PERIODICAL MAINT TO DGRR MESS AND OFFICE AT RPSO COMPLEX, ARTY MESS AND OTHER MESSES AND CENTRAL AMENITIES IN THE AOR OF AGE B/R-I UNDER GE (EAST) DELHI CANTT-10

Amount

M & L for Brick work with sub class 'B' bricks of old size, straight or curved on plan to any radius built in CM 1:6 including demolition of Brickwork built in cement mortar including all quoins, arches, pillars etc. complete all as specified.

Taking down cement or cement lime plaster, any description on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and as directed.

M & L for 15mm thick rendering in cement mortar 1:4 on fair face of brick walls/ concrete surfaces and finished even and fair incl scaffolding etc, complete all as specified and as directed.

M & L for 12mm thick rendering in cement mortar 1:6 on fair face of brick walls/ concrete surfaces & finished even and fair incl scaffolding etc, complete all as specified.

M & L for 5mm thick rendering in cement mortar 1:3 on ceiling, finished even and fair incl scaffolding etc, complete all as specified.

M & L for 75 mm thick cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection laid in bays & surfaces finished even and smooth without using extra cement including demolition of cement concrete (unreinforced) in ground floor or in any position and paving not exc. 15 cm thick (below or above ground level) complete all as specified and as directed.

M & L for Non-Skid coloured ceramic tiles 7-8mm thick (square/rectangular) of size 300mmx300mm or 400mmx400mm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 15mm thick screed bed in CM 1:6, with dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), complete.

M & L for glazed ceramic tiles in vertical surface of size 300mmx450mm or 300mmx600mm and 7-8 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 10mm thick rendering in CM 1:4 after dismantling floor, hearth or wall tiling with cement mortar bedding (but not backing), complete all as specified and as directed.

M & L for 16-18 mm thick granite of any type work table rubbed and polished as in steps, jambs, pillars, window cills, cooking platforms and like in over and incl 15mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite slab, notching and moulding and dismantling of existing granite complete all as specified and as directed .

M & L for Vitrified coloured tiles dark shade 8-10mm thick (square/rectangular) polished, area of each tile exc 0.42 sqm but not exc 1.00 sqm each in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6, after dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 Sqm each including iron mangory complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.5 sqm but not exc 4 sqm each including iron mangory complete all as specified and as directed.

S & F for Powder coated aluminium partition with frame of standard powder coated aluminium sections of size 101.60mm x 44.45mm x 2mm in vertical and horizontal members and glazed with 5mm thick tinted glass and 12mm thick pre-laminated particle board interior grade with laminations on both faces according to site requirement including jointing cleats, glazing pins, rubber packing and fixing accessories as per site requirement including dismantling of existing partition of any type complete.

S & F plain gypsum board panel 12 mm thick on false ceiling (including any design/ cob design as required & pattern as approved by GE) with and including necessary GI frame work for seamless ceiling used with 'T' , channel or any section including screws , cleats ,fasteners, clips and all required accessories , hangers etc. of galvanized steel all as per manufacturer design conforming to IS-2095 and 2542(1981) the weight of the board shall be not less than 7 kg per sqm and including two coat of OBD over a coat of putty including dismantling of walls and celling existing old board (fibre pulp. Insulation etc.)or insulation boards/slabs/blanks any thickness including cover fillets etc. complete all as specified and directed.

M&L 4mm thick designer board false ceiling e- board ( Make : Everest or equivalent as approved by GE) in ceiling fixed with screw as per manufactures instruction, fixed with white powder coated galvanized iron grid with 24mm wide T-section exposed flanges comprising of main runner made from 0.33 mm thick galvanized steel sheet & size T-24x32 mm and spaced at 1.2m c/c securely fixed to the structural soffits by hangers at 1.2m of GI wire 2 mm dia fixed rawl plug, level adjusters and screws etc. The last hanger at the end of each main runner shall not be greater than 450mm from adjacent wall flush fitting of 1200mm long cross tee with (double stitching) to be inter locked between main runner at 600 mm c/c to from 600 x 600 mm modules, angle along perimeter wall shall be of 0.45mm thick galvanized steel of size 19 x19 mm of white colour all as per instruction and including dismantling of walls and celling existing old board (fibre pulp. Insulation etc.)or insulation boards/slabs/blanks any thickness including cover fillets , any type of frame etc. complete all as specified and directed.

