WORK SERVICES FOR CLEANING OF E/M INSTALLATION CUTTING OF VEGETATION, BUSHES, GRASS, CREEPER ETC IN DOMESTIC AREA, REPAIR/MAINT OF VARIOUS OUTDOOR E/M ASSETS INCLUDING FENCING, FILLING OF GRAVELS AND CONNECTED ITEMS AND REPAIR/MAINT OF DAMAGED CABLE

Amount

S&F in replacement of first aid kit box/emergency medical box wall mouted type made out of powder coated GI sheet of 18 gauge and the size of the box will be 36cm(H) x 26cm(W) x 13 cm(D) with front transparent acrylic glass and multi compartment 4 shelf for better organize of medicines with security lock on door, openable window at front side with help of hinge at one side and locking arrangement at another side, openable window must painted with "FIRST AID" with red paint and whole box will fixed on wall at height not less than 2mtr including medicene and other items as under :- (i) Sterilized dressings- 04 Nos, (ii) Cotton Wool 10 gm - 02 Nos, (iii) Antiseptic Solution (100 ml) - 01 No, (iv) Burn Ointment - 01 No, (v) Scissor - 01 No, (vi) Digital Thermometer - 01 No, (vii) Disposal Gloves - 02 Nos, (viii) Disposal Mask - 20 Nos, (ix) Adhesive / Microporous Tape 1/2" - 01 No, (x) Band- Aid - 10 Nos, (xi) Safety pins - 05 No, (xii) Cold Rub - 01 No, (xiii) Roller Bandage (5cm) - 02 Nos, (xiv) Roller Bandage 10 cm - 02 Nos, (xv) Cotton Buds - 10 Nos, (xvi) Hand Sanitizer - 02 Nos, (xvii) Handiplast - 12 Nos, (xviii) Antiseptic cream - 01 No, (xix) Antiallergic medicene, Cough medicene, Pain killer, Fever and cold medicene- 01 strip each and a First-Aid Guide booklet, complete all as specified and directed.

Uprooting grass/weeds/plants up to 30cm depth by scrapping soil in order to make free ground from all sort of vegetation (grass/weeds/plants) and hand packing carefully by packing round pebbles approximately of size 20 to 40mm after carefully picking form heap of pebbles/stones, complete all as specified and directed.

M & L for cleaning of vegetaion including spray chemicals for prevention of growth of weed and grass at E/M sub station area with spray gun as per the manufacturer's instructions, complete all as specified and directed

Supply and spreading unslaked lime at surrounding (avarage 300 gms per Sqm), complete all as specified and directed.

Supply and filling dry river sand at surrounding of E/M installations / sub stations /cable trenches including watering and consolidation, complete all as specified and directed.

Supply and filling crushed stone aggregate, free from any foreign particles, 25mm gradded, for spreading at E/M sub station area, complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars, manholes etc., separation of serviceable materials from the unserviceable, stacking the serviceable materials within 100m and disposal of unserviceable materials, debris and rubbish to a distance not exceeding 100m, complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, old size, burnt clay brick, straight or curved on plan exc 6 mtr mean radius built in CM (1:6), complete all as specified and directed.

All as per item No. 8.00 here-in-before but except bricks, complete all as specified and directed. Note : (i) Bricks obtained from demolition shall be re-used. (ii) The quoted rate shall deemed to be included for cleaning of old bricks obtained from demolition.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM (1:6) and finished even and smooth without using extra cement, complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying three coats of white wash, complete all as specified and directed.

M&L for complete removal of existing treatment of old painted steel or iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint (1st grade quality), complete all as specified and directed

Demolition of unreinforced cement concrete in ground floors and paving n. exc. 15cm thickness (below or above ground level) and disposal of unserviceable materials, debris and rubbish to a distance not exceeding 100m, complete all as specified and directed.

M & L for PCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in coping/benching including necessary formwork etc, complete al as specified and directed.

M&L 75mm thick PCC (1:3:6 ) type C-2, (using 40mm graded stone aggregate) for sub base of floor, plinth prtection, path/hard standing etc, complete all as specified and directed.

M&L for mild steel chequered plate Fe-290 (Grade-E-165) 5mm or over thickness confirming to IS 1730-1981 as in duct covering placed over existing angle iron frame work or provision new frame work where necessary including connection of suitable number earth strip welded properly and making good to th existing surface of duct, complete all as specified and directed.

