Construction of Permanent Building of Type-IV, Type-III and Type-II Residences for Officers-Employees in Ken-Betwa Link Canal Colony Campus, Nawab Tank, Banda under Ken-Betwa Link Project.

Amount

Boring with hydraulic piling rigs with power units. providing and installing cast in situ single under reamed piles(300mm dia ) of specified diameter and length below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) : 300 mm dia piles

Making Bulb of dia. 750 mm. in under reamed piles, Constructing With M-25 Grade.

Excavation in foundations in ordinary soil including lift upto 1.5 m and lead upto 30 mt.& including filling, watering and ramming of excavated earth into the trenches or into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the Engineer-Incharges upto a distance of 30mt. from the foundation trenches.

Excavating, supplying, stacking and filling of local earth by mechanical transport upto a lead of 3km also including ramming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift.

Local Sand filling in plinth including supply of necessary quantity of sand from a local quarry. from the site of work and including watering, dressing etc rate to include cost of all materials labour T & P etc required for proper completion of work.

Providing and laying cement concrete 1:4:8 (1 cement :4 coarse sand :8 graded Stone aggregate 40 mm nominal size) including supply of all materials, labour T&P etc, required for proper completion of the work and curing complete As per direction of E/C.

Treatment of soil under existing floors using chemical emulsion , 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

R.C.C. (M-25) work with cement, coarse sand and 20 mm. guage approved stone grit as per in the proportion of Mix Design in PILE CAP ( excluding supply of reinforcement and its fixing and binding the same with 24 B.W.G.G.I. binding wire and excluding necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works. Up to plinth level.

R.C.C. (M-25) work with cement , coarse sand and 20 mm. guage approved stone grit as per proportion of Mix design excluding supply of reinforcement and its fixing and binding the same with 24 B.W.G.G.I. binding wire and excluding necessary centering and shuttering etc and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works.

M-150 brick work in 1:4 mortar in Sub Structure including supply of all materials labour, tools and plants etc. required for proper completion of the work.

M-150 brick work in 1:4 mortar in Super Structure including supply of all materials labour, tools and plants etc. required for proper completion of the work.

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (BRICK COBA )

Providing and laying damp - proof course 40 mm thick with cement concrete 1 : 2 : 4 ( 1 cement 2 coarse sand 4 graded stone aggregate ) including cost of all labour,material and T&P.

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Supply & fixing of flush door Shutter commercial quality conforming to I.S. 2202 Part-I (1983) including fixing of wooden cleats and stoppers and including fixing and adjustmant of hinges, bolts,handles & springs fitting with necessary screws complete. for Providing and fixing flush doors with decorative veneering ISI marked flush door shutters conforming to IS: 2202 (Part I), (Both Side Laminated.) 35mm thick.Single Leaf

Mild steel or Iron work of small sizes and sections such as holding down bolts, hold fast tierods, gratings, railings,brackets, gates etc. ( when not included in an over all rates) wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding, grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing.

Door / windows & Staircase grill.

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 + 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 X 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Providing and Fixing factory made PVC door frame made of PVC extruded sections of size 75 mm x 53 mm , having wall thickness 2.0 mm ( ± 0.2 mm ) . Both verticalssides of the frame reinforced with PVC profile of cross section size 28 mm x 30 mm x 2 mm thickness ( ± 0.2 mm ) and 75 mm x 200 mm long , including reinforcing both ends of the top frame with PVC profile . PVC Door Frame and PVC reinforcement profile to be mitred cut , jointed and fusion welded together , including providing and fixing 3 nos of 125 mm long stainless steel hinges to frame , fixing the frame with jamb with required nos & sizes of anchor dash fastener , all complete as per manufacturer's specification and direction of engineer in - charge.

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and cLerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick :Float glass panes 5.5 mm thick glass panes.

