1:2:4) type B-1 using 20mm graded stone aggregate as in sunken floor .average thickness 40mm and making adequate slop towards spout pipe etc, complete all as specified and directed.

M&L bitumen blown 85/25 applied hot two coats to concrete surfaces at rate of 1.5 Kg/sqm per coat complete all as directed at site, complete all as specified and directed. Make : STP

M&L polythene film black 50 micron laid in floors/Walls etc, complete all as specified and directed.

Taking down cement plaster on brick wall or concrete surface etc including raking out joints hacking for key scrubbing down with water etc, complete all as specified and directed.

M&L rendering 15 mm thick on fair faces of bricks/concrete surface in cement mortar (1:6) on wall finishing the surfaces even and smooth without using extra cement, complete all as specified and directed.

M&L rendering 15 mm thick on fair faces of bricks/concrete surface in cement mortar (1:4) with using on wall finishing the surfaces even and smooth without using extra cement, complete all as specified and directed.

M&L for 10 mm thick cement plaster in cement mortar 1:3 for ceiling, finished even & smooth without using extra cement, complete all as specified and directed.

M&L for repair and rendering 10mm thick in CM 1:3 on chajjas not exceeding 60cm width after removing cracked plaster and concrete including cleaning of viisible reinforcement and treating with cement slurry also necessary repair to cracked concrete if any with cement concrete 1:2:4 Type B-0 using 12.5mm graded aggregate including necessary scafolding work for double/single storey bldgs, complete all as specified and directed.

Dismantling steel window and ventilators including guard bar etc complete and removing to MES store all as directed at site, complete all as specified and directed.

S&F aluminium anodised aluminium window shutter Sliding type with frame of anodised aluminium channel section suitable for sliding aluminium shutters weighing not less than 0.55Kg/M including necessary joining cleats glazing clips rubber packing anodised aluminium shop beading screws with two shutter Including 3.5mm thick coloured glass and one shutter with stainless steel wire gauze including necessary locking arrangement and handle etc; as specified etc, complete all as specified and directed.

S&F anodised aluminium ventilator shutters fixed or louvered type without sash bar, aluminium section weighting not less than 0.55 Kg/M including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws and 4 mm thick figured glass fixed in fram etc, complete all as specified and directed.

S&F frame work such as grills, grating etc with ends of bars shouldered and or rivetted or forged into spikes, framed guard bars, barred iron doors, ladders etc and similar wks conforming to Fe-290 Gd E-165, complete all as specified and directed.

Taking down chowkhats or frame n.exc 1.50 Sqm each with shutter (without taking of shutter from framed) complete incl removing from site, complete all as specified and directed.

Taking down chowkhats or frame exc 1.50 Sqm but n.exc 4 Sqm each with shutter (without taking of shutter from framed), complete all as specified and directed.

Taking down shutters of any description exc 1 sqm and n. exc 2 sq m each and removing from site, complete all as specified and directed.

S&F solid PVC Double door frame of size 50mm x 95mm made out of 5mm wood grain printed sheet PVC sheet reinforced with M.S.tube, suppling & fixing in opening as per specification & drawing, complete all as specified and directed.

S&F factory made solid PVC Moulded door shutter 28 to 30 mm thick(stiles) with 2 mm thick prelaminated Moulded PVC sheet polyurethane painted on the front face & 2 mm plain colour PVC sheet on back faces,and with particle board core supplying and fixing in frame at site as per specification and drawing.

M&L 2nd class hard wood plain,solid straight chowkhats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints supplied and fixed, complete all as specified and directed.

M&L 30 mm thick flush shutters solid core construction,with block board core and plywood face panels,commercial type on both sides, complete all as specified and directed.

S&F 30mm thick 2nd class HW Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats, complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS Square tube S&F in opening all as shown on drawing, complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick style consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheets strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail and bottom rail on either side and as gap inside for top rail and bottom rail paneling of plain colour PVC sheet to be fitted in the MS frame welded/seated to the stiles and rail with suitable PVC sheet bending and jointed to gather with solvent cement supplying and fixing in the frame at site as per specification and drawing, complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or stainless steel wire staples, complete all as specified and directed.

S&F Hasp and staple safety type aluminium anodized hinges pin incl bolt to hinges plate 125 mm long, complete all as specified and directed.

S&F butt hinges 100mm long medium weight cold rolled MS and fixed complete all as directed at site, complete all as specified and directed.

S&F extruded aluminium alloy butt hinges 100mm size type B-21, complete all as specified and directed.