Supply and laying synthetic rubber insulated mats 2.5mm thick of size 2m x 1m for voltage upto 3.3 kv for electrical purpose as per IS 15652-2006, (superseding IS 5424) suitable for electrical shock safety, complete all as specified and directed.

Supply, fabricating, installation, testing and commissioning of back-lit signage board including embedding the board firmly with the wall/MS angle frame/as per approved art work and nomenclature as under :- Box with frame :- 25 x 25mm square pipe (18 gauge) frame with cross supports @ spacing not exceeding 1.0m on the box length including 20mm x 20mm MS Square pipe (18 gauge) stiffeners duly painted with two coats of white synthetic enamel paint (1st grde quality) over a coat of zinc oxide iron primer, depth of box should not be less than 165mm. Side, Top, Back and bottom Panels :- Made out of 24 gauge chemically treated GI Sheets duly powder coated with white matt finish coating on both inner and outer surfaces. Top panel made out of 24 gauge chemically treated GI sheet, duly powder coated, drip cap (fixed with pop rivet or machine moulded to shape) of 25mm on front and side to prevent damages due to rain etc. The bottom panel should be provided with access door fixed with stainless steel screws and suitable housing for LED drivers. LED Module :- LED 12V module beam angle >=150 degrees with IP rating >= 64, 0.72 W/70 lumens per module of 3 LEDs with 7000 to 8000 K colour temperature. LED configuration :- 29 LED modules per Sqm (equal division on spacing based on height of box) and one module every 0.20 m on running length of box. LED power supply :- Input 230 V AC, power supply should be CPCC (constant power constant current) of 30W/60W/120 W. Graphics :- Graphics shall be computer plotter cut with translucent cast vinyl matching the colour specification of the installation.

M&L for earthing complete with GI earth plate electrode 60 × 60cm × 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to existing earth lead GI strip 25 X 4mm by means of bolts, nuts, check nuts and washers of brass or HS steel all as shown in electrical plate No. 3 connected to earthing test point and and necessary excavation and earth work PCC (1:3:6) type C-1 as earth pit with pre-cast RCC (1:2:4) type B-1 cover slab size 400 x 400 x 50mm reinforced with 8mm dia TMT bar, 100mm c/c both ways including one handle made of 12mm dia including providing charcoal or coke and common salt in alternate layer of 15cm compacted thickness all around the earth electrode with funnel and 20mm bore galvanized iron watering pipe (light grade) wire mesh, copper lugs, complete in all respect, including galvanised iron earth strip 25 x 4mm, protected by 40mm bore (medium grade) galvanized iron pipe up to earthing test point as directed, incl disposal of spoil to a distance not exc. 50 mtr and necessary testing on completion, complete all as specified and as directed. Note : Proper earthing pit should be provided with pit cover.

S&F post top lantern LED type 20/25 watt AC 230 volts outdoor type with decorative post top for 360 degree indirect light IP 65/66 protection with impact and corrosion resistant complete with driver and lamp including taking down old unserviceable LED light fittings of any description, complete all as specified and directed.

S&F post top lantern LED type 40/45 watt AC 230 volts outdoor type with decorative post top for 360 degree indirect light IP 65/66 protection with impact and corrosion resistant complete with driver and lamp including taking down old unserviceable LED light fittings of any description, complete all as specified and directed.

S&F LED street light fittings 60 watt 230 v AC outdoor type with high pressure dia cast aluminium housing and heat-resistant complete with driver, lamp bracket with impact and corrision resistant, IP 65/66 protection including taking down old unserviceable LED light fittings, complete all as specified and directed.

S & F in repair pre-casted LT cable rout marker made from RCC (1:2:4) (using 20mm graded crusded stone aggregate) reinforced with 10mm dia TMT bar, 3 Nos with length and 5 Nos. with width, size 1200mm x 300mm x 100mm, marked as "MES CABLE" and painted with two coats of synthetic enamel paint (yellow colour) over a coat of cement primer, complete all as specified and directed. Note : Excavation and earth work shall deemed to be included in the unit quoted rate.

S&F in possition Heavy duty cable tray of the size 300mm wide x 25mm height for supporting/fixing 1100 Volts grade armoured/unarmoured aluminium/copper conductor cables, fabrication from angle and perforated 2mm thick CRCA sheet, powder coated, with expansion coupler plates, galvanised, with bolts, washer and nuts, knock out holes for cable connections, complete all as specified and directed.

