Certain repairs to Fencing, Gates, Boundary Wall, traverse wall, Hardstanding, Drain, Path and connected miscellaneous works at Mil Stn Suranussi under AGE (I) Suranussi.

Amount

Demolition of brick work built in cement mortar including all quoins, arches, pillars etc but including ashlar facings dressed stone work and pre cast concrete articles complete all as specified and as directed by the Engineer-in-Charge.

Demolition of cement concrete in ground floor and pavings not exceeding 15 cm thick above or below ground level.

Material and labour for brick work built in cement mortar (1: 6) with sub class ‘B’ bricks, straight or curved on plan exc 6 m mean radius, using old size bricks complete all as specified and as directed by the Engineer-in-Charge.

-ditto- as per item No 3 above except Brick complete all as specified and as directed by the Engineer-in-Charge.

M&L for brick work sub class 'B' bricks laid flat bedded and jointed in CM (1:6) and pointed in CM (1:3) complete all as specified and as directed by the Engineer-in-Charge.

-ditto- but laid on edges complete all as specified and as directed by the Engineer-in-Charge.

Taking down cement plaster of any description on brick or stone wall as in boundary wall etc, including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified & directed by the Engineer in Charge.

Material and labour for rendering 15 mm thick cement plaster in cement mortar (1:4) of brick / concrete surfaces finished the surfaces even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of new surfaces of walls including cornices, pilasters etc (Plastered or un plastered surfaces) and applying two of coats of cement base paint over a coat of alkali primer complete all as specified & directed by the Engineer in Charge.

Material and labour for plain cement concrete (1:3:6), type C-2 using 40mm graded crushed stone aggregate, as in surface channel complete all as specified and directed by the Engineer-in-Charge.

M&L for 40 mm thick PCC 1:2:4 type B1 (using 20mm graded aggregate) as in flooring incl finishing the surface even and smooth with using extra cement

M&L 75 mm thick PCC type D 2 1:4:8 over well rammed earth as in sub base complete all as specified and directed by the Engineer-in-Charge.

M & L 100 mm thick Cement concrete type D- 2, 1:4:8 (40mm graded aggregate) as in PCC Floor and paving complete all as specified and directed by Engr - in - Charge.

M&L 25 mm thick Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed by Engineer-in–Charge.

M & L Machine pressed precast conc. interlocking paver block (rectangulat/star etc.) (Red/yellow)any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 grade with grey cement and with pigment complete all as specified and directed by Engr - in - Charge.

M & L Machine pressed precast conc. interlocking paver block any shape (rectangulat/star with PU coating etc.) (Red/yellow)any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 grade with grey cement and with pigment complete all as specified and directed by Engr - in - Charge.

M & L Providing precast cement concrete type B-1 1:2:4 (Set in cement mortar 1:4)( 20 mm graded stone aggregate ) as in kerbstone including chamfers weatherings , throating etc. complete all as specified and directed by Engineer -in charge.

M & L Providing Precast Cement Concrete M-25 (Nominal Mix )( 20 mm graded stone aggregate ) as in kerbstone including chamfers weatherings ,throating etc. with design as required Red/Green colour blinking lights size (300x300x150mm )complete all as specified and directed by Engineer -in charge.

M&L for preparation of new surfaces of wall and apply two coats of plastic emulsion paint over 10cm width or girth over a proming paint plaster coat incl preparation of surfaces complete all as specified

M & L Cement concrete 1:2:4 type B–1 using 20mm graded stone aggregates in copings,, including weathering, slightly rounded or chamfered angles and throating, as directed all as specified and directed by Engineer - in - Charge .

Dismantling of galvanised mild steel barbed wire of any description from fencing post (RCC/ Steel) complete all as specified and as directed by Engineer-in-Charge.

Supply and fix in repairs galvanised 2 strand steel barbed wire 2.24 mm dia , barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossing with and provision of galvanised mild steel wire, staple or steel pins etc complete all as specified and directed by Engr-in-Charge. (Each line wire to be measured)

All as per Item No 22 above here-in-before but restraining re-securing including making good staples etc. complete all as specified and directed by Engr-in-Charge. (Each line wire to be measured)

M & L 75 mm thick Cement concrete type D-2, 1:4:8 ( (40mm graded aggregate) as in sub Bases complete all as specified and directed by Engr - in - Charge.

M&L for Screed bed or bedding layer of mortar 20 mm thick in CM 1:6 for laying floor finishes complete all as specified.

M & L for chequered cement concrete tiles 30cm x 30cm x 25mm thick set, jointed and pointed in neat cement slurry and pigments as in floors complete all as specified and directed by Engineer - in - Charge .