S&F 150 mm long aluminum anodized barrel tower bolt extruded section.

S&F aluminum handles cast type anodised 150 mm long.

S&F 300 mm long of bolt Mild steel sliding door bolts,plate type,stove enamelled black,with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts,four on bolt plate and two on staple plate, complete all as specified and directed.

S&F for 300mm ordinary rat tail rod pattern springs including roller and roller plate of Brass, complete all as specified and directed.

S&F mild steel works as in small articles like hold fasts, conforming to Fe-290 or Fe E-165, complete all as specified and directed.

Cutting holes in brick walls in cement mortar for inserting holdfasts and making dismantaled portion in CM (1:3) or cement concrete 1:2:4 Type B-1, depth of embedded portion of holdfasts not exc.half brick, complete all as specified and directed.

Taking up or down steel tubing and connection of 15 mm bore complete all as specified directed at site.

All as item No 35 above but for 20 mm dia bore pipe.

S&F steel tubing and connection tubing in new or old position to walls, ceiling, floors etc including all fitting as socket,elbow,nipple,union etc complete all as directed at site for 15 mm bore, complete all as specified and directed.

All as per item No 37 above but for 20 mm dia.

Dismantling of boarding any description, fixed in any position with screws, complete all as specified and directed.

S&F prelaminated particle board 18-19 mm thick interior grade prelaminated one side with decorative choice lamination and other side balancing white lamination to timber frame work in cupboard, complete all as specified and directed.

M&L for 2nd class hardwood of sectional area exc.15 Sqm & n.exc 25 sqcm in plain fillets,square rectangular in section,clean sawn,secured with nails, complete all as specified and directed.

S&F 30mm width of flaps continues piano hinges mild steel bright finish or electrogalvanised, complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern) including all fittins,heads,shoes,bends,swan-necks,etc including removing from site, complete all as specified and directed.

M&L 110mm bore, PVC (SWR) pipes, single socketed, in any length, with rubber ring joints fixed on walls/floors including PVC clamps fixed to wall properly including fixing of pipe with PCC (1:2:4), complete all as specified and directed.

M&L for 75mm bore, PVC (SWR) pipes, single socketed, in any length, with rubber ring joints fixed on walls/floors including PVC clamps fixed to wall properly including fixing of pipe with PCC (1:2:4), complete all as specified and directed.

M&L for 40mm dia of low density polyethylene (LDPE)of pressure rating 6 kgf/sqcm fixed to walls,ceilings or in floors etc, complete all as specified and directed.

S&F PVC (SWR) bends 110 mm bore of any radius.

S&F PVC (SWR) bends 75 mm bore of any radius.

S&F PVC (SWR) junction single (singleT) equal or unequal 110mm bore provided with access door.

S&F 110 mm bore PVC (SWR) vent cowl.

S&F 75 mm dia outlet PVC (SWR) floor trap plain with steel grating including jointing with solvent cement.

S&F 110mm dia PVC (SWR)WC connector with lip ring.

Excavation in trenches not exc 1.5 mtr wide and not exc. 1.5 mtr deep for foundation in soft/loose soil & getting out, complete all as specified and directed.

Demolition and breaking up drain pipe 100 mm internal dia of pipe (salt glazed ware, AC or reinforced concrete) set in cement mortor, complete all as specified and directed.

Returning filling in trenches including spreading leveling and well ramming with water complete n.exc 25 cm thick in each layer in soft/loose soil, complete all as specified and directed.

Removing exavated soild n.exc 50 mtr and depositing where directed at a level n.exc 1.5 mtr above the starting point.

M&L for 100 mm dia of reinforced concrete pipe, class NP2, laid and jointed complete with collars, complete all as specified and directed.

M&L PCC 1:3:6 type C-2 using 40 mm graded stone agg for concrete bed to drain pipes including , packing under and haunding against the sides of pipe, after they tested for 100 mm dia pipe, complete all as specified and directed.

Demolition of brick work built in cement mortar, complete all as specified and directed.

M&L brick work using sub class B bricks straight of curved on plan exc 6m mean radius built in CM (1:4), complete all as specified and directed.

M&L brick work with sub class ‘B’ bricks straight or curved on plan to any radius in half brick wall built in CM (1:4), complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in coping, bed plate etc, complete all as specified and directed.

M&L precast cement concrete type B-1 (1:2:4) using 20mm graded aggregate as in cover slab, shelves, and similar work set in CM (1:4), complete all as specified and directed.

