Construction of Officer club and 2 Nos Type V Quarters

Amount

Section I : Demolition of existing Officer's club at Officer colony of BSPS at Surangani

Dismantling roofing including ridges, hips, valleys, gutters etc. stacking the serviceable materials and disposal of un-serviceable materials within 20 metres lead: G.I. Sheet roofing

Dismantling wood work. Wrought framed and fixed in frames other frames and trusses of span upto 10 metres and height between ridge and floor level stacking the serviceable materials and disposal of un-serviceable materials with in 20 metres lead: Sectional area average 40 sq.cm. Or over

Dismantling cement asbestos celotax/hard board in ceiling or partition wall including stacking of serviceable materials and disposal of un-serviceable materials within 20 metres lead (Frame work such as joists, beams to be measured and paid for separately)

Dismantling doors, windows and clerestory windows, ventilators etc. (wood or steel) shutters including chowkhats, architraves, hold fasts and other attachments etc. complete and stacking them within 20 metres lead: Not exceeding 3 sqm in area

Demolition of brick work above G.L. upto floor two level including stacking of serviceable materials and disposal of un-serviceable materials within 20 metres. Lead: In cement mortar

Demolition above G.L. Upto floor two level including disposal of unserviceable materials within 20 metres lead and including cutting the necessary reinforcement and separating out from R.C.C. /R.B. Works : R.C.C. Work

Dismantling steel work upto span of 10 metres and a height of 5 metres in built up sectional in angles, tees, flats and channels including all gusset plates, bolts, nuts, beading etc and stacking the materials within 20 metres lead : Excluding dismembering

Removal of building rubbish from work site by mechanical transport for a lead of 01 km including loading unloading and levelling up of disposed material.

Section II : Site development works for the Construction of Officers club for executive of Baira Siul Power Station at Surangani

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed: all kind of soil

Excavation in drains and channels etc. in earth work including dressing of side and bed and disposing of excavated earth upto a lead of 20 metres and lift upto 1.50 metres disposed earth to be levelled and neatly dressed:50% pick work & 50% spade work

Providing and laying cement concrete 1:4:8 (1 cement:4 sand:8 graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in Foundation and plinth

Random rubble masonry/polygonal rubble masonry (uncoursed/ brought to courses) with hard stones of approved quality in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement :6 sand : 12 graded stone aggregate 20mm nominal size) at plinth level in Cement Mortar 1:6 (1 cement:6 sand)

Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in: Vertical surfaces such as walls (any thickness) partitions and the like including attached pilasters buttresses, plinth and string courses and the like.

Providing and laying cement concrete 1:2:4 (1 cement:2 Sand:4 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work in: Foundation and plinth

Brick work using common burnt clay building bricks in foundation and plinth in : Cement Mortar 1:4 (1 Cement : 4 Sand) Second Class Bricks.

15mm Cement plaster in single coat on the rough side of brick/ concrete/stone walls for interior plastering upto floor two level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth. Cement Mortar 1:4 (1Cement:4 Sand).

Steel work welded in built up sections, trusses and framed work, including cutting ,hoisting, fixing in position and applying a priming coat of red lead paint: In beams joists channels, angles, tee, flats with connecting plates or angle cleats as in main and cross beams, hip and jack rafters, Purlins connected to common rafters and the like.

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in charge: Made of G.I. wire of dia 4 mm

Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on undecorated wall surfaces(two coats)to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials.

Painting two coats (excluding priming coat) on new steel and other metal surfaces either enamel paint brushing to give an even shade including cleaning the surface of all dirt, dust and other foreign matters :- Enamel paint other than white.

Section III : Construction of Officers club for executive of Baira Siul Power Station at Surangani

Excavation in foundations, trenches etc., in earth work, lift upto 1.50 Metres stacking the excavated soil not more than 3 metres clear from the edge of the excavation and then returning the stacked soil in 15cm. layers, when required in to plinths sides of foundations etc., consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed with in a lead of 1 km by mechanical transport & 20 metres by head load complete in all respect.

Providing and laying cement concrete 1:4:8 (1 cement:4 sand:8 graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in Foundation and plinth

Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in : Foundation, footings basis of columns etc. and mass concrete.

Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in : Flat surfaces such as soffits of suspended floors, roofs, landings and the like. Floors etc. upto 200mm. In thickness.

Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in : Sides and soffits of beams, beam haunchings, cantilevers, girders, bressumers and lintels exceeding 1 Mtr. in depth in all heights from floor.

Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in : Columns, pillars, posts and struts Square, rectangular or polygonal in plan.

Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in : Stair cases with sloping or stepped soffits excluding landing.

Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in : Edges of slabs and breaks in floors and walls Under 20 cm. wide.

Providing and laying cement concrete 1:1.5:3 (1cement :1.5 sand :3 graded stone aggregate 20mm. nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in: Foundation footings bases of columns and the like and mass concrete.(Crushed aggregate)

Providing and laying cement concrete 1:1.5:3 (1cement :1.5 sand :3 graded stone aggregate 20mm. nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in: Lintels, beams girders bressumers and cantilevers upto floor two level.

Providing and laying cement concrete 1:1.5:3 (1cement :1.5 sand :3 graded stone aggregate 20mm. nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in: Column, pillars, posts and struts upto floor two level.

Providing mild steel/Tor steel reinforcement for R.C.C. work including bending and placing in position complete upto floor two level: Tor steel

Stone soling properly hand-packed filling interstices with spalls and consolidating with power road roller to the requested gradient and comber including spreading watering and rolling of binding materials moorum or earth etc. complete as per HP.PWD specification. 100 mm spread thickness (finished work including materials and labour) excluding the cost for consolidating with power road roller.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

"Random rubble masonry/polygonal rubble masonry (uncoursed/ brought to courses) with hard stones of approved quality in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement :6 sand : 12 graded stone aggregate 20mm nominal size) at plinth level in Cement Mortar 1:6 (1 cement:6 sand) "

Providing and laying cement concrete 1:2:4 (1 cement:2 Sand:4 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work in: Foundation and plinth

Brick work using common burnt clay building bricks in foundation and plinth in : Cement Mortar 1:4 (1 Cement : 4 Sand) Second Class Bricks.

Providing and laying damp proof course 50 mm thick with cement concrete 1:2:4 (1 cement:2 sand:4 graded stone aggregate 20mm nominal size) and curing complete.

Brick work using common burnt clay building bricks in super structure above plinth level in :-Cement Mortar 1:4 (1 Cement : 4 Sand) Second Class Bricks.

Half brick masonry in common burnt clay building bricks in :-Cement Mortar 1:4 (1 cement:4 sand) in super-structure above plinth level upto floor two level :Second Class Bricks.

6mm Cement plaster to ceiling In Cement mortar 1:3 (1 Cement:3 Sand)

15mm Cement plaster in single coat on the rough side of brick/ concrete/stone walls for interior plastering upto floor two level including arrises,internal rounded angles, chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth. Cement Mortar 1:4 (1Cement:4 Sand).

10mm cement plaster in single coat on fair side of brick/concrete walls for internal plastering upto floor two level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth. Cement mortar 1:4 (1 cement:4 sand).

Providing and laying machine cut, mirror polished, Italian Marble stone flooring laid in required pattern in linear portion of the building all complete as per architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. a. 18 mm thick Italian Marble stone slab,Perlato, Rosso verona, Fire Red or Dark Emperadore etc.

Providing and laying granite stone in flooring 20mm (average) thickness base of cement mortar 1:3 (1cement: 3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete. 20mm.thick

Providing and fixing 10mm thick anti skid water proof stain and impact resistant heavy duty vitrified tiles Nitco or equivalent 600 x 600mm x 10mm manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete

"Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. "

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. ( 8" X 12")

Steel work welded in built up sections, trusses and framed work, including cutting ,hoisting ,fixing in position and applying a priming coat of red lead paint: In beams joists channels ,angles, tee ,flats with connecting plates or angle cleats as in main and cross beams, hip and jack rafters,purlins connected to common rafters and the like.

Providing and fixing flush door shutters core of black board construction with frame of first class hard wood and well matched first class Indian teak ply veneering with vertical grains of cross band and face veneers on one face and commercial ply veneering with vertical grains of cross band on other face of shutters: 35 mm thick including black enamelled M.S. butt hinges.

