REPAIR/ REPLACEMENT TO CAR SHED SHUTTER, ROOF SHEET, SEEPAGE, CHAJJAS, WATER TANK, PIPELINES, ROOF TREATMENT AND OTHER MISC WORK AT OFFICERS MD ACCN AND ZONE B AREA UNDER AGE B/R II OF GE SUKNA IN SUKNA MIL STN

Amount

M & L for sand filling under floors or in foundations including watering and consolidation as required complete all as specified and directed.

Supply only integral water proofing compound complete all as specified.

M & L for providing 25 mm thick pre-cast cement concrete louvers or RCC Jali made out of cement concrete 1:2:4 type B-0, using 12.5 mm graded stone aggregate and set in cement mortar 1:4 including all mouldings etc. complete all as specified and directed.

M&L RCC 1:2:4 Type B1 (20 mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and like complete all as specified and as directed.

M & L for plain cement concrete (1:2:4) Nominal Mix (using 20 mm graded stone aggregate), as in roof kerbs or mud stops, rounded or chamfered on edges including necessary form work as required complete all as specified and directed.

Cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, lintels, shelves etc, and cutting chases for concealed water tubing or concealed conduit wiring etc, and making good on brick walls, cutting not exc. 10 cm in girth complete all as specified and directed

M & L for brick work with sub class ‘B’ old size bricks straight or curved on plan exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M & L for brick work with sub class ‘B’ old size bricks, straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

M & L for Granite work (of any type) 18-20 mm thick (table rubbed and polished) as in counter basin fixed in CM 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with granite shade over 15 mm thick screed bed in CM 1:4 including demolition complete all as specified and directed.

M & L for use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar works not exc. 200 mm thick horizontal or slopping in rough finished flat surface of concrete complete all as specified and directed.

Taking down chowkhats or frames area exc. 1.50 Sqm but not exc. 4.00 Sqm each complete all as specified and directed.

Taking down door shutter of any description exc. 1 but n exc 2 sqm each complete all as specified and directed.

Taking down chowkhats or frames area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down door shutter of any description exc. 1 sqm but not exc. 2 sqm each & Refixing at same opening complete all as specified and directed.

M & L for 2nd class hard wood (SAL) plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S&F 30 mm thick pre-laminated medium density fibre (MDF) board flush door shutter, both side laminated of approved colour, interior grade complete all as specified and directed.

S&F factory made 28 mm thick solid PVC flush door shutter, made from co-extruded three layer rigid PVC foam sheet (single extruded), water proof, termite proof & fire retardant having density 600 kg/cum (minimum), outer layer 0.8-1mm thick of rigid PVC with density 1400 Kg/Cum complete all as specified and as directed.

S & F factory made solid wood polymer composite (WPC) door frame of size 90 x 45 mm, (Moulded) single rebated, decorative type, single extruded process WPC with density 780 Kg/Cum (minimum), Compressive strength 58 N/mm2 (Minimum), K Value 57-60 ( Suspension Grade), water/moisture proof, termite / borer proof & fire retardant complete all as specified and directed.

S & F of 30 mm thick (Batten thickness) 2nd class hardwood (SHISHAM) plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged) and size of the members of shutter is as specified in clause No. 8.24 (a) of MES schedule part – I (Specifications -2009) complete all as specified and directed.

S & F of 35 mm thick (Batten thickness) 2nd class hardwood (SHISHAM) glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. without sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. and size of the members of shutter is as specified in clause No. 8.24 (a) of MES schedule part – I (Specifications - 2009) complete all as specified and directed.

S & F factory made Solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain coloured PVC sheet reinforced with mild steel square tube as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S & F 30 mm thick (style thickness) factory made solid panel PVC shutter consisting of frame made out of mild steel tubes for top and bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rails with suitable PVC sheets beading and joined together with solvent cement as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S & F in repair galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks of galvanised wire staples complete all as specified and directed.

S & F galvanised mild steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks of galvanised wire staples complete all as specified and directed.