Providing and fixing anodised aluminium grill ( anodised ) transparent or dyed to required shade according to IS : 1868 with minimum anodic coating of grade AC 15 of approved design / pattern, with approved standard section and fixed to the existing window frame with C.P. brass / stainless steel screws @ 200 mm centre to centre , including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening , all complete as per requirement and direction of Engineer - in- charge .

Providing and fixing factory made 30 mm thick door shutter made of solid PVC foam profile with homogeneous fine cellular structure having smooth outer integral skin having 71 mm width & 28 mm thick as vertical & horizontal styles. joints are made using solvent adhesive and GI 'C' sections (39mm X 19mm X 0.6mm thick) or M.S. pipe (40mm x 20mm) stiffener frame insert and telescopic polymeric 'L' corners. The panel shall be filled with 3mm thick high pressure compact laminate as per manufactures specifications and direction of the Engineer-in-charge, cover molding shall be provided for covering fixing screws and elegant look. (for W.C. & bath Room shutters.)

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of1.4 mm in both directions with wire of dia 0.63 mm , for doors , windows and clerestory windows with hinges and necessary screws : 35 mm thick shutters . With ISI marked stainless steel butt hinges of required size.Second class teak wood(Door&window)

Reinforcement with Fe-500 in RCC work including cutting,bending,placing and binding proper completion of the work and including supply of steel and and over lapping & hooks.

15 mm plinth plaster 1:4 cement sand mortar.

12 mm cement plaster in 1:6 cement sand mortar on brick work surface including cost of all labour,material,T&P etc .

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Providing and laying 8 to 10 mm thick ivory or light shade vitrified tiles of 600 X 600 mm size in flooring or skirting laid with cement mortar 1:3 (1 cement : 3 coarse sand) finished with cement slurry & with pigment grouting & polishing complete including supply of all materials, labour, T & P etc. required for proper completion the work .

Supply & fixing 6 mm thick china white glazed tiles in flooring or in skirting or dado laid with 1 : 4 cement and approved coarse sand mortar finished with white cement slurry jointing and polishing complete including supply of all materials labours & tools etc, required for completion of the work. (size of tiles upto 300x 300 mm).

Painting two coat over priming coat (but including cost of priming coat) on steel and other metal surfaces up to 10 cm. width or girth or small articles not exceeding 0.10sqm in area white superior synthetic enamel specified brushing to give an even shade and including cleaning the surface of all dirt, dust and other foreign matter sand papering and stoping including cost of all materials, labour tools and plants etc. required for proper completion of the work.

Finishing walls with Premium Acrylic Smooth Exterior paint with Silicone additives of required shade New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2 20 kg/ 10 sqm)

Distempering (Two coat) with oil bound distemper of approved brand and manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer of after thoroughly brushing the surface free from mortar droppings & other foreign matters & also including preparing the surface even with plaster of paris or approved synthetic material & sand papered smooth including cost of all materials.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand & manufacturer, over the plastered wall surface to prepare the surface even & smooth complete.

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Providing and fixing Stainless Steel sliding door bolts ISI marked to required colour or shade with nuts and screws etc. complete : 250x16 mm .

Providing and fixing stainless steel tower bolts with necessary screws etc. complete

(a) 250 mm X 10mm

(a) 200 mm X 10mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :For Door &Window

Providing stainless steel tower bolt with 10 mm dia and screw. ( i ) 100 mm long.For Window

Providing & laying of light cinder filling under floor of toilets & other sunken roofs.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound Including cost of all .

Providing M.S. foot rest including fixing with 20x20x10 cm. cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 gradded aggregate of nominal size 20mm ) as per standard design with 20x20mm sq bars.

Providing and fixing C.I. tee at the inlet and outlet of septic tank

Providing & fixing 75mm dia vent pipes.

Providing & fixing of 75mm dia cast iron terminal guard

Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality of HD-20- Circular shape 560mm internal diameter.

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks of class designation 75 and S.W. drain pipe of 100 mm diameter, 1.8m long complete as per standard design.

Providing and fixing 18 mm thick Granit stone with gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc complete.