M&L cement concrete (1:3:6) type C-2 (using 40mm graded stone aggregate) as in lean concrete for foundation in drain,manholes etc, complete all as specified and directed.

M&L for mild steel TMT bars 8 to 10mm dia and over cut to length bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

M&L rendering 10mm thick on fair faces of brick or concrete surfaces and finishing the surfaces fair and even without using extra cement in CM (1:4) with W.P.C (W.P.C will be measured and paid separately), complete all as specified and directed.

Supply only integral water proofing compound. Make - ACCO PROOF/WATER SEAL/ IMPERMO

Removing/taking down of old water proofing treatment from roof/concrete surface removal to distance exc 250mtr and n.exc. 500mtr from the site & cleaning of the roof surface with wire brush to make it free from dust, dirt etc, complete all as specified and directed.

Demolition of cement concrete of any description and in any position, complete all as specified and directed.

Brushing neat cement slurry with 3kg of cement per Sqm, complete all as specified and directed.

M&L cutting out cracks to V-section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3, complete all as specified and directed.

M&L 25 mm thick PCC 1:2:4 type B1 using 20mm graded stone aggregate as in floor using liquid water proofing compound to make surface in level complete (liquid WPC shall be measured seperatly).

M&L providing, cement concrete 1 : 2 : 4 type B-0 using 12.5mm graded stone aggregate as in roof kerbs or mud stops, rounded or chamfered on edges with using water proofing compound(liquid WPC shall be measured seperatly), complete all as specified and directed.

M&L bedding layer of mortar 10mm thick finished fair and even in CM 1:4 mixed with liquid water proofing compound (liquid WPC shall be measured seperatly).

Supply only liquid water proofing compound, complete all as specified and directed.

M&L cleaning plastered roof surface and applying a coat of Oxidised bitumen based solvented primer @ 0.3 kg/Sqm of approved make on top of dry surface of RCC roof, complete all as specified and directed.

M&L for applying a tack coat of industrial bitumen 85/25 at the rate of 1.2Kg per sqm including cleaning surface before laying of APP Membrane, complete all as specified and directed.

M&L APP modified polymeric waterproofing membrane 3mm thick with non woven polyster core of approved make applied by heating one surface of membrane with torch sealing with lap of 100mm and the overlap shall be selaed by flame complete all as per manufacturer instructions, complete all as specified and directed.

M&L for applying protective coating with bituminous based aluminium/Heat resisting paint in two coats, complete all as specified and directed.

S&F in repair for 10ltrs capacity flushing cistern PVC low level valve less, symphonic action type flushing cistern white with inlet, ball valve, float and handle including brackets and 32 mm flush pipe of polyethylene, complete all as specified and directed.

S&F in repair 20mm bore stop valves cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe, complete all as specified and directed.

S&F in repair, 15mm bore bib taps cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule, complete all as specified and directed.

S&F for 15mm bore stop valve cast copper alloy, fancy type chromium plated with long shank and cup (concealed) screwed down,high pressure with crutch or butterfly handle, screwed both ends for iron pipe, complete all as specified and directed.

S&F in repairs for shower rose chromium plated with or without swivel joints 75 mm dia, complete all as specified and directed.

S&F in repair for vitreous china squatting pan ORRISA Pattern of size 580x 440mm white with integral foot rest and 's'or 'p trap'complete (excluding cistern and flush pipe) with provn of lime concrete including backing joints, complete all as specified and directed.

S&F for vitrious china wash basin, white flat back size 550 x 400 mm including waste, chain & plug and poreclain stopper and bracket etc. Complete including cutting for and pinning in ends of brackets or errecting bracket and 32mm dia waste fitting brass chromium plated for WHB etc;with long screwed shanks and fly nuts,flange end bedded in red lead cement including 32mm dia waiste pipe fitted, complete all as specified and directed.

S&F for pillar tap of 15mm dia bore pipe, fancy type cast copper alloy with capstain head chromium plated with or without lettered “hot or cold” with long screwed shanks and fly nuts screwed for iron pipe fixed, complete all as specified and directed.

S&F PVC connection pipe of 15 mm dia and 45 cm long to WHB and flushing cistern, complete all as specified and directed.

S&F in repair stainless steel kitchen sink with drainage board 1 mm thick including bedding in cement mortor on to dwarf wall or including fixing centilever brackets over all size 915 mm x 460mm bowl size 410 mm x 330 mm x 160 mm and including 38/40mm dia waiste pipe, complete all as specified and directed.