Material and labour for mild steel round bars 10mm dia Fe-410-W (Gde.E-250) quality-A or Fe 290 (Gde -E-165) as in reinforcement cut to length, bent to shape including cranking bending, and binding with MS wire (annealed) not less than 0.9 mm dia complete all as specified and as directed by Engineer-in-charge.

M&L providing precast cement concrete louvres and jallies, with RCC post 50 mm thick (measured solid), type B-0(1:2:4) using 12.5mm graded aggregate including all mould- ings but excluding frame set in cement mortar 1:4 complete all as specified and directed by Engr-In-Charge.

Dismantling wooden boarding, any description, fixed in any position with nails complete all as specified and directed by Engineer-in Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), rmoving servicable tiles to store and rubbish off the premises.

M&L Granite (of any type) work (table rubbed and polished) 20 mm thick in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over screed or bedding layer in CM 1:4 all as specified and directed by Engineer-in Charge.

M&L for Non - skid joint free coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) (Garbage bin ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match , over15 mm th screed or bedding layer in CM 1:6 complete all as specified and directed by Engineer-in Charge.

M&L for glazed ceramic tiles coloured of size 300mmx200mm x 7mm th on vertical surfaces such as in skirting, dado etc over 10 mm th backing coat in cm 1:4 complete all as specified and directed by Engineer-in Charge.

S & F reflective HIP cautionary circular sign board of size 600 mm made of ACP sheet 3 mm thick supported over 25x25x3 mm MS angle iron frame powder coated with hold fast.front side of the sign board fully reflective with high intensity reflective sheet base letter ,sign and border duty computer cut.sign board supported over single leg of 47 mm MS square pipe of 3 mtr long duly painted black and white incl exc in post holes each n.exc 0.50 cum and removing surplus soil n .exc 50m and making good surface in loose/soft soil filling with cement concrete type B1 1:2:4 (40 mm graded agg ) as in foundation filling and mass concrete complete all as specified and as directed

Supply and fixing informatory sign board of made of aluminium sheet 2 mm thick with stainless steel rectangular frame using 25 x 15 mm rectangular pipe with 35 mm dia stainless pipe in outer border all around retro reflective high intensity 400 micron thick any colour sheet pasted with heating process on both sides of the board including 75 mm to 100 mm high black colour letters cut to shape with special plotter and in proper manner incidating Shed No as directed by Engr in charge .02 Nos 75 mm dia stainless steel pipes of 304 grade glossy finish with MS plate 3 mm thick welded at bottom of pipes shall be provided the board shall be fixed at height of 6.0 mm (top level of board) above GL and shall be embedded in ground using PCC 1:2:4 type B-1 of min size 300mmx300mmx600mm including necessary from work.excavartion and earth work complete all as specified and directed.

Dismantling fencing wire mesh, any type complete all as specified and as directed by the Engineer-in-Charge.

Fixing of chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed by Engr-in-charge

Supply only Chain link fencing made out of plain mild steel galvinised wire , width of aperature 100 mm x 100 mm x 4mm dia to new steel posts by means of nuts and bolts, complete all as specified and directed by Engineer - in – Charge

Dismantling posts or struts embedded (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground

S&F for Mild steel angle iron fencing post and sturts in fencing incl necessary cutting drilling welding etc and bending to swan neck shape as required and drilling holes notching for wives etc conforming to Fe-290 Gde E-165 complete all as specified.

M&L Plain Cement concrete 1:3:6 type C-2 (using 40mm graded aggregate) as in foundations, filling and mass concrete complete all as specified and directed by Engineer-in Charge.

S&F MS Flat iron for securing bolts post and strut in fencing including cutting drilling holes notching for wire etc. flat iron filet and similar work conforming to FE 410-0 or Fe 310-0 complete all as specified

S&F mild steel screw bolts 12mm dia(machine made) with hexagonal or square heads at one end and screwed the other , or screwed both ends , each screwed end to be fitted with washers and one hexagonal or square nut, exc 10 cm but n. exc. 15 cm long and dia of shank 5 to 10 mm complete all as specified and directed.

M&L applying two coats of synthetic enamel paint over a coat of red oxide 0r zinc chromate primer including preparation of new steel or iron surfaces exc 10 cm width or girth, complete all as specified and directed.

M&L for preparation of new steel surfaces n exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specifed and directed.

Material & Labour for providing and fixing stainless steel (Grade 304) railing/gate made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement.

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering to Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening conforming to GdeFe 290(Gde E-165) complete all as specified and as directed

Taking down chowkats or frames with Shutters ( without taking off the shutter from the frame ) of area n.exc 1.50 Sqm each and removing from site complete all as specified and as directed

S & F 1 mm thick mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required

S & F 2 mm thick Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc. including dismantling and taking down old unserviceable PVC sheets completed all as specified

DUGGAL CONSTRUCTION CO

SONA BUILDERS

Motorway Constructions