SPL REP TO BLDG NO. P-19 (OFFICE COMPLEX) OF 665 AVN AND AFFILIATED FLTS AND PROVN OF TECH STORE FOR STORAGE OF EQPT/STORES OF UAV AT CATS AND PROVN OF SHED FIVE PARKING SLOTS IN FRONT OF BLDG NO.P-100, MAIN OFFICE OF 201 ARMY AVN SQN UNDER GE NASIK

Amount

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard soil complete all as specified and as directed.

Excavating in post holes (or similar holes) each n exc 0.5 filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in hard and dense soil complete all as specified and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep soft /loose soil and getting out

Returning, filling in including spreading, levelling watering and well ramming in layers not exceeding 25cm in hard and dense soil complete all as specified and directed.

Removing excavated material to a distance exc 50m n.exc 250m and depositing where directed at a level n.exc 1.5m above the starting point.complete all as specified and directed.

Removing excavated material (soil) to a distance not exceeding 50 m and depositing where directed at a level n exc 1.5m above the starting point complete all as directed.

M&L for hardcore of broken stone of gauge n.exc 63 mm deposited spread and levelled in layer n.exc 15 cm thick and watered and rammed to a true surface etc complete all as specified and as directed.

M&L for 75 mm thick Plain Cement concrete type D- 2, 1:4:8 (40mm graded aggregate)as in sub bases to floor.

M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand.

Dismentling of single layer Manglore pattern or similar tiles in roofing

Dismantling CGI corrugated and plain sheets in wall cladding or roof coverings including ridges and make good of aluminium earthing strips after fixing of sheets (at any height / any location) complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description and in any position complete all as directed by Engr-in-Charge.

Dismantling framed wooden trusses span n exc 10 m of any description and in any position complete all as directed by Engr-in-Charge.

Dismantling timber scantling in fillets, rails, posts, rafters, purlins etc. under 40 Sqcm in section framed work complete all as specified and directed.

Dismantling boarding any description fixed in any postion with nails complete all as specified and directed.

Dismantling wall ceiling boards (fibre, pulp, insulation etc) or insulation boards/slab/blankets including cover fillets, GI/aluminium gride etc.complete all as specified and directed.

S&F roof trusses (framed), trussed, purlins, rafters, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats Fe-410-W (Gde E-250) Quality -A all as specified and directed.

S&F Rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc. complete all as specified and directed.confarming Fe 410W (Gde E-250 quality A)

S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes,with riveted, bolted or welded attachment conforming to Fe 410-W (Gde-E 250) quality-A etc.

ReFixing and erection fixing old any thickness/size of rolled MS section as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates complete all as specified and directed. Note :- Old dismenatled steel under Item No.13.00 shall be used for this item.

S&F 12mm mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other end, each screwed end to be fitted with washers and one hexagonal or square nut n exc 5cm long .

S&F 12mm mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other end, each screwed end to be fitted with washers and one hexagonal or square nut exc 5cm n exc 10 cm long .

S&F Steel work in tubular trusses,purlins including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete fabrication and erection at site as per drgs.

M&L for PCC 1:4:8 type D-2(using 40 mm graded stone aggt) as in foundations, filling and mass concrete

M&L for Plain Cement concrete 1:2:4 type B-2(using 40 mm graded aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

M&L for providing, cement concrete Type B0 1:2:4 in parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates including necessory formwork etc. completed.

M&L for TMT bars 10mm dia and over cut to length bent to shape required including cranking bending spirally for hopping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0,9 mm dia or securing with clips quality confiring to Fe-410 complete all as specified and directed.

All as per item No. 28.00 but 5mm dia and over upto and incuding 10mm dia in stirrups tie, spacers and binder complete all as specified and directed.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other end, each screwed end to be fitted with washers and one hexagonal or square nut exc 10cm but n exc 15cm long and dia of neck is 11 to 15mm.

M&L for form work to sides of concrete foundations,footings bases of coloumns raft and raft beams,sides and soffits (if any) of foundation and plinth beams, and similar work,vertical or to batter for rough finished surface of concrete complete all as specified and directed.

M&L for RCC M-25 design mix (using 20mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams, bases fo columns, etc,basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for form work to sides of pillars, posts,struts,piers,columns etc or to batter for rough finished surface of concrete complete all as specified and directed.

