SPL REPAIR TO BLDG NO P-332/01 TO 04 (JCO GOVT MD ACCN) OF STN HQ AND SPL REPAIR TO BLDG NO P-334/01 TO 04 (JCO GOVT MD ACCN) OF ASC (SUP) TYPE A AT ITARANA MIL STN ALWAR

Amount

Demolition of brick/stone masonry built in cement/lime mortar of any mix including all quoins pillar ashlars masonry and removal complete all as specified& directed by Engr-in-Charge.

Demolition of cement concrete (un-renforced) in ground floor and paving n' exc. 15 cm thickness (below or above ground level.) & removal of rubbish material complete all as specified& directed by Engr-in-Charge.

Dismantling of stone slab and tiles of any description or thickness in floors, aprons etc laid, beded and pointed in any mortar including removing the dismantled material complete all as specified and as directed.

Taking down Chowkatts or frames with shutters ( without taking off shutters from the frame exc 1.5 sq. m but n exc 4 sq m each & removing to store.

Taking down Chowkatts or frames with shutters ( without taking off shutters from the frame n. exc 1.5 sq. m each & removing to store.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing removing serviceable tiles to store and rubbish of the premises

Taking down cement plaster any description on brick or stone any description complete all as specified& directed by Engr-in-Charge.

Taking up or down 15mm steel tubing and connections, complete all as specified& directed by Engr-in-Charge.

Taking up or down 20mm steel tubing and connections, complete all as specified & directed by Engr-in-Charge.

Dismantling/demolition water tanks of capacity exc 250ltr but not exc 500ltr and removing from site complete all as specified & directed by Engr-in-Charge.

Dismantling of 110mm bore PVC(SWR) drain pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for

Dismantling of 75mm bore PVC(SWR) drain pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed.

M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6 complete all as specified and directed.

M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan to any radius in half brick thick wall, built in cement mortar 1:4 complete all as specified and directed.

M&L Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing.

S&F factory made solid PVC Moulded door shutter 28 to 30mm thick (Stiles) with 2,4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on front face & 2 mm plain colour PVC sheet on back face, supplying and fixing in frame at site as per specification and directed.

S&F 35mm thick IInd class hard wood factory made panelled door shutter(two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. the size of rail and stiles as per IS: 1003 (part-I), kiln seasoned and chemically pressure treated and fixed to chowkats complete all as specified& directed by Engr-in-Charge.

S&F 35 mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (a); supplied and fitted to chowkats complete all as specified& directed by Engr-in-Charge.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1.18mm and fixed tinned tacks or GI wire stampe or nails and screws fixed in repair.

S&F Sheet glass, ordinary quality, in squares n exc 0.5 sq. m each pane3mm in thickness complete all as specified& directed by Engr-in-Charge.

M&L for preparation of new wooden surfaces over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified& directed by Engr-in-Charge.

S&F Butt hinges 100mm long medium weight, stainless steel complete all as specified& directed by Engr-in-Charge.

S&F 150mm 'D' type stainless steel handles complete all as specified & directed by Engr-in-Charge.

S&F 150mm stainless steel , barrel tower bolts of extruded section and fixed complete all as specified & directed by Engr-in-Charge.

S&F 300mm stainless steel , sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified & directed by Engr-in-Charge.

S&F 150mm Floor door stopper of stainless steel alloy body and tongue, with hard drawn steel spring. Fixed in floor complete all as specified and directed

S&F steel ventilator with top hung shutter including hinges steel peg stay etc complete including taking down.

M&L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings, cooler stands (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete & making good the floor in PCC 1:2:4 type B-0 to match the existing floor.

M&L for flat iron as in hold fast, hooks, cleats welded to angle iron door/window frames etc complete all as specified and directed

S&F Steel windows box type with side hung shutters including projecting type hinges with steel handle 150mm, and steel peg stay, complete with glazing bars, dovetailed or welded & factory made (XW2)M/F) double shutter, openable shutter with glazing bars and other openable shutter without glazing bars, fabricated with members of standard size as shown on drawings including frames complete all as specified. Note :- The quoted rates shall be deemed of lugs and FI required for fixing wire cloth, Sheet Glass, Grills, iron mongry and guard bars as shown on drg.

