Spl repair to bldg No-04 (Ch), T-139 (Ch), T-62 (OR Living) at DBN and provn of over head water tank capacity 30000 Ltr at Shikar under GE Gurdaspur.

Amount

M&L for taking down wooden roof trusses, coupled rafters or trussed beams , for span 4 to 8mtr.

Dismantling timber scantlings 40 sq. cm and over in section, in any position

Dismantling wall and ceiling boards (fibre, pulp, insulation ,etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground leve) complete all as specified & directed by Engineer-in-Charge.

Demolition of brick work or stone/boulder masonry built in cement mortar incl all quoins, arches, pillars & precast concrete masonry etc complete all as specified & directed by Engr-in-Charge.

Taking down cement plaster on brick or stone walls, ceiling etc, including raking out joints, hacking for key, scrubbing down with water, etc.

M&L brick work with fly ash bricks , straight or curved on plan exc 6m mean radius built in CM1:6 complete all as specified & directed by Engr-in-Charge.

M&L brick work with old size subclass ‘B’ bricks except bricks recd from demolition, straight or curved on plan exc 6m mean radius built in CM1:6 complete all as specified & directed by Engr-in-Charge.

M&L brick with sub class 'B' brick, straight or curved on plan to any radius in half brick thick walls built in CM 1:4

M&L for 75 mm thick, PCC 1:3:6 type C1 (using 20mm graded stone aggregate), finished even and smooth without using extra cement.as in plinth protection to raise level incl mastik filling complete all as specified.

M&L rendering 12 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 incl finished even and fair (without using extra cement) complete all as specified and directed.

M&L rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 incl finished even and fair without using extra cement complete all as specified and directed.

M&L preparation of new plastered surface and applying two coats of cement base paint over a coat of primer on wall complete all as specified and directed.

M&L for preparation of old plastered surface by complete removal existing treatment and applying two coat of cement base paint complete all as specified and directed.

M&L preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

M&L for preparation of old plastered surface by complete removal existing treatment and applying two coat of OBD complete all as specified and directed.

M & L for preparation of new plastered wall surfaces and applying three coat of white wash complete all as specified.

M & L for preparation of old decorated wall surfaces and applying one coat of white wash complete all as specified.

M&L for 6mm thick plain AC building boards fixed to timber frame work/ fillet with screws in ceiling flat or sloping complete all as specified and directed.

M&L for 2nd class hard wood plain fillet square, rectangular or triangular exc 6 sqcm but n. exc 13 sqcm in section, clean sawn, secured with screws complete all as specified and directed.

All as per Srl item No 20 above but except battens.

M&L preparation of untreated ceiling surface of plain AC sheets and applying three coat of white wash on ceiling complete all as specified and directed.

Taking down chowkats with shutter exc 1.50sqm but n.exc 4 Sqm each (without taking off shutter for the chowkats and removing to store complete all as specified and directed.

S&F pressed steel frame for doors with one or more rebate including necessary fixing lugs, hinges, lock strike, plate etc complete of size 125x60mm including one shop coat of priming and two coats of synthetic enamel paint complete all as specified and directed.

S&F pressed steel frame for doors with one or more rebate including necessary fixing lugs, hinges, lock strike, plate etc complete of size 105x60mm including one shop coat of priming and two coats of synthetic enamel paint complete all as specified and directed.

M&L for providing PCC 1:2:4 tybe B-0 using 12.5 mm aggregate in ffilling of MS frame complete all as specified and directed.

S&F M&L 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F factory made glazed and skeleton shutters 35mm thick of 2nd class hard wood open rebated and prepared to receive gauge & glass etc with edge of sash bar and number edges of framing plain chamfered beads for securing glass etc size of number of shutters as spd SSR Part-I & section 8 clause 8.23 & (b) complete all as specified and directed.

S&F steel window 1.25mm thick box type ERW hollow P section of size 60mmx25mm double rebated comprises of glazed & gauged skelton shutter of (required no of gauged shutters and glazed shutters) ERW section 50mmx20mm & 1mm thick with one openable leaf consisting of two number sash bars of T-Section 20mmx3mm complete welded to frame with one vertical mullion of ERW box type T-Section of size 60mmx25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 (four Nos for each window) including one shop coat of priming and two coats of synthetic enamel paint and taking down old existing window complete with following fittings welded to the frame shutter :- Ref Drg No CE JZ/TD-06/07 (i) Hold fast,150mm long of 12mmX3mm made to shape-04 Nos per window (ii) Handle of Z section 20mmX25mm,100mm long-01Nos per window (iii) MS Tower bolt 150mm long-02 Nos per window (iv) Z sec 20mmX25mm,100mm long stopper -01 Nos per window (v) Cleat 55mm long of hollow square 15mmX12mm-02Nos per leaf (vi) Fabrication & fixing arrangements as Drg No CEJZ/TD-1020/06 (vii) M S guard bar 12mm square bars @150mm C/C fixed horizontly.