Centering & Shuttering i/c strutting, propping etc and removal from for all heights.

Foundation, Footing, base of column etc. i/c Cost of all Labour , Material, T&P Complete as per E/C.

Column , piller, piers, Abutments posts,Struts, Boundry Wall, Saptic tank etc. i/c Cost of all Labour , Material, T&P Complete as per E/C.

Providing and laying of coping work for boundry wall cement concrete, excluding the cost of centring and shuttering by 1:2:4 mortar.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank,IS:12701 Marked,with cover and suitable locking arrangement and making necessary holes for inlet,outlet and overflow pipes but without fittings and base support for tank of Capacity 1000 ltr.

Providing & fixing White vitreous china water closet squatting pan ( Indian type ) Long pattern W.C Pan of size 580x440 mm, along with " S " or " P " trap including " S " or " P " trap at site complete with all operations including all necessary materials , labour and disposal of dismantled material i / c malba , all complete as per the direction of Engineer - in charge .

Providing and fixing white vitreous china pedestal type water closet ( European type W.C. pan ) with seat and lid , 10 litre low level white P.V.C. flushing cistern , including flush pipe , with manually controlled device ( handle lever ) , conforming to IS : 7231 , with ail fittings and fixtures complete , including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing 8 mm dia C.P./S.S . Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer in charge .

Providing and fixing wash basin White Vitreous China of size 630x450 mm with ja single 15 mm C.P. brass pillar tapwith C.I. brackets , 15 mm C.P. brass pillar taps , 32 Imm C.P. brass waste of standard pattern , including painting of fittings and brackets , cutting and making good the walls wherever require :

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931 including angle valve for WC flushing cistern , jet & kitchen sink of 15 mm nominal bore.

Providing and fixing uplasticised PVC connection pipe with brass unions of 15 mm nominal bore.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS : 8931 of 15mm nominal bore.

Providing and fixing Stainless Steel A ISI 304 ( 18/8 ) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm , including painting of fittings and brackets , cutting and making good the walls wherever required of 510x1040 mm bowl depth 250 mm.

Providing & fixing PVC waste pipe for sink including PVC waste fittings Complete Flexible Pipe of 32 mm Dia.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.

15 mm nominal outer dia Pipes

20 mm nominal outer dia Pipes

Providing and fixing Gl pipes complete with Gl fittings and clamps , i / c cutting and making good the walls etc. Internal work - Exposed on Wall of 40 mm nominal bore.

Providing and fixing brass stop cock of approved quality : For Internal Toilet of 20 mm nominal bore.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end ) : For vertical pipe connection with terrace ringmain.

25mm nominal bore

32mm nominal bore

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A , including jointing with seal ring conforming to IS : 5382 , leaving 10 mm gap for thermal expansion , ( i ) Single socketed pipes of 110 mm dia. ( For rain water )

Providing and fixing on wali face unplasticised - PVC moulded fittings / accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A , including jointing with seal ring conforming to IS : 5382 , leaving 10 nm.gap for thermal expansion .

Single Push Fit Coupler(110 mm dia)

Plain bend 87.5 deg(110 mm dia)

Shoe plane(110 mm )

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised PVC rain water pipes by means of 50x50x50 mm hard wood plugs , screwed with M.S. screws of required length , including cutting brick work and fixing in cement mortar 1 : 4 ( 1 cement : 4 coarse sand ) and making good the wall etc. complete of 110 mm dia.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1 : 2 : 4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size ) over P.V.C. sheet 1 m x1 m x 400 micron , finished with 12 mm cement plaster 1 : 3 ( 1 cement : 3 coarse sand ) and a coat of neat cement , rounding the edges and making and finishing the outlet complete .

Providing , fixing , jointing and testing , uPVC SWR pipes , - type B conforming to IS : 13592 to wall , ceiling and floor , approved quality , complete , for soil , waste & rain water drain including pushfit jointing with seal ring . ( i ) Single socketed pipes (Internal Toilet Soil & Waste Pipe of 110 mm.)

Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion .

Bend without door ( 87.5 ° ) of 110mm bend.

Bend without door ( 45 ° ) of 100mm.

Coupler of 110mm.

Vent Cowl of 110mm

Providing , fixing , jointing and testing , of PVC Multi Floor Trap with jali of minimum 50 mm water seal , making necessary cutting in slab or floors and making good of Size110mm x 75mm x 50mm / 40mm ( Toilet ) including supports with cement concrete 1 : 3 : 6 complete as approved by Engineer - in - Charge .

Wiring points for light with 1.5 sqmm.FRLSH PVC insulated single core Copper condutor cable in PVC conduit pipe partly concealed in wall and partly laid in slab along with the reinforcement before concreting , complete with 1.5 sqmm.FRLSH PVC insulated multistrand copper conductor cable as earth continuity wire and modular type switch etc. complete in all respects .

Light point

for two way light Points .

for fan and light duty exhaust fan .

for 5 amp plug point with modular type switch and socket etc.

Supply & wiring of submains with 2 nos . 2.5 sq.mm & with 1 no . earth wire of 1.5 sq.mm FR PVC insulated 1100 V grade single core multistrand copper conductor cable in 20 mm dia heavy duty ( 2mm ) thick ) PVC conduit complete , including supply of all material , labourand T & P etc. required for proper completion of the work as directed by Engineer I / C .

Supply and wiring of submain 2 number 4 sqmm FRLSH PVC insulated 1100 V grade multistranded single core copper conductor cabie in heavy duty ( 2 mm thick ) 20mm dia PVC conduit partly concealed in wall and partly laid in slab along with one number 2.5 sqmm FRLSH PVC insulated multistranded copper conductor cable as earth contunity wire etc. complete in all respects .

Supply and wiring of submain 2 number 6 sqmm FRLSH PVC insulated 1100 V grade multistranded single core copper conductor cable in heavy duty 2 mm thick ) 20mm dia PVC conduit partly concealed in wall and partly laid in slab along with one number 4 sqmm insulated multistranded copper conductor cable as earth contunity wire etc. complete in all respects .

Supply and wiring of submain 2 number 10 sqmm FRLSH PVC insulated 1100 V grade multistranded single core copper conductor ! cable in heavy duty ( 2 mm thick ) 25mm dia PVC conduit partly concealed in wall and partly laid in slab along with one number 10 sqmm insulated multistranded copper conductor cable as earth contunity wire etc. complete in all respects .

Supply and wiring of submain 2 number 16 sqmm . FRLSH PVC insulated 1100 V grade multistranded single core copper conductor cable in heavy duty ( 2 mm thick ) 32mm dia PVC conduit partly concealed in wall and partly laid in slab along with one number 10 sqmm insulated multistranded copper conductor cable as earth contunity wire etc. complete in all respects .

Supply and wiring of submain 4 number 6 sqmm insulated 1100 V grade multistranded single core copper conductor cable in heavy duty ( 2 mm thick ) 32mm dia PVC conduit along with two numbers 4 sqmm insulated multistranded copper conductor cable as earth contunity wire etc. compiete in all respects .

Supply and wiring of submain 4 number 10 sqmm insulated 1100 V grade multistranded single core copper conductor cable in heavy duty ( 2 mm thick ) 32mm dia PVC conduit along with two numbers 6 sqmm FRLSH PVC insulated multistranded copper conductor cable as earth contunity wire etc. complete in all respects .

Supply and wiring of submain 4 number 16 sqmm insulated 1100 V grade multistranded single core copper conductor FRLSH PVC cable in heavy duty ( 2 mm thick ) 40mm dia PVC conduit along with two numbers 10 sqmm FRLSH PVC insulated multistranded copper conductor cable as earth contunity wire etc. complete in all respects .