Cutting holes in brick/stone walls n. exc. Half brick built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required all as specified and directed

S & F mild steel cupboard shutter with frame, Godrej pattern made out of 22 guage mild steel sheet including chromium plated MS handle with proper locking arrangement (brass mortice lock vertical type size 65mm 4 lever with escutcheon plates & two keys) with & including two coats of spray painting with synthetic enamel paint of approved tint over a coat of red oxide primer including fixing with 6 Nos 12 mm dia bolt 150mm long grouted in brick wall/concrete including making good the disturbed surface as original complete all as specified and as directed. Note :- The measurement shall be taken of front elevation and not girthwise.

S&F in repairs stainless steel rod of 20 mm inner dia (in lengths as directed) including decorative finial at both ends and pair of stainless steel brackets fixed at both ends with rawl plug & steel screws on walls/beam, all as specified & as directed.

M&L for PCC (1:2:4) type B-0 (using 12.50mm graded stone aggregate), 25mm thick, as in floor and roof paddingcomplete all as specified & directed by Engr-in-Charge.

M&L for light shade joint free Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed of cement mortar 1:6 Make - Kajaria, AGL, Johnson

M & L for light shade Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or colouredmatch over 15mm thick screed bed in CM 1:6 complete all as specified & directed by Engr-In-Charge. Make - Kajaria, AGL, Johnson

M&L Vetrified Ceramic tiles 10mm thick light shade (square/rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in vertical surfaces as dado/ skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over incl 10 mm thick cement rendering in CM 1:4. Make - Kajaria, AGL, Johnson

M&L 75 mm thick PCC(1:3:6) type C2 (using 40 mm graded stone aggregate ) as in plinth protection finished fair and even complete all as specified& directed by Engr-in-Charge.

M&L Glazed ceramic coloured tiles in vertical surface 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles and over 10 mm thick rendring in cm 1:4 complete all as specified & directed by Engr-in-Charge.

M&L for Granite slab 18-20mm thick approved shade as in cooking platform, window cill and the likes, machine cut , bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone including cutting and polishing types and over screed bed 20 mm thick CM 1:6 cement concrete complete

M&L 16-18mm thick green marble (table rubbed and polished) , skirting jambs, pillars, window cills, cooking platform, staircase treads and the likes; laid over with and including 10 mm thick rendering in CM (1:4) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified & directed.

Demolition of Roofs, floors (other than ground floors), beams staircases, landing, chajjas, & similar suspended work Cement concrete (reinforced) complete all as specified and directed.

M&L RCC (nominal mix) type B1 (1:2:4) using 20 mm graded aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, blaconies, canopies, deck slabs and in shelves and the like

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M&L Rendring 10mm thick in CM 1:6 on brick work or concrete surfaces fair faces of brick work & surfaces finished even and smooth without using extra cement all as specified.

M&L for rendering 15mm thick in CM 1:4 on brick or concrete wall surfaces fair faces of brick work & surfaces finished even and smooth without using extra cement with water proof compound ( water proof compound paid seperatly) all as specified.

Supply only Integral waterproofing compound

M&L rendering 5mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified.

Material and labour for prepration over new surface and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as er IS 15489-2004 alkarili and fungal resistance, dirt resistance exterior paint emulsion of required shade (Company Depot tinted) with silicon addtitives @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 0.90 ltr/10 sqm

M&L for providing and applying minimum 1mm thick wall care putty over prepared surface to achieve the surface even and smooth for painting complete all as specified and as directed

Material and labour for complete removal of existing treatment from stone wall /plastered wall and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as er IS 15489-2004 alkarili and fungal resistance, dirt resistance, exterior emulsion paint of required shade (Company Depot tinted) with silicon addtitives @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 0.90 ltr/10 sqm over 1mm thick wall care putty over prepared surface to achieve the surface even and smooth for painting complete all as specified and as directed

M&L for preparing newly plastered surfaces and applying two coats of Oil bound distemper on walls including 2mm thick wall putty complete all as specified and directed by Engineer-in-Charge.