S&F stainless steel uternsil rack not less than 1 mm thick of approved quility and fixed in kitchen, complete all as specified and directed.

Disconnecting existing tank of capacity exc.250 & n.exc 500 ltrs, setting aside lowering if required for repairs cleaning etc and hoisting if required reconnecting and refixing in position, complete all as specified and directed.

S&F 500 ltr capacity Rotational moulded polyethylene water storage tank (cylindrical vertical closed top) hoisted and fixed in positions all as specified in SSR Part-I,including 20 mm dia of ball valves high pressure of PTMT with epoxy coated aluminium rod &highdensity plastic ball screwed for iron pipe and fixed, complete all as specified and directed.

M&L 20 mm thick granite tiles machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing as in kitchen slab, complete all as specified and directed.

M&L for applying three coats of white wash on old plastered surfaces of ceilings after necessary preparation of the surface, complete all as specified and directed.

M&L for preparation of old decorated surface of walls by brooming down and wire brushing etc and applying two coats of white wash on wall, complete all as specified and directed.

M&L for Preparation of old plastered or unplastered surfaces of ceiling and applying two coats of white wash to ceiling, complete all as specified and directed.

M&L for preparing newly plastered surfaces applying distemper oil emulsion two coats on 3mm thick wall care putty (in two layers) including priming coats complete.

Complete removal of existing treatment of walls/ ceiling and applying two coats of distemper oil emulsion over 3mm wall care putty (in two layers) including priming coats, complete all as specified and directed.

M&L for preparing the newly surface of any description not otherwise described over 10 cm width or girth on steel surface and applying two coats of synthetic enamel paint over one coat of zinc chromate primer, complete all as specified and directed.

M&L for preparing the new plastered surfaces of wall and applying two coats of cement base paint of any colour over one coat primer, complete all as specified and directed.

M&L complete removal of existing treatment on wall and applying two coats of cement base paint of any colour over one coat primer, complete all as specified and directed.

M&L for 10 mm thick cement plaster in CM (1:4) for backing of tiles, complete all as specified and directed.

M&L for colour glazed ceramic tiles in vertical surfaces 300x450x7to 8mm/350x250x7mm/450x350x7mm thick set and jointed in neat cement slurry & pointed in white or coloured cement to match the surfaces complete.

M&L for 15 mm thick screed bed or bedding layer in CM (1:6), complete all as specified and directed.

M&L non skid coloured ceramic tiles 7 to 8 mm thick(square/rectangular) area of each tiles exceeding 0.11 Sqm but n.exc 0.18 Sqm in floor etc and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces, complete all as specified and directed.

M&L non skid coloured ceramic tiles 7 to 8 mm thick(square/rectangular) area of each tiles exceeding 0.18 Sqm but n.exc 0.38 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces, complete all as specified and directed.

All as per item No 106 above but in skirting, dado etc over and including 10 mm thick cement plaster in CM (1:4) complete all as per specified and directed.

M&L for machine cut Kota stone slab flooring 18-20 mm thick (square or rectangular size.) laid over and including 20mm thick screed bed in CM (1:4) and pointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and directed.

All as per item No 108 above but on vertical surface as dado/ skirting.

S&F mild steel, chromium plated with fixing brackets, tops, rollers etc fixed in position including fixing decorative type bracket, complete all as specified and directed. s.

S&F CP soap tray fixed with rawl plugs, complete all as specified and directed.

S&F brass CP tubular towel rail 20mm dia D type 60cm long between flanges, complete all as specified and directed.

S&F Glass shelf of size 500mmX125mm consisting sheet glass with CP brackets and CP frame Size 500mm long, complete all as specified and directed.

Dismantling timber scantling under 40 sqcm in section (Unframed work) as in filets, rails post, rafter etc, complete all as specified and directed.

Dismantling of wall and ceiling boards any thickness including corner fillets, complete all as specified and directed.

M&L for E-board ceiling sheet 600x600x4 mm thick fixed on GI Snap grid system (consisting of angle or tee section size 24 x 24 x 1.5mm thick angle section and 24 x 32 x 1.5 mm Tee Section) GI snap grid hanging with 03 mm dia GI hanger/wire fixed with steel dashed fastners, complete all as specified and directed..

Dismantling wrought iron or mild steel work of any description not otherwise provided, complete all as specified and directed.