Supply fixing and concealing of 20mm dia.2mm thick PVC conduit pipe with ISI mark embossed and with PVC acessories confirming to IS No. 3419 for drawing wires duly sealed at joints with original resin / adhesive to make the complete piping rigid , plastering with cement sand mortar finished to level with matching colour including cost of material labour and T & P etc required for proper completion of work .

Erection and testing of ceiling fan and regulator for room height upto 3.5mts . including supply of 3mm thick G.I. Pipe 19mm dia duly painted , cornplete in all respects .

Erection and testing exhaust fan on the exhaust hole with suitable size of rag bolts nuts and washers etc. complete in all respects .

Supply and fixing hexagonal / Round G.P. fan box of approved make made up of 1.0mm thick ISI Marked G.P. sheet spot weeldeed Four to Eight holes of 25.4 mm for pipe entry of the box . Holes should be semi shuttered type with 0.5mm G.P. Sheet made upper & lower cover duly screewed fitted with 300mm round zink coted M.S Bar X 12mm & brand name should be embossed . Fixing with wiring conduit laid in the R.C.C roof before concreting alongwith supply of all material, labour, T&P etc. required for proper completion of the work .

Supply of Ceiling Fan with fan motor of A.C Permanent insulation , capacitor rating conforming BEE 5 star rating and IS : 374/79 and also comply with IS : 1709/1984 with latest amendment . The rated voltage 220/240 volts , 50Hz , 1 - ph AC the fan assemble should consists of down road blades , shackle canopies etc and with double ball bearing system . BEE 5 Star rated - 1200mm sweep

Supply fixing of electronic fan regulator ( Modular ) 120-280 V. ISI marked, on the existing switch board including making connetion, required material , labour T/P etc for proper completion of work to the satisfaction of Engineer in charge of work .

Supply & fixing of LED Tube Light with Metal heavy dutyBox type batten Light fitting 2 x 22 watt suitable for up to 2 x 22 watt LED Polycarbonate tube light complete including tube etc suitable for both surface & surface complete in all respects .

Supply & fixing of LED Tube Light with Metal heavy duty Box type batten Light fitting 1 x 22 watt suitable for up to 1 x 22 watt LED Polycarbonate tube light complete including tube etc suitable for both surface & surface complete in all respects .

Supply & fixing of 2'x 2' 36Watt to 46Watt , Indoor recess / Surface LED Square Fitting for Armstrong Ceiling Powder quoted CRCA hhousing body diffuser of Special Polycarbonate meterial and Driver set Co. Complete in all respects.

Supply & fixing of recess / Surface mounting round 10 to 15 watt , cut out Min 125mm , Height Min 40mm , LED Down Lighter having Powder coated die cast aluminium housing with heat sink , diffuser / Reflector and driver set , suitable for 24Hr continuous Operation , complete in all respect .

Supply & fixing of 1'x 1 ' 18Watt to 20Watt , Indoor recess / Surface LED Square Fitting for Armstrong Ceiling Powder quoted CRCA hhousing body diffuser of Special Polycarbonate meterial and Driver set Co. Complete in all respects .

Suuply and fixing of water tight oblong 10 watt LED bulhead luminaire with driverr set confirming to IP 65 and above Protection complete in all respect .

Supply and fixing of surface / flush mounting distribution boards with additional metal door withot MCB complete in all respects .

8 Way SPN

12 way SPN

4 Way TPN

6 Way TPN

8 Way TPN

Supply and fixing of 6Amp to 32 Amp ( 10 KA ) SP MCB in existing MCB , DB complete with connections as required.

Supply fixing and making connection of following MCBS complete in all respects as per direction and satisfaction of engineer - in - charge .

63 Amp . FP MCB

40 Amp . FP MCB

40 Amp . DP MCB

63 Amp . DP MCB

Supply fixing and making connection of following MCCBS of 100 Amp . FP MCCB ( 25KA ) complete in all respects as per direction and satisfaction of engineer - in- charge .