S&F steel window/ ventilator box type made of ERW tube hollow P section of size 60mmX25mm outer frame (single rebated) comprising glazed skelton shutter frame of ERW tube P section including MS guard bars, fittings and fixtures welded to frame/ shutters all as shown on drg No. CEJZ/TD-1019/08 Sh 1/3 to 3/3 including Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts, including one shop coat of priming and two coats of synthetic enamel paint including taking down old existing window/ ventilator complete all as specified and directed. Notes: (i) Thickness of the sheet shall be of 18 gauge. (ii) Glass/ wire mesh, shall be measured and paid for separately

S&F Aluminium anodized barel tower bolt of extruded section 150mm long complete all as specified and directed.

S&F aluminium alloy handle fabricated type anodized of size 150 mm long complete all as specified and directed.

S&F Aluminium alloy, anodised, 250 mm sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

S&F in repair 300mm, mild steel ordinary rat tail rod pattern springs, including roller and roller plate, fixing through welding/ bolt in metal/wooden frame or necessary alternative arrangements to be done complete all as specified and directed.

S&F for galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putting in squares n.exc. 0.50 Sqm each complete all as specified and directed.

M&L preparation of new or previously untreated wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified & directed.

M&L preparation of new or previously untreated steel surfaces of any description over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primier complete all as specified & directed .

M&L prepartion of old steel surfces of any decsription not other wise described over 10cm width or girth and applying one coat of syn enamel paint complete all as specified.

Dismantling of asbestos cement corrugated or semi corrugated sheets in roof covering of any gauge and thickness complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified & directed.

S&F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified & directed.

Steel work in tubular trusses incld special shaped washers etc, complete using ERW or induction Butt welded tubes conforming to IS 1161-1979 grade St-240

MS plates Square, cut or notched forming holes, without any attachment conforming to Fe 410-W Gde E-250 Quality A

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or suare nut, length of bolt exc 30 cm long,diameter of neck in mm 16 to 20 mm complete all as specified and directed.

Cutting holes into or through brick walls built in mud mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required exc 150 Sqcm but n,exc 400 Sqcm complete all as specified and directed .

M&L for PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed .

M&L for PCC 1:3:6 type C1 (using 20mm graded stone aggregate) lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, neelers, apex stones, bed plates, kerbs not provided for in item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating,complete all as specified & directed by Engr-in-Charge.

Supply and fixing curtain rod 20mm dia of anodised aluminium alloys with fixing brackets, stops, rollers etc fixed to wall with screws, PVC plug including taking down existing curtain rod and decorative complete all as specified and directed.

S&F 3.15mm dia of Plain mild steel wire , galvanised class 3, including straining and fixing to brick, concrete in detached work such as for mosquito nets and fixing to straining bolts, hooks, eyes, etc.all as specified and directed.

M&L non skid coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the colour of tiles including 20 mm thick screed bed in CM 1:6 complete all as specified.

All as per Srl item No 51 above but on vertical surface as in skirting including 10 mm thick screed bed in CM 1:3 complete all as specified.

M&L including taking down for ceramic glazed coloured tiles of size 350x250x7mm/ 450x350x7mm/ 300x200x7mm thick joint free on and incl 10mm thick screed bede in cm(1:4)set and jointed in neat cement slurry and pointed in colored cement mixed with pigment to match the colour of tiles on vertical surfaces of wall as in skirting/dado complete.

Demolition for tone slabs and tiles of any description or thickness in floors, aprons incl Laid, bedded and pointed in any mortar etc.

S&F machine cut Kota stone slab flooring 20-25mm thick over cement screed bedding 15 mm thick in CM 1:4 jointed with grey cement slurry mixed with pigment to match the shade of slab incl rubbing and polishing (with bees wax polish) complete all as specified and directed.

M & L for Green Marble work 14mm to 16mm thk (table rubbed and polished) in steps, jambs, pillars window cills , cooking platforms , stair case and like in cement mortar ( 1:4) incl pointing in white cement ( 1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed.

S & F rotational moulded polytheylene triple layered white water storage tanks of capacity 1000 Litres(cylindrical vertical with closed top) hoisted and fixed in position including dismantling of existing water tank and 20mm dia brass float valve with brass rod complete all as specified.

