SPECIAL REPAIR TO BLDG P110 JCO CLUBOF 167 MED REGT AT BMC UNDER GE CENTRAL KOLKATA

Amount

NOTES :(i)The bidders/contractors are advised to read tender document & all corrigendum/ amendments and General conditions of contracts before entry/quoting the rates. (ii) It is highlighted that the cretin condition of General Condition Of Contracts (IAFW-2249) has been modified as direction of MOD i.e inclusion of performance security, deletion of risk & cost provisions and increase in defects liability period all as specified in tender document. The tenderers should keep in mind while quoting their offer

Demolition of cement concrete (Un-reinforced) in ground floor and paving nexc 15cm thick above or below GL complete all as specified and directed

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Taking down existing water proofing treatment with padding upto original roof and removing the debris from the site etc complete all as specified and directed

Demolition of brick work or stone masonary built in cement mortor including all quoins & jambs etc. complete all as specified and directed

Taking down cement plaster of any description on brick work or stone msonary wall including racking ot joints hacking for key scrubbing down with water etc. complete all as specified and directed

Taking down chowkhats or frames with shutters (without taking off shutter from frames) of any sizes nexc 1.5 Sqm each complete all as specified and directed

All as item No. 07 here in before but exc 1.5 Sqm and nexc 4.0 Sqm each.

Dismentalling floors hearth or wall tilling including cement mortor bedding (but not backing) removing serviceble tiles to store and rubbish off the premises complete all as specified and directed

Taking up or down steel tubing 15mm dia bore including all connection complete all as specified and directed

All as per item No. 10 here in before but 20mm dia bore.

Anti Termitet treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed

Anti Termite Treatment of voids in masonry using chemical emulsion one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and directed

Chipping of unsound /weak concrete materials from slabs , beams,columns ,lintel,chajja, fin , facia etc. (upto 30mm average thickness for slabs/Chajja) by any means as directed by engr-in-charge including tapering all edges, making square shoulders of cavities air or sand blasting etc and cleaning of exposed concrete surface of lightly picking materials by air blasting or sand blasting incl foreign matrials , loose concrete/aggregate etc and disposal of all debris out of MOD land and complete all as specified and as directed by Engr-in-Charge ( upto 4 storey of building)

Drilling holes of 20 mm diameters in reinforced or plain cement concrete to a minimum depth of 150mm and upto 200mm including power drilling,fixing the reinforcement in position using epoxy, cleaning of loose dust by blowing air, sealing with epoxy cartridges etc all as specified and directed. Make :- Hilti HY 150/ Fosroc Lockfix E 75 chemical or quivalents solutions SIKA /STP/ HINDCON as approved by GE.

Supply and fixing Welded steel wire fabric weight not more than 4Kg/Sqm fitted by ms nails complete all as specified and directed

Removing of concrete all around reinforcement bar upto 12 mm dia from behind the reinforcing bars average 25mm (but not less than 15mm air gap)by manual methods (using wire brushing ,chiselling etc) and applying chloride free rust removing chemical on rusting steel reinforcement bar and removing all rust from steel reinforcement bar by emery paper and cleaning the area throughly by water and allow it to dry and totally rust free of reinforcement bar including all necessary scaffolding,complete all as per manufacturer's instruction and as directed.(only area of cleaned steel bar shall be measured for payment). Make( Rust removing chemical ):- Reebaklens RR of FOSROC or quivalents solutions SIKA/STP/HINDCON as approved by GE.

Material and labour for application of anticorrosive paint on cleaned reinforcement as per manufacturer's specification including preparation of surface complete as per direction of Engineer-in-Charge Note : Payment to be made on 25% of exposed area Make :- Hind Anti Rust (M/s Hindcon) or equivalent from M/s Pidilite/Forsoc

Providing and applying two component epoxy bonding agent (Mixed density : 1.48Kg/ltr, adhesive bond strength to be >2.50 MPs) for bonding fresh wet cementitious materials to existing cementitious surfaces bonding agent of approved brand including all necessary scaffolding, complete all as per manufacturer instruction Make :- Nitobond EP (Std) of FOSROC or equivalents chemical of SIKA / STP / HINDCON as approved by GE.