M & L for complete removing of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salt, trading oil greasy spots etc on old decorated surfaces of wall and applying two coats of oil bound distemper of approved shade/tint and inclucluding 1 mm thick Birla white wall care putty. complete all as specified and as directed.

M & L for brooming down old decorated surfaces of walls, plastered or unplastered including cornices, plasters etc and applying one coats of white wash complete all as specified and as directed by Engr- in - Charge.

All as per description of serial item No.56.00 here-in-above but on ceiling surfaces

M&L for preparation of new plastered surfaces of walls and applying three coats of white wash complete all as specified.

Material and labour preparation of newly plastered/unplastered surfaces of ceilings & applying three coats of white wash complete all as specified.

S&F steel tubing medium grade 15mm bore with all fittings fixed complete to wall and or laid in floor complete all as specified & directed by Engr-in-Charge.

S&F 20mm GI tubing Medium grade fix to wall/floor complete all as specified & directed by Engr-in-Charge.

S&F in repair PVC connection pipe, 15mm dia & 600mm long with adopter and washer at both end complete all as specified & directed by Engr-in-Charge.

S&F Rotational moulded polyethylene water storage tanks of 500 Ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified & directed by Engr-in-Charge.

S&F ball valves brass high pressure with polythelene float and fly net complete, screwed , iron pipes 15 mm dia complete all as specified & directed by Engr-in-Charge

S&F in repair fancy type bib taps, chromium plated alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule and fixed bore in dia 15mm complete all as specified & directed by Engr-in-Charge.

S&F in repair white vitreous china wash hand basin 'Flat back' of size 450x300mm fixed on and including new brackets CP waste coupling complete all as directed by the Engr-in-charge.

S&F in repair concealed stop wall /angle valves,fancy type, chromium plated alloy screwed down high presure, screwed both ends for iron pipe or for unions of 15 mm dia complete all as specified & directed by Engr-in-Charge.

S&F 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and directed

S&F PVC waste pipe of 32mm bore of suitable length for WHB/Urinal/sink complete all as specified and directed

S&F Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed

S&F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 485mm x 420mm bowl size 410mm x 3330mm x 160mm complete all as specified and directed

S&F in repairs, vitreous China squatting pan, 'Orissa' pattern, size 580 x 440 mm, white with integral foot rest and 'P' or 'S' trap, including provision of Cement concrete bedding, connection to trap and including flushing pipe etc complete including making good to disturbed surfaces of floor to match with existing surface all as specified and directed.

S&F in repairs PVC low level flushing cistern 10 litrs capacity (white ISI marked) with inlet ball valve, float and handle, syphonic action type including brackets and flush pipe of polythelene of low or high density of PVC 32mm dia for LLFC make Dolfine/Commander Champion, fixed in repairs, complete all as specified.

S&F 15mm dia CP pillar tap fancy type cast copper alloy, CP with capstan head, screwed down high pressure, with or without lettered 'HOT' or 'COLD' with long screwed shank and fly nuts screwed for iron pipe and fixed complete all as directed by the Engr-in-charge.

S&F in repair brass chromium plated shower rose 125mm size with swivel joint type including fixing to steel pipe of 15mm bore or union complete all as specified.

S&F in repair Tubular towel rail, 20mm dia, D type, 60cm long between flanges of Brass chromium plated complete all as directed by the Engr-in-charge.

S&F for Stainless steel plate rack 1mm thick of size 900mm x 900mm x 250mm including fixed with rawl plug and screws on walls complete all as specified and directed by Engr-in-Charge. Make : Nirali

S&F PVC (SWR) pipes 110 mm bore single socketed in any length with rubber ring joints fixed to walls/floor complete all as specified & directed by Engr-in-Charge.

S&F PVC (SWR) bends any radius 110 mm bore complete all as specified & directed by Engr-in-Charge.

S&F PVC (SWR) vent cowl 110mm complete all as specified & directed by Engr-in-Charge.

S&F PVC (SWR),110mm junction single, (Single T) equal or unequal complete all as specified & directed by Engr-in-Charge.

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors/walls complete all as specified & directed.

