Electrical works to be carried out at WSS GCET Safapora

Amount

Supply, Installation, Testing & Commissioning of MCCB 250A, 4-pole, 3-phase 415 ± 15% volts, Frequency: 50± 3% C/S current 50 KA breaking capacity. The MCCB shall be housed in a panel fabricated out of 14SW, duly given two coats of grey colour powder coating, the door of the panel shall have a locking arrangement. The panel shall be installed as per the direction of the site Engineer. The acceptable makes are Reputed Make.

Providing and fitting of 120 sq.mm Single-core XLPEInsulated,PVCInner-sheathed unarmoured LT aluminium conductor, 1100 volt/650 V, grade as per IS 7098-I (1988) from HT transformer to Bas-bar and Panel.The job also includes termination of ends of cable with suitable rating of Al. thimbles duly tapedas per site requirement along with suitable Nylon Ties for tying cables together. Make Reputed Make

Providing and Fitting of 3-core multi-stranded copper cable, PVC insulated, internal intermediate sheathed of 16mm Sq. Submersible flat cable conforming to IS: 694 (Part 1st) – 1964 & IS: 694 (Part 2nd) – 1964 of Reputed Make make for submersible pumping equipment & for inter connections of electrical gadgets. The job also includes termination of ends of cable with suitable rating of Cu. thimbles duly taped.

Supply, Installation, Testing & Commissioning 25mm Sq. Single Coreflexiblecopper power cable, suitable for LV 1.1KV/650V grade,XLPE Insulated, cores laid up, PVC inner sheathed, Un-armoured for connecting Control panelsand Voltage Stabilizers together.Confirming to IS7098- Part 1, 1988. Acceptable makes for the cable are Reputed Make. The job is inclusive of Providing & fixing of copper thimbles (not less than 40 No’s) (make Dowels)for the cableas per site requirement duly crimped with the cable termination ends by crimping tool and 150mm Nylon Cable ties (150 No’s). The cable is used to connect various electric gadgets.

Providing and fitting of flexible canvas conduit for 25Sqmm single-core PVC XLPE unarmoured LT copper conductor from Panel to voltage stabilizer.

Providing and erection of 9M long Hot Dip galvanized Octagonal pole of (Single section) with bottom 200mm, top 90mm wide, thickness 3mm with 70 Microns Zinc coating having inside arrangement for providing of power connection along with following items. 1. 03 No. Terminal Connector 20A. 2. 04 No. MCB DP 10A. The job shall include fabrication, providing and fitting of three arm GI structure at the top having 120° angle between arms and each arm having 15° inclination with respect to horizontal plane. Each arm should be of 2ft lengthy and size and shape appropriate as per requirement of the Luminary. The job also includes providing and fitting of required length of flexible multi-strand 1.5mm copper wire from each terminal connector to each holding arm. The pole shall be mounted on 1:2:4 cement concreting of size not less than 2ft x 2ft x 4ft using 04 No. anchor bolts of required size not less than 7 inch in length. The job also includes providing, fitting, installation & testing of 1KW AVR of reputed make for maintaining of proper voltage for the lights to be enclosed in a steel box. The MCB’s should be enclosed in a glazed door type DB as per site requirement to be provided/fitted by the firm. The complete job shall include Earthing in GI Electrode, PVC pipe HDPE of required size & length for inlet and outlet for cable in connection block. Acceptable makes are Reputed Make.

Providing. Installation, testing and commissioning of 120 Watt LED (Street Light Type) Input; 90-240 V, 50 Hz. Power factor; >0.9 Colour Temperature: 4K – 6.5K Beam angle: 120°- 170° Lumens: >12000 Operating Temperature: -20° to 60° The LED shall have pressure die cast aluminium housing with power coated finish and having Ingress Protection upto IP-68. The LED shall be properly fitted on the arm of the pole and connected to the copper wire as provided in item above and made functional. Make: Reputed Make

Providing Laying and connection of 2Cx6mm², PVC sheathed Aluminium, Armoured Cable from the connecting of high mast pole to the stabilizer. The job includes underground laying or overhanging through PVC conduit as per requirement and directions of the site incharge. Make: Reputed Make.

Providing, laying & fixing with adhesive/bonding material of insulation rubber mats on the floor of the pump house, covering area around electro-mechanical machinery for safeguarding the life & limb of the workmen due to possible leakage of current & short circuit. The floor surface shall be made good & shall be free from dust, grease, foreign material & moisture free. The mats shall be as per IS 15652:2006 & shall have the following specifications: - Composition: Rubber (synthetic mats for electrical purpose) Thickness: - 2.5mm Size: - 1M wide. Make:- Reputed Make The rubber mats shall be accepted with manufacturers test certificate.

Providing of solar/ electrical lantern chargeable on both solar & electrical 220v supply. (Reputed Make).

Providing of bamboo ladders 18 feet long along with 15 feet long Link rods and HT Glove pair.

Supply, installation, Testing & commissioning of 1000VA Full Sine wave power inverter (Make: Reputed Make) including Providing / Installation of 12V, 180AH Tubular inverter Battery with trolley and cover. (Make: Amaron /Exide) with 2-core 6mm2 Cu wiring as per site requirement along with other accessories like SS-Combine (02 No’s), 3-pin plugs etc of reputed make for proper fitment and installation of the item.

Providing & Fitting of 1200mm sweep Reputed Make make ceiling fan with 1.5mm2 Cu wiring as per site requirement complete in all respects like hook for holding the fan, tape, fan dimmer switch etc. Preferred colour is Dark Brown.

P/I of Chemical earthing for complete earthing of various Electrical Gadgets comprising of company fabricated earthling electrode as per IS: 3043. The job includes Auguring of bore of required dia/depth for installation of electrode along with backfill compound mixed with soil and all other items required thereof for achieving the best result. The job includes providing &connecting of various Electrical Gadgets through GI strip with the earthling electrode as per site requirement and making of surface structure in brick/cement concrete material with proper main-hole cover as per present IEEE rules. Safe earthling electrode size = 80mm dia. Length = 2000mm Back fill compound = 25 kg make– JVM -393, Ashlok, Recons, True Power.

M/s Shaheen Enterprises

M/S Ganie Electricals

M/S MIR ELECTRICALS and MECHANICAL ENG WORKS

ASIF ENGINEERING WORKS AZAD GUNJ BARAMULLA