Application of polymer modified concrete with mix ratio 1:1.5:3 (1 cement : 1.5 Coarse Sand : 3 Stone aggregate of 10mm nominal size) admixed with acrylic latex polymer @ 2.00 Kg per Sqm and plasticiser @ 100Gms.Sqm for an average thickness of 50mm (the concrete to be applied when the bonding coat is still green) including necessary scaffolding and formwork etc. as per manufacturer's specification and direction of Engineer-in-Charge Make : (a) Acrylic latex polymer : Hind Styrene BR /Nitobond SBR (M/s Hindcon) or equivalent from M/s Pidilite/Forsoc (b) Plasticiser :- Hind Plast Super/Conplast SP 337 (M/s Hindcon) or equivalent from M/s Pidilite/Forsoc

Material and labour for pressure guniting 40mm thick at a pressure not less that 6Kg/Sqcm to surface of column, beam, ceiling and similiar structural members in cement mortar 1:3 duly modifing the mortar with polymer mortar @ 7.00 Kg for 50 Kg bag of cement per Sqm and and plasticiser @ 400Gms (the mortar to be applied when the bonding coat is still green) including necessary scaffolding and formwork etc. complete all as per manufacturer's specification and direction of Engineer-in-Charge Make : (a) Polymer mortar :- Hind Styrene BR/Nitobond SBR (M/s Hindcon) or equivalent from M/s Pidilite/Forsoc (b) Plasticiser :- Hind Plast Super/Conplast SP 337 (M/s Hindcon) or equivalent from M/s Pidilite/Forsoc

Use and waste for formwork to sides and soffits of floor or roof beams, beam haunch- ings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for rough finished surfaces complete all as specified and directed

Use and waste for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings, shelves and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed

Material and labour for for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clip complete all as specified and directed

All as per item No. 24 here in before but 6mm to 8mm dia bars

All as per item No. 24 here in before but 6mm to 10mm dia bars as in stirrups, spacers and binders

Material and labour for RCC M-25 design mix as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed

Material and labour for RCC M-25 design mix as in slabs supported on walls,beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed

Material and labour for fly ash pulverizes bricks using class 'A 'old size bricks straigth or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified and directed.

All as item No. 29 here in before but half brick thick brickwork built in CM 1:4 complete all as specified and directed.

Material and labour for 15mm thick rendering in CM (1:4) on fair faces of brick work or concrete surfaces finished the surfaces even and fair without using extra cement and using water proofing compound as per manufacturer instruction complete all as specified and directed

Material and labour for applying 20mm thick polymer modified cement mortar rendering in CM 1:3 on wall duly mixing polymer modifier @ 7 Litre per bag of cement complete finished even and smooth without using extra cement complete all as specified and as per manufacturer's specification. Make : Nitobond SBR of M/s Forsoc Chemical India (Pvt) Ltd or Hind Styrene BR of Hindcon Chemical Ltd or equivalent make of M/s Pidilite Industries

Material and labour for 15mm thick rendering in CM (1:6) on other than fair faces of brick work or concrete surfaces even and smoth without using extra cement complete all as specified and directed

Material and labour for 5mm thick rendering in CM (1:3) as in ceiling surfaces finish even and smoth without using extra cement complete all as specified and directed

Supply only liquid water proffing compound complete all as required

Material and labour for for Pressed steel frames of size 125 x 60 mm (fabricated out of CRLCS sheet 1.6 mm thickness) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and directed. Note :- Pressed Steel Frame should be filled with PCC 1:3:6 Type C-0 (Using 12.50 mm graded stone aggregate) and cost of PCC shall deemed included in quoted rate.

All as per item no 36 here-in-before but size of frame 105 x 60 mm complete all as specified and directed.

Material and labour for for PCC 1:3:6 type C-1 using 20mm graded stone agg as in bed blocks/hold fast including necessary form work complete all as specified and directed

Supply and fixing 30 mm thick flush shutters, factory made ,solid core construction, with block board core and plywood face panels, incl 3 mm thick Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on both faces; fixed with screws to timber frame work complete all as specified and directed.

Supply and fixing second class hardwood 35mm thick glazed skeleton shutters,factory made, open rebated and prepared to recive glass, gauze, etc. (without sash bars), edges of framing plain, chambered or rounded. fitted with cut and mitred beads for securing glass, etc. sizes of me-mbers of shutters as specified in SSR part-I section 8 clause 8.24 (a) supplied and fitted to chowkats all as specified and directed.

Supply and fixing for Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

Supply and fixing Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. Square tube, complete all as specified and directed.

Supply and fixing for factory made Solid PVC Moulded door shutter with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain moulded PVC Sheet polyurethane painted on the front face & 2mm prelam PVC Sheet on back face, complete all as specified and directed.

Supply and fixing powder coated aluminum frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified & directed. Note : (a) Thickness of aluminium section shall not be less than 1.5 mm. (b) Anodizing shall be 15 micron conforming to IS-1868-1996 (c) Minimum thickness of powder coating 50 micron

Supply and fixing powder coated aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, alluminium snap beading, screws, etc. complete all as specified & directed. Note : (a) Thickness of aluminium section shall not be less than 1.5 mm. (b) Anodizing shall be 15 micron conforming to IS-1868-1996 (c) Minimum thickness of powder coating 50 micron

Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Supply and fixing of tinted glass with sheet glass 4.80mm thick , pin head type and glazing in squares exc 0.5 sq. M in each pane complete all as specified and as directed.