S&F roof trusses (framed ) trussed, purline , crane gantries , rafter, rails and fastening and heavy brackets framing fast and similar small (beam, Tee, angle , channel plates or flat sections) including distance pieces cleats etc and necessary nuts bolts , rivets, welding, plates etc, complete all as specified and directed. Quality confirming to Fe-410-W ( Gde E-250) quality B.

Dismantling AC corrugated /semi corrugated sheets in roof covering, complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

M&L PCC 1:3:6 type C-2 , using 20mm graded aggregates as in 75mm thick plinth protection including bitumen joints in 1.0 Mtr centre to centre as required, complete all as specified and directed.

M&L brick work with sub class `B` bricks straight or covered on plan any radius built in CM 1:6, complete all as specified and directed.

M&L preparation of old wooden surfaces exc. 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

M&L for preparation of old painted steel & iron surface of any description n.exc 10 cm width or girth when connected with other painting or when painted in different tint applying two coats of synthetic enamel paint over on steel surface, complete all as specified and directed.

All as per item No 127 above but over 10 cm in width or girth, not otherwise described.

M&L for preparation of new painted steel & iron surface of any description n.exc 10 cm width or girth when connected with other painting or when painted in different tint applying two coats of synthetic enamel paint over one coat of red oxide zink chromium primer on steel surface, complete all as specified and directed.

M&L for rolled sec as in framing for door chowkat fixed with angle plate and connecting plate etc conforming to Gde- Fe -290 & Gde E-165, complete all as specified and directed.

M&L applying two coats of synthetic enamel paint over a coat of pink primer incl cleaning for new wooden surface, complete all as specified and directed.

S&F mild steel sliding door bolts plate type stone enameled black with bright bolt not less tan 12 mm dia with and including minimum of 6 bolt & nut four on bolt plate and two on staple plate 250 mm, complete all as specified and directed.

S&F straps, supports or suspenders, hooks for hanging fans , MS plates,nut bolts, hold fast , clamps ,hooks , plate and similar small article etc. confirming to Fe 290 & Gde E-165, complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, bell, socket or power) complete including fixture and tiffings such as switches, ceiling roses, pendent, regulators, socketst, light fitting etc, removing materials to store in safe custody or for taking credit and making good disturbed surfaces of walls, floors etc, complete all as specified and directed.

M&L for point wiring alongwith earth continuity conductor with 1100 volts grade PVC insulated and FR multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black, Earth - Green) FRLS grade dwawn in and including PVC casing and caping not less than 20mm size and fixing accessories and sunken galvanized pressed steel terminal boxes of thickness not less than 1.12 mm covered with 2.80 mm thick phenolic laminated white sheet cover for mounting switches, sockets, fan regulators complete including 1.0 sqmm copper stranded earth wire for all as specified for the following :-

One light point controlled by one switch.

One fan point controlled by one switch.

One bell point controlled by one switch.

One socket outlet 3 pin 5 Amp controlled by one switch on the same board.

One socket outlet 3 pin 5 Amp controlled by one switch on indepdendent board.

M&L for point wiring alongwith earth continuity conductor with 1100 volts grade PVC insulated FR multistranded copper conductor cable 2.5 sqmm (Phase - Red, Neutral - Black, Earth - Green) FRLS grade drawn in and including PVC casing and caping not less than 20mm size and fixing accessories and sunken galvanized pressed steel terminal boxes of thickness not less than 1.12 mm covered with 2.80 mm thick phenolic laminated white sheet cover for one 6 Pin 15 Amp socket outlet controlled by one switch on independent board.Incl. 1.5 Sq mm copper conductor earth wire and connected to common earth dolly on independent board, complete all as specified and directed.

S&F angle holder, insulated polycabonate body with back plate, complete all as specified and directed.

S&F switch piano flush button single pole one way 5/6 Amp, complete all as specified and directed.

S&F switch socket combination two in one 5 and 15 Amps multipurpose flush type universal 240Volts, complete all as specified and directed.

S&F socket outlet 2 in 1, 5 pin, 5/6 amp, flush type, complete all as specified and directed.

S&F ceiling rose surface bakelite 65x50mm three terminal AC 230 volts, complete all as specified and directed.

S&F in replacement Delux fan regulator ( Rotary step 100W) on the existing phenolic laminated sheet etc as required all as specified and as directed.

S&F for LED Tube light (Single side connection) ) with very high effiency suited for installation in existing tubelight G13 lamp holders to give glare free cool day light 20W LED with Regal batten for LED tube (single side connection) upto 1x22W LED tube including pre-wired equivalent Philips/Surya/ CG/Jaquar/Havells ,230 V Energy efficient with all accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable of suitable size.