S & F in repairs Vitreous china single Piece floor mounted WC With PP Soft Close Seat Cover, Hinges, with cistern & Dual Flush Cistern Fitting, Fixing Accessories and Accessories Set, Size: 360x730x740 mm, S Trap- 300 mm including connection to drain pipe with all fitting and fixture complete all as specified and as directed. Make & Cat Part : Jaquar-Cat No. SLS-WHT-6851S300PP or equivalent in Marc / Kohler)

S & F in repairs 15mm Angle valve of CP any colour high pressure screwed for iron pipe and fixed, complete all as specified and as directed. (Make: Jaquar/Marc/Kohler)

S & F in repairs 15mm Stop valve/ angle valve of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms/ 20mm- 92gms)

S & F in repairs Two way Angle valve 15mm bore dia or pipe, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and as directed. (Make: Jaquar/Marc/Kohler)

S & F in repairs ready made floor/wall mounted Vanity box made of HDHMR board, both side laminated consisting of the following combination :- (a) Wash Hand Basin 810mm x 500mm. (b) Base Cabinet 780mm x 485mm x 460mm. (c) Side Cabinet 300mm x 250mm x 1800mm. Make : Hindware - Cat Part No. 70089 or 70084/ Make : Kohler : Cat Part No. K-31602IN-E63 or equivalent.

S&F in repair Brass CP basin mixer central hole , for mixing hot and cold water fixed as per manufacture's manual, with long shank and cup washers, screwed both ends suitable for 15mm bore GI pipe joints to GI pipes or unions complete all as specified and directed (Make : Jaquar/Marc/Kohler).

S & F in repair Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and as directed. (Make: Jaquar/Marc/Kohler)

S&F in repair Brass chromium plated towel rack of size 600 mm x 350mm, fixed with brass screws, fixed in repairs, complete all as specified and as directed. (Make: Jaquar/Marc/Kohler)

S&F in repair 32 mm bore PVC waste pipe with fittings of approved make suitable for WHB, Urinals and Sink etc. all as specified and directed.

S & F in repair Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf walls or including fixing cantilever brackets and connecting union to pipe overall size 915mmx460mm bowl size 410mmx330mmx 160mm all as specified and directed.

S & F in repair Fancy type sink mixer for mixing hot and cold water with swinging port, screwed for iron pipe,15mm bore complete all as specified and as directed. (Make : Jaquar/Marc/Kohler)

S & F in repair Designer type high quality fancy type looking mirror of size exc 1.00 Sqm but not exc 1.5 sqm as approved by Engr-in-Charge 8-10mm thick, fixed to wall with stainless steel studs, screws, brackets and washers etc complete all as specified and as directed.

S & F Rotational moulded polyethylene water storage tanks 1000 lts capacity, (ISI marked) double layered (cylindrical vertical with closed top) hoisted and fixed in position including 20 mm dia PTMT ball valves, high pressure, with polythene float and flynut, tank nipple of suitable size complete, screwed for iron pipe or brass ferrule and fixed including taking out existing unserviceable overhead tank of any description complete.

Description all as per srl item No 30 here-in-before but of 500 ltr capacity.

S & F factory made WPC railing combining WPC board/Fancy designer type grating and WPC frame 100% solid WPC (wood polymer composite) railing of required length and of 2' to 2.5' height , comprising of virgin PVC resin of K value 58-60 (Suspension Grade) , Calcium Carbonate and natural fibres (Wood Powders/rice husk//wheat husk) and non toxic additives, made from single extrusion process, 18mm thick WPC foam board with having minimum density 650kg/cbm and WPC frame having minimum density 780kg/cbm manufactured by "RAJSHRI" an ISO 9001-2015 certified Company, having good screw holding capacity (screw withdrawal strength of 2000N (Face) & 1100N (Edge) , Minimum comprising of 50N/mm2, Modules of elasticity 850N/mm2 and resistance of speed of flame of class A category with property of being termite/Borer free water /Moisture proof and fire resistance. For WPC railing WPC jali to be fixed with WPC frame of size 75x50mm with necessary supporting lengths at vertical as well as horizontal at wall frames to be fixed with 3"x3" GI 'L' or SS cleats to support vertical frame lengths including demolition /dismantling of existing RCC jallies with frames complete all as specified and as directed. (Make : Rajshree or equivalent as approved by GE) (Note : The said item shall be fixed over boundary walls/roof tops and in any other positions as per requirement at site)