S&F PVC (SWR) bends 75mm dia any radius complete all as directed.

S&F PVC (SWR) junction single(Single T) equal or unequal 75mm dia complete all as directed.

S&F in repair Grating doom 100 mm dia of chromium plated (Minimum weight 25 gms) fixed with cement complete all as specified & directed by Engr-in-Charge.

S&F 75mm dia PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified & directed by Engr-in-Charge.

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified & directed by Engr-in-Charge.

Demolition Mud in roofs, any thicknes, including plastering , existing tretement and cleaning (whether full thickness removed or only or part there of) etc in all respect and preparing it for further treatment and taking out and disposal of debris & rubbish to a distance exc 1 Km but not exc 1.5 Km complete all as specified & directed by Engr-in-Charge.

M&L screed laid 15mm thick in CM 1:4 with water proofing compound over green concrete surface(WPC will be measured and paid seperately) surface finished even and smooth (without using extra lime or cement) complete all as specified& directed by Engr-in-Charge.

M&L Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq. m including cleaning surfaces over bituminious primer complete all as specified& directed by Engr-in-Charge.

M&L APP based plymeric membrane minimum weighing 3 Kg/Sqm and minimum 3 mm thick reinforced with polyster non woven reinforcement/mat (center core) with thermal insulation laid by toarch application method with overlaps 100mm on length side and 100mm on the width side as per manufacture,s instructions with fabric (wt not less than 150 gms/sqm) on primed surface including two coat of refelective silver aluminium paint over APP membrane complete all as specified.

M&L 75 mm thick PCC(1:4:8) type D2 (using 40mm graded stone aggregate ) as in sub base complete all as specified& directed by Engr-in-Charge.

M&L for 25mm thick Sand cushioning under floors complete all as specified and directed

M&L 60mm thick machine pressed precast conctete interlocking rubberized paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 , M-35 Grade complete all as specified and as directed by Engr-in-Charge.

M&L PCC 1:4:8 type D2 (Using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified& directed by Engr-in-Charge.

M&L Plain cement concrete 1:3:6 type C-1 (using 20 mm graded stone aggregate) set in cement mortar 1:4 as in kerb blocks with plain fair faces including chamfered weathering throating etc complete all as specified& directed by Engr-in-Charge.

M & L for preparation of kerb stone, new un-treated concrete or plastered surfaces of any description over 10cm girth or width, not otherwise described and applying two coats of synthetic enamel paint in black and white colour over a coat of primer complete all as specified and directed.

M&L Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; cooler stand framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 or E-165

M&L for Rough cast plaster on exterior walls applying the under coat of cement and sand mortar 1:3 not less than 10mm thick and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (size between 6 to 12mm) mixed with coarse sand and cement in the ratio of 1:1:1 shall be applied and finished even .The mix of cement and sand shall made slightly wetter than normal for rendering to ensure that larger aggregate are thoroughly covered complete all as specified and directed by Engineer in Charge.

S & F for Pipe Supporting Clamping - Single Pipe of dia 4" (110 mm) down take pipe fixing done with Clamping System consists of Profile Bracket + Continuous Slotted C Channel + U Bolt R/M System running vertically with wall distance 3": Pipe Support Clamping made of 1. Profile Bracket having Wall Distance 3" made of Low Carbon Hot Roll Gauge Corrected (HRGC) Steel (IS 1079 DD); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. 2. Continuous Slotted "C" Channel with ribs to be used of size 10" made of Low Carbon Hot Roll Gauge Corrected (HRGC) steel (IS 1079 DD) are Hot Dip Galvanzied + Zn Al Flake coated with material thickness of 3mm. 3. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 DD used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit : 1. Profile Bracket Wall distance 3" - 2 Nos. 2. Continuous Slotted C Channel of Size 10" - 1 No.; 3. U Bolt R/M for 4" (110 mm) CI or PVC Pipe Dia. - 1 No.; and 4. Justi Khilla 2 1/2" Zn coated - 4 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in the Technical Drawing No. : CE Jaipur Zone - Jaipur; TD/2022/102. Make: Shaivi or equivalent as approved by GE.

