REPAIR TO E/M INSTALLATION AT MIL STN KALKA UNDER GE (I) JUTOGH

Amount

Demolition of brick or stone masonry, built in cement mortar incl all quoins, pillars, arches etc but excluding ashlar facing, complete all as specified and directed.

M&L for plain cement concrete, Nominal mix 1:4:8, using 40mm graded crushed stone aggregate as in foundation, filling and mass concrete complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan exc. 6 m mean radius, built in CM (1:4), complete all as specified and directed..

M&L for reuse old brick for brick work with sub class 'B' bricks, straight or curved on plan exc. 6 m mean radius, built in CM (1:6) complete all as specified and directed. Note: Bricks obtain from item no 3.00 as above)

Demolition of cement concrete (un-reinforced ) in ground floor and paving not exc. 15 cm thick (below and above ground level) complete all as specified and as directed.

M&L for 20mm thick screed bed or bedding layer in CM 1:6 for laying floor tiles, complete all as specified and directed.

M&L for chequered cement concrete tiles pre polished 30x30cmx22-25mm thick, set ,jointed and pointed in neat cement slurry with grey cement and pigment in floors, complete all as specified and directed.

M&L for 100mm thick, PCC 1:4:8, Type D-2, using 40mm graded crushed stone aggregate as in sub base of floor complete all as specified and directed.

S&F providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed.

S&F providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed

RM&L for rendering 15mm thick on fair faces of brick work or concrete surfaces, finished even and fair on walls in cement mortar (1:4), using water proofing compound, complete all as specified and directed. Note: WPC will be measured and paid for separately

M&L for rendeing 10mm thick other then fair faces surfaces in CM 1:6 finished even and smooth with out using extra cement (Internal surfaces), complete all as specified and directed.

M&L for rendering 5mm thick on ceiling surface in CM 1:3 finished even and smooth complete all as specified and directed.

M&L for preparation of new plastered surfaces/ previously untreated surface & applying two coats of oil bound distemper (OBD) over one coat of chalk white on wall surface, complete all as specified and directred.

M&L for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces, complete all as specified and directed.

M&L for three coats of white wash including preparation of new plastered on ceiling surfaces of any description complete all as specified and directed.

M&L for two coats of white wash including preparation of old plastered on ceiling surfaces of any description, complete all as specified and directed.

M&L for complete removal of existing treatment and applying two coats of oil bound distemper on wall over primer over 1-2 mm (av-1.5 mm Thick wall care putty to achieve smooth and even surface incl preparation of surface complete all as specified and directed.

M&L for complete removal of existing treatment and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. complete all as specified and directed.

Dismantling of brick or terracing tiles of single layers on roofs incl cleaning of bricks/tiles and removal of unusable bricks/tiles and removal from site, complete all as specified and directed.

Demolition of mud in roof any thickness whether full thickness removed or part thereof including plaster & leaping complete all as specified and directed.

M&L for PCC 1:2:4, type B-1, using 20mm graded mechanically crushed stone aggregates as in padding to roof to maintain the required slope and finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for screed bed 15mm thick in CM 1:4 on concrete surfaces finished even and smooth without using extra cement including mixing of water proofing compound of approved make as per manufacturers instructions on existing surfaces, complete all as specified and directed.

M&L for cleaning of roof slab surfaces including sweeping clean & washing down with water to remove dust & providing water proofing treatment with polymeric standard water proofing membrane complete all as specified and directed. (a) M&L preparation of plaster surfaces /RCC roof surfaces and applying one coat of oil bound bituminous primer @0.03 ltr/Sqm (b) M&L applying blown type bitumen @1.20Kg/Sqm of grade 85/25 (c) Supplying and laying modified polymeric water proofing membrane super thermo lay 3mm thick of weight not less than 3.00kg /sqm reinforced with polyester non woven fabric weight not less than 150gm/sqm center core including coping on the surfaces with torch application of membrane with 10cm over laps as required all complete all as specified and directed . (d) Applying two coats of aluminium paint @ 0.2 kg/sqm

Supply only Integral water proofing compound, complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, ccomplete all as specified and directed.

S&F pre-painted galvaLume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

S&F pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws as, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description in any position not otherwise provided for, complete all as specified and directed.

M&L for roof trusses framed, trussed, rail and fastenig and bracket framing (Beam, Tee, angl, tubler Sectin) of Fe-410, Gde-E-250, incl distance peaces, complete all as specified and directed.

M&L for framed work such as grills, gratings etc., with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe 290 Gde E-165, complete all as specified and directed.