S&F in repair 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed etc complete all as specified and directed.

Taking up and down GI pipe15mm bore including fittings, connection, including cleaning for reuse or removal to store complete all as specified and directed.

All as per Srl item No 59 above but 20mm bore of pipe.

S&F GI tubing 15mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings ISI marked complete all as specified.

S&F GI tubing 20mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings ISI marked complete all as specified and directed.

S&F in repair bib taps 15mm dia chromium plated fancy type with capstan head screwed down screwed for iron pipe or for brass ferrule and fixed in repairs complete all as specified and directed.

S&F Stainless steel sink, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc., overall size 495mm x 420mm with bowl complete all as specified and directed.

M&L for RCC in 1:2:4 type B-0(using 12.5 mm graded stone agg) as in chajjas facia, shelves etc and similar work complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam aunchings,Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.

S&F low density polyethylene pipes (LDPE) 40mm bore of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc.

M&L 75 mm thick cement concrete 1:4:8 type D-2 (40 mm graded stone aggt) as in sub base etc complete all as specified & directed by Engineer-in-Charge.

Forming Construction joint 30mm deep x 10mm wide filled with mastic filling.

M&L for chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors over 20 mm thick screed bed in CM 1:6 jointed with grey cement slurry mixed with pigment to match complete all as specified and directed.

Taking down cement plaster/deteriorated concrete from bottom of RCC Chhajja/RCC facia/RCC beam/RCC slab/brick work including racking out joints, hacking for key, scrubbing down with water (at a bldg height upto 4.50 mtr) and removing rubbish to a distance exceeding 50mtr but not exceeding 100mtr away and M&L for 15mm thick plaster in CM 1:3 finished even and smooth without using extra cement on bottom of RCC Chajja & RCC facia complete all as specified and directed by Engr-in-Charge

Rough excavation not exceeding 1.5 m deep and getting out in soft/loose soil

Spreading and levelling, including watering as required and well ramming in layer n.exc. 25cm thick each layer complete all as specified and directed.

Excavation in trenches in soft and loose soil including cutting road surfaces not exc 1.5 mtr wide and not exc 1.5 mtr in depth for poles, stay, cable , pipe etc getting out complete all as specified and directed.

Returning, filling including spreading and well ramming in layers not exc 25 cm thick in soft loose soil all as specified and directed.

Removing excavation material exc. 50m and depositing where directed bt Engr-in-Charge at a level n exc. 1.5 m above the starting point.

M&L for PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

M&L for RCC M-35 design mix foundation, including raft footings, foundation beams, plinth beams, bases for column etc basement slabs, under reamed piles and mass concrete complete all as specified and directed.

M&L for RCC M-35 design mix beams, cantilevers, lintels, columns pillars, piers, posts, struts, chullah hoods, stair case, arches, domes, vaults, shell roofs, arch ribs, olded plates, slabs, balconies, canopies, deck slabs etc or in similar articles upto 12m height complete all as specified and directed.

Mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mils steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Mild steel TMT bars 5mm dia and over upto 10mm dia in stirrups, spacers and binders cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Formwork to sides of fair finished flat surfaces of concrete foundations, foolting, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter complete all as specified and directed.

Fair finished square, rectangular or polygonal form work to sides of pillars , posts, struts, columns and stanchions complete all as specified and directed.

Fair finished flat form work to sides and soffits of floor or roof beams, lintels, cantilevers, shelves including supports etc complete all as specified and directed.

M&L for 15mm thick cement plaster in CM 1:4 as on other than fair face of brick or concrete surface finished surface even and fair complete all as specified and directed. Note :- supply only water proofing liquid shal be measured and paid separately.

Preparing newly plastered surfaces of walls and applying two coats of cement base paint complete all as specified and directed.

S&F of rolled mild steel Gde Fe-410-S in roof trusses (framed) trussed, hollow section, anchorage paltes, purlins crane gantries, plates, rails & fastenings and heavy brackets framing (Beams, tee, angle, column, channel or flat section) etc including distance pieces, cleats etc with riveted, bolted or welded attachment upto 12m height complete all as specified and directged by Engr-in-Charge. Note :- Cost of formwork and welded mesh, bldg ht upto 12 mtr shall be deemed to be included in unit rate quoted by the Contractor.

S&F carbon steel (finished with blackodised/ hot dip galvanised ) L shaped anchor bolt/ foundation bolts ASTM F1554 Gde 55 screwed one end, with 2 hexagonal or square nuts and 2 washers the other end enlarged and jagged or lewised, but diameter of bolt 20mm and length of bolt 50cm long or as required at site complete all as specified and directed.