Supply and fixing factory made uPVC ventilator, white colour, fixed type partly glazed with and including 3 mm thick frosted glass pane and partly gauged with and including 0.36 mm dia and 1.4 mm aperture stainless steel wire net, ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriatedimension, EPDM gasket, G.I. fasteners 100 x 8 mmsize for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per direction of Engineer-in-Charge.

Material and labour for drapery rod made of electric resistance welded MS pipe of 21mm dia having a coating of corrugated virgin PVC extrusion and cover with ABS plastic complete all as specified and directed.

Supply and fixing end finials for drapery rod and including closed type stainless steel all brackets fixed on wall complete all as specified and directed.

Supply and fixing 100 mm butt hinges heavy duty, cold rolled mild steel medium weight complete all as specified and directed

Supply and fixing stainless steel barrel tower bolt 200mm long complete all as specified and directed

Supply and fixing stainless steel sliding door bolt 300mm long with haps and staples (bolt type) and fixing clips of sheet and fixing bolts and sliding bolts complete all as specified and directed

Supply and fixing stainless steel handle "D" type 150mm long complete all as specified and directed

Supply and fixing floor door stopper anodised, with hard down steel spring, fixed in floor complete all as specified and directed

Supply and fixing Aluminium (extruded section body) Door closer hydraulically regulated, designation No. 1 universal type, suitable for door shutters up to 700 mm in width and of weight not more than 35 kg and fixed complete all as specified and directed

Material and labour for 12 mm thick Medium density fibre board, exterior grade, fixed to timber framework with screws complete all as specified and directed.

Supply and fixing Continuous (Piano) hinges, mild steel, bright finished or electro galvanized, width of flaps (When open) 20 mm complete all as specified & directed

Supply and fixing 40mm dia cupboard knobs fixed with nut screws and washer of wooden finish brass polished complete all as specified and directed.

Supply and fixing 300mm, ordinary mild steel rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

Supply and fixing for Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work complete all as specified and directed.

Material and labour for 75mm thick PCC (1:3:6) type C-2 (Using 40mm graded stone aggregate) as in plinth protection laid in panels, finish the top surfaces even and smooth without using extra cement complete all as specified and directed Note:- Construction joints will be provided at interval of 2.5m length and filled with bitumen 80/20 mix with sand in ratio of 1:3 and cost of the same shall be deemed included in quoted rate

Material and labour for 100mm thick PCC (1:2:4) type B-2 (Using 40mm graded stone aggregate) as in sub base of path/hard standing etc complete all as specified and directed.

Material and labour for 75mm thick PCC (1:4:8) type D-2 (Using 40mm graded stone aggregate) as in sub base of floor complete all as specified and directed

Material and labour for 25mm thick PCC (1:2:4) type B-0 (using 12.50mm graded stone aggregate) as in sub base of floor complete all as specified and directed.

Material and labour for joint free non skid ceramic coloured tiles 8-10mm thick (square/rectangular) area of each tile exc 0.18 Sqm but not exc 0.38 Sqm in floor set and jointed in in neat cement slurry and pointed in cloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed

All as item No. 66 here in before but in skirting with and including 10mm thick rendering on fair faces of brickwork in CM 1:4 complete all as specified and directed.

Material and labour for joint free non skid ceramic coloured tiles 7-8mm thick (square/rectangular) area of each tile exc 0.06 Sqm but not exc 0.11 Sqm in floor set and jointed in in neat cement slurry and pointed in cloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed

Material and labour for glazed ceramic coloured tiles 450x300x6-7mm in vertical surfaces set and jointed in in neat cement slurry and pointed in cloured cement to match over and including 10mm thick rendering in CM 1:4 complete all as specified and directed

Material and labour for Machine cut kota stone slab flooring 20-25mm thick over 20mm thick screed base in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed

Material and labour for granite slab 18 to 20mm thick of any type work table rubbed and polished in kitchen platforms and like over and including cement screed bed 20 mm thick in CM (1:6) bedded and jointed with grey cement slurry and pointed with white cement mortor (1:2) using marble dust with admixture to match with shade of granite complete all as specified and directed

Material and labour for heavy duty exterior vitrified tiles (full charged) of size 300x300x7-10mm thick as in floor with & including screed bed 15mm thick in CM 1:4 set and jointed in neat cement slurry & pointed in coloured cement to match complete all as specified and directed.