S & F for PVC hollow wall panelling 7 to 8 mm thick wood grain teak finished pre-laminated inclusive of fixing to wall incl moulding end caps fixed with PVC sleeves and screws as required at site including taking down existing panelling of any type complete all as specified and as directed.

M & L for preparation of new plaster external wall and ceiling surfaces of and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and as directed.

Description all as per srl item No 34 here-in-before but single coat over previously treated wall or ceiling.

M & L for Preparation of newly plastered /unplaster surfaces of walls and ceilings and applying two coats of Oil Bound Distemper on wall surfaces over a coat of primer and 1.5-2mm thick wall care putty ,complete all as specified and directed.

M & L for Mild steel rolled sections Fe-410-W (Gde-E-250) quality B as in Compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc. complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

S & F painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of Plain or corrugated AC Sheet complete all as specified and as directed.

S & F painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of existing corrugated or semi corrugated AC Sheet , Nainital or similar pattern as in roof coverings complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floor or in any position and paving not exc. 15 cm thick (below or above ground level) complete all as specified and as directed.

M & L for 75mm thick Cement concrete 1:4:8 Type D-2 (using 40mm graded agg) as in sub base of flooring or in any position complete all as specified and as directed.

M & L for rubber moulded Coloured Chequered cement concrete tiles 30cm x 30cm x 20-22mm thick, set, jointed and pointed in neat cement slurry over and including 15mm thick screed bed in CM 1:6 etc including dismantling of existing chequered tiles of any type complete all as specified and as directed.

S & F for Precast RCC manhole covers 75 mm thick medium duty conforming to IS-12592 of any shape and size as per requirement at site and as directed including demolition of existing manhole covers of any type complete all as specified and as directed.

M & L for Stainless Steel work of Grade-304 as in vertical post/pole, trusses of any type and size including special shaped washers, channels, plates (horizontal/ vertical/cantilever type work) also ornamental works like designer railing chain, lattoo any type and size as approved by GE and as reqd at site made of hollow tubes or in any other shape as per requirement at site, including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary nuts and bolts dash fasteners, stainless steel bolts etc., of required size on the top of floor or the side of waist slab with suitable arrangement complete all as specified and as directed. (Note :- No extra payment shall be made to the contractor for ornamental works of this item).

S & F for 2mm thick colour coated polycarbonate roofing sheet translucent plain/corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall, gate etc including taking down old UNSV fibre sheet of any type complete all as specified and as directed.

S&F Aluminium alloy powder coated door including frame and channel of section (Door frame single groove 101.6mm x 44.45mm x 2.1mm, shutter top section 47.62mm x 44.45mm x 1.95mm thick, shutter bottom section 114.30mm x 44.45mm x 2.15mm thick, shutter vertical section 85mm x 44.45mm x 1.80mm thick, shutter middle section 83.50mm x 44.45mm x 2.40mm thick & glazing clips weighing not less than 0.097 Kg/RM) including shutter fixed to sliding type/openable frame and channel as directed and approved by GE and as per IS specifications including provn of 5.5mm thick tinted glass/12mm thick pre-laminated particle board as required including handles, tower bolt, floor spring heavy duty “SAMRAT” , locking arrangement “GODREJ”, rubber gasket and door stopper complete all as specified and as directed.

S & F Solid PVC door frame of size 50mm x 95mm made out of wood grain printed PVC sheet used reinforced with M.S. tube, supplying & fixing in opening as per specification & drawing complete all as specified and as directed.

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and as directed.

S & F Factory Made Solid PVC Moulded Door Shutters with wood free EPS, 28 to 30 mm thick (stile:), with 2,4 or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front and back Face (wooden finish pattern), supplying & fixing in frame at site as per specification & drawing complete all as specified and as directed.

