REPAIR OF ROOF, FLOOR, JOINERY, FALSE CEILING, PLUMBING, SANITARY FITTINGS, TILING, BRICK WORK, PERIODICAL SERVICES, FENCING / GATE, PATH, DRAIN AND REPAIR / REPLACEMENT OF INTERNAL WIRING FITTINGS AND FIXTURES AT TECH AND DOMESTIC AREA AT 273 SU AFS

Amount

Dismantling of wrought or mild steel work of any description or otherwise provided for complete all as specified and directed.

M&L for steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt, welded tubes conforming to IS: 1161-1979, grade ST-240 complete all as specified and directed.

Dismantling asbestos cement (corrugated, semi corrugated etc) sheet in roof coverings incl ridges complete all as specified and directed.

M&L for Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

Demolition of cement concrete in ground floor and paving not exceeding 15 cm thick (above and below ground level) complete all as specified and directed. Note: All debris obtained from demolition shall be removed 1.5km to 2km complete all as specified and as directed.

M&L 40 mm thick cement concrete type B1 1;2:4 (20 mm graded stone aggregatge) finishing concrete surface even and fair without using extra cement complete all as specified and directed.

Dismantling wall and ceiling board (fibre, pulp, insulation etc) or insulation board/slab/blanket, any thickness including cover fillets complete all as specified and directed.

M&L for Powder coated galvanised iron snap grid frame work of size 600 x 600 mm for false ceiling comprising of Main runner 'T' section of size 38mm x 24mm x 0.40mm thickness, Cross 'T' of size 29mm x 24mm x 0.3mm thickness and wall angle of size 24mm x 24mm x 0.43mm thick suspended with 4mm dia GI wire from purlin @ 1.20m c/c and fixed with 4mm thick designer ceiling boards complete all as specified and directed.

Taking down aluminium door frame including shutter of any description exc 1.5 sqm but n.exc 4 sqm each and removing from site complete all as specified and directed.

Taking down aluminium window/ventilator frame including shutter of any description n. exc 1.5 Sqm each and removing from site.

M&L for powder coated anodised aluminium frame for doors, windows, window shutter ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

M&L for powder coated anodised aluminium door shutter, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws, 5.5mm thick glass etc complete all as specified and directed.

M&L Powder coated aluminium window shutters, side hung type without sash bars, aluminium sections weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fitting such as peg stays 150mm long (1 no) hinges type B-21 100mm long (2 no) suitable handle (1 no) complete all as specified and directed.

M&L Figured glass 4.0 mm thick pin headed type and glazing wth oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and directed.

S&F in repair Mild steel Butt hinges, medium weight, cold rolled of size 100 mm complete all as specified and directed.

S&F in repair aluminium anodised barrel tower bolts of extruded section 150 mm and fixed complete all as specified and directed.

S&F in repair Extruded aluminium handles fabricated type anodised 150mm long complete all as specified and directed.

S & F in repair for aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections (250 mm length) complete all as specified and directed.

Taking down chowkhat or frame with shutter (without taking off shutter from the frame) area not exc 1.5 Sqm each and removing from the site including making good the disturbed surfaces of wall etc to match with existing adjoining surfaces complete all as specified and directed.

All as per item No.20 but area exc 1.5 Sqm and not exc 4 Sqm each complete all as specified and directed.

Taking down shutter of any description exc 1.00 sqm each but n.exc 2.00 Sqm complete all as specified and directed.

M&L 2nd class hard wood (SAL) plain solid straight chowkhat or frame, wrought, framed, rebated on the solid, put together with glue and pinned at joint complete all as specified and directed.

M&L 2nd class hard wood 35 mm thick factory made plain framed panelled shutter (any number of panels) with panels of timber flat on both sides (feather edged),or of veneered particle board medium density, wood particle board with commercial face veneers fitted to chowkats with rail and stile as per IS-1003(part-1) klin seasoned and chemically pressure treated complete all as specified and directed.

M&L 30mm thick flush shutter, factory made, solid core construction with particle board core and ply wood face panels, commercial type on both sides and fitted to chowkats complete all as specified and as directed.

M&L 2nd class hard wood 30 mm thick glazed and Skelton shutter open rebated factory made and prepared to receive glass / gauge etc, edges of framing plain, chamfered or rounded and fitted with cut and mitred beads for securing gauge, size of members as per SSR Part - I section clause 8.20 (a) complete all as specified and directed.