S & F of 100 mm long mild steel butt hinges, medium weight cold rolled complete all as specified and directed.

S&F 150 mm long aluminium, anodised, barrel tower bolt of extruded section and fixed complete all as specified and directed.

S&F 150 mm Aluminium handles cast type, anodised and fixed complete all as specified and directed.

S & F of 300 mm long (Length of bolt) aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolt of extruded sections or cast aluminium alloy complete all as specified and directed.

S & F of 150 mm size (Overall length of cover plate) floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and directed.

S & F of 40 mm wide flap when open, mild steel bright finish or electro galvanised continuous (Piano) hinge complete all as specified and directed.

S & F of 50 mm size Polished Hard wood knobs fixed with screws complete all as specified and directed.

S&F in repair mortice lock, vertical type, size 100 mm four lever of Aluminium complete all as specified and directed.

S & F in repair of Door closer Aluminium(Die cast) body Hydraulically regulated ( designation No. 3) universal type, suitable for door shutters of 851 to 1000 mm in width and weight between 61 t0 80 kg complete all as specified and directed.

S & F in repair of 300 mm mild steel ordinary rat tail, rod pattern springs including roller and roller plate complete all as specified and directed.

S&F magnetic catch of size not less than 75 x 15 mm suitable for cup board complete all as specified and directed.

S&F non asbestos fibre cement building boards 4 mm thick (designer pattern) fixed or laid / inserted to GI framework with screws in seamless false ceiling (flat or sloping) of grid size 605 x 605 mm and including GI frame work comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with contacting clips across the intermediate channel at 457 mm centre to centre hanging from structural steel / scantling with 6 mm GI wire and GI flat 40x3 mm 60 mm long and including dismantling complete all as specified and directed.

M&L decorative type plaster of paris work of size not less than 50 mm x 50 mm, as in cornice or junction of wall and ceiling complete all as specified and directed.

S & F of mild steel work as in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS – 1161 – 1979 grade St – 240 complete all as specified and directed.

S&F anodised aluminium powder coated (thickness or powder coating not less than 50 micron) in frame and shutters of door, window and ventilator , sliding type or openable type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodised aluminium fittings etc. complete all as specified and directed. Note : (a) Weight of rubber gasket beading, roller wheels etc will not be measured with the weight of aluminium shutters as only aluminium items shall be measured. (b) Wire mesh shall be measured and paid separately. (c) Aluminium hinges shall be included in the unit rate.

S & F of Pressed steel frame of size 125 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc.and including P.C.C. (1:3:6) for filling in frame and fixing of hold fast, complete all as specified and directed.

S & F of steel window with side hung shutters including projecting type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S & F of steel window with side hung shutters including projecting type hinges with steel handle and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.

S & F of mild steel framed work such as grills, gratings etc. with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing, frame work of water tanks and similar work conforming to Fe – 290 Gde E -- 165 complete all as specified and directed.

S & F of steel ventilator with top hung shutter including hinges, steel peg stay complete all as specified and directed.

S & F of flat iron bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gate, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fast, wall ties, hooks for hanging fans and other similar small steel article conforming to Fe – 290 Gde E -- 165 complete all as specified and directed.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S & F in repair of push pull or manual type steel rolling shutter, without ball bearing but including top cover, anchoring rod, haps and staple and one shop coat of primer, erected in position as indicated, thickness of laths 1.00 mm complete all as specified and directed.

S & F of ball bearing for rolling shutter complete all as specified and directed.

S & F Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

M&L PCC 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) as in gap between roof sheet and brick wall, thickness of concrete bed exc. 5 cm and not exc. 10 cm thick & width not exc. width of one brick thick wall including necessary scaffolding and formwork complete all as specified and directed.

S&F in repairs 18 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white laminated fixed with screw to timber / aluminium frame work complete all as specified and directed.

M&L for roof treatment in order of precedence as given below complete all as specified and as directed:- (i) Taking out of existing water proofing treatment and including padding, cleaning the surface using wire brush, brooming down and washing down with water to remove dust etc, and brushing with neat cement slurry @ 3.00 kg of cement per Sqm. (ii) 15 mm thick screed bed in CM 1:4 on surface. (iii) Cleaning of plastered surface and applying one coat of bituminous primer @ 0.40 Ltr / Sqm.