S & F for Pipe Supporting Clamping - Single Pipe of dia 3" (75 mm) down take pipe fixing done with Clamping System consists of Profile Bracket + Continuous Slotted C Channel + U Bolt R/M System running vertically with wall distance 3": Pipe Support Clamping made of 1. Profile Bracket having Wall Distance 3" made of Low Carbon Hot Roll Gauge Corrected (HRGC) Steel (IS 1079 DD); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. 2. Continuous Slotted "C" Channel with ribs to be used of size 10" made of Low Carbon Hot Roll Gauge Corrected (HRGC) steel (IS 1079 DD) are Hot Dip Galvanzied + Zn Al Flake coated with material thickness of 3mm. 3. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 DD used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit : 1. Profile Bracket Wall distance 3" - 2 Nos. 2. Continuous Slotted C Channel of Size 10" - 1 No.; 3. U Bolt R/M for 3" (75 mm) CI or PVC Pipe Dia. - 1 No.; and 4. Justi Khilla 2 1/2" Zn coated - 4 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in the Technical Drawing No. : CE Jaipur Zone - Jaipur; TD/2022/102. Make: Shaivi or equivalent as approved by GE.

S & F for Pipe Supporting Clamping - Single Pipe of dia 3/4" (20 mm) down take pipeline fixing done with Clamping System consists of Mono Bracket + U Bolt R/M system running vertically with wall distance 3": Pipe Support Clamping made of 1. Mono Bracket for 3/4" (20 mm) pipe having Wall Distance 3" made of Low Carbon Hot Roll Gauge Corrected (HRGC) Steel (IS 1079 DD); material size 48 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs. 2. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 DD used as per MTC confirms to EN 10204 3.1. Material GradQty. for one unit: 1. Mono Bracket for 3/4" pipe, Wall distance 3" - 1 Nos. 2. U Bolt R/M for 3/4" (20 mm) GI / UPVC/ CPVC pipe Dia. - 1 nos and 3. Justi Khilla 2 1/2" - 2 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in the Technical Drawing no. : CE Jaipur Zone - Jaipur; TD/2022/102. Make : Shaivi or equivalent as approved by GE.

Treatment for sunken portion is as follows:- M&L for water proofing treatment in sunken floors as described hereunder:- 1) Demolition of lean concrete and other type of filling in sunken portion & cleaned the sunken portion incl vertical wall surface complete as directed. 2) PCC (1:2:4) type B0, covered filling in sunken portion 75mm thickness shall be provided at the junctions of RCC slab and adjoining walls. 3) Sunken floor and sides upto finished floor level shall be plastered with 15mm thick plaster in CM 1:4 wixed with WPC@ 3% by weight of cement. 4) Applying bitumen primer of sunken floor & side surfaces TANKMASTIC of M/s STP Ltd @ 0.40 ltr/Sqm. 5) Sunken portion shall be filled with lean concrete (1:5:10), Type E-2 using 40mm aggregate after carring out of satisfactory testing of CIpipes/Joints & Slab/walls by filling water 72 hrs. The sunken portion of Nahani trap/floor trap and pipes, joints shall be emmbeded in PCC (1:3:6) blocks 6) GI Spout pipe 32mm dia and 450mm long cross cutted ends shall be inserted at the time of repair to Sunken portion as directed. Note:- i) In case any defect is noticed the portion shall be grouted with cement slurry mixed with suitable chemical & tested again. This process of grouting and testing shall be repeated till leakage/seapage/dampness is elimaneted ii) Horizontal flat area only measured. iii) Above aspets are deemed to be included in quoted rate.

Excavating in post holes (or similar) each n. exc 0.5 cum getting out returning filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25 cm as in soft/loose soil complete all as specified and directed

M & L for Cement Concrete type C 2 1:3:6 using 40 MM graded stone aggregate as in foundation filling and mass concrete in fixing of fencing post including necessary form work if required at site complete all as specified and directed.

S & F for fencing post/Hand rails, half round or other stock section including embeding in concrete and screwing etc. wind ties for roof including securing bolt posts and struts in fencing including cutting tops to shape as directed, drilling holes,notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc.,and similar work conforming to Fe-290 Gde E-165 including dismantling of existing/old fencing post.

