8125/SAR-T-54/2025-26 PROVN OF AC POINTS AND ALLIED WORKS IN SMQs AND SPECIAL REPAIR TO ELECTRIC WIRING AND ALLIED WORKS AT OFFICERS MESS, L/IN ACCN FOR SNCOs AND AIRMEN AT 1AFSB DEHRADUN UNDER GE (AF) SARSAWA

Amount

S & F MCB distribution board 4 way double door factory made sheet steel, phosphates, powder painted with 200 Amps rated bas bar, 240 volts, neutral link, earth bar and Din rail single door complete including making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

S & F MCB SP 20-25 Amps 10 KA rating, 240 Volts C Curve type complete all as specified and directed.

S & F MCB SPN 40 Amps 10 KA rating, 240 Volts C Curve type complete all as specified and directed.

S & F sub-main wiring with two single core FRLS PVC insulated, unsheathed, multistranded copper conductor cable of size 4 sqmm 1100 volts grade and including non metallic rigid 25 mm dia PVC casing caping with all fitting and fixing accessories and including PVC insulated unsheathed, multistranded copper conductor cable of size 2.5 sqmm for earth continuity conductor and making good the disturbed surface complete all as specified and directed.

S & F sub-main wiring with two single core FRLS PVC insulated, unsheathed, multistranded copper conductor cable of size 6 sqmm 1100 volts grade and including non metallic rigid 25 mm dia PVC casing caping with all fitting and fixing accessories and including PVC insulated unsheathed, multistranded copper conductor cable of size 4 sqmm for earth continuity conductor and making good the disturbed surface complete all as specified and directed.

S & F sheet metal enclosure with socket plug top and MCB single pole and neutral with two pin and earth plug with one SP MCB 25 Amp 240 volt complete all as specified and directed.

Design, manufacture, supplying, installation correct alligned position, making proper connections, testing and commissioning of following LT panels suitable for 415 V, 3 phase, 4 wire, 50Hz power distribution system. The panel shall be indoor IP42 rating, free standing, floor/wall mounting, sheet metal clad, cubicle, dust and vermin proof type compartmentalized design fabricated out of 16 SWG CRCA sheet 2 mm thick complete with aluminium bus bars of 100 Amps separate earth bus bar to provided through out the length of the panel. The incoming and outgoing feeders shall be accommodated in a modular arrangement and shall be interlocked to avoid paralleling adequate size cable alley, interior painting, earthing numbering, danger plate etc as required complete all as specified and directed. Incoming :- (a) MCCB FP 40 Amps with thermomagnetic O/C & SC release 25 KA-01 Each (b) RYB phase indication lamps-set of 3 (c) Multi functiional meters-01 Each (d) Aluminium bus bar 100 A 4 strip with heat shrinkable sleevesa and colour coded. Outgoing :- (a) MCB DP 32 Amps 'C' series-07 Nos Note: There should be a space to accommodate 07 x Prepaid meters incl connections along with lugs/thimbles all as required at site.)

Design, manufacture, supplying, installation correct alligned position, making proper connections, testing and commissioning of following LT panels suitable for 415 V, 3 phase, 4 wire, 50Hz power distribution system. The panel shall be indoor IP42 rating, free standing, floor/wall mounting, sheet metal clad, cubicle, dust and vermin proof type compartmentalized design fabricated out of 16 SWG CRCA sheet 2 mm thick complete with aluminium bus bars of 100 Amps separate earth bus bar to provided through out the length of the panel. The incoming and outgoing feeders shall be accommodated in a modular arrangement and shall be interlocked to avoid paralleling adequate size cable alley, interior painting, earthing numbering, danger plate etc as required complete all as specified and directed. Incoming :- (a) MCCB FP 40 Amps with thermomagnetic O/C & SC release 25 KA-01 Each (b) RYB phase indication lamps-set of 3 (c) Multi functiional meters-01 Each (d) Aluminium bus bar 100 A 4 strip with heat shrinkable sleevesa and colour coded. Outgoing :- (a) MCB DP 32 Amps 'C' series-06 Nos Note : There should be a space to accommodate 06x Prepaid meters incl connections along with lugs/thimbles all as required at site.