M&L for RCC M-25 design mix (using 20mm graded stone aggregate) as in columns, pillars piers, posts and struts complete all as specified and directed.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.

M&L for RCC M-25 design mix (using 20mm graded stone aggregate) lintel beams, roof beams, cantilevers ,chajjas bressumers, lintels over 1.5m span complete all as specified and directed.

M&L for formwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed.

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (Horizontal or sloping)

M&L for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide.

M&L for M-25 design mix(using 20mm graded stone aggregate) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified

S&F repair MS sheet 1.60 mm thick plain black in steel gates and similar works, cut to size ,holes punched including round headed screws, revets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up,mitred angles etc as required.

Supply and fixing position suspended false ceiling system using T-grid suspended ceiling grid system . The size of grid shall be 600x600mm with GI frame work main runner 38x24x3600mm, cross tee 25x24x600mm/ 25x24x1200mm and wall angle 24x24x2540mm( thickness of the materail of 0.30mm). using 9mm thick ceiling panel laminated with PVC film on front face and foil back available in the drop texture as per IS-2095, part-I 1996, fixed in the grid of T-grid suspended ceiling grid system duly susupended by 4mm dia GI bar hanged from the purlins of the roof with butter fly clips complete all as specified and directed by Engr-in-Charge.

M&L for Preparing new steel surfaces of any description exc 10cm width or grith and applying two coat of synthetic enamel paint over a coat of red oxide complete.

M&L for Preparing old steel surfaces of any description exc 10cm width or grith and applying one coat of synthetic enamel paint over a coat of red oxide complete.

M&L for Two coat of synthetic enamel paint over a coat of red oxide primer including preparation of steel surfaces of any description, not otherwise described, not exceeding 10 cm in width or girth, complete all as specified.

Demolition brickwork or stone/boulder masonry, built in cement morta including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articlesbuilt in cement mortar of any description.

M&L for Brick work with fly ash bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for rendering 10 mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished fair & even.

M&L for 5 mm thick rendering on ceiling surfaces finished fair & even.

M&L for rendering 15 mm thick on fair faces of brickwork or concrete surfaces in CM 1:4.Plaster to be done in two coats(10mm+5mm) final coat with wpc(paid searately) as specified.

M&L for 18 to 20mm thick Granite (Telephonic black/Ruby red) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite 18 to 20mm thick. over and including different type shade/colour all as specified and directed.

M&L for moorum filling under floors or paving laid in layers n.exc 15cm thick, spread, levelled and rammed including watering complete all as specified and directed. (Note. Moorum to be broght from outside MoD land.)

M&L for Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured)

M&L for Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface

M&L for stone walling of polygonal rubble, uncoursed well bonded, beded solidly hearted built in cement mortar 1:6 including 20mm hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses complete.

M&L for coloured ceramic tile 7-8 mm thick are exe 0.11 sqm but nexc 0.36 sqm as in flooring over and including 15mm thick cement mortar screed bed in CM 1:6 for laying floor in any shape/position. Note : - Size of tile as approved by GE.

All as per Item No. 58.00 above but 10mm thick cement mortar as in back coat in CM 1:4 for skirting etc in any shape/position.

Taking down shutters of any description exc 1sq.m and n exc 2 sqm each complete all as specified and as directed.

Taking down chowkhats or frame with shutter n exc 1.50 sqm each complete all as specified and as directed.

Taking down chowkhats or frame with shutter exc 1.50 sqm but n exc 4 sqm each complete all as specified and as directed.

S&F Anodised aluminium(minimum 50 micron powder coated) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

M&L for aluminium (minimum 50 micron powder coated) door shutters, aluminium section weighing 0.55 kg / m including necessary joining cleats, glazing clips, rubber neoprene packing, handles and tower bolt 150 mm long 2 Nos in each door, hinges,anodised aluminium snap beading screw etc. complete all as specified.

M&L for aluminium (minimum 50 micron powder coated) window and ventilator shutters, side hung / sliding type without sash bars, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminum fitting such as peg stays / tower bolt 150 mm long (1 No) hinges type B- 21, 100mm long (2 Nos), suitable handle (1No), rollers . grip etc. complete all as spicifed.

S&F in repairs brass Mortice lock, vertical type, 4 levers, size 100 mm suitable for aluminum doors complete all as specified.