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer, complete all as specified and directed.

M&L for preparation of old steel surface of any description exc. 10cm width or girth and applying one coats of synthetic enamel paint, complete all as specified and directed.

Dismantling post or struts (wood, steel or RCC) any section and size including taking out embedded portion and making good disturbed ground in natural ground, complete all as specified and directed.

All as per Srl Item No 34.00 above but for post embedded in concrete, complete all as specified and directed.

Dismantling fencing wire mesh, any type, complete all as specified and directed.

Excavation in post holes n.exc. 0.5 Cum and getting out in hard/ dense soil, complete all as specified and directed.

S&F angle iron as in posts and struts for fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc flat iron fillets (for securing wire mesh etc) including all necessary drilling bolting or riveting etc and similar work conforming to Fe-290 gde E-165 complete all as specified and directed

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire, complete all as specified and directed.

Supply only chain link MS galvanised fencing, of size 4mm (8 SWG) 75 x 75mm complete all as specified and directed.

M&L for mild steel round bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips Fe-410W (Gde E-250) quality A or Fe-290 (Gde E-165), complete all as specified and directed.

S&F Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured), complete all as specified and directed.

S&F 12 mm dia Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5 cm long & n exc 10 cm, complete all as specified and directed.

Taking down chowkaths or frames n.exc 1.5 sqm (without takingoff shutter from the frame) each and removing from the site including dismantling brick work for hold fasts etc., complete all as specified and directed.

Taking down chowkaths or frames Exc 1.5 sqm but n.exc 4 sqm (without taking off shutter from the frame) each and removing from the site including dismantling brick work for hold fasts etc., complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sqm and not exceeding 2 Sqm each, complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sqm and not exceeding 2 Sqm each and refixing in the same opening after repair etc., complete all as specified and directed.

S&F steel windows of profile rectangular tube section with side hung shutters incl projecting type hinges with steel handles, MS peg stay with glazing bars, complete all as specified and directed.

S&F steel window of profile rectangular tube section with side hung shutters incl projecting type hinges with steel handles, MS peg stay without glazing bars, complete all as specified and directed.

S&F steel windows or ventilators, fixed type, with glazing bars complete all as specified and directed.

S&F 3mm thick figured glass, pin headed type and fixed with wooden beads in squares not exceeding 0.5 Sqm in each pane, complete all as specified and directed.

S&F 3mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq.m in each pane, complete all as specified and directed.

S&F in repair 3mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq.m in each pane. incl hacking out old broken glass from metal frame inlcuding punching or drilling out old glazing pins/spring clips and providing and fixing new ones, complete all as specified and directed.

S&F pressed steel frames of size 125 x 60 mm for doors with one or more rebates including supply & fixing lugs, 125 mm size hinges, lock strike plate, etc., complete all as specified and directed.

S&F pressed steel frames of size 105 x 60 mm for doors with one or more rebates including supply & fixing lugs,125 mm size MS hinges, lock strike plate, etc., complete all as specified and directed.

S&F 30mm thick flush shutter, solid core construction with block board core and plywod face panels, both faces are covered with decorative face veneer with lipping/ frame to match complete all as specified and directed.

S&F 35 mm thick factory made glazed & Skelton shutter of IInd class hardwood open rebated & prepared to receive glass or gauze etc without sash bar open rebated with edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass or guage etc size of stiles rails etc as specified in sec 8 clause 8.24 (a) of SSR Part-I (2010), complete all as specified and directed.

S&F solid PVC door frames of size 50mm x 47 mm made out of 5mm wood grain printed PVC sheet reinforced with MS square tube, supply & fixing in opening as per specification & drawing complete all as specified and directed.

S&F factory made solid PVC moulded door shutter, with particle board core 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification complete all as specified and directed.

S&F butt hinges, 100mm long extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-22 complete all as specified and directed.

S&F Aluminium tower bolt of extruded section, 200mm length of bolt and fixed with screws, complete all as specified and directed.

S&F 125mm size, aluminium (cast type) anodized, handle and fixed with screws complete all as specified and directed.

S&F 300mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy and fixed with screws, complete all as specified and directed.

S&F floor door stopper aluminium body and tongue,anodised overall length of cover plate of size 140 mm long with hard drawn steel spring complete all as specified and directed.

M&L for PCC 1:3:6, type C-1, using 20mm graded mechanically crushed stone aggregate as in filling pressed steel frame /hold fast blocks etc., complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

M&L for preparation of new wooden surface of any description not otherwise described over 10cm width or girth and applying two coat of syntheatic enammel paint over one coat of pink primer complete all as specified and directed.