Design, manufacture, supplying, installation correct alligned position, making proper connections, testing and commissioning of following LT panels suitable for 415 V, 3 phase, 4 wire, 50Hz power distribution system. The panel shall be indoor IP42 rating, free standing, floor/wall mounting, sheet metal clad, cubicle, dust and vermin proof type compartmentalized design fabricated out of 16 SWG CRCA sheet 2 mm thick complete with aluminium bus bars of 100 Amps separate earth bus bar to provided through out the length of the panel. The incoming and outgoing feeders shall be accommodated in a modular arrangement and shall be interlocked to avoid paralleling adequate size cable alley, interior painting, earthing numbering, danger plate etc as required complete all as specified and directed. Incoming :- (a) MCCB FP 40 Amps with thermomagnetic O/C & SC release 25 KA-01 Each (b) RYB phase indication lamps-set of 3 (c) Multi functiional meters-01 Each (d) Aluminium bus bar 100 A 4 strip with heat shrinkable sleevesa and colour coded. Outgoing :- (a) MCB DP 32 Amps 'C' series-04 Nos Note : There should be a space to accommodate 04x Prepaid meters incl connections along with lugs/thimbles all as required at site.

M &L for earthing complete with galvanized steel earth plate electrode 60cm X 60cm X 6mm thick buried directly vertically in ground to depth not less than 2.25 mtr below ground level, with top edge of earth plate not less than 1.5 mtr below ground level surrounded from all sides by 15 cm thick packed layer of Charcoal dust & common salt filled in alternate layers and electrode connected to galvanised iron strip 4 mm upto 7.5 mtr long by means of bolts, nuts, check nuts and washers of galvanized iron and connection to earthing test point & earth dolly and including watering pipe medium grade GI 20mm bore & protection GI pipe light grade 15 mm bore, including wire mesh, funnel, lugs, salt, charcoal dust, excavation in any type of soil, returning filling & removal of surplus soil upto 50mtr, pit chamber shall be of PCC 1:2:4 type B1 using 20 mm graded mechnically crushed stone aggregates and pit cover slab 40mm thick shall be of Precast RCC 1:2:4 type B-1 using 20 mm graded mechnically crushed stone aggregates reinforced with XPM weighing not less than 4Kg/sqm including necessary form work complete all as shown in electrical plate No 3 of SSR part-I, including testing on completion at site complete all as specified and directed. Notes:- (i) Any variation in length of earth lead and protection pipe of earth lead shall be adjusted through DO. (ii) On testing if the desired earth resistance is not obtained, earthing will be generated at no extra cost , till the desired earth resistance is obtained. (iii) The chamber shall be constructed atleast 1.5 mtr away from the earth electrode

S & F electronic meters tamper proof LCD display with polycarbonate cover 230 V, 10-60Amp, accuracy class-I 50Hz, conforming to IS 13779, IP-54, with parameters to show data, time, current reading, load, PF, voltage and KWH complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 120 Sqmm 3.5 core complete all as specified and directed.

All as per Item No 12.00 here-in-above but cable of size 95 Sq mm 3.5 core complete all as specified and directed.

All as per Item No 12.00 here-in-above but cable of size 25 Sq mm 3.5 core complete all as specified and directed.

All as per Item No 12.00 here-in-above but cable of size 16 Sq mm 3.5 core complete all as specified and directed.

Excavation in trenches n exc. 1.5 m wide and n' exc. 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

M & L for sand cushioning to under ground cable, 8 cms thick before laying the cable and 15 cms thick after laying & stretching the cable in trenches, including hand punning and consolidating, complete all as specified and directed. Note: For payment purpose punned thickness shall be measured.

M & L for Bricks, old size sub class `B' laid in trenches with width wise along the alignment of the cable as protection complete all as specified and directed.

Returning, filling of excavated soil, including spreading leveling, watering and well ramming in layers, not exceeding 25cm complete all as specified and directed.

Removing of surplus soil to a distance n exc 50 m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed.

S & F 100 mm bore GI tubing in trenches /fixed on pole / wall of light grade, IS-1239 marked with required size of flat iron clamp duly painted with two coats of super enamal paint over a coat of red oxide primer complete with bolts, nuts and washers complete all as specified and directed.

All as per Item No 21.00 here-in-above but size of pipe 40 mm bore complete all as specified and directed.