M&L for 4.8mm thick sheet glass ordinary quality and glazing with oil putty or wooden beading in squares n. exc 0.5 sqm in each pane including making good to desturbed surace matching with existing surface complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and avg width of aperture 1.40mm and fixed with and incl nut and bolts or wooden fillets to steel, wooden, aluminium windows/ventilator and wooden doors etc complete all as specified and directed.

S&F Door closer hydraulically regulated,cast iron body designation No-3 universal type, suitable for door shutter of 851 to 1000 mm in width & of weight between 61 to 80 Kg

M&L for taking down cement of cement lime plaster of any description on brick or stone walls etc including ranking out joints hacking for key scrubbing down with water etc complete all as specified and as directed by the Engineer-in-Charge.

M&L for rendering 12mm thick on fair faces of brick work or concrete surfaces in CM (1:6) finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparing of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed by the Engineer-in-charge

M&L for 3mm thick wall care putty on wall.

M&L for preparation new plastered surfaces of ceiling and applying two coats of distemper oil emulsion over a coat of acylic primer over a coat of putty complete all as specified and directed.

M&L for preparation of newly plastered surfaces two coats of exterior emulsion paint over a coats of primer including preparation of surfaces complete all as specified and directed by Engr-in-charge.

M&L for Rounding to edges of stone slabs one edge, such as in steps,cooking platform and other similar work.

Supplying only integral water proofing compound ISI marked complete all as specified and as directed.

S&F Butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, type B-12,size 125 mm

M&L for complete removal of existing treatment by wire brushing, rubbing down with water and preparing of old treated surfaces of walls and applying two coats of oil bound distemper (oil emulsion) over a coat of primer by roller brush including cleaning all window panes from splashes/droppings, etc complete all as specified and as directed by the Engineer-in-charge

S&F Framed work such as grills, gratings(Ornamental and intricate design), etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

M&L for Waterproofing on roof including flashing and junctions of parapet,kerb, wall etc.as under :- (a) Laying a layer of APP based polymeric membrane,3 mm thick(minimum),weighing not less than 3.60 kg/Sqm prefabricated fire layer waterproofing membrane reinforced with polyester non woven fabric(weighing not less than 160 gms/sqm) shall be applied over compatible primer(oil based) at 0.40 litre/Sqm of density at 25 degree Centigrade 0.87-0.89 Kg /Litre and viscosity 70-160cps or cold sticker, application of APP modified membrance shall be by torch application. The overlaps shall be minimum 150mm on the transverse direction and 100 mm on the longitudinal direction. (b) APP membrance,Primer and bitumastic aluminium paint shall be of same brand. (c) Bitumen and aluminium paint shall be paid separately.

M&L for Applying evenly a coat of hot blown bitumen 85/25 over roof surface,facia,parapet etc at the rate of 1.2 kg per sqm for fixing app membrane etc including cleaning surfaces.

M&L for applying two coats of solar reflective bitumastic aluminium paint at the rate 0.15kg/sqm per two coats over exposed app membrane surfaces(old/new) including preparation of surfaces to the entire satisfaction of ground executives.

S&F 200mm size aluminium anodised,barrel tower bolts of extruded section and fixed.

S&F 300 mm size aluminium alloy,anodised,sliding door bolt with hasp,staple(bolt type) and fixing clips of sheet,cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy and fixed.

M&L for keyed pointing to random or polygonal rubble, uncoursed or brought upto course in cement mortar 1:4 etc complete all as specified and as directed by the Engineer-in-Charge.

M&L for Preparing old painted brick, stone, concrete, asbestos cement or plaster surfaces of any description over 10cm girth or width, not otherwise described and one coats of synthetic enamel paint in one or more pattern etc

S&F 4mm thick Sheet glass,ordinary quality and glazing with oil putty in square but exc 0.5 sqm in each pane

S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.00mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

M&L for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 65x125 mm(Double rebated) comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

M&L for Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moistureproof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer -In- Charge.

M&L for Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter (with provision of fixing mosquitto proofing in decorative fashion) of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moistureproof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer -In- Charge.

Supply, fixing and laying of in trenches or fixing or passing through pipe, 1100 Volts grade heavy duty LT UG cable, 4 core 10 Sqmm, with XLPE insulated stranded Aluminium conductor served with an inner sheathing of PVC tape, Armoured with galvanised steel wire and overall sheathed including cable gland, lugs, jointing material etc, jointing, connecting, testing and commissioning all as specified and directed.