M&L Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement supplying & fixing in the frame at site complete all as specified and directed.

M&L Solid PVC door frames of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying & fixing in opening complete all as specified and directed.

M&L Mild steel hold fast made of flat iron conforming to Fe-290 Gde E-165 of size 25 x 3 mm bent to shape required with splitting end and drilling holes for fixing nuts & bolts (including nuts & bolts) including treating the steel surfaces with tar or coal tar black paint and sanding neatly newly tarred surfaces with clean sharp sand all complete all as specified and directed.

S&F 2nd class hard wood door / window cleat and stoper, article n. exc 200 cum each complete all as specified and directed.

S&F aluminium anodised barrel tower bolt 125 mm complete all as specified and directed.

All as per item no 31 but 200 mm long complete all as specified and directed.

S&F 250 mm long Aluminum alloy anodised, sliding door bolt with hasp and staple(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy complete all as specified and directed.

Supply & Fix Mild steel Butt hinges, medium weight, cold rolled of size 75mm complete all as specified and directed.

All as per item No.34 but 100 mm size complete all as specified and directed.

S&F 300 mm MS ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and directed.

S&F in repair 300 mm MS ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and directed.

S&F 100 mm aluminium alloy handle anodised fabricated type complete all as specified and directed.

All as per item No.38 but 150 mm complete all as specified and directed.

S&F for floor door stopper of brass body and tongue with hard drawn steel spring (overall length of cover plate 140mm) complete all as specified and directed.

M&L in repair galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm fixed with tinned tacks/ wire staple / fitted with beads complete all as specified and directed.

M&L galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm fixed with tinned tacks/ wire staple / fitted with beads complete all as specified and directed.

Hacking out old broken glass any thickness or size from wooden or matle frames glazed with putty or beads complete all as specified and directed.

M&L Plain sheet glass pane, 3 mm thick, ordinary quality and glazing with oil putty or beads in square not exc. 0.5 Sqm each pane complete all as specified and directed.

M&L for Preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel painting over a coat of pink primer complete all as specified and directed.

Taking down cement plaster from wall including raking out joints hacking for key and scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15mm thick cement plaster in cement mortar (1:6) on fair faces of brick work or concrete surfaces, finished even and fair complete all as specified and directed.

Preparation of new plastered or un plastered surfaces of walls including cornices, pilasters etc and applying two coats of Oil bound distemper over a coat of alkali resistant white cement primer complete all as specified and directed.

Taking up or down old rusted steel tubing 15 mm bore with all fittings, concealed type including connection from wall/floor ceiling and separating serviceable pipes and setting aside for reuse all complete all as specified and directed.

All as per item No.49 above, but 20 mm bore complete all as specified and directed.

M&L 15mm bore Unplasticiscd PVC pipes of pressure rating 10 kgf/Sq cm fixed to wall or ceiling or laid in floors incl fittings etc complete all as specified and directed.

M&L 20mm bore Unplasticiscd PVC pipes of pressure rating 10 kgf/Sq cm fixed to wall or ceiling or laid in floors incl fittings etc complete all as specified and directed.

Supply and fixed in repair Vitreous china wash down water closet pan (pedestal pattern), floor mounted white with all fittings including fixing bolts, but excluding flushing cistern and flush pipe with and including plastic water closet seat, white, closed pattern with flat bottom and cover and mild steel / CP / aluminium / hinging device complete with including ‘P’ or ‘S’ trap complete all as specified and directed.

Supply and fixed in repair PVC low level flushing cistern, white, 10 litre capacity, symphonic action type, white body with inlet, ball valve, float , handle, bracket, 32mm bore steel chromium plated flush pipe etc and connecting to WC and water pipe lines complete all as specified and directed.

Supply and fixed in repair Vitreous china wash hand basin, flat back, white of size 630x450mm including cutting for and pinning in ends of brackets with and including brackets and 32mm bore 1.50m long DPE waste pipe complete all as specified and directed.

Supply and fixed in repair Rotational moulded polyethylene water storage tank,500 litres capacity, ISI marked, multilayer constriction (cylindrical vertical with closed top), hoisted & fixed in position including dismantling water tank and removing to store complete all as specified and directed.