Supply and fixing 20 mm bore (Outer dia) CPVC pipes of SDR 11and plain CPVC SDR 11 fitting fixed on wall or floor, ceiling or laying in floors with necessary clips complete all as specified and directed by Engr-in-Charge .

All asper item no 73 here-in-before but 25 mm bore (Outer dia) complete all as specified and directed by Engr-in-Charge .

All asper item no 73 here-in-before but 40 mm bore (Outer dia) complete all as specified and directed by Engr-in-Charge .

Cutting chase, pinning in making good to facing where required and pointing in CM 1:3 to end or edges of landing steps, cills, sunshades, shelves, lintels etc. and cutting chase for conceled water pipe etc. and making good cutting not exc 10Cm girth complete all as specified and directed.

Supply and fixing in repairs vitreous china (coloured) wash down water closet pan (pedestal pattern) with 'P' or 'S' trap front or back inlet, fixing bolts(except flushing cistern and flush pipe) incl plastic water closet seat cover (coloured) and mild steel chromium plated or aluminium hinging device complete all as specified and directed by Engr-in-Charge. Make : Parryware (Model: Verve), Cera(Model : Celeb) , Hindware (Model : Superb S)

Supply & fixing in repairs vitreous china wash hand basin, white, flat back, size 550mm x 400mm excluding chain and plug and porcelain stopper but including cutting for and pinning in ends of and including brackets, waste pipe & CP brass waste coupling of 32mm dia ,pvc connection 600 mm complete all as specified and directed. Note : Rate quoted under this item deemed included fixing of taps, plug and chain and connecting up to supply pipes, wastes or traps etc. Make : PARRYWARE ( Cat no : C0406 ), HINDWARE( Cat No- 10010), JAQUAR (Cat no -CNS-WHT-801), CERA (Cat no- S2040141)

Supply and fixing in repair 10 litre capacity, PVC valve less syphonic action type, flushing cistern, low level, white, with inlet, ball valve, flush pipe, float and handle including brackets complete all as specified and directed. (upto 04 storey High of building). Make : PARRYWARE ( Model no : Slim line Economy), HINDWARE( Model No- Sleek Plus), CERA (Model no- Corona), PRAYAG (Model No : SMART) or equivalent Model in COMMANDER.

Supply and fixing in repair 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to wall complete all as specified and directed.

All as per item No. 80 here in before but double socketed complete all as specified and directed.

Supply and fixing in repair PVC (SWR) bend any radius 110mm bore complete all as specified and directed

Supply and fixing in repair PVC (SWR) junction single (single T) equal or unequal 110mm bore complete all as specified and directed.

Supply and fixing in repair UPVC (SWR) floor trap plain , diameter of outlet 75mm with grating including jointing with solvent cement complete all as specified and as directed

Supply and fixing in repair 15mm bore brass chromium plated Wall Mixer with provision for Overhead Shower with 190 mm long Bend Pipe on Upper Side, Connecting Legs & Wall Flanges complete all as specified and directed. Make : Essco (TM-115) or equivalent from Hindware (Cat. No.: F330020) ,Parryware (G3416A1)

Aupply and fixing in repair for brass chromium plated Centre Hole Mixer for WHB screwed for 15 mm bore pipe complete all as specified and directed Make : Essco (TM-107A) or equivalent from Hindware ( Cat. No.:F740009), PARRYWARE (G1414A1)

Supply and fixing in repairs 15mm bore Brass CP angular stopcock concealed type with crutch or butterfly handle complete all as specified and as directed by Engineer-in-Charge. Make:- JAQUAR (Cat No: FUS-29053), PARRYWARE (Model No: G4807A1) , CERA (Cat No: F1015361), HINDWARE(Cat No: F360006), PRAYAG (Cat No : 9010)

Supply and fixing in repair 15 mm bore bib taps, cast copper alloy fancy type chromium plated with capstan head screwed down , screwed for iron pipe of 15 mm bore and fixed , complete all as specified and directed Make:- JAQUAR (Cat No: FUS-29037), PARRYWARE (Model No: CLARET), CERA (Cat No: F1015151), HINDWARE(Cat No: F360004), PRAYAG (Cat No: 9306-N), ASIAN PAINTS (Cat No : ALBC101).