M&L for Double Walled Corrugated DWC HDPE Pipe of outer dia 50mm and innter dia 38mm including 90 degree bends with coupler and rubber ring laid in trenches of size 50 mm suitable for cable protection of size 2 core 10 sqmm to 3.5 core 50 sqmm cable complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors, etc.

Taking down fan, sealing cable end,dismantling blades and removing fan and blades to store

Dismantling unserviceable main switch/DBs with MCBs and wooden board including making good disturbed surface of wall.

Taking down sub main wiring of any size/capacity complete all as specified and making good disturbed sufaces to match with the existing surfaces.

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan Hanging only cconnector to fan. Note : Fans taken down from Item No. 96.00 will be issued under free for fixing.

M&L for point wiring with 1.5 Sqmm (22/0.30mm) PVC insulated and unsheathed multistranded copper conductor cable, 1100 volts grade, ISI marked, FRLS type drawn through and including PVC concealed conduit (ISI marked) of adequate size and its accessories with sunk cast iron/pressed steel terminal boxes of size 1.2mm thick, with 3mm thick plastic laminated sheet cover of adequate size for one light or one fan point controlled by one switch incl 1.5 Sqmm (nominal area) copper conductor cable (multistrand), FRLS type, PVC insulated and unsheathed with colour code earth wire connected to common earth dolly at one end and metalic bodies of luminaires/ fan at other end complete all as specified and directed for One light point/ fan point controlled by one, one way swtich. Note:- Unit rate include for cutting chases for conduits and sinking for boxes and making good to wall, floors etc.

All as per ser item No. 100.00 herein before but One 5 Amp 5 pin socket outlet point on same board with other switches including earth wire as specified.

All as per ser item No. 100.00 herein before but with 4.0 Sqmm (36/0.30mm) PVC copper stranded cable FRLS type for one 15 Amp 6 pin socket outlet point including PVC cable 4 Sqmm FRLS type copper stranded conductor as earth wire as specified & connected to commen earth & earth terminals including boards for mounting purposes.

All as per ser item No. 100.00 herein before but on independent board.

Supply and fixing of switch piano flush button 5 Amp single pole one way 230 volts white finish all as specified & directed.

Supply and fixing of socket outlet flush type 5 pin 5 Amp multipurpose 230 volts single pole one way suitable for 3 pin/2pin 5 Amp plug top white/ivory finish all as specified & directed.

Supply and fixing of switch socket combination flush type 3 pin 5 Amp multipurpose 230 volts single pole one way suitable for 3 pin/2pin 5 Amp plug top white/ivory finish all as specified & directed.

Supply and fixing of switch socket combination multipurpose flush type 2 in 1 type (3 and 3 pin) 5/15 Amps, 230V, AC.

Supply and fix of ceiling rose surface PVC 50mm dia 3 terminals including PVC mounting block white/ivory finish.

M&L for Point wiring with PVC insulated unsheathed stranded copper conductor cable of size 1.5 Sqmm, with PVC insulated unsheathed stranded copper conductor cable of size 1.5 Sqmm stranded for earth continuity wire, to be drawn in and including, PVC medium grade surface casing capping not less then 20 mm width with MS sheet metal sunken switch/Terminal box/MODULAR METAL/PVC FLUSH BOX 1.2 mm thick and ebonite switch board cover 3.0 mm thick or PVC moulded switch board and brass screws with cup washers including all necessary wall cutting and making good disturbed surface all as directed and specified for the One light point controlled by one, one way switch. Note : Cutting chases and making good to match with the adjoining surface shall be included in the unit rate.

All as per ser item No. 109.00 herein before but One ceiling /exhaust fan point controlled by one switch and regulator

All as per ser item No. 109.00 herein before but One 3 pin 5 amp socket outlet point on the same board with other switches.

All as per ser item No. 109.00 herein before but One 3 pin 5 amps socket outlet point on independent board

All as per ser item No. 109.00 herein before but One bell/buzzer point controlled by one bell push.

All as per ser item No. 109.00 herein before but One light point controlled by two 2-way switches, with cables 1.5 sq. mm size

All as per ser item No. 109.00 herein before but for one socket outlet 15 amp on independent board with 2.5 Sq. mm cable and 2.5 Sq.mm earth wire.