M & L for spray painting with synthetic enamel paint (1st grade quality) of approved colour for transformer, voltage stabilizer, isolation transformer and other similar equipment upto 150 KVA including preparation of surfaces, cleaning, scrapping etc, complete all as specified and directed.

M & L for spray painting with synthetic enamel paint (1st grade quality) of approved colour for transformer, voltage stabilizer, isolation transformer and other similar equipment exceeding 150 KVA and upto 250 KVA including preparation of surfaces, cleaning, scrapping etc, complete all as specified and directed.

M & L for spray painting with synthetic enamel paint (1st grade quality) of approved colour for transformer, voltage stabilizer, isolation transformer and other similar equipment exceeding 250 KVA and upto 400 KVA including preparation of surfaces, cleaning, scrapping etc, complete all as specified and directed.

M & L for spray painting with synthetic enamel paint (1st grade quality) of approved colour for transformer, voltage stabilizer, isolation transformer and other similar equipment exceeding 400 KVA and upto 750 KVA including preparation of surfaces, cleaning, scrapping etc, complete all as specified and directed.

M & L for detecting fault through cable fault deductor by injecting suitable energy pulse to detect exact position of fault for XLPE, LTcable, 1100 volts grade heavy duty aluminium conductor any size including transporting chagres and clearing of rectification of fault of electric supply by removing of burnt out portior of cable from loop, etc including earth work, complete all as specified and directed.

S&F in repair danger notice plate of 1.6mm thick mild steel sheet, vitreous enamelled white, with letters, figures and conventional skull and bones in signal red colour and fixed with M.S. clamps, bolts and nuts of approved size, 20 x 15cm size, complete all as specified and directed.

M&L for sealing of cable entry portion in order to make LT panel/HT panel/RMU/VCB panel dust and vermin proof by using loctite tite foam PU sealant, white, expanding foam for large gap filling, complete all as specified and as directed.

M&L for preparation of old painted steel or iron surfaces of any description over 10cm width or girth for panel board, E/M plant & equipments etc. and applying two coats of synthetic enamel paint (1st grade quality) using spary painting machine, complete all as specified and directed

Supply, installing and commissioning of outdoor type bus bar panel box (size 900mm x 900mm x 450mm) made out of 3.15mm thick CRCA sheet, out door type, CPRI approved, totally enclosed weather, dust and vermin proof as per IS with front and rear , copper bus bar 400 Amp capacity for RYB and half for neutral and insulated with insulators, including connecting incoming and outgoing cables necessary made out of 50 x 50 x 6mm angle iron grouted at floor above 30cm from ground level including foundation with PCC (1:2:4) type B-1, of required size, including taking down old unserviceble box, complete all as specified and directed.

S&F water proof junction box made from SMC/FRP sheet ready made of size 140 x 140 x 95mm with aluminium bus bar of 50 Amp capacity for RYB and neutral fixed inside the junction box with necessary supporting insulators fixed on hylem sheet /insulating sheet, MS sheet steel fixed inside the bottom portion of box to connect the cable gland complete , entire assembly fixed to pole /wall with MS clamp 15 x 3mm and nuts & bolts,and connecting cables from junction box to fittings, complete all as specified and directed.

M&L for painting PCC poles, 8.5 meter in height above GL including cross arms and bracings on existing surface after cleaning and removing dust, rust & dirt with two coats of cement based paint over a coat of alkali resistant primer painting with black & white alternate strips of 30cm each externally from ground level up to 1.5 mtr with synthetic enamel paint numbering of pole, complete all as specified and directed.

M&L for painting steel tubular poles, 8.5 meter in height above GL including cross arms and bracings on existing surface after cleaning and removing dust, rust & dirt by applying two coats of aluminium paint painting over a coat of red oxide primer with black & white alternate strips of 30cm each externally from ground level up to 1.5 mtr with synthetic enamel paint and numbering of pole, complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 300 Sqmm 3.5 core including taking down old unserviceble cable, complete all as specified and directed.

All as per serial item No. 37.00 here-in-before but size 240 Sqmm 3.5 core, complete all as specified and directed.

All as per serial item No. 37.00 here-in-before but size 120 Sqmm 3.5 core, complete all as specified and directed.