Supply and fixing in repair for brass chromium plated two in one tap with Wall Flange screwed for 15 mm bore pipe complete all as specified and directed Make : Essco or equivalent from Hindware ,Parryware,Cera

Supply and fixing in repair for brass chromium plated long body bib cock with Wall Flange for 15 mm bore pipe complete all as specified and directed. Make : Essco or equivalent from Hindware ,Parryware,Cera

Supply and fixing in repairs chromium plated ABS body round over head Shower roses with arm(premium quality) , multi flow,including fixing to 15 mm bore pipes or union complete all as specified and as directed by Engineer-in-Charge. Make:- JAQUAR (Cat No:OHS-1789 for shower and SHA-477 for arm ), PARRYWARE (Model No: T9986A1 for shower and T9802A1 for arm ) , CERA (Cat No: F7020305CH for shower and F7040105 for arm), HINDWARE (Cat No: F160008 for shower and F330028 for arm)

Supply and fixing in repair for shower arm 195 mm long round shape with flage including fixing to steel pipe or union complete all as specified and directed Make :Hindware or equivalent from Essco ,Parryware,Cera

Supply and fixing in repair 600mm long Towel Rail chromium plated fixed with screw complete all as specified and directed

Supply and fixing in repair PVC bathroom cabinet (white) of size 430 x 330 x 100 mm (approx) with one single shutter and built in mirror in front of shutter complete all as specified and directed. Make - Prayag (Cat No. 551) or equivalent make as mentioned in PS

Supply and fixing in repair of stainless steeel of 304 grade of kitchen sink of overall size 495mmx420mm and bowl size 410mm x330mmx160mm depth or equivalent made of 1mm thick stainless steel sheet with 32mm bore CP waste coupling including ball and chain 300mm long with bass cap rubber plug, 32mm bore PVC waste pipe (heavy duty) 90cm long, and bedded in cement mortar and fixed in CP cantilever brackets complete all as specified & directed. Make:- Bluestar/Nirali/Prayag

Supply and fixing PVC connection 15mm size with PTMT nut of length 450mm complete all as specified and directed

Supply and fixing in repair health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified & directed. Make : JAQUAR ( Cat no : ALD-CHR-593 ), CERA ( Cat No- F8030401AB), HINDWARE (Cat no -F160013), PARRYWARE (Cat no- E8352A1)

Supply, hoisted and fixing in position 1000 Ltrs capacity rotational moulded polyethylene water storage tank, double layer construction, ISI mark (cylindrical vertical with closed top) hoisted and fixed in position with and including 20 mm dia GI pipe medium grade washout pipe 450 mm long with plug and 20 mm dia GI pipe medium grade overflow pipe 600 mm long with fittings including 25 mm ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed(minium weight 15 mm - 210 gms) complete including dismental of old water tank and removing from site. complete all as specified & directed.

Material and labour for preparation of old decorated surface by complete removal of existing treatment, washing, rubbing, stopping etc and applying two coats of acrylic washable distemper over a coat of alkali resistant primer including applying one or more coat of wall care putty to a smooth surface including making good any undulations on the surfaces complete all as specified and as directed. Note :- (i) Painting work shall be carried out acoording to Smart Painting procedure mentioned in PS (ii) Painting work shall be carried out directly through a paint manufacturer as approved by GE or their approved applicator. (iii) After completion of work approved paint manufacturer or their approved applicator shall submit warranty for one year on workmanship and warranty on product as applicable. .

Material and labour for preparing newly plastered surfaces of internal walls, etc and applying two coats of acrylic washable distemper over a coat of alkali resistant primer including applying one or more coat of wall care putty to a smooth surface including making good any undulations on the surfaces complete all as specified and as directed. Note :- (i) Painting work shall be carried out acoording to Smart Painting procedure mentioned in PS (ii) Painting work shall be carried out directly through a paint manufacturer as approved by GE or their approved applicator. (iii) After completion of work approved paint manufacturer or their approved applicator shall submit warranty for one year on workmanship and warranty on product as applicable. .

Material and labour for preparation of old decorated surface by complete removal of existing treatment, washing, rubbing, stopping etc and applying two coats of weather proof exterior emulsion paint over a coat of alkali resistance primer including applying one or more coat of wall care putty to a smooth surface including making good any undulations on the surfaces complete all as specified and as directed. Note :- (i) Painting work shall be carried out acoording to Smart Painting procedure mentioned in PS (ii) Painting work shall be carried out directly through a paint manufacturer as approved by GE or their approved applicator. (iii) After completion of work approved paint manufacturer or their approved applicator shall submit warranty for one year on workmanship and warranty on product as applicable. .

Material and labour for preparation of new platered surface of wall and applying two coats of weather proof exterior emulsion paint over a coat of alkali resistance primer over 2 mm thick exterior wall care putty including all necessary scaffolding,complete all as specified and directed. Note :- (i) Painting work shall be carried out acoording to Smart Painting procedure mentioned in PS (ii) Painting work shall be carried out directly through a paint manufacturer as approved by GE or their approved applicator. (iii) After completion of work approved paint manufacturer or their approved applicator shall submit warranty for one year on workmanship and warranty on product as applicable.