S & F LT Control panel board, Outdoor type,double door, cubical type, padestal mounted, slopy roof, front and back both side opening, CPRI approved, IP -54 having independent compartment for bus bar, incoming feeder and each out going feeders, dust and vermin proof & lockable, factory made, fabricated out of 3.15 mm thick CRCA sheet suitable for 3 Phase 415 volts 50 Hz, AC supply, bus bar chamber with Aluminium bus bar of 400 Amp rating for 3 phase and bus bar of half capacity for neutral 3 phase 4 wire system duly insulated with heat shrinkable type sleeves as per colour code, supported on epoxy insulators - 01 Set incl necessary copper cables of suitable size for MCCBs/MCBs / change over swicth / inter connections, common earth bus bar of GI Strip 32 x 6 mm at bottom with panel board at two earth terminals, cable glands with independent plates at bottom for each out going and in coming cables in cable alley panel board and painted with powder coating in siemens grey colour and provision for the following incoming and out going accessories all as approved and comprising as under:- (a) Main Incomming: MCCB 200 Amps 4 Pole 25 KA -01 No (b) Outgoing (i) MCCB 160 Amps 4 Pole 25 KA-01 Nos (ii) MCCB 63 Amps 4pole 16 KA- 01 Nos (iii) Multifunctional Amp meter, Vol meter, KW meter etc-01 No (iv) Indicating lamp at all outgoings - 01 Job Notes:- (i) Panel shall be mounted on brick work plate form duly plastered and PCC copping work on top surface , height shall be 0.60 m above the GL and 0.40 M all around the FPB all as per direction of Engr-in-Charge. (ii) All incoming and out going cables shall be connected with suitable size of cable luggs and cable glands etc. '(iii) Angle iron base frame made out of ISA 5050 of size 50 x 50 x 6 mm thick angle iron duly painted with one coat of black synthetic enamel paint over two coats of red oxide incl PCC 1:3:6 (40 mm grade aggregate) type C2 for foundation , total leg height 750 mm and grouting in side pcc 300mm below ground level - 01 Job

S & F LT Control panel board, Outdoor type,double door, cubical type, padestal mounted, slopy roof, front and back both side opening, CPRI approved, IP -54 having independent compartment for bus bar, incoming feeder and each out going feeders, dust and vermin proof & lockable, factory made, fabricated out of 3.15 mm thick CRCA sheet suitable for 3 Phase 415 volts 50 Hz, AC supply, bus bar chamber with Aluminium bus bar of 400 Amp rating for 3 phase and bus bar of half capacity for neutral 3 phase 4 wire system duly insulated with heat shrinkable type sleeves as per colour code, supported on epoxy insulators - 01 Set incl necessary copper cables of suitable size for MCCBs/MCBs / change over swicth / inter connections, common earth bus bar of GI Strip 32 x 6 mm at bottom with panel board at two earth terminals, cable glands with independent plates at bottom for each out going and in coming cables in cable alley panel board and painted with powder coating in siemens grey colour and provision for the following incoming and out going accessories all as approved and comprising as under: (a) Main Incomming: MCCB 125 Amps 4 Pole 25 KA -02 No (b) Outgoing (i) MCCB 40 Amps 4 Pole 16 KA-04 Nos (ii) Multifunctional Amp meter, Vol meter, KW meter etc-01 No (iii) Indicating lamp at all outgoings - 01 Job Notes:- (i) Panel shall be mounted on brick work plate form duly plastered and PCC copping work on top surface , height shall be 0.60 m above the GL and 0.60 M all around the FPB all as per direction of Engr-in-Charge. (ii) All incoming and out going cables shall be connected with suitable size of cable luggs and cable glands etc. '(iii) Angle iron base frame made out of ISA 5050 of size 50 x 50 x 6 mm thick angle iron duly painted with one coat of black synthetic enamel paint over two coats of red oxide incl PCC 1:3:6 (40 mm grade aggregate) type C2 for foundation , total leg height 750 mm and grouting in side pcc 300mm below ground level - 01 Job

S & F LT MS cable route indicator, engraved the description "LT CABLE" on the disc not less than 6 inch dia and 6 mm thick welded with 40x6 mm MS strip of approximate length 90 cm duly painted on all steel parts as per colour code and provision of PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) of not less than 0.05 cum in each at base burried under the ground including necessary earth work complete all as specified and directed. Note: Cable route drawing to be submitted by the contractor and approved by the Accepting Officer.