S&F mild steel screw bolts (Machine made) with hexagonal or square heads at one end and the screwed the other to be fitted with washers and one hexagonal or square but exc 5 cm but n.exc 10 cm long, dia of shank 5 to 10mm.

Supply only Chain link MS galvanisd fencing, any size or type complete all as specified and approved by GE.

Fixing only Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc.including provission of binding wire complete all specified and directed.

M&L for mild steel round bars of 10 mm dia and over conforming to Grade E-165 (Fe 290) as in handles of man hole covers & similar works including necessary cutting etc and fixing in position complete all as specified & directed.

M & L for treating ends of posts, backs of chowkhats, etc., area tarred exc. 0.1 Sqm but n.exc 0.5 Sqm each complete all as specified and directed.

M&L for preparing new steel surfaces of any description width or girth exc 10 cm applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer all as specified.

All as per item No 113.00 above but n.exc 10 cm width or girth

S & F factory made kitchen cabinet of size 1.5m x 0.60m x 0.30m made out of 18mm thick PVC celuka sheet having density not less than 650kg/cum one side decorative lamination & other side balancing lamination sheet consisiting of carcase 18mm thick PVC sheet incl shutters made out of 18mm thick PVC board all required brackets 5.5 screwes etc. The panels shall be fabricated using adhesive and screws where every required. All edge shall be covered with 2mm thick edge bonding tape or 90 degree edge bent finish as per make and specification mentioned as per drawing and specification approved by Engineer in charge. Note : (i) PVC celuka sheet manufactured by ISO 9001-2015 certified company, termite proof, water prrof & flame retradat PVC Sheet. (ii) PVC caninet of required size fabricated by joining four 18mm thick PVC celuka ply fixed with each other using solvent cement adhesive and screws and 18mm thick PVC sheet as backing of cabinet screw and solvent cement adhesive etc (iii) The cabinet box will be devided into two ewual part with two leaf shutter and one shelf will be placed in caninate (iv) Caniate will be fixed in wall with 4 x fastners etc and necessary fixing lugs (v) Each shutter will be provided with SS handle of 75mm, CP Piano hinges, magnet/catcher (vi) The quouted rates are incl the ratwes of all fifftings and fixture and ismantling and taking down old kitchen cabinet of any type complete all as specifed

Supplying and fixing in repair factory made PVC shutter of 18 mm thickness consisting of panel of 18 mm thick celluca ply of density 600 Kg.cbm density with prelaminated sheet on one side cut in desired size of shutter and fixed with frame as in cabinet boxes with shelf and shutter full size fitted above the kitchen cooking platform and/or other platform including all necessary fittings and fixtures like nickle plated clip hinges, knobs, channels etc including dismantling boarding, any description, fixed in any position with nails complete all as specified and directed. Note : Items like cupboard knobs, stainless steel channel, CP plate clip hinges are included in the mentioned rates and as per manufacturesrs specification and drawing.The measured area shall be front elevation.

Taking down carefully copper/Aluminium point wiring for light/fan/socket/light fitting/power point and taking down of teak wood batten / PVC casing caping/PVC conduit/steel conduit and making good disturbed surfaces of walls/ceilings /floors etc incl dismentling of fittings.

M&L for point wiring complete with 1.5 Sqmm single core multistranded copper conductor fire resistant low smoke and halogen (FRLSH) PVC insulated and unsheathed cable 1100 Volts grade confirming to IS-694 drawn through non metallic rigid PVC heavy duty conduit in concealed (min 20 mm external dia) but shall be increased as per actual site requirement in accordance with clause No. 19.125 of SSR Part-I ISI marked with wall thickness not less than 1.8 mm including conduit accessories like bends, tees, junction boxes etc fixed concealed/recessed in wall or ceiling including 1.5 mm FRLSH PVC insulated unsheathed copper earth wire including sunken type pressed steel terminal boxes electro plated of suitable size with bakellite white/coloured top sheet cover 3.0 mm thick for one light point controlled by one way switch including cutting chasis in stone/brick wall as required on site all as specified & directed.