All as per item no 99 here -in-before but as in ceiling surfaces complete all as specified and directed.

All as per item no100 here -in-before but as in ceiling surfaces complete all as specified and directed.

Material and labour for preparation of new surfaces of wood and wood based materials of any descriptions not otherwise described over 10Cm width or girth & applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Material and labour for for preparation of new surfaces of steel and steel based materials of any descriptions not otherwise described over 10Cm width or girth & applying two coats of synthetic enamel paint over a coad of red oxide primer complete all as specified and directed

Material and labour for 50 mm thick PCC(1:2:4) type B0 (using 12.5 mm graded stone aggregate) for padding concrete as on roof complete all as specified and directed by Engineer-in-Charge.

Material and labour for 15 mm thick (average) screed bed in CM (1:3) on concrete surfaces on roof, mixed with water proofing compound and finishing the surface even and fair without using extra cement complete all as specified and directed (Water proofing compound shall be measured and paid seperately).

Material and labour for water proofing treatment on existing cleaned RCC roof with the following specification and manufacturings instruction complete all as specified and as directed:- ((a) Preparing and clening of fully dry surfaces as per IS3067-1966 (b) Applying bitumen primer conforming to IS:3384-1968 over the cleaned plaster surface @ 0.5 Ltr per sqm (c) Applying a layer of APP based polymeric membrance 3.0mm thick (minimum) weight 3.6 Kg per sqm (reinforced) with polyster Non woven fabric weighing not less than 160gms per sqm by torch application. (c) Applying a tack coat of industrial bitumen 85/25 at the rate of 1.2Kg per sqm including cleaning surface. (d) Applying protective coating with bituminous based aluminium paint @ 0.2kg per sqm in two coats compete all as specified and directed.

Material and labour for cement concrete tiles 20cm x 20cm x 20mm thick, machine pressed; set jointed and pointed in neat cement slurry in roof surfaces, made from grey cement with no pigment with and including 15mm thick screed in CM 1:4 complete all as specified and as directed.

Material and labour for 50 mm thick louvres and jallie in precast cement concrete 1:2:4 type B-0 (using 12.50mm graded stone aggregate) , including all mouldings but excluding frame and set in cement mortar 1:4 complete all as specified and directed

Excavating in trenches, not exceeding 1.5 metres wide and not exceeding 1.5 metres depth for foundation etc and getting out in soft / loose soil complete all as specified and directed

Returning, filling in incl spreading, levelling, watering and well ramming in layers not exceeding 25cm in soft / loose soil complete all as specified and directed

Removing excavated material (soil of any type) n.exc 50m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed

Material and labour for PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation base of poles and other similar locations including demolition of old PCC / broken PCC complete all as specified & directed

Material and labour for for PCC (1:3:6) type C-2 using 40mm graded stone aggregate with and including all necessary form work including demolition of old PCC / broken PCC complete all as specified & directed

Taking out existing pipe line of any type from trenches, walls, floors etc including cleaning of refixing or removal of unserviceable pipe from site all as directed:- (a) 25mm bore GI pipe

(b) 40 mm bore GI pipe

(c) 80mm bore GI pipe

Supply and laying GI pipe medium grade with all fittings in trenches:- (a) 25mm bore GI pipe

(b) 40 mm bore GI pipe

(c) 80mm bore GI pipe

Supply & fixing in repair 25mm bore gun metal gate valve (ISI marked) screwed down high pressure with handle with iron wheel both ends screwed for iron pipe complete all as specified & directed.

Materials and labour for construction of brick masonary valve pit chamber of size 1050 x 1050 x 1050mm internal dimension using sub class - 'B' bricks in CM (1:6) ,15 mm thick plastring in cement mortar (1:4) externally & internally extended to 15cm below ground level including 100 mm thick in PCC bed in cement concrete 1:3:6 type C2 with MS frame fabricated by angle of size 40 x 40 x 6mm complete with top cover of 3mm thick MS sheet & locking arrangement and painting with two coats of synthetic enamel over a coat of red oxide primer including demolition of old unserviceable damaged valve pit complete all as specified & directed.

Material and labour for Cutting / boreing of existing road / path, hardstanding etc for taking out cable and water pipe to protection with iron cover plate for passing cable, water pipe and making good the disturbed road top surfaces with following cement concrete all type, using of suitable depth and finished with speed breaker complete all as specified & directed by Engineer-in-Charge.

Supply and laying dry coarse sand as in cushioning of under ground electric cable in trenches, laid to a uniform thickness of 23cm (15 cm under the cable & 8 cm over the cable) and gently punned down to 18 cm thickness complete all as specified & directed by Engineer-in-Charge. Note:- Thickness after punning down shall be measured for payment.