S&F sheet metal enclosure DBs for using MCBs single pole and neutral 4 Way double door with 200 amp rated bus bar 240 V all as specified.

Taking down U/S MCBs/ELCBs with incoming and outgoing controls any make, any capacity after disconnecting, complete all as specified and directed.

S &F isolator Single pole and neutral 40 A, 240 V

S &F isolator Single pole and neutral 63 A , 240 V

S&F exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers.

M&L Bell push , flush type , 5 Amp, complete all as specified and directed.

S&F Bell , AC 230 Volts single pole, complete all as specified and directed.

S&F in repair, the existing panel board outdoor/indoor, fixed to the wall / platform/pole etc by replacement of old unserviceable items i.e. MCCB/MCB/Voltmeter/ Amperemeter /PT/CT/Indicators etc from panel and making new electric connections with multistandard copper cable of suitable size with lugs , welding of broken portion of panel, providing of new hinges after removing old broken hinges, handle including painting of outdoor/ indoor any type, any size and any make of panel with one coat of synthetic enamel paint of approved colour to external surface of panels etc, complete all as specified and directed. (Note : Replacement of unserviceable items i.e. MCCB/MCB/Voltmeter /Amperemeter/PT/CT/Indicators etc will be measured and paid separately with S&F under relevent items as supply only)

S&F in replacement MCCB 200 Amps, 415 volts AC with breaking capacity 36 KA, four pole complete all as specified and directed at site, complete all as specified and directed.

S&F in replacement MCCB 400 Amps, 415 volts AC with breaking capacity 36 KA, Four pole , complete all as specified and directed at site, complete all as specified and directed.

S&F in replacement MCCB , 250 Amps 415 volts AC with breaking capacity 36 KA, four pole, complete all as specified and directed.

S&F in replacement MCCB , 100 Amps 415 volts four pole 16 KA repturing capacity complete all as specified and directed at site, complete all as specified and directed.

S&F in replacement MCCB , 63 Amps 415 volts four pole 16 KA repturing capacity, complete all as specified and directed.

S&F in replacement MCB , 100 Amps 415 volts four pole 10 KA repturing capacity complete all as specified and directed at site, complete all as specified and directed.

S&F in repair only LT Current transformer of any ratio, complete all as specified and directed.

S&F in repair RYB phase indicators, complete all as specified and directed.

S&F in repair MCB TP 415 volts 10 KA 63 Amps, complete all as specified and directed.

S & F in repair LED street light fitting 1x30 watt with pressure die cast aluminium housing, heat resistant toughened glass with frame, duly prewired inbuilt LED module IP 66 Protection complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable of size 1.5 sq mm including GI tubing 40mm dia light grade 1.5m long band to shape for mounting of security light with 2 nos MS,FI clamp including plinth with nut bolts with PVC 20mm conduit for cable including clamps etc complete all as specified and directed. Make: Crompton Greaves Cat part No LSTO-45-CDL or Equivalent make of Havells/Philips/Bajaj/Wipro.

Taking down old unserviceable LT cable, Supply and Laying LT cable in trenches/through pipes/ducts or on poles/walls jointing to O/H conductor, LT panels, main switch with cable size aluminum lugs and testing. XLPE insulated, armoured heavy duty electric cables with aluminum conductor, 1100 volt grade, all as specified directed by Engineer In charge of cross sectional area and core of following sizes :- Note : (i) Excavation and earth work , sand, pipe and stone patti will be measured and paid separately

Size of cable 10 Sq.mm 2 Core

Size of cable 10 Sq.mm 4 Core

Size of cable 16 Sq.mm 4 Core

Size of cable 25 Sq.mm 3 1/2 core

Size of cable 50 Sq.mm 3 1/2 core

Size of cable 70 Sq.mm 3 1/2 core

Size of cable 95 Sq.mm 3 1/2 core

Size of cable 120 Sq.mm 3 1/2 core

Excavation in trenches not exc 1.5m wide and n. exc 1.5M deep for fdn / trenches and getting out for soft / loose soil, complete all as specified directed.

Removing excavated material any type n exc 50m and depositing at a level n.exc 1.5M above ground.

Returning/filling in layers, spreading leveling, watering and well ramming in layers n.exc 25m in sof/loose soil, complete all as specified and directed.

Supply and laying quarry ' M ' sand for cushioning for cable protection in trenches 8 cm before laying cable and 15 cm deep over the cable, complete all as specified and directed.