Excavating in post holes (or similar holes) each n. Exc 0.5cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25cm, watering and removing surplus soil to a distance n. Exc 50m and making good surface in any type of soil.

S&F MS posts and struts in fencing including cutting tops to shape as directed, drilling holes notching for wire etc; notching for wire etc; angle, flat iron filets ( for securing wire mesh etc) nincluding all necessary drilling, bolting or rivetting etc and similar work conforming to Fe-290 Fde E-165 complete all as specified and directed by Engr-in-Charge.

Supply & fixing 3 or 4mm dia PVC Coated galvanised mild steel chain link fencing of mesh size 75mm x 75mm fixed with string bolts complete all as specified and directed.

M&L for mild steel bolt( machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends each screwed end to be filled with washers and hexagonal or square nut, not exc 5cm long and diameter of neck 5 to 10mm complete all specified and directed by Engr-in-Charge.

S&F for mild steel framed work such as grills, gratings etc with ends of bars shouldered and/ or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed.

M&L for brick work with sub class "B" bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 complete all as specified and directed.

S&F ductiile iron centrifugally cast (span) pressure pipe class K-9 size 100mm ISI marked with internal cement mortar lining and external zinc and bitumen coated pipe 100mm bore with all spogot and socket ends with push on rubber gasket joint etc all as specified and directed.

S&F of GI tubing, medium grade, galvanised, with all fittings, laid in trenches of size 80mm bore complete all as specified and directed.

S&F of GI tubing, medium grade, galvanised, with all fittings, laid in trenches of size 50mm bore complete all as specified and directed.

Cutting of existing DI pipe of 100mm bore for insertion of new Tees, branches complete all as specified and directed.

Supply and fix in repair CI sluice valve with forged brass stem class P11-1.6 ISI marked with stainless steel spindal and flanged both ends of size 100mm dia bore with hand wheel complete all as specified and directed.

Supply and fix in repair CI sluice valve with forged brass stem class P11-1.0 ISI marked with stainless steel spindal and flanged both ends of size 80mm dia bore with hand wheel complete all as specified and directed.

M&L for ISI marked CI/DI pipe fittings upto size 80 to 200mm dia such as bends, Tapers tail pieces, Tee pieces, caps and

M&L of pits and constructing of brick masonary pits of internal dimensions 1 mtr x 1 mtr x 1.2 mtrs (bottomn PCC floor of the pit should be minimum 30cms below the bottom surface of sluice valve flange to provide sufficient working space, bottom floor of the pit be constructed in PCC (1:3:6) 15cms thick with 20mm stone aggregate, inner and exposed surfaces and bottom floor of the pit should be plastered in CM (1:4) 15mm thick. The sluice valve and other fittings should be housed in centre of the pit, the vertices of the pit should in right angle and champhered. The top cover of the pit will be made made out of MS sheet min 2mm thick with angle iron frame made out of MS angle 50mm x 50mm x 6mm with galvanised steel hingges two nos and locking arrangements duly painted with two coats of water resistant synthetic enamelled paint over one coat of red oxide.

E/M PORTION Taking down carefully aluminium/copper point wiring for light, fan, bell, socket of point complete fittings such as switches, ceiling roses, pendents, regulator socket etc complete at site and making goods disturbed surfaces of walls, floors etc.

Point wiring with PVC insulated and PVC unsheathed single core multistranded FRLS copper conductor cable of size 1.5 Sqmm including concealed PVC conduit with fittings and making good to the disturbed surfaces with continuous earth wire of PVC insulated and PVC unsheathed single core multistranded FRLS copper conductor cable of size 1.5 Sqmm to common earth including provn of 3mm thick plastic laminated sheet of appropriate size and fixing to and including CI/MS boxes for mounting of accessories like switch sockets and regulators etc. complete all as specified for One light / Fan/ bell point controlled by one way switch

All as per Srl item No 104 above but one light/ fan/ bell point controlled by one way switch

All as per Srl item No 104 above but one 5 pin socket outlet 5 amps on same board.

All as per item Ser No 104 above but cable size 2.5 sq mm , FRLS, for one socket 16A multipin on independent board

M&L for sub main wiring with two single core multi stranded PVC insulated, unsheathed copper conductor of grade 1100 Volt , FRLS cable of size 6 sqmm (red for phase and black for neutral) and including electrical grade PVC conduits of desired colour not less than1.2 mm thick and 32 mm wide & 6 sqmm multistranded copper conductor cable PVC unsheathed green coloured for earthing with complete accessories duly connected with earth duly complete and taking down old unserviceable one. Note :- (a) Cost of making good the disturbed surface plastering/filling putty alongwith matching with the existing colour with MES Approval make of distemper is deemed to be included in the quoted rate by contractor. (b) Three run of cable alongwith PVC conduit together shall be measured as single run.