Material and labour for sub class ‘B’ bricks, laid flat, dry in trenches to the width equal to the width of the brick as in cable protection complete all as per specified and directed.

Taking down copper/ aluminium point wiring (light, fan, buzzer, socket or power) complete including fixture and fittings such as switches, ceilling roses, pendants , regulators, sockets etc (excluding light fitting) at site for reuse of serviceable items and removal of unserviceable items from site and making good disturbed faces of walls, ceiling, floor etc to match with the existing surface complete all as specified and directed by Engineer-in-Charge.

Material and labour for Point wiring with PVC insulated and unsheathed FRLSH cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts grade cable conforming to IS-694 1990 drawn through and including PVC casing and caping of suitable size with all accessories including fabricated MS terminal boxes fixed flush with wall surface with 3mm thick plastic masonite laminated sheet top cover fixed with cadmium screw for mounting switches, sockets, regulator etc including 1.5 Sqmm multistranded PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as spcified for one light / fan / bell point / 3 pin 5 Amps socket outlet independent point controlled by one switch single pole one way complete all as specified & directed

All as per item No 129 here-in-before but One 3 pin 5 Amp socket outlet on independent board

All as per item No 129 here-in-before but One 3 pin 5 Amp socket outlet, on the same board with other switche with casing caping / PVC conduit complete all as specified and directed by Engineer-in-Charge.

All as per item No. 129 above but wiring with FRLSH PVC insulated ,sheathed multistranded copper conductor cables of size 2.5 sqmm and cables of size 2.5 sqmm as continuous earth wire for 5 pin 15 Amp socket outlet controlled by one switch on independent board complete all as specified and directed.

Supply and fixing switch piano flush type, single pole, one way, 5 Amp complete all as specified and directed. Make:- Anchor Product Code No 14111 / Legrad Cat No - 677200 / Havells Cat No - AHFSXXW101

Supply and fixing switch socket combination multipurpose 3 Pin, 16 Amp and 6 Amp controlled by one switch flush type complete all as specified and directed. Make:- Anchor Cat No 14614/ Legrad Cat No - 673042 / Havells Cat No - AHLKCXW163

Supply & fixing switch socket outlet 5 pin, 6 Amps, 230 volts flush type complete all as specified and directed. Make:- Anchor Cat No 14304/ Legrad Cat No - 675550 / Havells Cat No - AHLHCXW 155

Supply & fixing for lamp holder, PVC / Polycarbonate type with back plate suitable for batten fittings after taking down old U/S complete all as specified and directed. Make:- Anchor Cat No 39538/ Orient Cat No - 45WA000316 / Havells Cat No - AHLHAMW000

Supply and fixing ceiling rose, surface bakelite, 65 x 50 mm, three terminals complete all as specified and directed. Make:- Anchor Cat No 39040/ 3290/ Legrad Cat No - 30196 / Havells Cat No - AHLHXCW000

Supply & fixing energy efficient tube light fitting 10 watt with LED fittings of capacity 10 W suspended type /wall mounted type complete with LED tube lamp and fitting with copper flexible PVC cable of 0.50 Sqmm twin core not more than one metre in length after taking down olf U/s complete all as specified and directed. Make:- Crompton Cat No LDL-10WW / Havells Cat No - ENDURALINEARNEOB S10W LED830SPCWH / Bajaj Cat No - BCLSB 10 WH

Supply & fixing energy efficient tube light fitting 20 watt with LED fittings of capacity 20 W suspended type /wall mounted type complete with LED tube lamp and fitting with copper flexible PVC cable of 0.50 Sqmm twin core not more than one metre in length after taking down olf U/s complete all as specified and directed. Make:- Crompton Cat No LDL-20WW / Havells Cat No - ENDURALINEARNEOBS 20WLED865SPCWH / Bajaj Cat No - BRTX 20W LED 4F

Supply & fixing LED lamps of 30 watts bldg security light IP 66 power coated pressure die cast aluminium compact high power LED street light with compact size & rough design after taking down old U/s complete all as specified and directed. Make:- Bajaj Cat No - ENXT P 30L WH SY PC SD 30W LED / Crompton Cat No LSTS-30-CDLM / Havells Cat No :- ENDURACITYLITEPLATPUSSL30WLED757SASYBOPC

Supply & fixing LED bulk head fittings vistaglow robust & reliable surface and wall mounted application taking down old U/s complete all as specified and directed. Make:- Philips WT140W LED7S CW PSU S1 PC 9405 / Crompton Cat No - LT8-865-(2)/ Baja Cat No - BLTB 15W CWC

Supply and fixing ceiling fan regulator electronic step type, solid state, 240 volts complete all as specified and directed. Make:- Anchor Product code 14502 / Havells Cat No - AHFRFXW004 / Legrad Cat No - 677236

Taking down of Submain wiring upto 10 Sqmm or part of wiring of any description complete all as specified and directed.