Supply and fixed in repair Rotational moulded polyethylene water storage tank,1000 litres capacity, ISI marked, multi layer constriction (cylindrical vertical with closed top), hoisted & fixed in position including dismantling water tank and removing to store complete all as specified and directed.

Supply and fixed in repair Ball brass valves, high pressure, with polyethene float and fly nut complete, screwed for GI pipe or brass ferrule of 20 mm bore complete all as specified and directed.

Supply and fixed in repair 15mm bore Bib tap chromium plated (Long Body), with wall flange, screwed down, screwed for GI pipe or brass ferrule complete all as specified and directed.

Supply and fixed in repair 15mm bore Pillar tap, long neck cast copper alloy with capstan head, chromium plated, screwed down, high pressure with long screwed shanks, fly-nuts, with screwed for 15mm bore GI pipe complete all as specified and directed.

Supply and fixed in repair PTMT Grating doom 125 mm dia with waste hole of having minimum weight 40gms complete all as specified and directed.

Supply and fixed in repair Towel rail, 600mm long chromium plated fixed with and including chromium plated brass screws with wooden plugs complete all as specified and directed.

Supply and fixed in repair Soap dish brass chromium plated fixed with and including chromium plated brass screws with wooden plugs complete all as specified and directed.

Supply and fixed in repair 15 mm bore Angular Stop cocks, chromium plated (concealed type), screwed down, high pressure, screwed both ends for 15mm bore GI pipe or for union complete all as specified and directed.

Supply and fixed in repair Waste fittings, 32mm bore, brass ,chromium plated for glazed ware sink or basin with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed with 32mm bore PVC low density polyethylene waste pipe complete all as specified and directed.

Supply and fixed in repair 15 mm dia PVC connection pipes of 450 mm long with PTMT nut at both ends complete all as specified and directed.

Supply and fixed in repair Chromium plated shower roses 125 mm with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.

Demolition of brickwork/stone masonry built in cm including all quoins ,arches , pillars, etc, but excluding ashlar facings ,dressed stonework and precast concrete articles complete all as specified and directed.

M & L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M & L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in 1:4 complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for Screed bed or bedding layer of cement mortar CM (1:4) 15mm thick for laying floor finishes complete all as specified and directed.

M&L for Vitrified Ceramic tiles 8-9 mm thick (square/ rectangular) polished light shade , area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for Vitrified Ceramic tiles light shade 8-9 mm thick area of each tiles not exc 0.36 Sqm, in skirting / vertical surface laid over and including 10mm thick rendering in CM 1:4 etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L glazed ceramic coloured tiles (352x250x7mm/450x300x7mm ) thick set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles in vertical surfaces such as skirting dados etc including over 10 mm thick cement plaster in CM 1:4 complete all as specified and directed.

M&L non skid coloured ceramic tiles 7-8mm thick (square or rectangular) area of each tiles exc 0.11 Sqm but n.exc 0.18 Sqm in floors set jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M & L for preparation of old plastered surfaces of any description on walls including brooming down or steel wire brushings, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oils and greasy spots and applying one coat of white wash on wall complete all as specified and directed.

All as per item No.78 above, but on ceilings complete all as specified and directed.

M & L for preparation of old plastered surfaces of any description on walls including brooming down or steel wire brushings, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oils and greasy spots and applying one coat of Oil bound distemper complete all as specified and directed.

M&L for preparation of old painted steel or iron surfaces as of any description over 10 cm in width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old painted wooden or wooden based surfaces of any description of following width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new painted steel or iron surfaces as of any description over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L for 19mm dia stainless steel decorative curtain rod fixing to all opening and joineries portion complete all as specified and directed.

M&L for stainless steel bracket with end holders complete all as specified and directed.

Demolition of (Un reinforced) Cement Concrete in ground floors and pavings n.exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for 75 mm thick PCC (1:4:8) type D2 using 40 mm graded stone aggregate as in sub base etc complete all as specified and directed.

M&L for designed, pre polished chequered cement concrete tiles 25mm thick with grey cement and pigments set, jointed & pointed in neat cement slurry, laid over 20mm thick screed bed in CM 1:6 finished with pigments match the shade of tiles complete all as specified and directed.

M & L for sand cushioning to receive interlocking tiles incl spreading, levelling in layers complete all as specified and directed.

M & L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade With Grey Cement and pigment complete all as specified and directed.

Demolition of cement concrete of any description and in any position etc complete all as specified and directed.