(iv) Supply and laying 3 mm (Minimum) thick APP based polymeric membrane of approved manufacturer with weight not less than 3.60 Kg per Sqm, reinforced with non-woven polyester fabric weight not less than 150 gms per Sqm. Polymeric membrane shall be taken to a height of 30 cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing. (v) Applying one coat of water proofing paint with aluminium finish over APP as per manufacturer's instruction. Note :- (a) Bituminous primer shall be "ShaliTex Primer" manufactured by M/s STP Ltd or equivalent in M/s Sika India Pvt Ltd or M/s Fosroc Chemicals or M/s Hindcon chemicals limited or M/s IWL India Limited (b) Laying APP based polymeric membrane shall be done by torch on method as per manufactures instructions. (c) A minimum overlap of 100 mm and 75 mm should be made at the end and sides of the polymeric membrane respectively and all overlaps and joints shall be sealed as per manufacturers instruction. (d) APP based polymeric membrane shall be manufactured by M/s STP Ltd or Berger Paints or M/s Sika India Pvt Ltd or M/s Fosroc Chemicals or M/s Hindcon chemicals limited or M/s IWL India Limited (e) Water proofing paint shall be by M/s STP Ltd or Berger Paints or M/s Sika India Pvt Ltd or M/s Fosroc Chemicals or M/s Hindcon chemicals limited or M/s IWL India Limited

M & L for providing 75 mm thick cement concrete (1:3:6), Type C-2, Nominal Mix (using 40 mm grade stone aggregate) as in plinth protection complete all as specified and directed.

M & L for providing 75 mm thick cement concrete (1:4:8) Nominal Mix type D-2 (using 40 mm grade stone aggregate) as in sub floor, sub base of floor complete all as specified and directed.

M&L 8-10 mm thick vitrified ceramic tiles light shade (square / rectangular) polished, area of each tiles n. exc. 0.36 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L 8-10 mm thick vitrified ceramic tiles light shade (square / rectangular) polished, area of each tiles n. exc. 0.36 sqm in vertical surfaces in skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10 mm thick backing in CM 1:3 complete all as specified and directed.

M&L 8-10 mm thick vitrified heavy duty digital paving tiles (square / rectangular) polished, area of each tiles n. exc. 0.11 but n. exc 0.18 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 20 mm thick in CM 1:6 complete all as specified and directed.

M & L for Glazed ceramic coloured tiles of size 350 mm X 250 mm X 7 mm thick or 450mm X 300mm X 7 mm thick as on vertical surfaces such as skirting, dados and rises to steps etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile including cement screed bed of 10 mm thick 1:3 in cm complete all as specified and directed.

M&L in repair pre-polished cement concrete chequered tiles 300 x 300 x 25 mm thick as in floors, set and jointed over and including 15 mm thick screed bed in CM 1:4 and pointed in grey cement and pigments to match the colour of tile complete all as specified and directed.

M&L 60 mm thick machine pressed precast concrete interlocking coloured paver block of any shape and size confirming to IS 15658-2006, M-35 grade, set with grey cement and pigment complete all as specified and directed.

Taking down cement or cement lime plaster from brick or stone walls etc. including raking out joints, hacking for keys, scrubbing down with water etc. complete all as specified and directed.

M & L for 15 mm thick rendering in cement mortar 1:4 on other than fair faces of brick work or stone masonry or on one side of lathing surfaces and finishing the surface even and smooth without using extra cement complete all as specified and directed. Note:- WPC shall be measured and paid separately.

M&L 5 mm thick rendering in CM 1:3 on fair faces of brick work or concrete surfaces as in ceiling, chajja, soffits etc, and finished even and smooth without using extra cement complete all as specified and directed.

M & L for 15 mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces and finishing the surface even and smooth without using extra cement complete all as specified and directed.

M&L preparing of old plastered or un plastered surface of walls and applying one coats of white wash complete all as specified and directed.