M&L for laying Bricks, common burnt clay building sub-class 'B' old size bricks for protection of cable in trenches, complete all as specified and directed.

M&L for Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanized earth strip of size 32x 6mm by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical Plate No 3 of MES SSR Part-I connected to main switch board or main control board all as specified and testing on completion including provision of earth strip protected by galvanized iron 40 mm dia light grade pipe and watering pipe shall be 20 mm bore light grade including all excavation and earth work in any type of strata, PCC pit with pre-cast RCC cover, charcoal/salt, funnel etc, complete all as specified and directed. NOTE :- (i) The concrete pit shall be PCC 1:3:6 type C-1, 40 mm thick pre cast cover slab of RCC (1:2:4) type B-1 using 20mm graded stone aggregate reinforced with 8mm TMT bars @ 10 cm C/C on both sides with suitable cast iron handle shall be provided in lieu of cast iron cover shown in electrical plate No 3 of MES SSR Part-I. (ii) Item includes the cost of 7.5M GI pipe for protection of earth lead. Any variation in length shall be adjusted through deviation order. (iii) Item includes cost of 7.5 M earth lead. Any variation in length shall be adjusted through deviation order. (iv) PCC pit shall be provided at least 500 mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe, bends, elbow etc shall be deemed included in the unit rate

M&L in repair of GI tubing light grade of size 80 mm for protection of cable in trenches/on pole, complete all as specified and directed.

M&L in repair of GI tubing light grade of size 50 mm for protection of cable in trenches/on pole, complete all as specified and directed.

M&L for Cutting, trimming and vending tree branches falling on overhead head lines( HT/LT)after arranging electrical shutdown from department or RSEB including taking all precautions while working on lines. [Note:- (i) The length of span between two poles shall be measured in which trees are falling on overhead electric conductors. (ii) Required T & P will be arranged by the contractor at his own cost.

M&L in repair for prestressed cement concrete pole 9 metre long, 102mm x 172mm at top and 102mm x 279mm at bottom (or nearest higher size as approved by State Electricity Board), Class-10 conforming to IS-1678-1998, over and including marking alternate white and black strips 30 cm height (Total 5 Nos), with two coats of synthetic enamel paint over a coat of primer & Pole Nos. complete all as specified and directed.

Dismantling of ACSR conductors from existing pole and removing from site, complete all as specified and directed.

M&L in repair for providing HT/LT over head lines on prestressed concrete poles with aluminium conductor steel reinforced (ACSR) including straining properly on insulator and binding with aluminium binding wire, connectors and jumpers etc complete all as specified & directed by Engineer-in-charge. (Mink, Dog, Lion, Weasel, Ferret or Squirrel). NOTE:- Measurement for the purpose of payment shall be made by measuring horizontal distance between centres of two adjacent poles and compounding the weight of conductors of that size and length and adding 3% extra for sag, joints, jumpers etc.

S&F in repair stay assembly complete comprising of MS galvanized stay plate 23cm x23cmx6mm , MS galvanised stay rod 16 mm dia with nut 215 cm long , MS galvanised stay bow 40cm long with 2 Nos galvanized thimbles with and including all fittings all as specified in SSR 2009 Part I. (Excavation , PCC for foundation, loop type insulator to be measured and paid seperately).

M&L galvanised stay strand 7/2.24mm size complete all as specified & directed by engr in charge

S&F LT 1100V pin type porcelain/ vitreous china, white, brown, or green insulator hight 100 mm, 65mm dia, 1100 V grade incl. one galvanised mild steel spindle, two galvanised iron washer and one GI nut complete [ISI marked]. Make : BHEL, Modern.

S&F LT 1100V shackle type porcelain/ vitreous white, 75mm height 90mm dia incl. one galvanised mild steel spindle, washer insulator bolt & GI nut complete [ISI marked]. Make : BHEL, Modern.

M&L PCC 1:4:8 type D-2 using 40mm grade stone aggregate in foundation of pole, complete all as specified and directed.

M&L PCC 1:3:6 type C-2 using 40mm grade stone aggregate in foundation of stay, complete all as specified and directed.

M&L PCC 1:3:6 type C-1 using 20mm grade stone aggregate for pole / stay assy incl necessary form work & finishing concrete surface even & smooth without using extra cement, complete all as specified and directed.

Dismantling cross-arms of M.S. channel or angle sections etc. complete and setting aside for re-use with in 50m, complete all as specified and directed.