M & L for earthing complete with galvanized iron strip 32×6mm as earthing lead thick buried directly vertically in ground to depth not less than 2.25 mtr below ground level, with top edge of earth plate not less than 1.5 mtr below ground level surrounded from all sides by 15 cm thick packed layer of Charcoal dust & common salt filled in alternate layers and electrode connected to galvanised iron strip 4 mm upto 7.5 mtr long by means of bolts, nuts, check nuts and washers of galvanized iron and connection to earthing test point & earth dolly and including watering pipe medium grade GI 20mm bore & protection GI pipe light grade 15 mm bore, including wire mesh, funnel, lugs, salt, charcoal dust, excavation in any type of soil, returning filling & removal of surplus soil upto 50mtr, pit chamber shall be of PCC 1:2:4 type B1 using 20 mm graded mechnically crushed stone aggregates and pit cover slab 40mm thick shall be of Precast RCC 1:2:4 type B-1 using 20 mm graded mechnically crushed stone aggregates reinforced with XPM weighing not less than 4Kg/sqm including necessary form work complete all as shown in electrical plate No 3 of SSR part-I, including testing on completion at site complete all as specified and directed. Notes:- (i) Any variation in length of earth lead and protection pipe of earth lead shall be adjusted through DO. (ii) On testing if the desired earth resistance is not obtained, earthing will be generated at no extra cost , till the desired earth resistance is obtained. (iii) The chamber shall be constructed atleast 1.5 mtr away from the earth electrode.

Taking down carefully unserviceable aluminum/copper point wiring (light/ fan/ socket/ power) complete including fittings such as switches, sockets, ceiling roses etc but excluding light fittings and exhaust fans etc removing and making good disturbed surfaces of wall/ceiling etc complete all as specified and directed.

M & L for point wiring with 1.5 Sq mm nominal area PVC insulated and unsheathed cable single core FRLS copper cable 1100 Volts with multistranded, copper conductor in and including PVC rigid concealed conduit (heavy grade) including chases cutting and making surface fair and matching with the existing paint as required on site and conduit accessories along with continous earth wire 1.5 sqmm PVC insulated and unsheathed single core FRLS cable 1100 Volts grade with standard copper conductor and connected to common earth dolly, with and including cadmium plated sunk Modular metal flush boxes for modular switches complete all as specified and directed. One light point controlled by one switch one way. Note:- modular white cover and plate with frame will be measured and paid saperately under respective item.

All as per Item No 28.00 here-in-before but for one celling / Exhaust fan point controlled by one switch one way complete all as specified and directed.

All as per Item No 28.00 here-in-before but for one socket out let 5 Amps 5 pin on independent board complete all as specified and directed.

All as per Item No 28.00 here-in-before but for one socket outlet 5 Amps 5 Pin on same board with other switches complete all as specified and directed.

All as per Item No 28.00 here-in-before but with size of cable 2.5 Sq mm for one 5 pin 15 Amps socket out let on independent board and multistrand insulated copper earth continuity conductor of size 1.5 sqmm all as specified and directed. Note: Circuit to be laid separately.

S & F in repair modular switch 1 way 6 amps 1 module complete all as specified and directed.

S & F in repair modular socket outlet 2/3 pin 6 Amps combined 2 module complete all as specified and directed.

S & F in repair modular socket 6A/16 A-2/3 pin combined 2 module complete all as specified and directed.

S & F in repair modular switch 1 way 16 amps 1 module complete all as specified and directed.

S & F Fan step regulator,120 W -2 module complete all as specified and directed.

S & F Bell push 6 A 1 module complete all as specified and directed.

S & F Buzzer, Ding Dong AC.230 Volts,single pole complete all as specified and directed.

S & F in repair white modular cover plate 2 module with frame for fixing of modular switches of following complete all as specified and directed.

All as per Item No 40.00 here-in-above for modular cover plate 3 module complete all as specified and directed.

All as per Item No 40.00 here-in-above for modular cover plate 4 module complete all as specified and directed.

All as per Item No 40.00 here-in-above for modular cover plate 6 module complete all as specified and directed.