M&L preparing of old plastered or un plastered surface of celing and applying one coats of white wash complete all as specified and directed.

M&L preparing of old plastered or un plastered surface of walls and applying one coats of oil emulsion distemper complete all as specified and directed. Make of oil bound distemper :- Apcolite Premium Emulsion (Asian Paints ltd)/ Rangoli (Berger) / No. 1 Premium Acrylic Distemper(Shalimar) Make of primer/ wall care putty:- Asian Paints/ Berger / Shalimar Paints

M&L complete removal of existing treatment of old decorated wall surfaces and including applying two coats of oil bound distemper over a coat of primer and over a thin layer of wall care putty to obtain smooth finish complete all as specified and directed. Make of oil bound distemper :- Apcolite Premium Emulsion (Asian Paints ltd)/ Rangoli (Berger) / No. 1 Premium Acrylic Distemper(Shalimar) Make of primer/ wall care putty:- Asian Paints/ Berger / Shalimar Paints

M&L preparation of new plastered wall surfaces and including applying two coats of oil bound distemper over a coat of primer and over a thin layer of wall care putty to obtain smooth finish complete all as specified and directed. Make of oil bound distemper :- Apcolite Premium Emulsion (Asian Paints ltd)/ Rangoli (Berger) / No. 1 Premium Acrylic Distemper(Shalimar) Make of primer/ wall care putty:- Asian Paints/ Berger / Shalimar Paints

M&L preparation of new plastered surfaces of ceiling and including applying two coats of oil bound distemper over a coat of primer and over a thin layer of wall care putty to obtain smooth finish complete all as specified and directed. Make of oil bound distemper :- Apcolite Premium Emulsion (Asian Paints ltd)/ Rangoli (Berger) / No. 1 Premium Acrylic Distemper(Shalimar) Make of primer/ wall care putty:- Asian Paints/ Berger / Shalimar Paints

M&L preparation of old decorated wall surfaces and including applying two coat of weather coat acrylic exterior emulsion paint over a coat of primer complete all as specified and directed. Make of acrylic exterior emulsion paint : Apex Dust Prooff Emulsion (Asian Paints Ltd)/ Weathercoat Glow(Berger)/ Xtra Tough(Shalimar) Make of primer/ wall care putty:- Asian Paints/ Berger / Shalimar Paints

M&L preparation of new plastered wall surfaces and including applying two coats of exterior weather coat paint over a coat of primer and over a thin layer wall care putty complete all as specified and directed. Make of acrylic exterior emulsion paint : Apex Dust Prooff Emulsion (Asian Paints Ltd)/ Weathercoat Glow(Berger)/ Xtra Tough(Shalimar) Make of primer/ wall care putty:- Asian Paints/ Berger / Shalimar Paints

Hacking out old broken glass (any thickness, size, quality or description) from metal frames glazed with oil putty or fixed with beads including punching or drilling out old glazing pins / spring clips and providing and fixing new ones complete all as specified and directed.

S & F of 3 mm thick plain sheet glass, ordinary quality and glazing with oil putty or fixed with beads in square not exc. 0.5 Sqm in each pane complete all as specified and directed.

S & F of 4.8 mm thick plain sheet glass, ordinary quality and glazing with oil putty or fixed with beads in square exc. 0.5 Sqm in each pane complete all as specified and directed.

M&L preparation of old painted wooden surfaces of any description, over 10 cm in width or girth, not otherwise described and including applying one coat of synthetic enamel paint complete all as specified and directed. Make of synthetic enamel paint:- Apcolite Premium Gloss Enamel (Asian) / Luxol High Gloss Enamel (Berger) / Superlac Premium High Glass Enamel (Shalimar Paints Ltd)

M&L preparation of old painted steel surfaces of any description, over 10 cm in width or girth, not otherwise described and including applying one coat of synthetic enamel paint complete all as specified and directed. Make of synthetic enamel paint:- Apcolite Premium Gloss Enamel (Asian) / Luxol High Gloss Enamel (Berger) / Superlac Premium High Glass Enamel (Shalimar Paints Ltd)

