Supplying of Furniture for Hotel Holiday Home Shimla (H.P).

Amount

Providing & supplying single seater chair with arms of size 650X650X975 mm (LxWxH) made up of hard wood frame (only invisible frame ) double dowelled for proper strength, glued and screwed/nailed properly as per design/ photograph attached. The legs should be made of knot free teak wood as per design or as approved finished with PU polish (Asian or equivalent or as approved). The chair seat and backrest should be padded with polyurethane foam fully upholstered fabric of de-decor, dicitex retails or equivalent or of approved make with cost of fabric not less then Rs. 1000 /- per meter (Discounted rate) to be approved by HPTDC. All fabric to be stain and water resistence 3mm coating.The thickness of foam should be 4" thick having density of 40±2Kg/m3 with 1/5" soft foam on base foam (sleepwell, Century or equivalent conforming to BS 5952 Part 1 1979 Ignition Source O (Cigarette)) to provided extra softness & comfort to the chair including carriage of material within all leads, lifts and heights. Image attached at Annexure 'A' only for reference.

Providing & supplying single seater chair without arms of size 650X650X975 mm (LxWxH) made up of hard wood frame (only invisible frame ) double dowelled for proper strength, glued and screwed/nailed properly as per design/ photograph attached. The legs should be made of knot free teak wood as per design or as approved finished with PU polish (Asian or equivalent or as approved). The chair seat and backrest should be padded with polyurethane foam fully upholstered fabric of de-decor, dicitex retails or equivalent or of approved make with cost of fabric not less then Rs. 1000 /- per meter (Discounted rate) to be approved by HPTDC. All fabric to be stain and water resistence 3mm coating. The thickness of foam should be 4" thick having density of 40±2Kg/m3 with 1/5" soft foam on base foam (sleepwell, Century or equivalent conforming to BS 5952 Part 1 1979 Ignition Source O (Cigarette)) to provided extra softness & comfort to the chair including carriage of material within all leads, lifts and heights. Image attached at Annexure 'A' only for reference.

Providing & supplying single seater sofa of size 750x850x875mm (LxWxH) made up of hard wood frame (only invisible frame ) double dowelled for proper strength, glued and screwed/nailed properly as per design/snaps attached. The legs should be made of knot free teak wood as per design or as approved finished with PU polish (Asian or equivalent or as approved). The sofa should have coil springs in seats and sinuous spring for backrest, padded with polyurethane foam fully upholstered fabric of de-decor, dicitex retails or equivalent or as approved make with cost of fabric not less then Rs. 1200 /- per meter (Discounted rate). All fabric to be stain and water resistence 3mm coating. The thickness of foam should be 4" thick having density of 40±2Kg/m3 with 1/5" soft foam on base foam (sleepwell, Century or equivalent conforming to BS 5952 Part 1 1979 Ignition Source O (Cigarette)) to provided extra softness & comfort to the sofa. The necessary thickness of foam should be used for cushioning of front/side approns of sofa. All open area or base or invisible part of the sofa should be fully covered (as per the scheme specified )with base fabric including carriage of material within all leads, lifts and heights. Image attached at Annexure 'A' only for reference.

Providing & supplying 2 seaters sofa of size 1800X880X800mm (LxWxH) made up of hard wood frame (only invisible frame )double dowelled for proper strength, glued and screwed/nailed properly as per design/photograph attached. The legs should be made of knot free teak wood as per design or as approved finished with PU polish (Asian or equivalent or as approved). The arm should be finished in 75mm thick as per design/snaps. The back should have quilting as per snaps. The sofa should have coil springs in seats and sinuous spring for backrest, padded with polyurethane foam fully upholstered fabric of de-decor, dicitex retails or equivalent or as approved make with cost of fabric Rs. 1200/- per meter (Discounted rate). All fabric to be stain and water resistence 3mm coating. The thickness of foam should be 4" thick having density of 40±2Kg/m3 with 1/5" soft foam on base foam (sleepwell, Century or equivalent conforming to BS 5952 Part 1 1979 Ignition Source O (Cigarette)) to provided extra softness & comfort to the sofa. The necessary thickness of foam should be used for cushioning of front/side approns of sofa. All open area or base or invisible part of the sofa should be fully covered with base fabric. All loose cushions and padding tobe covered with approved Upholstry with Stain and water resistant 3M coating including carriage of material in all leads, lifts and heights. Image attached at Annexure 'A' only for reference.