Supply and fixing of power plug with 15A / 250 V flush type switch and 5 Pin 15 A / 250V flush type universal socket in suitable M.S. box of 175mmx100x50mm size with phenolic laminated bakellite sheet cover 3mm thick fixed with brass machine screws and cup washer .

Supply and fixing of power plug with 20A / 250 V flush type switch and 5 Pin 20 A / 250V flush type universal socket in suitable M.S. box including supply of all material , labour T&P etc. required for proper completion of work ...

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required .

Supply and fixing Single Pole MCBS Blanking Plate complete in all respects .

Suplly and burring of safe Earthing Electrode T - 39 . Cu Copper Coated , Length 2000mm , cuter pipe 76.3mm X 3.2 inner pipe 42.4mm X 2.6mm , terminal Dia 12mm , coating 80-100 micron filled with crystalline conductive mixture ( CCM ) having anti corrosive & conductive property with 50kgs activated soil ( BFC ) capable of reucing the soil resistivity with good mixture of retaining capacity along with 30cm square C.I. frame withhinged cover & mansonry housing . ( From electrode terminal to switch board , cost of 25x3 copper strip will be extra Make).

Supplying & Laying of 25mmx3mm G.I. Strip for earthing purpose as required complete in all respects .

Supply & fixing of two number 8 SWG G.I. wire in 15mm dia GI pipe for earthing purpose as required complete in all respects .

Supply and laying of aluminium conducter , PVC insulated armoured , served , sheeted cable 1000 bolts grade at a depth of 750mm below ground level over a cushion of 75mm thick sand alround and protected with burnt bricks on sides and top on surface , the

35 sqmm 3.5 core

125 sqmm 3.5 core

16 sqmm 4 core

10 sqmm 4 core

6 sqmm 4 core

6 sqmm 3 core

Supply & fixing of brass nickle plated compression gland for PVC insulated & armoured served sheathed , underground cable including rubber ring etc. compiete in all respects . The armouring of the cable shall be properly connected with the earth as per dire

35 sqmm 3.5 core

25 sqmm 3.5 core

16 sqmm 4 core

10 sqmm 4 core

6 sqmm 4 core

4 sqmm 3 core

Supply and fixing of Palm pin type copper tin plated cables sockets ( lugs ) to the cable leads , insuslating with tape and making of connections etc. complete in all respects as per direction of Engineer- Incharge .

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray ( Galvanisation thickness not less than 50 microns ) with perforation not more than 17.5 % , in convenient sections , joined with connectors , suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts , etc. as required .

100 mm wide x 50 mm depth x 1.6 mm thickness .

450 mm width X 50 mm depth X 2.0 mm thickness

Supply and burying of 40mm dia X 4.5 metres long G.I. Pipe vertically for earthing having 12mm dia. Holes spaced 75mm apart drilled up to 2 metre from the bottom complete with earthing lead of No. 6 to 8 SWG GI wire in G.I. Pipe up to appron (and from appron to switch board the cost of G.I. wire and pipe will be extra) upto switch board, 30cm square C.I. box with hinged cover masonary enclosure, funnel at top, alternate layers of charcoal/coke and salt at least 150mm thick alround etc. as per directions of Engineer-in- charge complete in all respects as per drawing.

Suplly and burring of safe Earthing Electrode T-39 Cu Copper Coated, Length 2000mm, outer pipe 76.3mm X 3.2 inner pipe 42.4mm X 2.6mm, terminal Dia 12mm, coating 80-100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50kgs activated soil (BFC) capable of reucing the soil resistivity with good mixture of retaining capacity along with 30cm square C.I. frame withhinged cover & mansonry housing.(From electrode terminal to switch board, cost of 25x3 copper strip will be extra) Make: As approved in U.P.P.W.D & Supply and laying of 32mm X 6mm G.I. strip from earth electrode.

directly in the ground as required complete in all respects.

Supply and Laying of 32mm X 6 mm Copper strip from earth electrode directly in the ground as required complete in all respects.