M&L for Cement concrete (1:2:4) type B1 using 20mm graded aggregate as in surface channels and drains complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement complete all as specified and directed.

M&L for PCC (1:2:4) type B1 (using 20mm graded stone aggregate) as in coping, kerbs etc complete all as specified and directed.

Demolition of brick work/ stone masonry built in cement mortar including arches, pillars etc and excluding precast concrete article complete all as specified and directed.

M &L for Brickwork with subclass ‘B’ old size bricks, straight or curved on plan exc 6m mean radius built in 1:6 complete all as specified and directed.

M & L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in built in cement mortar 1:4 complete all as specified and directed.

Taking down cement plaster from brick or concrete or stone walls including racking out joints, hacking for key and scrubbing down with water etc complete all as specified and directed.

M&L 10mm thick rendering on other than fair faces of brick work or concrete surface built in cement mortar 1:6 surface finished even and fair with using extra cement complete all as specified and directed.

Demolition of RCC of any description and in any position not otherwise specifically provided for etc complete all as specified and directed.

M&L for precast cement concrete (1:2:4) type B-1 (20mm graded aggregate) in cover slab for drain etc and placing in position etc complete all as specified and directed.

M&L for TMT bars 10mm dia and over cut to length, bent to shape required including cranking bending, spirally for hoping for columns, hooking ends and binding with and including mild steel wire not less than 0.9 mm dia, complete all as specified and directed.

Dismantling posts or struts ( steel or RCC) any section including taking out embedded portion in concrete, brick work, masonry etc and making good disturbed ground to match with the existing surface complete all as specified and directed.

Dismantling of fencing wire mesh of any description complete all as specified and directed.

Excavating in post holes (or similar holes ) in soft/loose soil each not exceeding 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm , watering, and removing surplus soil to a distance n.exc 50m and making good surface complete all as specified and directed.

M&L cement concrete type B1, (1:2:4) (Using 20mm graded aggregate) in foundation, filling and mass concrete complete all as specified and directed.

M & L for Framed brackets of angles or tees with web and flanges cut to shape, drilled and counter sunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 (Brackets over 10 kg each to be measured under 'Structural Steel') complete all as specified and directed.

Supply only Steel round bar 10 mm dia and over for tying chain link fencing etc complete all as specified and directed.

Supply only chain link fencing MS galvanised fencing , any size or type including line wires, any mesh, size and type of standard rails straining bolts, etc. including provision of binding wire complete all as specified and directed. (Note- fixing measured separately)

Fixing only chain link fencing including line wires, any mesh, size and type of standards, rail, straining bolts, etc. including provision of binding wire complete all as specified and directed.

M&L screw bolts (machine made) with hexagonal or square head at one end and rounded the other or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 5 cm but n.exc 10 cm and dia of shank 11 to 15mm and fixed in position complete all as specified and directed.

M&L in repair Galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. complete all as specified and directed. (each line wire to be measured)

Supply and laying concertina coils made up of hard drawn steel wire fabric with 14mm blade clips 05 Nos in each spiral, tape thickness 0.50mm, GI stripping core wire 2.60mm thick and spiral turns per roll is 52 Nos including securing with Y shaped angle iron with available size complete all as specified and directed. NOTE :- One Roll of concertina coil should extend upto 10RM.

M&L for preparation of new untreated steel surfaces as of any description over 10 cm in width or girth not otherwise described and applying two coat of synthetic enamel paint overa coat of red oxide complete all as specified and directed.

M&L preparation of previously untreated surface of steel n.exc 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed.

M&L for preparation of old painted steel or iron surfaces as of any description over 10 cm in width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M&L Framed work such as grills, grating etc. with ends of bars shouldered and/or riveted or forged or spikes, framed, guard bars, barred iron doors, ladders, framed including pintle hinges, stops, hand-made sliding bolts, etc. conforming to FE-290 (Gde E-165) complete all as specified and directed.

Taking down carefully copper/aluminium point wiring complete (light, fan, plug point & power complete alongwith fittings (switches, ceiling roses, tube light fittings, bulk head fitting regulator, sockets , removing materials to store and offering credit & making good of disturb surfaces of wall/floors etc complete all as specified and directed.