All as per item No 116.00 here-in-before but for one fan point controlled by one switch and regulator

All as per item No 116.00 here-in-before but for one exhaust fan point/Fresh Air Fan Point controlled by one switch .

All as per serial item No 116.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on same board.

All as per serial item No 116.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on independent board.

All as per item No 116.00 here-in-before but for one bell/buzzer point controlled by one bell push

All as per item No 116.00 here-in-before but for one light point controlled two ,two way switches

All as per serial item No 116.00 here-in-before but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade including 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade as continuous earth wire in green colour.

All as per serial item No 116.00 here-in-before but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 4.0 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade including 4.0 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade as continuous earth wire in green colour.

Supply and fixing switch piano, flush type, single pole, one way, 5/6 Amp, 230 Volts.

S&F switch piano flush type single pole two way 5 Amps 230 Volts .

S&F bell push flush type 5 Amps 240 V complete all as specified & directed.

S&F bell/buzzer AC 230 volts single pole complete all as specified & directed.

Supply and fixing switch piano, flush type, single pole, one way, 15 Amp, 230 Volts.

Supply and fixing socket outlet, 3 pin (with 2 pin outlet also), 5/6 Amp, flush type, 240 Volts.

Supply and fixing socket outlet, 2 in 1, 3 pin, 5 and 15 Amp, flush type, 240 Volts.

Supply and fixing ceiling rose surface bakelite 65mmx50mm with two or three terminal complete all as specified.

Supply and fix LED batten (1.2m) made of CRCA sheet housing with a PC glossy diffisure duly prewired connection having nominal system lumen output of 2000 lumens at a minimum system efficiency of 115 lumen per watt and total power consumption not more than 20 watt including driver. it should have rated system life time of 40000 burning hours at L70 and should have a temperature of 6500 K CRI >80, thd <10 and PF>0.95 complete all as specified and directed make - Crompton Cat Part CIS-305-40-57-SL-DP-NWH, Philips Cat part BN308C LED20S-6500 L120 PSU WH, Havells Cat Part STOUTPLUS600BS20WLED840SPCWH

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 66 protection complete including all as necessary fitting accessories complete all as directed. Make : Philips/Havells/Crompton

Supply and fixing lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified.

Supply and Fixing 20 watt emergency LED inverter bulb B-22 capacity with inbuilt powerful lithium battery backup of atleast 4 hours and having minimum two years warranty. The lighting shall have deep discharge protection, fast charging, offering cool day light for atleast four hours in off hours. Make : - Havells/Philips/Bajaj

Supply and fixing sheet metal enclosures double door type suitable for fixing MCB's, SPN with 200 Amps rated bus bar,8 way, 240 Volts.

S & F MCB 32/40 Amp, single pole & neutral,240 Volt complete all as pecified & directed.

S & F MCB 6-40 Amp, single pole 240 Volt complete all as pecified & directed.

Supply and fixing Vertical sheet metal enclosures double door type , suitable for fixing MCB, TPN with 200 amps rated bus bar , 4 way. 415 Volts with inbuilt MCCB 4 pole 63 Amp,16 KA

Supply, laying, jointing and testing XLPE insulated armoured heavy duty LT under ground electric cable with aluminium stranded conductor 1100 Volt grade cross sectional area 25 sqmm 4 core laid in trenches/ducts, through pipe, under floors or roads/ along poles etc complete all as specified & directed. Note : Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately.

Excavating in trenches not exc 1.5 metre wide and not exc 1.5 metre in depth for foundation or for shafts, walls, manholes, laying of cables, pipes etc not exc 10 Sqm on plan and getting out in soft/loose soil.

Returning, filling in, including spreading, leveling watering and well ramming in layers not exc 25 cm thick in soft/loose soil.

Removal of excavated soil/ material to a distance not exc 50 metre and depositing where directed at a level not exc 1.50 metre above the starting point complete all as specified.

M/L for brick work with FLY ASH BRICKS(As Per IS-13757(1993) burnt clay fly ash building bricks), (OLD SIZE BRICKS) laid dry & flat abutted with each other with gap between adjacent bricks not exc 10 mm over UG cable for protection and complete all as specified & directed.