Supply and fixing Modular switch 1 way 6A, 1 module, ISI marked complete all as specifed and directed by Engineer in Charge.

Supply and fixing Modular switch 2 way 6A, 1 module ISI marked complete all as specifed and directed by Engineer in Charge.

Supply and fixing modular Socket, 6A - 2/3 pin combined 2 module, ISI marked complete all as specifed and directed by Engineer in Charge.

Supply and fixing Modular Bell push 6A 1 module ISI marked complete all as specifed and directed by Engineer in Charge.

Supply and fixing Modular switch 1 way 16A, 1 module ISI marked complete all as specifed and directed by Engineer in Charge.

Supply and fixing Modular Socket 6A/16A - 2/3 pin combined 2 module ISI marked complete all as specifed and directed by Engineer in Charge.

Supply and fixing White cover plate with frame, 1 module ISI marked complete all as specifed and directed by Engineer in Charge.

Supply and fixing White cover plate with frame, 3 module ISI marked complete all as specifed and directed by Engineer in Charge.

Supply and fixing White cover plate with frame, 4 module ISI marked complete all as specifed and directed by Engineer in Charge.

Supply and fixing White cover plate with frame, 6 module ISI marked complete all as specifed and directed by Engineer in Charge.

Supply and fixing Buzzer, Ding Dong AC. 230 volts, single pole ISI marked complete all as specifed and directed by Engineer in Charge.

Supply and fixing Modular Fan step regulator, 120W - 2 module ISI marked complete all as specifed and directed by Engineer in Charge.

Supply and fixing and connecting up fan regulator electronic on existing phenolic laminated sheet dimmer type 230 volts, 450 watts suitable for ceiling fan 1200/1400mm sweep.

Supply and fixing Ceiling fan complete with blades, down rod electronic regulator and accessories 230 volts, 1200mm sweep, min air delivery 210 CFM with service value 6 BEE five star eated with brushless direct current motor (BLDC) complete including using 1.5 Sqmm FRLS PVC insulated (Unsheathed) 3 core copper conductor cable, 1100V grade complete all as specified and directed.

Supply and fixing exhaust fan complete with blades, steel body AC single phase 230 volts, 380mm sweep, with service value 6 BEE five star rated complete including using 1.5 Sqmm FRLS PVC insulated (Unsheathed) 3 core copper conductor cable, 1100V grade complete all as specified and directed.

Supply and fix in replacement of SP&N enclosure with 2 pole and earth metal plug & socket for incorporating 10 A / 20 A SPN / DP MCB complete all as specified and directed.

Supply and fixing in replacement of LED 20 Watt inverter LED batten with rod complete with lithium ion battery with charging time 8-10 hours and backup time upto 4 hours mounted on square box of suitable size connecting up with three core flexible copper conductor cable of suitable size from ceiling rose.

Supply and fixing of 30 Watt invertor LED street light fitting luminaire, energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedded PC cover having Bottom Opening seperate driver compartment with IP66 protection and impact resistance of IK08. , including coneecting up with 2/3 core flexible coppper conductor cable , compete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of invertor LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

Supply and fixing in replacement of invertor LED luminaire round shape 15 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete.

M&L for sub main wiring power/circuit using PVC insulated unsheathed, stranded copper conductor cable 2 Single core of size 2.5 Sqmm, earth continuity conductor of size 2.5 Sqmm to be drawn through and including PVC CASING CAPING not less then 20mm width medium Grade fixed on walls/roof/floors all as directed by Engineer in Charge. Notes:- Two wires of 2.5 sqmm and one wire of 2.5 sqmm for earthing and one run of PVC casing/caping shall be measured as one unit.

M&L for sub main wiring power/circuit using PVC insulated unsheathed, stranded copper conductor cable 2 Single core of size 4 Sqmm, earth continuity conductor of size 4 Sqmm to be drawn through and including PVC casing capping not less then 32mm width medium Grade fixed on walls/roof/floors all as directed by Engineer in Charge. Notes:- Two wires of 4 sqmm and one wire of 4 sqmm for earthing and one run of PVC casing capping shall be measured as one unit.