M& L for Point wiring with 1.5 Sqmm (22/0.30mm) PVC insulated and unsheathed multi stranded copper conductor cable, 1100 volts grade, ISI marked, FRLS type drawn through and including PVC concealed conduit (ISI marked) of adequate size and its accessories with sunk cast iron/pressed steel terminal boxes of size 1.6mm thick, with 3mm thick plastic laminated sheet cover of adequate size for one light or one fan point controlled by one switch incl 1.5 Sqmm (nominal area) copper conductor cable (multistrand), FRLS type, PVC insulated and unsheathed with colour code earth wire connected to common earth dolly at one end and metallic bodies of luminaires/ fan at other end complete as per site requirement and complete all as specified and directed for the following:- (a) One light point or one fan point controlled by one switch with cables 1.5 sq. mm size Note:- Unit rate include for cutting chases for conduits and sinking for boxes and making good to wall, floors etc.

All as per ser item No. 120 above, but for One 5 Amp 5 pin socket outlet point on same board with other switches including earth wire complete all as specified and directed.

All as per ser item No. 120 herein before, but for One 5 Amp 5 pin socket outlet point on independent board.

All as per ser item No. 120 here in before but with 4.0 Sqmm (36/0.30mm) PVC copper stranded cable FRLS type for one 15 Amp 5 pin socket outlet point including PVC cable 4 Sqmm FRLS type copper stranded conductor as earth wire as specified & connected to common earth & earth terminals including boards for mounting purposes.

All as per ser item No. 120 herein before, but one light point controlled by 2 way switches complete all as specified and directed.

All as per ser item No. 120 here in before but one bell/buzzer point controlled by one push button on the same board with other switches or independent complete all as specified and directed.

M & L for Point wiring with 1.5 Sqmm (22/0.30mm) PVC insulated and unsheathed multistranded copper conductor cable, 1100 volts grade, ISI marked, FR type drawn through and including PVC casing caping/ PVC Conduit (ISI marked) and its accessories such as Tee, elbow, jointer, elbow corner etc. fixed on surface of walls, coloumns/ beams alongwith 1.5 Sqmm (nominal area) copper conductor cable (multistranded) PVC insulated and unsheathed as earth wire connected to common earth dolly at one end and metalic bodies of luminaire/ fan at other end including PVC folding boards with sunmica top for mounting switches, sockets, fan Regulators, accessories etc as per site requirement and complete all as specified and directed for the following:- (a) One light point or one fan point controlled by one switch with cables 1.5 sq. mm size.

All as per ser item No. 126 above but for One 5 Amp 5 pin socket outlet point on same board with other switches including earth wire complete all as specified and directed.

All as per ser item No. 126 here in before but for One 5 Amp 5 pin socket outlet point on independent board complete all as specified and directed.

All as per ser item No. 126 here in before but with 4.0 Sqmm (36/0.30mm) PVC copper stranded cable FRLS type for one 15 Amp 5 pin socket outlet point including PVC cable 4 Sqmm FRLS type copper stranded conductor as earth wire as specified & connected to common earth & earth terminals including boards for mounting purposes complete all as specified and directed.

All as per ser item No. 126 above here in before but one bell/buzzer point controlled by one push button on the same board with other switches or independent complete all as specified and directed.

All as per ser item No. 126 here in before but one light point controlled by 2 way switches complete all as specified and directed.

Supply and Fixing bell push, flush type, 5 Amp single pole, 230 volts white finish all as specified & directed.

Supply and fixing switch piano flush button 5 Amp single pole 2 way 230 volts white finish complete all as specified and directed.

Supply and fixing in replacement switch piano flush button 5 Amp single pole one way 230 volts white finish complete all as specified and directed.

Supply and fixing in replacement of socket outlet flush type 5 pin 5 Amp multipurpose 230 volts single pole one way suitable for 3 pin/2pin 5 Amp plug top white/ivory finish complete all as specified and directed.

Supply and fixing in replacement switch socket combination flush type 5 pin 5 Amp multipurpose 230 volts single pole one way suitable for 3 pin/2pin 5 Amp plug top white/ivory finish complete all as specified and directed.

Supply and fixing in replacement of switch socket combination multipurpose flush type 2 in 1 type (3 and 5 pin) 5/15 Amps, 230V, AC complete all as specified and directed.

Supply and fixing in replacement ceiling rose surface PVC 50mm dia 3 terminals including PVC mounting block white/ivory finish complete all as specified and directed.

