REPAIR REPLACEMENT TO FLOORING PLASTERING ROOFS AND MISC BR WORKS TO BLDGS OF SECTOR C UNDER AGE BR I OF GE 865 EWS

Amount

M&L for 15mm thick rendering on other than fair faces of brick works finished even and smooth without using extra cement in cement mortar 1:4 including taking down cement plaster on brick or concrete surfaces including racking out joints hacking for key, scrubbing down with water etc. complete all as specified and directed.

M&L for 15mm thick rendering on fair faces of brick works in cement mortar 1:6 finished even and smooth without using extra cement in cement mortar including taking down cement plaster on brick or concrete surfaces including racking out joints hacking for key, scrubbing down with water etc. complete all as specified and directed.

M&L for applying two coats of oil bound distamper on newly plastered surfaces of desired finish as approved by Eng-in-charge.

M&L for two coats cement base paint on newly plastered surfaces including preparation of surfaces complete all as specified and directed.

M & L for 25 mm thick, plain cement concrete, 1:2:4 (Nominal Mix), type B-0 (using 12.5 mm graded crushed stone aggregates) as in floors finished rough surface to receive floor finishes, including demolition of cement concrete (unreinforced) of any descriptions, in ground floors not exc.15 cm thick, above or below ground level complete all as specified and directed.

M&L for Vitrified ceramic tiles light shade 10 mm thick (square/rectangular) polished, area of each tile not exc. 0.36 Sqm in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6) including dismantling floor, hearth or wall tiling including cement mortar bedding (but including backing coat any number of layer complete), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for 10 mm thick non skid coloured ceramic tiles (area of each tile exc 0.06 and nexc 0.11sqm) etc set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments including 15 mm thick screed bed or bedding layer of cement mortar (1:6) including dismantling floor, hearth or wall tiling including cement mortar bedding (but including backing coat any number of layer complete), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for (300x200x7/350mmx250mmx7mm/450mmx350mmx 7mm thick ) coloured ceramic tiles set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments.(Note: Any disturbed surfaces shall be matched w/o any extra cost to the govt) including 10mm thck screed bed in CM 1:4 below tile for dado/skirting and including dismantling floor, hearth or wall tiling including cement mortar bedding (but including backing coat any number of layer complete), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for 75 mm thick cement concrete type D-2,1:4:8 (using 40mm graded crushed stone aggreate) as in sub -floors, sub- bases, floors and pavings, etc including demolition of cement concrete (unreinforced) of any descriptions, in ground floors not exc.15 cm thick, above or below ground level complete all as specified and directed.

M&L for Chequred cement concrete tiles 30cm X 30cm X 20mm thick, set, pointed and jointed in neat cement slurry in floors polished with grey cement and pigments layed over and including 20mm thick cement screed base in cm (1:6) including dismantling floor, hearth or wall tiling including cement mortar bedding (but including backing coat any number of layer complete), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Dismantling plain or corrugated steel sheeting any gauge thickness including nanital or similar pattern complete all as specified and as directed.

S&F 0.63mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275 complete all as specified and as directed.

Fixing only 0.63mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275 complete all as specified and as directed.

S&F 0.63mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and as directed.

S &F Pre-painted galvanum aluminum zink coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550MPa as in roof covering /clading to walls fixed with self tapping screws complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Fibre glass reinforced translucent plain sheeting 2mm thick with two corrugations side lap fixed with coach screw and washer in roof, wall etc complete all as specified and as directed.

M&L for 2nd class soft wood clean sawn timber fixed as in scatling fixed with nails including dismantling of timber scantling over 40Sqcm in section (unframed) in any position complete all as specified and as directed.

S&F mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 including dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

S&F rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, Fe 410, Gde E-250 including dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

M&L for two coats of synthetic enamel paint on new galvanised corrugated sheets including preparation of new zinc or galvanised surface to receive paint over a coat of red oxide and treatment with mordant solution complete all as specified and as directed.

M&L for two coats of synthetic enamel paint on new steel surfaces including preparation over a coat of red oxide Zinc chrome primer complete all as specified and as directed.

M&L for one coats of synthetic enamel paint on old decorated steel surfaces including preparation of surface complete all as specified and as directed.

S&F 3mm thick glass sheet any size oridinary quality in steel or wooden frames n exc 0.5 Sqm in each pane with fixing materials such as putty glazing pins wooden beads etc including hacking out old broken glasses (any thickness, size quality, description) from wooden or steel frames fixed with putty or wooden beads complete all as specified and as directed.

Dismantlng wooden fillets, rails, posts, rafters, purlins, grids for ceiling & wall panelling etc under 40 Sqcm in secton.(Framed work) complete all as specified and as directed.

S&F anodised aluminium snap grid of size 605 x 605mm, frame work of false ceiling including 6mm dia G.I. hangers (up to 1200mm length ) adjusting level fixed to roof slabs by means of ceilling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified and directed.

M&L for providing and fixing Gypsum board 12mm thick 600x600mm in size in ceiling fixed with screw or with staples on snap grid as per manufactures instructions, including dismantling wall/floor and ceiling boards (fiber, pulp, inlsulation, blankets) any thickness including covered fillets and supporting members complete all as specified and directed.

M&L for 2nd class soft wood clean sawn as in battens for grids of ceiling and lining fixed with nails exc 13 sqcm and nexc 25 sqcm in section complete all as specified and as directed.

M&L for 2nd class soft wood clean sawn as in beeding for edges of Ceiling, lining, or wooden flooring work fixed with nails exc 6 sqcm and nexc 13 sqcm in section complete all as specified and as directed.

M&L for covered fillets of standard hard board not less than 6mm thick and up to 40mm wide and fixing with screws complete all as specified and as directed.

M&L for 6mm (5 ply) thick veneered decorative (Knoty Pine) plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed with nails to timber frame work including dismantling wall/floor and ceiling boards (fiber, pulp, inlsulation, blankets) any thickness including covered fillets and supporting members complete all as specified and directed.

M&L for 6mm (5 ply) thick veneered decorative (Knoty Pine) plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed with nails to timber frame work as in Ceiling including dismantling wall/floor and ceiling boards (fiber, pulp, inlsulation, blankets) any thickness including covered fillets and supporting members complete all as specified and directed.

M&L for French polishing on wood or wood based surface of any width or girth or any description, including cleaning and preparing the surface including a coat of wood filler on new surface with two or more coats complete all as specified and as directed.

M&L for 9mm thick prelaminated particle board medium interior grade, prelaminated one side with decorated choice lamination and other side balancing white lamination fixed with screws to timber frame work as in wall panelling, shelves/boarding including dismantling wall/floor and ceiling boards (fiber, pulp, inlsulation, blankets) any thickness including covered fillets and supporting members complete all as specified and directed.

M&L for 9mm thick prelaminated particle board medium interior grade, prelaminated one side with decorated choice lamination and other side balancing white lamination fixed with screws to timber frame work as in ceiling, shelves/boarding including dismantling wall/floor and ceiling boards (fiber, pulp, inlsulation, blankets) any thickness including covered fillets and supporting members complete all as specified and directed.

Schedule of Credit

M/S WEB COMPNAY (BID ID -3121704)

M/S GEE AAR and SONS ENTERPRISES (BID ID -3124714)

M/S MOHD KARIM (BID ID -3124724)

N K BUILDERS (BID ID -3124495)