Providing & supplying 4 seaters sofa of size 3600X2800X7100mm (LxWxH) made up of hard wood frame (only invisible frame )double dowelled for proper strength, glued and screwed/nailed properly as per design/photograph attached.The legs should be made of knot free teak wood as per design or as approved finished with PU polish (Asian or equivalent or as approved). The sofa should have coil springs in seats and sinuous spring for backrest, padded with polyurethane foam fully upholstered fabric of De-decor, dicitex retails or equivalent or as approved make with cost of fabric Rs. 1200/- per meter (Discounted rate). All fabric to be stain and water resistence 3mm coating. The thickness of foam should be 4" thick having density of 40±2Kg/m3 with 1/5" soft foam on base foam (sleepwell, Century or equivalent conforming to BS 5952 Part 1 1979 Ignition Source O (Cigarette)) to provided extra softness & comfort to the sofa. The necessary thickness of foam should be used for cushioning of front/side approns of sofa. All open area or base or invisible part of the sofa should be fully covered with fabric including carriage of material within all leads, lifts and heights. Image attached at Annexure 'A' only for reference.

Providing & supplying 2 seaters sofa with leathererite of size 1300X710X100 mm (LxWxH)/ as per site dimensions made up of hard wood frame (only invisible frame ) double dowelled for proper strength, glued and screwed/nailed properly as per design/photograph attached. The legs should be made of knot free teak wood as per design or as approved finished with PU polish (Asian or equivalent or as approved). The back should have quilting as per photograph. The sofa should have coil springs in seats and sinuous spring for backrest, padded with polyurethane foam fully the leathererite not less then Rs.1200/- per meter (Discounted rate). All fabric to be stain and water resistence 3mm coating. The thickness of foam should be 4" thick having density of 40±2Kg/m3 with 1/5" soft foam on base foam (sleepwell, Century or equivalent conforming to BS 5952 Part 1 1979 Ignition Source O (Cigarette)) to provided extra softness & comfort to the sofa. The necessary thickness of foam should be used for cushioning of front/side approns of sofa. All open area or base or invisible part of the sofa should be fully covered with base fabric. All loose cushions and padding tobe covered with approved Upholstry with Stain and water resistant 3M coating including carriage of material in all leads, lifts and heights. Image attached at Annexure 'A' only for reference. Note:- Measurements to be verified at site.

Providing & supplying reactangular table laminated (1 mm thick) having size 1500X900X750 mm, table top 25mm thick with a non stain and a non scratch surface. The edge band to match the laminate colour and texture. The base is MS powder coated plate 300mm x 300mm x 6mm thick 2 no's base plate (to match industry standards), the support in MS pipe section 80 x80x6 mm square (powder coated) pre-laminated teak ply (Greenply, mica or equivalent) colour/shade approved by HPTDC, including carriage of materials within all leads, lifts and heights. Image attached at Annexure 'A' only for reference.

Providing & supplying reactangular table laminated (1 mm thick) having size 1350X900X750 mm, table top 25mm thick with a non stain and a non scratch surface. The edge band to match the laminate colour and texture. The base is MS powder coated plate 300mm x 300mm x 6mm thick 2 no's base plate (to match industry standards), the support in MS pipe section 80 x80x6 mm square (powder coated) pre-laminated teak ply (Greenply, mica or equivalent) colour/shade approved by HPTDC, including carriage of materials within all leads, lifts and heights. Image attached at Annexure 'A' only for reference.