S & F Factory Made Solid PVC Door Shutters, 28 to 30 mm thick (stile:), panel design with 10mm thick PVC Sheet , supplying & fixing in frame at site as per specification & drawing complete all as specified and as directed.

S & F in repair 15mm dia GI tubing medium grade with all fitting and fixed to wall and ceiling or laid in floors etc. incl scaffolding, cutting chases in wall where ever required etc complete, all as specified.

S & F in repair 20mm dia GI tubing medium grade with all fitting and fixed to wall and ceiling or laid in floors etc incl scaffolding, cutting chases in wall where ever required etc complete, all as specified.

S & F in repair bib tap fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe, 15mm dia, fancy type, cast copper alloy, chromium plated long body with flange complete. (Make: Jaquar/Marc/Kohler)

S & F in repair for 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete.

S & F 15mm bore Gun-metal, globe or gate valves, with iron wheel head screwed for iron pipe of 15 mm bore complete all as specified and directed.

S & F Vitreous China squatting pan of pattern “long pan”, size 580 mm white with ‘P’ or ‘S” trap, front or back inlet and foot rests, any pattern with connection to trap , and to flushing pipe antisyphonage pipe including trap set in and including concrete etc complete including dismantling of existing WC and making good to floor all as specified and directed.

S & F in repair Vitreous China wash down pedestal pattern EWC, white and including with PVC (SWR) ' S' Trap with connection to drain and flushing pipe antisyphonage pipe, and making good to floor complete all as specified and directed.

S & F in repair 10 Ltrs capacity PVC valveless symphonic action type flushing cistern white low level with inlet, ball valve float handle including bracket and flush pipe etc complete all as specified and directed.

S&F Vitreous China urinals, half stall type, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixed in repairs, complete all as specified.

S&F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixed in repairs, complete all as specified.

BLANK

M & L for Coloured Machine pressed precast concrete interlocking paver block of any shape and size (Two colour combination) conforming to IS 15658-2006 of 60 mm thick, M-35 Grade with grey cement and pigment laid over 50 mm thick layer of dry sand in floor/path complete all as specified and as directed.

M & L for PCC (1:2:4) Ty B-1 (using 20mm graded stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates and the like including weathering, slightly rounded or chamfered angles and throating,

S & F in repair Brass chromium plated bottle traps 40mm bore for wash basins/ sink/ urinals with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and as directed.

S & F PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and as directed.

S & F in repair 110mm dia PVC (SWR) pipes single socketed in any length with rubber rings joints fixed to walls or laid in floors as sanitary fittings, rain water pipes etc in any position complete all as specified and directed.

S & F PVC (SWR) 110mm bore bends with access door, complete all as specified and directed.

Descritpion all as item no 67 above but 75mm bore complete.

Descritpion all as item no 68 above but 75mm bore complete.

S & F Steel work in tubular poles/trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete.

S&F Aluminium alloy powder coated windows including aluminium powder coated frames sliding track, bottom weighing not less than 1.015 Kg/RM, sides and top not less than 0.826 Kg/RM double rebated and 0.55Kg/RM for window shutter with one fixed glazed shutter and two nos glazed/gauged shutter sliding type with aluminium sections as per series - A (15mm) 3 track of Jindal section numbers for sliding windows with framed shutter including aluminium allow powder coated snap type beads handles with locking arrangement spring action and glazing clip joint cleats rubber gaskets etc including provision of 5.5mm thick tinted glass/ frosted glass of superior quality and stainless steel jali including all standard fittings, complete all as specified and as directed.

M & L for preparation of plastered or unplaster old decorated surfaces of walls including brooming down or scraping down with steel wire brushes of smoke spots , moulds ,moss efflocerent salts and treading oil and greasy spots, filling the cracks, holes with POP/Putty and applying One coat of Oil bound distemper complete all as specified and directed.

M & L for preparation of plastered, unplaster or pointing surfaces old decorated/un-decorated surfaces of walls including brooming down or scraping down with steel wire brushes of smoke spots , moulds ,moss efflocerent salts and treading oil and greasy spots, filling the cracks, holes with POP/Putty and applying One coat of exterior acrylic emulsion paint of any tint all as per manufacturers instructions to achive desired finish at any height complete all as directed.