M&L for sub main wiring power/circuit using PVC insulated unsheathed, stranded copper conductor cable 2 Single core of size 6 Sqmm, earth continuity conductor of size 6 Sqmm to be drawn through and including PVC CASING CAPPING not less then 32mm width medium Grade fixed on walls/roof/floors all as directed by Engineer in Charge. Notes:- Two wires of 6 sqmm and one wire of 6 sqmm and one run of PVC casing capping shall be measured as one unit.

S&F in replacement of Sheet metal enclosure factory made for DBs single pole and neutral double door 240 volts 12 way with 200 Amps rated bus bar fixed on walls, including dressing and connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning and making good of wall, surfaces all as specified and directed.

S&F in replacement of Sheet metal enclosure factory made for DBs single pole and neutral double door 240 volts 8 way with 200 Amps rated bus bar fixed on walls, including dressing and connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning and making good of wall, surfaces all as specified and directed.

Supply and fixing in replacement of MCB, single pole and neutral, 240 Volts, 6-32 Amps all as specified and as directed.

Supply and fixing of MCB SP 6-32 Amps, 230 Volts, 50 Hz with 10 KA.

Supply and fixing MCB TP 40 Amp, 415 Volts, 50 Hz with 10 KA.

Supply and fixing in replacement of MCB single pole 240 Volts, 6 to 32 Amps all as specified and as directed.

Supply and fixing in replacement of invertor LED bulkhead 10 watt 220 volts AC with high efficacy PMMA diffuser soft glare free light complete with drivers, clamps complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size.

M&L for in replacement of MS box of size 160x120x30 cm depth, dust proof with front opening hinged door both side, made out of 2mm thick MS sheet cubical type with powder coated painting for mounting of MCCB, DB's, electric meter etc inside the box fixed in wall by necessary cutting of wall of suitable size in concealled and making good the surface, by applying cement work, brick work and matching colour (Oil bond distemper) etc including dismantling of MS box with MCCB DB's and electric meters and refixing the same MCCB, DB's and electric meters in new box carefully including necessary electric connection by suitable size of copper conductor cable of suitable length and testing completed all as directed by Engr-in-Charge. Note : (a) Any plastering work involved while taking out old UNSV meter box and refixing the new meter box is deem to be included in this rate. (b) PVC flexible conduit required within the meter boxes is deemed to be included in this item rates.

Supply and fixing in replacement of invertor LED luminaire 600 x 600mm, 36 watt, 220 volts, 3000K AC recessed/ surface type fittings, IP 20 with battery backup and tri-colour CCT with remote control, epoxy powder coated CRCA sheet housing with electronic driver, connector block, etc. complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size.

Supply and fixing in replacement of 30 Watt invertor LED street light fitting luminaire, energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedded PC cover having Bottom Opening seperate driver compartment with IP66 protection and impact resistance of IK08. , including coneecting up with 2/3 core flexible coppper conductor cable, compete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement sheet metal enclosure (factory made), TPN Vertical Distribution Boards (MCCB Incomer) IP43 protection Double Door : Plain 8 way with 200 Amps rated busbar all as specified and directed.

Supply and fixing in replacement 4 Pole MCCB 125 Amp, 50 Hz, 415 Volt, with adjustable thermal & adjustable magnetic setting, breaking capacity 25 KA.

M&L for Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6.3 mm thickness burried directly in ground (earth pit not less than 2.25mtr deep below normal ground level) with top edge of earth plate not less than 1.5 mtr below normal ground level connected to and incl galvanised earth lead wire of 4.00mm dia by means of nuts & bolts, check nuts and washers of galvanised incl PCC pit of 1:2:4 type B-1, cover reinforced with XPM weight not less than 4 Kg/Sqm and 6mm dia bar handle, earth pit angle iron frame of size 25mm x 25mm, excavation and earth work in any type of soil, charcoal dust, salt, light grade GI watering pipe 20mm dia with funnel and wire -mesh and medium grade GI protection pipe of 15mm bore from top edge of earth plate upto main distribution board complete all to as shown in electrical plate No 3 of MES Sch 2009 (Part I) connected main switch board all as specified and testing on completion.

NOTE : - AMOUNT OF SCHEDULE OF CREDIT RS. 73,319.00 WILL BE DEDUCTED FROM TOTAL AMOUNT OF BOQ.

J Sams Contructions (BID ID -3157244)

Abhiraj Enterprises (BID ID -3154188)

Bidder Name

M/S SAMEER SUBHASH PATANI

J Sams Contructions

Abhiraj Enterprises