Providing and fixing to existing door frames, 30mm thick factory made PVC panelled door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x19mm for styles and 15mm x 15mm for top & bottom rails, M.S. frame shall have a coat of steel primers of approved make and manufacture M.S. frame covered with 5mm thick heat moulded PVC "C" channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45 degree angle on either side forming style and 5mm thick, 95mm wide, PVC sheet out of which 75mm shall be flat and 20mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered on both side to form lock rail, top, bottom and lock rail shall be provided either side of the panel 10mm thick, 20mm wide cross PVC sheet be provided as gap insert for top rail and bottom rail paneling of 5mm thick both side PVC Sheet to be fitted in the M.S. frame welded/sealed to the style & rails, joints mitred and jointed with solvent cement adhesive i/c fixing of PVC shutter with existing frame with M.S. butt hinges 100x50x1.90mm size with necessary screws etc complete.

Grading roof for water treatment with Cement concrete 1:2:4 (1 cement :2 sand 4 graded stone aggregate 20 mm nominal size ).

Grading roof for water treatment withCement mortar 1:4 (1cement :4 sand)

Providing angular fillet 7.5x7.5 cm cement concrete 1:2:4 (1cement :2 sand :4 graded stone aggregate 20 mm nominal size).

Providing under layer for plinth protection of 75mm thick (unconsolidated) bed dry brick/stone aggregated 40mm nominal size with rammed and consolidated and grouted with fine sand including preparation of ground.

Providing plinth protection 50mm thick in cement concrete 1:3:6 (1 Cement : 3 Sand : 6 Graded stone aggregated 20mm nominal size)

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surfaces to give an even shade including thoroughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth including applying of putty as required for making the surface.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete.

Finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade on New work(two or more coats applied @ 1.43 litre/10sqm over & including base coat of water proofing cement paint applied @ 2.20Kg/10sqm)

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting. Ready mixed paint brushing wood primer pink.

Painting two coats(excluding priming coat) on new wood and wood based surface with enamel paint to give an even shade including cleaning the surface of dirt, dust and other foreign matter, sand papering & stoping With enamel paint other than white.

Applying priming coat over new steel & other metal surfaces after & including preparing the surface by thoroughly cleaning oil grease dirt and other foreign matter and scoured with wire brushes fine steel wool scrapers and sand paper : With ready mixed priming paint brushing red lead, Red-oxide/zinc oxide chrome complete.

Painting two coats (excluding priming coat) on new steel and other metal surfaces either enamel paint brushing to give an even shade including cleaning the surface of all dirt, dust and other foreign matters :-- Enamel paint other than white.

Providing and fixing M.S. grills of required patterns in wooden frames of windows etc. With M.S. Flats, square or round bars with round headed bolts and nuts or by screws : Plain grill.

Providing woodwork in frames of doors,windows,clerestory,windows and other frames wrought, framed and fixed in position: 2nd class deodar wood.

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm for doors windows and clerestory windows including bright finished black enamelled iron hinges with necessary screws. 30mm thick 2nd class deodar wood.

Providing and fixing panelled glazed or panelled and glazed shutters for doors windows and clerestory windows. Including black enamelled iron butt hinges with necessary screws. 35mm thick 2nd class deodar wood.

Providing and fixing 18 mm thick, 150 mm wide pelmet of flat pressed 3 layer or graded wood particle board medium density grade I, IS : 3087 marked, including top cover of 6 mm commercial ply wood conforming to IS: 303 BWR grade, nickel plated M.S. pipe 20 mm dia ( heavy type) curtain rod with nickel plated brackets, including fixing with 25x3 mm M.S. flat 10 cm long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm x 40 mm on both inner side of pelmet and rawl plugs 75 mm long etc. all complete.

Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etc. complete. 300x16mm.

Providing and fixing chromium plated brass sliding door bolts with nuts and screws etc. complete.: 300x16mm

Providing and fixing aluminium tower bolts (barrel type) anodized trans parent or dyed to required shade and colour with screws etc. complete. 250x10MM (Standard Make)

Providing and fixing aluminium tower bolts (barrel type) anodized trans parent or dyed to required shade and colour with screws etc. complete. : 150x100MM (Standard Make)

Providing fixing bright finished brass tower bolts (barrel type) with screws etc. complete. : 250x10MM (Standard Make)

Providing fixing bright finished brass tower bolts (barrel type) with screws etc. complete. : 150x10 (Standard Make)