Supply and laying of 25mm x 3mm G.I. strip from earth electrode directly in the ground as required compiete in all respects.

Supply and fixing of one number 8 SWG G.I wire in 15mm dia. G.I pipe for earthing laid in ground or in wall duly concealed including the cost of cement, sand, labour, T&P other material required for proper completion of the work as directed at site.

Providing and fixing MV danger notice plate of 200 mm X 150 mm made of mild steel at least 2mm thick & vitreous enamelled white on both sides and with inscription in signal red colour on front side as required.

Providing and fixing HT danger notice plate 250 mm x 200 mm made of mild steel at least 2mm thick & vitreous enarnelled white on both sides and with inscription in signal red colour on front side as required.

Supplying and Fixing of Fire buckets, round bottom made of G.I. Sheet 9-11 litres capacity duly painted as per fire brigade design, supported on hanging bracket chained and locked, initially filled with fine river sand, water as per directions of Engineer-in-charge.

Supplying & Laying of 1800 mm x 900 mm x 12 mm thick chequered rubber matting of tested quality.

Supply and fixing danger board fabricated from 10 gauge MS sheet as per IE Rules.

S/F of shock treatment chart (prescribed under I.E.rules) duly framed with glass and supported from back with hard board or soft board with supply of all material labour T & P for proper completion of work.

Providing & fixing in position 1000 mm wide, Electrical Insulating Mats, 2mm thick, suitable upto 1.1 KV grade including cutting to required length complete as required per specifications or upto the satisfaction engineer-in-charge

Supplying and Laying of Rubber mat 1000 mm. Wide to withstand 11 KV dielectric strength as per latest IS 15652-2006 etc. as required.

Supply of Tool & First Aid Box with all necessary tools for maintenance of electrical installation & First aid.

Supply & fixing of 7 mtr GI Octagonal Pole of approved make (top dia 70mm, Bottom dia 130 mm and base plate 12 mm thik) having 3mm thikness with Single arm bracket (1 Mtr length) on RCC foundation including the cost of foundation, foundation bolts, excavation & back filling and Required T&P complete in all respect.

Supply and fixing of LED street light fitting having die cast aluminium body and diffuser with driver set suitable for 45 watt to 50 watt. Confirming to IP 66 and above protection complete in all respect.

Supply and fixing of 6 Amp to 32 Amp DP MCB (10KA) (C curve) for poles.

Supply and fixing of Bakelite sheet 3 mm thick of suitable size & connector.

Supply and fixing of actory wired integral LED flood light luminaires with die cast aluminium housing built with driver set suitable for 40 to 50 watt conforming to IP 65/66 protection complete in all respect (CAT-AAA)

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refiliing the trench but excluding sand cushioning and protective covering etc., complete as required.

90 mm dia (OD-90 mm & ID-76 mm nominal)

120 mm dia (OD-120 mm & ID-103 mm nominal)

160 mm dia (OD-200 mm & ID-175 mm nominal)

200 mm dia (OD-200 mm & ID-175 mm nominal)

Supply and laying of aluminium conducter, PVC insulated armoured, served, sheeted cable 1000 bolts grade at a depth of 750mm below ground level over a cushion of 75mm thick sand alround and protected with burnt bricks on sides and top on surface, the

120 sqmm 2 core

10 sqmm 2 core

6 sqmm 2 core

Supply & fixing of brass nickle plated compression gland for PVC insulated & armoured served sheathed, underground cable of 6.sqmm 4 core including rubber ring etc. complete in all respects. The armouring of the cable shall be properly connected with the earth as per direction engineer incharge.

Supply and fixing of 120 sqmm. Palm/pin type copper tin plated cables sockets (lugs) to the cable leads, insuslating with tape and making of connections etc. complete in all respects as per direction of Engineer Incharge.

Constrution of C.C road inluding Prepration of sub-grade, sub-base, pavment, making for proper complition of work as per Engineer in-charge.

M/S RADHIKA CONSTRUCTION COMPANY (BID ID -5041763)