Supply and Fixing in replacement Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fitting complete all as specified and directed.

Supply & fixing in replacement stepped type electronic fan regulator Socket type on the existing phenolic laminated sheet etc. as reqd complete all as specified and directed.

Supply & fixing in replacement exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers complete as per site requirement and complete all as specified and directed.

Taking down carefully copper/aluminium sub main wiring complete alongwith complete all as specified and directed.

M&L of submain wiring with two single core PVC insulated unsheathed, multistranded flexible copper conductor 1100Volts grade, FRLS type, cables 6 Sqmm drawn through in and including rigid PVC heavy duty concealed conduits including 6 Sqmm 1100Volts grade, FRLS type, PVC insulated unsheathed multi stranded flexible copper conductor cable as continuous earth wire and connecting to common earth terminals complete all as specified and directed. Note:- (i) Two runs of cables and one run of continuous earting cable drawn in conduit/ casing and caping will be measured as one length of sub main with colour code Red Black and Green. (ii) PVC conduit / casing caping and its accessories is deem to be included in this item rates. (iii) Unit rate include for cutting chases for conduits and sinking for boxes and making good to wall, floors etc.

Taking down carefully DB/ Sheet Metal Enclosure with existing MCBs complete & making good of disturb surfaces of wall/floors etc complete all as specified and directed.

Supply and fixing distribution board sheet metal enclosure double door shutter type factory made fixed flush with wall or outside on wall surface suitable for mounting isolators & MCB's 240volts, 200 Amp rated bus bar with front openable cover suitable for SP & N 4 ways complete all as specified and directed.

Supply and fixing distribution board sheet metal enclosure double door shutter type factory made fixed flush with wall or outside on wall surface suitable for mounting isolators & MCB's 240volts, 200 Amp rated bus bar with front openable cover suitable for SP & N 8 ways complete all as specified and directed.

Supply and Fixing in replacement MCB SP 5 to 32 Amp rating 240V, 10KA 'C' curve complete with connection testing and commissioning complete all as specified and directed.

Supply and Fixing in replacement MCB SPN 32 Amp rating 240V, 10KA 'C' curve complete with connection testing and commissioning complete all as specified and directed.

Supply and Fixing in replacement MCB SPN 40 to 63 Amp rating 240V, 10KA 'C' curve complete with connection testing and commissioning complete all as specified and directed.

Supply and Fixing in replacement of MCB TP 25 to 63 Amps, 415 Volts, 50 Hz with 10 KA 'C' curve complete with connection testing and commissioning complete all as specified and directed.

Supply and Fixing in replacement of MCB TPN 16 to 32 Amps, 415 Volts, 50 Hz with 10 KA 'C' curve complete with connection testing and commissioning complete all as specified and directed.

Supply and Fixing in replacement of MCB TPN 40 to 100 Amps, 415 Volts, 50 Hz with 10 KA 'C' curve complete with connection testing and commissioning complete all as specified and directed.

Material & Labour in replacement of Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thickness buried directly in ground (earth pit not less than 2.25mtr deep below normal ground level) with top edge of earth plate not less than 1.5 mtr below normal ground level connected to and incl galvanised earth lead wire of 4.00mm dia by means of nuts & bolts, check nuts and washers of galvanised incl PCC pit of 1:2:4 type B-1, cover reinforced with XPM weight not less than 4 Kg/Sqm and 6mm dia bar handle, earth pit angle iron frame of size 25mm x 25mm, excavation and earth work in any type of soil, charcoal dust, salt, light grade GI watering pipe 20mm dia with funnel and wire -mesh and medium grade GI protection pipe of 15mm bore from top edge of earth plate upto main distribution board complete all to as shown in electrical plate No 3 of MES Sch 2009 (Part I) connected main switch board all as specified and testing on completion.

NOTES :- 1. The amount of schedule of credit shall be deducted from the total of this BOQ for arriving at contract sum.

UNISON CONSTRUCTION (BID ID -3390782)

NIRANJAN SARKAR (BID ID -3389642)

SHRI P P SHARMA (BID ID -3390742)

M/s Chakraborty Enterprise (BID ID -3390948)

M/S ALPHA BETA CONSTRUCTION (BID ID -3390582)

MESSERS D S ENTERPRISE (BID ID -3390960)

SUNIL DAS AND CO (BID ID -3390852)