Material and labour for sub main wiring with two runs single core 6 Sqmm (Nominal Area) FRLSH PVC insulated & unsheathed multistranded copper conductor cable LT 1100 volts grade drawn through and including PVC conduit not less than 25mm dia with all fittings fixed on surface of wall / ceiling with all necessary fittings and accessories and one run of FRLSH PVC insulated & unsheathed single core cable with multistranded copper conductor of size 6 sqmm as earth wire(green in colour) connected to commom earth dolly including taking out old sub main wiring complete all as specified and directed. Note : PVC Conduits/Casing-caping, two run cables and one run of earth wire will be measured as one length.

All as per Item No.144 here-in-before but with 2 run of 10.0 Sqmm cable and 10.0 Sqmm as earth continuity conductor.

Taking down unserviceable rusted / damaged MCB DBs of any type and way along with any type MCB and keeping serviceable MCB in safe custody in re-use in the work and making good to the disturbed surfaces of walls etc complete all as specified and directed.

Supply and fixing MCB SPN DB made up with sheet metal double door, phosphorised, power coated, neutral link, earth bar and din rail, 4 way with 200 Amps rated bus bar, 240 Volts complete all as specified and directed.

All as per item No 147 here-in-before but MCB SPN DB with 8 way 200 Amps rated bus bar specified and directed.

All as per item No 148 here-in-before but MCB SPN DB with 12 way 200 Amps rated bus bar complete all as specified and directed.

Supply & fixing MCB 6 to 32 Amps, SP, 240 Volts, B-Curve breaking capacity 10 KA complete all as specified and directed.

Supply & fixing MCB 6 to 32 Amps, DP, 240 Volts, B-Curve breaking capacity 10 KA complete all as specified and directed.

Supply and fixing MCB TPN DB made up with sheet metal, phosphorised, power coated, neutral link, earth bar and din rail, 8 way TPN with 200 Amps rated busbar, 240 volts complete all as specified and directed.

Supply and fixing MCB FP 63 Amps, 415 Volts, C-Curve, breaking capacity 10 KA as directed by Engineer-in-Charge.

Supply and laying XLPE insulated PVC sheathed, armoured, aluminium conductor cable 1100 Volt grade 50 Sqmm 3.5 core in duct / floor / wall with provision of saddle an dlugs, joints etc including connection complete all as specified and directed by Engineer-in-Charge.

Supply and fix LED decorative post top lantern, 36 Watt capacity for energy efficient conservation upto 50% and with eco friendly lighting system with all accessories and necessary connection including taking down old unserviceable one complete all as specified and directed. Make:- Surya Cat Part No SLEPT 40W-ETPP / Havells Cat pat No - RUBYPT35WLED 830PSYMTOPC / Bajaj Cat Part No - BGCL 40W

Taking down and opening the ceiling fan upto 1400mm sweep for inspection, removing bush / bearing, cleaning of bush / bearing, repairs to shaft including lathe work and grinding as required complete including minor spare parts replacementt such as split pin, rubber reel, nuts bolts and PVC canopy including reassembling and refixing of fan at its own position complete all as sirected by Engineer-in-Charge.

Rewinding of fan motor with super enamelled copper winding wire of suitable size & varnishing including testing of fan after rewinding complete all as specified & directed.

Material and labour for painting of ceiling fan / wall fan / exhaust fan of any size and sweep complete with synthetic enamel paint by spraying including filling with cavities with filer after cleaning all dust etc complete all as specified and directed

Materials and labour for Earthing complete with galvanized steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to GI wire 4mm as earthing lead by means of boths, nuts, check nuts and waasheres of GI or steel, GI strip protected by 40mm bore light grade GI pipe and other end connected to earth test point as directed including funnel with watering pipe 20mm bore light grade galvanised iron, wire mesh, charcoal or coke common salt laid in alternative layer of 15cm (complete thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C1, 50mm thick pre-cast RCC (1:2:4) type B1 normal mix cover slab reinforced with 8mm dia TMT bar 10 10 c/c bothways and single handle of 10mm dia round bar including necessary excavation, earth work etc in soft / loose soil and disposal of soil to a distance n.exc 50m and necessary testing on completion all as shown in electrical plate No 3 MES Schedule Part-I complete all as specified and directed

Note: Schedule of credit (SCHEDULE OF CREDIT) amount of Rs ________ mentioned on Page No ____ shall be deducted from the total quoted amount of BOQ.

BHAUMIK CONSTRUCTION

ROY CONSTRUCTION

JHAWAR SUPPLIERS