S&F in repair 300 mm MS ordinary rat tail rod pattern springs incl roller and roller plate fixed to wooden chowkhats or welded to angle iron door frames complete all as specified and directed.

Taking up or down steel tubing and connections of 15mm bore in pipe, including cleaning for re-fixing or removal from site, complete all as specified and directed.

Taking up or down steel tubing and connections of 20mm bore in pipe, including cleaning for re-fixing or removal from site, complete all as specified and directed.

S&F GI tubing medium grade 15mm dia incl fittings, cutting threading and fixing to walls or fixing in concealed walls or in floors etc, and making good the surfaces matching to exsiting surafaces of walls/ floor, complete all as specified and directed.

Re-fixing old steel tubing 15 mm dia and connections in new or old positions, complete all as specified and directed.

Re-fixing old steel tubing 15 mm dia and connections in new or old positions, complete all as specified and directed.

Re-fixing old steel tubing 20 mm dia and connections in new or old positions, complete all as specified and directed.

S&F in repair 110mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, complete all as specified and directed.

S&F in repair 75mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, complete all as specified and directed.

S&F in repair PVC (SWR) floor trap 75mm, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F in repair PVC (SWR) junction single, (Single T 110mm), equal or unequal with access door complete all as specified and directed.

S&F in repair PVC (SWR) junction single, (Single T 75mm), equal or unequal with access door complete all as specified and directed.

S&F in repair PVC (SWR) bends, for 110mm bore pipes, with access doors, complete all as specified and directed.

S&F in repair PVC(SWR) bends, for 75mm bore pipes, with access doors, complete all as specified and directed.

Dismantling water tanks of capacity exc 250 & n.exc 500 ltrs and removing from site to store, complete all as specified and directed.

S&F rotational moulded polythelene water storage tanks of 500 ltr capacity (cylindrical vertical with closed top) three layer hoisted and fixed in position, SSR Part-I, complete all as specified and directed.

S&F in repair ball valve of brass, 20mm bore, high pressure with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified and directed.

S&F in repair CI gate valve, 20mm bore, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or unions complete all as specified and directed.

S&F in repair CI gate valve, 15mm bore, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union, complete all as specified and directed.

S&F in repair fancy type, chromium plated Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and directed.

S&F in repair 10 ltr capacity PVC valve less, syphonic action type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, 32 mm dia flush pipe, complete all as specified and directed.

S&F in repair vitreous china wash hand basin white flat back of size 550x440mm including CI brackets, chromium plated waste coupling, waste pipe of size 32mm dia etc., (incl all waste fittings), complete all as specified and directed.

S&F in repair fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lattered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe of size 15mm dia iron pipe complete all as specified and directed.

S&F in repair 15 mm fancy type chromium plated fancy type bib tap brass long body with flange screwed down high pressure CP cast copper alloy with crutch or butterfly handles scrwed down suitable for 15mm bore pipe or union, complete all as specified and directed.

S&F in repair, Vitreous china wash down water closet pan (Pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe), but including plastic water seat cover white/coloured closed pattern with flat bottom and cover with PVC hing devise, fixing bolt for padestal pattern and cast iron 'P' or S trap complete all as specified and directed.

S&F in repair for PVC water closet seat cover, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, complete all as specified and directed.

S&F health faucet (ABS Body) with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position, complete all as specified and directed. Make: Hindware or equivalent from Parryware/ Cera as approved by AO

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), rubbish off the premises, complete all as specified and directed.

M&L for machine cut Kota stone slab 18-20 mm thick, laid over and including 20mm thick screed bed in cement mortar (1:6) using coarse sand as in flooring, set & jointed in neat grey cement slurry and ponted in white cement mixed with pigment to match including grinding and polishing to granite finish complete all as specified and directed.

M&L for glazed ceramic coloured tiles in vertical surfaces 350x250mmx7mm/450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match on vertical surface such as skirting , dado etc. over 10 mm thick backing coat plaster in CM 1:4, complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (squares/ rectangular) area of each tile exceeding 0.11 sqm but not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thickscreed bed with CM 1:6, complete all as specified and directed.

M&L for Non Skid ceramic coloured tiles 7 to 8mm thick (squares/ rectangular) area of each tile exceeding 0.18 sqm but not exc 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thickscreed bed with CM 1:6, complete all as specified and directed.

KK BUILDERS (BID ID -3500865)