M & L for preparation of New or previously untreated wooden surfaces exc. 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. Make of synthetic enamel paint:- Apcolite Premium Gloss Enamel (Asian) / Luxol High Gloss Enamel (Berger) / Superlac Premium High Glass Enamel (Shalimar Paints Ltd) Make of primer/ wall care putty:- Asian Paints/ Berger / Shalimar Paints

M & L for preparation of New or previously untreated steel surfaces exc. 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. Make of synthetic enamel paint:- Apcolite Premium Gloss Enamel (Asian) / Luxol High Gloss Enamel (Berger) / Superlac Premium High Glass Enamel (Shalimar Paints Ltd) Make of primer/ wall care putty:- Asian Paints/ Berger / Shalimar Paints

S & F 15 mm bore galvanised steel water tubing medium grade with and including all fittings and fixed to walls and ceilings or laid under floors including taking down complete all as specified and directed.

S & F 20 mm bore galvanised steel water tubing medium grade with and including all fittings and fixed to walls and ceilings or laid under floors including taking down complete all as specified and directed.

S&F in repairs 15 mm bore bib tap chromium plated, cast copper alloy with crutch or butterfly handle, screwed for iron pipe or for brass ferrule & fixed complete all as specified and directed.

S&F in repairs 15 mm bore bib tap chromium plated, Fancy Type,long body,cast copper alloy with crutch or butterfly handle, screwed for iron pipe or for brass ferrule & fixed complete all as specified and directed.

S&F in repairs vitreous china european water closet pan (pedestal pattern) white in colour with fixing bolts and flush pipe, connection to trap and to flushing cistern and all joints, closed pattern with flat bottom and cover and mild steel CP hinges complete all as specified and directed.

S&F vitreous china wash hand basin white flat back of size not less than 550 x 400 mm with and including PVC waste pipe 32 mm bore, CP waste fitting and cutting for and pinning in ends of brackets etc, complete all as specified and directed.

S&F in repair PVC low level flushing cistern of 10 litres capacity, valve less, syphonic action type, white body, with inlet ball valve, float and handle including brackets complete all as specified and directed.

S&F in repairs pillar tap 15 mm bore,Fancytype, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without lettered “hot" or “cold” with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S&F in repairs plastic water closet seat cover white, closed pattern with flat bottom and cover and mild steel CP hinges for european water closet pan complete all as specified and directed.

S&F in repairs PVC cabinet of size not less than 300 x 343 x 250 mm for bathroom, with single door shutter complete all as specified and directed.

S&F in repairs sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf, size not less than 120 mm wide & 600 mm long, with chromium plated bracket guard and railing complete all as specified and directed.

S&F in repairs grating doom 100 mm dia of stainless steel fixed to floor trap complete all as specified and directed.

S&F in repairs stop cock/ angle stop cock 15 mm bore, cast copper alloy, screwed down high pressure, with crutch of butterfly handle, screwed both ends for iron pipe or unions and fixed, fancy type, chromium plated long thread with flange complete all as specified and directed.

S&F in repairs health faucet 15 mm bore, ABS chromium plated with & including 1.0 mtr chromium plated flexible tube & wall hook complete all as specified and directed.

S&F in repairs central hole basin mixer, brass, chromium plated, for mixing hot and cold water, with 450 mm Long Braided Hoses, screwed down for 15 mm bore pipe complete all as specified and directed.

S&F in repairs brass chromium plated wall mixer, 3-in-1 system having provision for both, hand shower and overhead shower, with bend pipe, connecting legs and wall flages (without hand & overhead shower) complete all as specified and directed.

S&F decorative corner glass shelf assembly consisting of 5.5 mm thick sheet glass shelf, and side not less than 225 mm with chromium plate bracket guard complete all as specified and directed.