S&F 0.05mm thick sun control film having 50% visible light transmittance on glass surface of any colour / shade including preparation of surface complete all as specified and directed. Make -(3M or equivalent)

M & L for Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 grey cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern (groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove) complete including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete.

M&L for APP based polymeric membrane with mineral granules on top surface, minimum weighting 3 kg/Sqm and minimum 3 mm thick reinforced with polyester non woven fabric (wt not less than 150 gms/sqm) over one coat of 85/25 bitumen @1.2 kg/sqm with bitumen primer and paste the membrane with torching method and again apply a coat of 85/25 bitumen @ 1.6 kg/sqm at overlapping joints with a over lap of 75mm at the sides and 100 at the ends complete all as specified including taking down existing roof treatment of any description. Note: the water proofing treatment shall be carried out by the manufacturer or their authorised applicators.” Make- Asian , Stp , IWL Notes- 1. The Work Shall be executed through authorized applicator of manufacturer 2. Authorized applicator shall be approved by GE before starting of work 3. All material shall be procured directly

S & F for Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial remittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface up to 3 cuts complete, including providing skirting up to 150 mm height along the parapet walls in the same manner complete all as specified.

S&F 100mm size stainless steel butt hinges fixing with screws to door frame complete all as specified.

S&F aluminium Anodised 150mm size barrel tower bolt complete all as specified and as directed.

S&F 150mm size aluminium anodised handles complete all as specified and as directed.

S&F 100mm size Mild steel butt hinges fixing with screws to Iron door frame complete all as specified.

S&F 300 mm long stainless steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S & F floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring and vulcanised rubber piece fixed in floor, over all length of cover plate 140mm complete all as specified and directed.

S & F for 150mm long mild steel barrel tower bolts Mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed,complete all as specified and as directed.

S & F 3mm thick sheet glass, ordinary quality and glazing with wooden beading not exc 0.5 Sqm in each pane all as specified and directed including hacking out old broken glass (any thickness, size, quality or description) from wooden or steel frame glazed with putty or fixed with beads complete all as specified and directed

S & F 5.5mm thick sheet glass, ordinary quality and glazing with wooden beading exc 0.5 Sqm in each pane all as specified and directed including hacking out old broken glass (any thickness, size, quality or description) from aluminium or steel frame glazed with putty or fixed with rubber /beads complete all as specified and directed

S & F in repairs Urinal spreader of CP any colour for fixing with 15mm dia pipe complete all as specified.

S & F Galvanised mild steel wire cloth 0.63mm nominal dia of wire and average width of aperture 1.4mm and fixed to doors and widows with necessary 12mm iron flats with welding and including dismantling of old wire cloth complete all as specified and directed. (Note :- Rates are inclusive of welding and supply of flats including reqd nut bolts wherever required)

M&L for easing of UPVC door shutter including repair/replacement of hinges as required complete

S&F in repair muilty lever lock for UPVC door shutter complete all as specified and directed.

S & F in reapir flushing cistern kit of any type complete all as specified and directed

S & F in reapir flushing cistern handle complete all as specified and directed

S & F in repairs stainless steel curtain Rod 25 mm dia with holders fixed to wall with finials and bracket etc complete all as specified and as directed. (Note : Damage to Brick/stone or any type of wall and existing cement plaster/pointing during fixing of curtain rod/bracket/finial shall be make good and bring back to old position to be done by the contractor and the cost for the same shall be deemed to include in the quoted rate, No extra payment will be made for brick work, re-plastering and painting to the contractor.)

Note for Srl item No 1 to 94 :- The work caters for agaisnt this Sch /BOQ is required in piecemeal as and when requried basis over scattered area under AGE B/R-I and the contractor is requried to visit site of work with prior appointment to Engr-in-Charge to ascertain exact scope of work involved and rate quoted for items shall deemed included for these aspect and nothing extra shall be payable on account of any misunderstading later on.

Akhil Enterprises (BID ID -3495218)

M/s Shubh Enterprises (BID ID -3494936)

S GOURAV PRAKASH ENTERPRISES (BID ID -3495478)

garnet engineers contractors (BID ID -3495128)

Vipul Construction (BID ID -3497396)