All as per serial item No. 37.00 here-in-before but size 95 Sqmm 3.5 core, complete all as specified and directed.

All as per serial item No. 37.00 here-in-before but size 70 Sqmm 3.5 core, complete all as specified and directed.

Lifting of existing cable PVC/XLPE insulated, armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor, including cable protection (GI pipe, brick etc), in trenches/fixed on wall, cross sectional area 300 sqmm to 400 Sqmm 3.5 core, including re-laying the cable at same or other location. complete all as specified and directed. Note: (i) Necessary earth work shall be measured and paid separately. (ii) Cost of lugs of suitable size and cable gland irrespective of length of cable shall deemed to be included in the unit quoted rate.

All as per itme No 42.00 here-in-before but 185 Sqmm to 240 Sqmm 3.5 core, complete all as specified and directed.

All as per itme No 42.00 here-in-before but 70 Sqmm to 120 Sqmm 3.5 core, complete all as specified and directed.

Supply and laying in trenches/fixed on wall 80mm bore GI tubing, light grade, with necessary fittings such as bend, tee, elbow etc for protection of LT UG cable, complete all as specified and directed.

Supply and laying in trenches/fixed on wall 50mm bore GI tubing, light grade, with necessary fittings such as bend, tee, elbow etc for protection of LT UG cable, complete all as specified and directed.

Supply and laying in trenches or fixed to wall double walled corrugated (DWC) HDPE duct pipe of 50mm outer dia conforming to IS, approved colour complete with fittings for cable protection including taking up/down old unserviceable pipe, complete all as specified and directed.

Supply and laying in trenches or fixed to wall double walled corrugated (DWC) HDPE duct pipe of 75mm outer dia conforming to IS, approved colour complete with fittings for cable protection including taking up/down old unserviceable pipe, complete all as specified and directed.

Excavation in trenches n. exc. 1.5m wide and n. exc. 1.5m in deep for foundation etc. or for shaft, wells, cesspits, manhole, pair house etc. n. exc. 10 Sqm on plan and getting out in any type of soil, complete all as specified and directed.

Returning filling in incl spreading, leveling watering and well ramming in layers not exceeding 25cm in soft/loose soil, complete all as specified and directed.

Removing excavated materials to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 metre above the starting point in any type of soil, complete all as specified and directed.

Supply and laying well burnt sub class 'B' bricks, old size, laid in trenches perpendicular to UG cable, laid flat, (width of brick along the length of cable) over sand cushioning for cable protection, complete all as specified and directed.

Laying only old bricks, sub class 'B' laid in treches perpendicular to UG cable, laid flat, (width of brick along the length of cable) over sand cushioning for cable protection, complete all as specified and as directed. (Note : Serviceable bricks obtained from itmem No. 42.00 taking down of XLPE cable shall be re-used)

S&F water proof junction box made from SMC sheet ready made of size 350 x 270 x 21mm with aluminium bus bar of 150 Amp capacity for RYB and neutral fixed inside the junction box with necessary supporting insulators fixed on hylem sheet /insulating sheet ,MS sheet steel fixed inside the bottom portion of box to connect the cable gland complete , entire assembly fixed to pole /wall with MS clamp 25 x 5mm and nuts & bolts,and connecting cables from junction box to fittings, complete all as specified and directed.

All as per itme No 54.00 here-in-before but size 400 x 350 x 190mm with aluminium bus bar of 200 Amp capacity, complete all as specified and directed.

Horizontal boring under the road (with manual method) below 1mtr from the road surface and dia of hole not exc 100mm, with out damaging the existing road, getting out and disposal of soil to a distance not exceeding 50m from the site of work, complete all as specified and directed.

M&L straight through joints (epoxy) cable joint kit including jointing materials for making joints of UG electric cable 1100 volt grade heavy duty with PVC/XLPE insulated aluminium conductor nominal cross sectional area 10 to 16 Sqmm 3.5/4.0 core and testing, complete all as specefied and directed.

M&L straight through joints (epoxy) cable joint kit including jointing materials for making joints of UG electric cable 1100 volt grade heavy duty with PVC/XLPE insulated aluminium conductor nominal cross sectional area 25 to 50 Sqmm 3.5/4.0 core and testing, complete all as specefied and directed.