S&F decorative polished CP brackets / supports to be fixed at walls for holding curtain rods and corners to be fixed at ends of curtain rod of 20mm dia with necessary screws complete all as specified and directed. Note :- 2 Nos bracket and 2 Nos corners shall be measure as one pair

S&F 28 mm dia curtain rod, mild steel, chromium plated with & including six nos. curtain ring per running meter including suitable fixing CP round knobs to be fixed at ends etc. with necessary screws complete all as specified and directed.

S&F PVC connections 15 mm size with PTMT nuts, of length 450 mm complete all as specified and directed.

S&F in repairs 32/40 mm bore PVC waste pipe for WHB / Sink etc. complete all as specified and directed.

S&F in repairs 100 mm size swivel shower rose of ABS, chromium plated with long head arm for fixing with 15 mm pipe complete all as specified and directed.

S&F in repairs door seal made out of tripple seal neoprene rubber fitted with aluminium strip, length not exc 1.20 m complete all as specfied and as directed.

Cleaning and removing all scale and dirt etc. from tanks and from mouths of circulating pipes of capacity 500 litre to 1000 litre PVC water storage tank without dismantling the tank and including writing the words "Tank Cleaning done on ____" indicating the date, month & year of cleaning on external surface of tank wall with synthetic enamel paint complete all as specified and directed.

S&F in repairs rotational moulded polyethylene water storage tanks of 1000 Litres capacity, multilayered (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia nipple suitable for HDPE water tank (minimum weight 45 gm), 20 mm bore ball valves (minimum weight 210 gm) high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed to 20 mm bore pipe & locking with GI wire (to prevent monkey menace) to tank complete all as specified and directed.

S&F in repairs 20 mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (minimum weight 210 grams) complete all as specified and directed.

S&F 15 mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F 20 mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repairs sink with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915 x 460mm bowl size 405 x 355 x 178 mm complete all as specified and directed.

S&F in repair 15mm dia 2 way stop cock/Bib cock fancy type chromium plated complete all as specified and directed .

S&F in repair 15mm dia stop cock fancy type chromium plated concealed type complete all as specified and directed.

S&F in repairs brass chromium plated toilet paper holder complete all as specified and as directed.

S&F towel rail, 18 mm (minimum) dia & 600 mm long of stainless steel chromium plated, fixed with and including chromium plated brass screws and wooden / plastic cleat complete all as specified and directed.

S&F in repairs PVC (SWR) pipes 75 mm bore single socketed in any length with rubber ring joints fixed to wall complete all as specified and as directed.

S&F in repairs PVC (SWR) pipes 110 mm bore single socketed in any length with rubber ring joints fixed to wall complete all as specified and as directed.

S&F PVC (SWR) 75 mm bore bend with access door, of any radius complete all as specified and directed.

S&F PVC (SWR) 110 mm bore bend with access door, of any radius complete all as specified and directed.

S&F 75 mm bore PVC (SWR) floor trap, plain with grating and including jointing with solvent cement complete all as specified and directed.

S&F in repair CP fancy type soap dish holder of dia not less than 110mm, with wall flange complete all as specified and as directed.

Dismantling of structural steel work including doors, gates but excluding framed trusses complete all as specified and directed.

Dismantling of corrugated or semi corrugated Asbestos Cement (AC) sheets in roof covering complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving Not exc. 15 cm thick but above ground floor complete all as specified and directed.

Demolition of brick work or stone / boulder masonry including all quoins, arches, pillars, etc. built in cement mortar or cement lime mortar complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of Re-inforced Cement Concrete in any position and any description including cutting of reinforcement bars to facilitate demolition complete all as specified and directed.

M&L making good broken / damaged RCC chajjas with PCC 1:2:4 type B1 or cement mortar 1:3 and including rendering 15 mm thick in CM 1:4 mixed with water proofing compound as per manufacturer's instruction to top, sides and soffits, including necessary scaffolding, formwork upto 3 storey height complete all as specified and directed. Note:- Water proofing compound shall be measured and paid seperately

M/s TALCO

DEBABROTA ROY CHOWDHURY

PS ENTERPRISE

M/S G S ASSOCIATES

KARMIBRINDA

R N SAH N CO

MS ESSCON

M/S GLORIOUS CONSTRUCTION