Repair and Renovation and Face Lifting at PWD (RnB) J.E Quarter Katra

Amount

Demolishing brick tile covering in terracing including stacking of serviceable material and disposal of unserviceable material within 50 metres lead.

Demolishing mud phaska in terracing and disposal of material within 50 metres lead

Demolishing cement concrete manually/by mechanical means including disposal of material within 50 metres lead: 1:3:6 or richer mix

Demolishing R.C.C. work manually/by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead .

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead: of area of 3 sq.metres and below

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound@ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 em. (c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg./sqm. and coarse sand @1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately) For the purpose of measurement the entire treated surface will be measured.

10cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa at 35kg per cum of earth and gobri leaping with bhusa at 35kg per cum of earth and gobri leaping with mix 1:1 ( 1 clay: 1 cow dung) and covered with flat tile bricks of class designation 100 grouted with cement mortar 1:3 (1 cement: 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finishing neat.With Hand moulded F.P.S brick tiles.

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement: 3 finesand) as per standard design : In 75x75 mm deep chase

Making khurras 45x45 em with average minimum thickness of 5 em cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing on wall face unplasticised - Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Completer job.110 mm diameter

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to lS: 15622 of approved make in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete Size of tile 60x60cm

Kota stone slab flooring over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1:4 (1 cement: 4 coarse sand) : 25 mm thick

Kota stone slab 25mm thick in risers of steps, skirting,dado and pillars laid on 12 mm ( average) thick cement mortar 1:3 (1 cement:3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Extra for Nosing in Steps and Treads of Kotra Stone Slab

Providing and fixing gang saw cut mirror polished (premoulded and pre polished), machine cut for kitchen platform, vanity counters window sills facias and similar locations of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels. 18mm thick

Extra for providing edge moulding to 18 mm thick marble stone counters, Vanities etc. over item no. 8.2 including machine polishing to edge to give high gloss finish etc.complete as per design approved by Engineer-in-Charge

Providing and fixing Ceramic glazed floor tiles 300x300mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 13755 of NITC.O, ORIENT,SOMANY, KAJARIA or equivalent make in colour such as White, Ivory, Grey, Fume Red, Brown laid on 20 mm thick bed of Cement Mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing 1st quality ceramic glazed tiles conforming to IS :·13753 of minimum thickness 5 mm of approved make like NITCO, ORIENT, SOMANY KAJARIA, or equivalent make in all colour, shades except begundy, bottle green, black of any size as approved by Eningeer in-charge in skirting, risers of steps and dados over 12 mm thick bed of Cement Mortar 1:3 ( 1 cement: 3 coarse sand) and jointing wtih grey cement slurry@ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Repairs to plaster of thickness 12mm to 20 mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 metres lead : With cement mortar 1:4 (1 cement: 4 fine sand)

Providing wood work in frames of doors, windows, clerestory windows and other frames and others frames, wrought framed and fixed in position with hold fast lugs or with dash fasterners of required dia and length (hold fast lugs or with dash fasterners shall be paid for separately) sal wood

Providing and fixing glazed shutters for doors, windows and clerestory windows using 10Kg/sqm (4mm th.) float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws Second class deodar wood

Providing and fixing 35mm thick wire gauge shutters using galvanised M.S. wire gauge of average width for aperture 1.4 mm in both direction with wire of dia. 0.63mm for doors, windows and clerestory windows with hinges and necessary screws Second class deodar wood

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 1 0mm diameter bolts, nuts and wooden plugs and em beddings in cement concrete block 30x1 0x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size )

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands,plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement with 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Reinforcement for RCC work incl. straightening, cutting, bending, placing in position and binding all complete including all leads, lifts and carriages complete.

Renewing glass panes, with wooden fillets wherever necessary : Glass panes weighing 10 kg I sqm Glass window

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade : One or more coats on old work.

Applying one coat of water thinable cement primer of approved brand and manufacture on wall surface Water thinable Cement primer

Finishing walls with Acrylic smooth exterior paint of required shade on Old work (two or more coats applied @ 1.67 litres/ 10 sqm on existing cement paint surface)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: One or more coats on old work

Providing and fixing brass bib cock of approved quality.15 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions 30 em length 15 mm nominal bore

Providing and fixing brass stop cock of approved quality 15 mm nominal bore

Providing and fixing gun metal gate valve with C.l. wheel of approved quality (screwed end) 25 mm nominal bore

Providing and fixing 100 mm sand cast iron grating for gully, floor or Nahani trap.

Providing and fixing PTMT soap dish holder having length of 138mm, breadth 1 02mm, heigth of 75mm with concealed fitting arrangements, weighing not less than 106gms

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour:600 mm long towel rail with total length of 645 mm, 78 mm wide and effectiveheight of 88 mm, weighing not less than 190 gms.

Providing and fixing PVC waste pipe for sink or wash basin including PVC waste fittings complete: Semi Rigid pipe 32mm diameter

Providing and fixing mirror of superior glass( of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing Rectangular shape 453x357 mm

Providing and placing on terrace (at all floor levels) polyethylene water storage tank lSI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank [Sintex, Electroplast, Star, Lotus or equivalent having valid lSI license].

Steel work in built up tubular round, square or rectangular including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer including welding and bolting with special shaped washers etc.complete. Hot finished welded type tubes

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work

Providing and fixing aluminium handles lSI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. 125mm

Providing and fixing aluminium tower bolts lSI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :

6mm cement plaster to ceiling of mix 1:3 (1 cement: 3 fine sand) including all leads, lifts and carriages complete.

12mm thick cement plaster of mix 1:4 (1cement: 4 fine sand) including all leads, lifts and carriages complete.

Centering and shuttering incl. strutting, propping etc. and removal of form work for including all leads, lifts and carriage complete:-

Suspended floors, roofs, landing, balconies and access platforms.

Edges of slabs and breaks in floors under 20cm wide.

Engangement of Labour for J.E quarter clearance for side drain, clearance around lawn and Roof Top and Sunshade along the Periphery at J.E quarter

Providing and Fixing of LED Bulb.

Engangement of 2no. Carpenter and 2no helper for setting and fixing of existing Panels

Carpenter

Helper

Engagement of labour for repair /checking supply of water in bothrooms etc

Plumber

Helper

M/S Mohit Dubey

Kaku Ram

CHURA MANI SHARMA

RAJINDER KUMAR SHARMA