M&L straight through joints (epoxy) cable joint kit including jointing materials for making joints of UG electric cable 1100 volt grade heavy duty with PVC/XLPE insulated aluminium conductor nominal cross sectional area 70 to 150 Sqmm 3.5/4.0 core and testing, complete all as specefied and directed.

M&L straight through joints (epoxy) cable joint kit including jointing materials for making joints of UG electric cable 1100 volt grade heavy duty with PVC/XLPE insulated aluminium conductor nominal cross sectional area 185 to 240 Sqmm 3.5/4.0 core and testing, complete all as specefied and directed.

M&L straight through joints (epoxy) cable joint kit including jointing materials for making joints of UG electric cable 1100 volt grade heavy duty with PVC/XLPE insulated aluminium conductor nominal cross sectional area 300 to 400 Sqmm 3.5/4.0 core and testing, complete all as specefied and directed.

M&L for earthing of equipment complete with copper earth plate electrode 60 x 60cm.× 3.00mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to existing earth lead strip by means of bolts, nuts, check nuts and washers of brass or HS steel all as shown in electrical plate No. 3 connected to earthing test point and and necessary excavation and earth work PCC (1:2:6) type C-1 with suitable size of CI cover plate with angle iron frame and opening arrangement ) incl providing charcoal or coke and common salt in alternate layer of 15cm compacted thickness all around the earth electrode with funnel and 20mm bore galvanized iron watering pipe (light grade) wire mesh, copper lugs, complete in all respect,including copper earth strip 25 x 3.00mm, 40mm bore (medium grade) galvanized iron pipe up to earthing test point as directed, incl disposal of soil to a distance not exc 50 mtr and necessary testing on completion including taking down/dismantling of old unserviceable earthing of any description, complete all as specified and directed. Note : (i) Earth result after installation completely should be less than 5 Ohm. (ii) Copper earth strip beyond 7.5m shall be measured and paid separately under appropriate item.

S&F copper earth strip of size 20 x 3mm laid in trench/ wall/ floor with necessary supporting insulators in regular interval as directed from earh test point to terninal point with double nut bolt joint at starting terminal, complete all as specified and directed.

S&F in repair MCCB 415 V, AC, 4 pole, 63 Amps, 16 KA, breaking capacity, Ics=100%, ICU, as per IS/IEC 60947-2 with thermal magnetic protection unit, complete all as specified and as directed.

S&F in repair MCCB 415 V, AC, 4 pole, 100 Amps, 16 KA, breaking capacity, Ics=100%, ICU, as per IS/IEC 60947-2 with thermal magnetic protection unit, complete all as specified and as directed.

S&F in repair MCCB 415 V, AC, 4 pole, 125 Amps, 16 KA, breaking capacity, Ics=100%, ICU, as per IS/IEC 60947-2 with thermal magnetic protection unit, complete all as specified and as directed.

S&F in repair MCCB 415 V, AC, 4 pole, 160 Amps, 25 KA, breaking capacity, Ics=100%, ICU, as per IS/IEC 60947-2 with thermal magnetic protection unit, complete all as specified and as directed.

S&F in repair MCCB 415 V, AC, 4 pole, 200 Amps, 25 KA, breaking capacity, Ics=100%, ICU, as per IS/IEC 60947-2 with thermal magnetic protection unit, complete all as specified and as directed.

S&F in repair MCCB 415 V, AC, 4 pole, 250 Amps, 36 KA, breaking capacity, Ics=100%, ICU, as per IS/IEC 60947-2 with thermal magnetic protection unit, complete all as specified and as directed.

S&F in repair MCCB 415 V, AC, 4 pole, 315/350 Amps, 36 KA, breaking capacity, Ics=100%, ICU, as per IS/IEC 60947-2 with thermal magnetic protection unit, complete all as specified and as directed.

S&F in repair air termination rod, single pointed copper rod 12mm dia and 300mm long, complete all as specified and directed.

Note: An amount of Rs.43,868.00 on account of Credit Schedule for schedule 'A' part - II shall be deducted from the total amount of BOQ to arrive at the contract sum.

M/S. NARENDRA KUMAR GARG (BID ID -3388652)

M/S BISHAL ENTERPRISES (BID ID -3388666)

M/S RATHIN ENTERPRISES (BID ID -3388883)

M/S BIJAY KUMAR SHIVA (BID ID -3388892)

M/S ROY ENTERPRISE (BID ID -3388899)