S&F switch piano flush type single pole one way 5 amps

S&F socket outlet 3 pin 5 amps flush type

S&F switch flush type 15 amps single pole type one way

S&F socket outlet 3 pin 15 amps flush type

S&F in replacement surface mounting universal batten housing made of powder coated CRCA sheet suitable for and upto 1 x 18/20 W LED tube rod single sided in l taking down old unserviceable fitting complete all as specified and as directed.

S&F LED tube light 20W ultra bright LED polycarbonate tubelight with very high efficacy suitable for fitting into tube light batten fittingt all as directed Note :- The contractor will submit the LM-80 and LM-79 report from manufacturer to Engineer-in-Charge before incorporating the items in work.

Taking down carefully ceiling fan complete fittings at site removing Fans are deposited to MES storeyard and re-fixing after completion of work at the site .

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan complete including replacement of one pair of Canopy.

S&F in replacement of fan regulator electronic type 5 step 100watt, 240 Volt and connecting complete all as specified and directed all as directed.

S&F lamp holder PVC body angle type including 9 watt LED bulb polycarbonate body complete all as specified and directed.

M&L ceiling rose, three terminal/ Phase, PVC /Polycarbonate isolated body.

S&F in replacement GI pipe bracket made out of GI pipe light grade 32 mm dia and bend to shape 1.5 mtr long MS clamps made out of MS flat iron of size 32 mm thick with nuts & bolts, washers complete including dismentling the existing GI pipe bracket and drilling of holes for nuts & bolts etc all as specified and directed

Supply and fixing LED street light fitting 35 Watt 230V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

Supplying and fixed in repair sheet metal enclosure for DB’s when MCB’s to be used of 240 volt 8 way with 200 amps rated bus bar SPN double door complete all as specified and directed. Note : All the connection of incoming and out goiing wire in MCB will be made with thimble with suitable size as directed.

S& F in repair MCB single pole 6 amps to 32 amps, complete all as specified and directed.

All as per Item Ser No 123 here-in-before but single pole and neutral 32 amps, complete all as specified and directed.

Material and labour for replacement of distribution board made out of CRCA sheet DB vertical type double door TPN 4 Way MS sheet including fixing in the wall, cutting chases, grounting and necessary patch work and white wash to match with the existing including making connections all as directed containing the folowings:- Note :- All the connection of incoming and out goiing wire in MCCB and MCB will be made with thimble with suitable size as directed. (a) MCCB 4 Pole 63 Amps 16 KA breaking capacity with thermal release: 01 No (In coming). (b) Bus bar 200 amp rated made out of Aluminium on insulated duly insulated wire adhesive tape RYB & black :4 Nos. (c) MCB SPN 40 Amp- 4 Nos, MCB SP 40 Amp- 04 Nos (Out going). (d) Connection from MCCB to bus bar will be made with Aluminium Strip of suitable capacity as directed.

M&L Earthing complete with galvanised steel earth plate electrode 60cm ×60cm × 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised iron earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No.3 connected to earthing test point including testing on completion including watering GI pipe 20mm bore medium grade, 15mm bore light grade GI pipe for protection of earth lead including provision of concrete pit in PCC (1:2:4) type B1, pre-cast RCC (1:2:4) type B1 cover slab 54 cm x 54 cm x 5 cm including 8mm dia TMT bars both ways @ 15cm centre to centre with one handle for lifting made out of 8mm dia MS bar, funnel & wire mesh, excavation and earth work in any type of soil including testing, dismantling existing earthing complete all as specified & directed by Engr-in-charge.

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sq mm 3.5 core complete al as specified and directed.

Supply and lay brick common burnt sub class "B" old size for protection of cable laid in trenches for under ground cable all as specified.

M&L sand cushioning in trenches using fine sand to under ground cable, laid in two layers 15cm before laying the cable and 8cm after laying the cable complete all as specified.

M&L for cable protection GI tubing light grade fixed long the pole/under road/along the wall of size 40 mm bore with necessary clamps all as directed.

A Schedule of Credit for old/unserviceable demolished/dismantled items has been catered for in the tender. The Schedule of Credit is pre-priced by MES. The final amount of the tender shall be arrived at after deducting the total amount of Schedule of Credit from the total amount of BoQ as per General Summary sheet catered for after Schedule of Credit.

GORAYA AND CO (BID ID -3128411)

M/S DARSHAN & CO (BID ID -3128494)