All as per Item No 40.00 here-in-above for modular cover plate 8 module complete all as specified and directed.

All as per Item No 40.00 here-in-above for modular cover plate 12 module complete all as specified and directed.

S & F for modular blank spacer plate for single module complete all as specified and directed.

S & F in replacement of unserviceable VTPN double door,4 way IP 61439-3 protection with 250 A copper bus bar with 2 nuetral bus bar and earth bar fully insulated bus bar and shrouded neutral bars with MCCB 160 Amps, 4 Pole, 25 KA complete all as specified and directed.

Taking down old unserviceable TPN DB and supply & fix in repair MCB distribution board triple pole and neutral 4 way double door factory made sheet steel, phosphates, powder coated with 200 Amps rated bas bar, 415 volts, neutral link, earth bar and Din rail and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

Taking down old unserviceable DB and supply & fix in repair MCB distribution board single pole and neutral 12 way double door factory made sheet steel, phosphates, powder coated with 200 Amps rated bas bar, 240 volts, neutral link, earth bar and Din rail and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

Taking down old unserviceable DB and supply & fix in repair MCB distribution board single pole and neutral 8 way double door factory made sheet steel, phosphates, powder painted with 200 Amps rated bas bar, 240 volts, neutral link, earth bar and Din rail complete including making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

S & F MCB SP 06-32 Amps 10 Amps 10 KA rating, 240 Volts 'C' Curve type complete all as specified and directed.

S & F MCB SPN 32 Amps 10 KA rating, 240 Volts 'C' Curve type complete all as specified and directed.

S & F MCB TP 63 Amps 10 KA rating, 415 Volts 'C' Curve type complete all as specified and directed.

S & F MCB TPN 63 Amps 10 KA rating, 415 Volts 'C' Curve type complete all as specified and directed.

S & F Isolator FP 100 Amps 10 KA rating, 415 Volts 'C' Curve type complete all as specified and directed.

M & L for sub-main wiring with two single core FRLS PVC insulated, unsheathed, multistranded copper conductor cable of size 4X10 sqmm 1100 volts grade and including non metallic rigid 25 mm dia PVC casing caping with all fitting and fixing accessories and including PVC insulated unsheathed, multistranded copper conductor cable of size 2X6 sqmm for earth continuity conductor and including taking down old unserviceable sub main wiring and making good the disturbed surface complete all as specified and directed.

S & F ceiling rose surface bakelite with ISI mark, flush type with ISI mark three terminals complete all as specified and directed.

S & F in replacement of LED mirror light fitting, 10 Watt, 1000 lumens 6500K comprises of aluminium extruded channel, frosted diffuser, integrated electronic driver, IP 20 protection and all accessories pre-wired including connecting up complete all as specified and directed.

S & F in replacement of 20 Watt 6500K LED batten 2000 lumens cool light fitting with extruded aluminium housing four feet with integrated LED & electronic driver and all accessories pre-wired including connecting up complete all as specified and directed.

S & F in replacement recessed mounted 3600 lumens, 6500K, 2'x2' LED ceiling light fitting with 60mm width CRCA body, opal acrylic diffuser, electronic driver, system life 50000 hrs @ 70%, PF 0.95, THD <10%, CRI >80,etc and all accessories pre-wired including connecting up complete all as specified and directed.

S & F decorative metal crome wall lights with integrated 6 watt LED (warm white) 3000k, lumen output of 450lm complete all as specified and directed.

S & F in replacement bulk head fitting 5700k, 10 watt capacity, IP 65 rating along with with die cast aluminium housing with complete assembly and PC opal diffuser for uniform illumination suitable for wall/surface mounted complete all as specified and directed.

Supply, laying and testing cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) 1100 volts grade with stranded aluminium conductor of size 6 sqmm 4 core complete all as specified and directed.

S & F mount LED bollard with IP 65 protection excellent light output through its PMMA window ensuring maximum lumination aspects in sorroundings complete including PCC work as required at site complete all as specified and directed.

Balraj and Co (BID ID -3478026)

FATEH ENTERPRISES (BID ID -3482744)

R D Bansal (BID ID -3483139)

Bedi Refrigeration Works (BID ID -3475990)

SUBHASH CHAND CONTRACTOR (BID ID -3477535)