M&L in repair cross arm , bracing support MS clamps etc including necessary fabrication, bolts, nuts, washers etc and painting with one coat of red oxide and two coats of aluminium paints, complete all as specified and directed.

Supply and replace power Capacitor 440volts,Heavy duty 3 Kvar with suitable cable connection, complete all as specified and directed. Make TDK/Epcos/HavellsL&T

Supply and replace power Capacitor 440volts,Heavy duty 5 Kvar with suitable cable connection. Make TDK/Epcos/Havells/L&T

Supply and replace power Capacitor 440volts,Heavy duty 10 Kvar with suitable cable connection, complete all as specified and directed. Make TDK/Epcos/Havells/L&T

S&F spacer 2 wire system in LT over head line in position / location.

S&F spacer 4 wire system in LT over head line in position / location.

M&L for painting of PCC LT poles in Zebra pattern 30 cm wide, with synthentic enamelled paint in black and white colour up to 1.2 metre height from pedestal, including writing in 80 mm wide letters/ numberss in both side of pole MES, LT and pole No, complete all as specified and directed.

M&L for re-stretching ACSR conductor on LT pole having (4+2) conductors of any type including using new binding wire, complete all as specified and directed.

M&L for re-stretching ACSR conductor on LT pole having (4) conductors of any type including using new binding wire, complete all as specified and directed.

M&L for re-stretching ACSR conductor on LT pole having (2) conductors of any type including using new binding wire, complete all as specified and directed.

S&F junction box made from SMC/FRP sheet ready made of size 300 x 200 x 105 mm with aluminium bus bar of 100 Amp capacity for RYB and neutral made in suitbale size fixed inside the junction box with necessary supporting insulators fixed on hylem sheet fixed to pole /Wall with MS clamp 20 X 3 mm and nuts & bolts, MCB SP 6 Amp 10 KA 240 V - 1 No and aluminum lugs for connecting cables, complete all as specified and directed.

M&L in replacement of galvanised steel wire 4mm dia as earth conductor run along the over head line duly binded with metallic cross arms and armour of cable at the end pole, complete all as specified and directed.

Taking down one old u/s existing feeder piller box and Supply, installation, testing and commissioning CPRI approved Make LT panel wall mounted cubical canopy type, outdoor dust and vermin proof made out of CRCA sheet 3.15 mm thick steet sheel and 40x40x6 mm angle iron section with hinged cubical doors front side openable having locking arrangements and all accessories complete as per IE rule with powder coated paint over one coat of red oxide primer complete with required fixing arrangements etc and all accessories incl necessary PCC (1 : 3 : 6) type C2 as in foundation all as directed, comprising of the following :- Incoming :- (i) 250 Amp MCCB 4 Pole, 36KA - 01 No. Make - Havells, (ii) Aluminium Bus Bar 400 Amps 4 way (iii) Digital type Ameter , range 0 to 400 Amp with slector switch and CT Make : AE (iv) Digital type Volt meter, range 0 to 500 Volt with slector switch and PT. Make : AE (v) Indicator lamp RYB LED. Outgoing :- (i) 100 Amp MCCB 4 Pole, 25KA - 2 No. Make - Havells, (ii) 63 Amp MCCB 4 Pole, 25KA - 1 No. Make - Havells (ii) 63 Amp MCCB 4 Pole, 25KA - 1 No. Make - Havells (vi) MCB TPN 63 Amps 25 KA Make - Legrand (viii) 3.15 mm thick CRCA Sheet and angle iron 40 X 40 X 6 mm frame (ix) Timer controll unit with all accessories - 01 No

S&F LT feeder piller box 3.15 mm thick out door type, CPRI approved with 600 Amp Aluminium bus bar for RYB and half for neutral with necessary control wiring Ammeter , Volt mer, Indicating lamp and CT's comple following :- Incomming :- (a) MCCB 400 Amp,4 pole 25 KA - 01 Nos ( As incoming) (b) Digital Volt Meter 0-500 Volt - 01 Nos (c) LED type Indicating lamps -03 Nos Outgoing :- (a) MCCB 200 Amp ,4 pole 16 KA - 01 Nos (b) MCCB 125 Amp ,4 pole 16 KA - 01 Nos (c) MCCB 63 Amp ,4 pole 16 KA - 01 Nos (d) MCCB 36 Amp ,4 pole 16 KA - 01 Nos (e) Digital Ammeter 0 - 500 Amp -01 Nos (f) CT's 500 /5 Amp - Set of three

M/S Anjan Kumar Singh

M/S AJAY KUMAR SINGH