Providing & supplying reactangular table laminated (1 mm thick) having size 1200X900X750 mm, table top 25mm thick with a non stain and a non scratch surface. The edge band to match the laminate colour and texture. The base is MS powder coated plate 300mm x 300mm x 6mm thick 2 no's base plate (to match industry standards), the support in MS pipe section 80 x80x6 mm square (powder coated) pre-laminated teak ply (Greenply, mica or equivalent) colour/shade approved by HPTDC, including carriage of materials within all leads, lifts and heights. Image attached at Annexure 'A' only for reference.

Providing & supplying reactangular table laminated (1 mm thick) having size 900X900X750 mm, table top 25mm thick with a non stain and a non scratch surface. The edge band to match the laminate colour and texture. The base is MS powder coated plate 300mm x 300mm x 6mm thick 2 no's base plate (to match industry standards), the support in MS pipe section 80 x80x6 mm square (powder coated) pre-laminated teak ply (Greenply, mica or equivalent) colour/shade approved by HPTDC, including carriage of materials within all leads, lifts and heights. Image attached at Annexure 'A' only for reference.

Providing and supplying rectangular table veneered rectabgular table top with the legs should be made of knot free teak wood as per design table finished with a PU having size 1200x750x450 mm with 25mm thick pre-laminated teak ply (Grean ply or equivalent) with 1.8mm thick PVC edge binding tape with knots free teak wood legs finished in PU polish (Asian or equivalent) colour/shade approved by HPTDC, including carriage of materials within all leads, lifts and heights. Image attached at Annexure 'A' only for reference.

Providing & supplying round low table finished with Veneer 600 X 650 mm (DXHt) with a Walnut veneered to be laid in cross cut pattern with a 6 mm thick nickle finished MS section inserted in the legs and table top. The legs should be made of knot free teak wood as per design.The top edge to be 75mm thick with rounded edge including carriage of materials within all leads, lifts and heights. Veneer to be finished with PU polish (Asian or equivalent or as approved). Image attached at Annexure 'A' only for reference.

Providing & supplying single seater sofa chair of size 750x850x1000mm (LxWxH) (high wing chair) made up of hard wood frame (only invisible frame ) double dowelled for proper strength, glued and screwed/nailed properly as per design/snaps attached. The legs should be made of knot free teak wood as per design or as approved finished with PU polish (Asian or equivalent or as approved). The sofa should have coil springs in seats and sinuous spring for backrest, padded with polyurethane foam fully upholstered fabric of de-decor, dicitex retails or equivalent or as approved make with cost of fabric not less then Rs. 1200 /- per meter (Discounted rate). All fabric to be stain and water resistence 3mm coating. The thickness of foam should be 4" thick having density of 40±2Kg/m3 with 1/5" soft foam on base foam (sleepwell, Century or equivalent conforming to BS 5952 Part 1 1979 Ignition Source O (Cigarette)) to provided extra softness & comfort to the sofa. The necessary thickness of foam should be used for cushioning of front/side approns of sofa. All open area or base or invisible part of the sofa should be fully covered (as per the scheme specified )with base fabric including carriage of material within all leads, lifts and heights. Image attached at Annexure 'A' only for reference.

Providing & supplying bar stool in leathererite basic of size 540x440x640 mm (LxWxH) made up of hard wood frame (only invisible frame ) double dowelled for proper strength, glued and screwed/nailed properly as per design/ photograph attached. The legs should be made of knot free teak wood as per design or as approved finished with PU polish (Asian or equivalent or as approved). The chair seat and backrest should be padded with polyurethane foam fully upholstered fabric of de-decor, dicitex retails or equivalent or of approved make with cost of fabric not less then Rs. 1200 /- per meter (Discounted rate) to be approved by HPTDC. The thickness of foam should be 4" thick having density of 40±2Kg/m3 with 1/5" soft foam on base foam (sleepwell, Century or equivalent conforming to BS 5952 Part 1 1979 Ignition Source O (Cigarette)) to provided extra softness & comfort to the chair including carriage of material within all leads, lifts and heights. Image attached at Annexure 'A' only for reference.

ASHOKA FURNITURE PVT LTD

Savvy Craft