M&L for dry sand and punning for cushioning to under ground cable all as directed. Note :- For the purpose of payment only punned thickness shall be measured.

S&F sub main wiring on and including passing through PVC conduit in concealed (including cutting chasis in stone/brick wall) 1100 Volts grade with PVC flexible cable copper conductor cable fire resistant low smoke and halogen (FRLSH) unsheathed multistranded single core of size 6 sqmm and continuous earth with PVC flexible cable copper conductor unsheathed multistranded single core of size 6 sqmm of green colour confirming to IS 694/1990 including taking down existing U/S sub main wiring. (Note: Two runs of cable with one run of earth wire and one run of PVC Coundit should measured as one length)

Material and labour for earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4 mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/Test point/panel/equipment and testing on completion including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, charcoal and salt in alternate layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore 3.00 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers, PCC chamber (1:3:6) type C1, 40mm thick precast RCC cover 1:2:4 type B1 shall be provided on CI frame etc complete all as specified & directed. Note : - Quoted rate shall be deemed to include for earth wire with protection pipe up to 7.5 meter length.

Disconnecting form elect connection and taking down carefully the existing electric energy meter of any capacity, any make,any size and depositing same the electric energy meter in AGE E/M store yard all as specified and directed by the Engineer-in-Charge.Refixing the same inside the Old Meter inside Box carefully incl necessary electric connections complete all as directed.

Disconnecting form elect connection and taking down carefully the existing Ceiling fan/Exhaust fan/Geyser of any capacity, any make,any size and depositing same the Ceiling fan/Exhaust fan/Geyser in AGE E/M store yard all as specified and directed by the Engineer-in-Charge.Refixing the same Ceiling fan/Exhaust fan/Geyser carefully incl necessary electric connections complete all as directed.

M/L for GI pipe ( Light grade ) for protection of LT cable fixed to walls/ poles/road crossing including clamps complete of 40 mm bore

Supply and fix ceiling fan complete with electronic type regulator , copper winding and accessories 230v 1200mm sweep BEE 5 star rated with brushless direct current motor (BLDC) including taking down old unserviceable ceiling fan complete all as specified and directed by engineer-in-charge.

S&F in repair cubical metallic box of size 1.00m x 0.90m x 0.30m depth made out of 2mm thick mild steel sheet, front openable, double door with locking arrangement with & including 3mm thick plain sheet clear glass of suitable size fixed to facilitate meter reading, all internal & external steel surfaces painted with two coats of synthetic enamel paint over a coat of red oxide primer, internal wiring with PVC insulated single core multistranded copper conductor FRLS cables IS-694 marked of adequate size but not less than 6 sqmm with proper ferrule & cable gland, box shall be fixed on wall with ‘Anchor’ type /fastener type bolts & nuts (Set of 6 bolts of 12mm dia 200mm long with nuts & washers) grouted into the wall properly to hold the box, writing MES No/Qtr No for each energy meter with thick white synthetic enamel paint, Neoprene rubber gasket shall be provided for proper sealing, box shall have arrangement for fixing electric energy meters – 04 Nos, MCB DB TPN 4 way -01 No complete all as directed.

Supply and fixing in repair of 25 mm bore GI water tubing IS-1239 marked, medium grade, in replacement including all necessary pipe fittings laid in trenches, on wall, under floor, under road on same or new route and making good the disturbed portion as existing and including taking down of old unserviciable pipe of the following sizes :- Note :-excavation earth work will be measured and paid saperatly.

All as per ser item No 154.00 but 20 mm bore

supply and fix exhaust fan metal body AC single phase 230/240 V of size 300 mm sweep with louver including making suitable opening/hole in wall all as specified and directed by ebgineer-in-charge

Supply and fix Fresh air fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 MM complete all as specified and directed by Engr-in-Charge

ARUN ENTERPRISES (BID ID -3331470)

M/S JINDAL ENTERPRISES (BID ID -3340079)

M/s Laxmi Enterprises (BID ID -3339265)

Radha Enterprises (BID ID -3331120)

shiva construction (BID ID -3339141)