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete. : 125MM (Standard Make)

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete. : 100MM (Standard Make)

Providing and fixing bright finished brass handles with screws etc. complete. : 125 MM (Standard Make)

Providing and fixing bright finished brass handles with screws etc. complete. : 100MM (Standard Make)

Providing and fixing M.S. hooks and eyes. 150 mm

Providing and fixing bright finished hard drawn hooks and eyes :150 mm(Standard Make)

Providing and fixing 100mm bright finished brass floor door stopper with rubber cushion screws etc., to suit shutter thickness complete

Providing and fixing bright finished or/and black enamelled iron Helical door spring 150mm.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete

Providing brick bands 7.6 cm. thick and 5cm. projected from wall face in common burnt clay building bricks laid in cement Mortar 1:4 (1 Cement : 4 Sand). SECOND CLASS BRICKS.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Brick edging (Brick laid on edge) to plinth protection with bricks including grouting with cement mortar 1:4 (1 Cement : 4 Sand). With bricks size 22.9cmx11.2cmx7cm.

Providing throating or plaster drip and moulding to R.C.C. chajja.

Providing and fixing on wall face unplasticised - Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes 110mm dia

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 15 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc (Internal work - Exposed on wall) : 20 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc (External work) : 40 mm dia nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete: 25 to 40 mm nominal bore

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid (Parryware/Hindware/ CERA)

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Range of three half stall urinals with 10 litre P.V.C.automatic flushing cistern.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer (Parryware/Hindware/ CERA)

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. : 15 mm nominal bore (Jaquar/Cera/Seiko)

Providing and fixing PVC connection pipe with brass union 45cm long 15mm nominal bore

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete: : Flexible pipe 32 mm dia

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete: : Flexible pipe 40 mm

Providing and fixing soil, waste and vent pipes: 100 mm dia, Sand cast iron S&S pipe as per IS: 1729

Providing and fixing terminal guard: 100 mm, sand cast iron S&S as per IS - 1729

Providing and fixing plain bend of required degree. : 100 mm dia, Sand cast iron S&S as per IS - 1729

Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete: 100x100x100 mm Sand cast iron S&S as per IS - 1729

Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter 100 mm.

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors: 100 mm inlet and 75 mm outlet Sand Cast Iron S&S as per IS- 1729

Providing and fixing 100 mm sand cast Iron grating for gully trap.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931: 15 mm nominal bore

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink with drain board :510x1040 mm bowl depth 250 mm

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: Inside dimensions 455x610 mm and 45 cm deep for single pipe line :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore

Providing and fixing toilet paper holder : C.P. brass

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design :100x100 mm size P type, With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work): 20MM Nominal Bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work): 40MM Nominal Bore

Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : For 100MM dia pipe

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour-450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Section IV : Demolition of existing Type V Quarters 01 & 02 and Type IV quarters 07 to 10 at Officer colony of BSPS at Surangani

Dismantling roofing including ridges, hips, valleys, gutters etc. stacking the serviceable materials and disposal of un-serviceable materials within 20 metres lead: G.I. Sheet roofing

Dismantling wood work. Wrought framed and fixed in frames other frames and trusses of span upto 10 metres and height between ridge and floor level stacking the serviceable materials and disposal of un-serviceable materials with in 20 metres lead: Sectional area average 40 sq.cm. Or over

Dismantling cement asbestos celotax/hard board in ceiling or partition wall including stacking of serviceable materials and disposal of un-serviceable materials within 20 metres lead (Frame work such as joists, beams to be measured and paid for separately)

Dismantling doors, windows and clerestory windows, ventilators etc. (wood or steel) shutters including chowkhats, architraves, hold fasts and other attachments etc. complete and stacking them within 20 metres lead: Not exceeding 3 sqm in area

Demolition of brick work above G.L. upto floor two level including stacking of serviceable materials and disposal of un-serviceable materials within 20 metres. Lead: In cement mortar

Demolition above G.L. Upto floor two level including disposal of unserviceable materials within 20 metres lead and including cutting the necessary reinforcement and separating out from R.C.C. /R.B. Works : R.C.C. Work

Disposal of building rubbish for a lead of 1 km in mechanical transport

Section V : Site development works for the Construction of 02 Nos. Type V Quarters of Baira Siul Power Station at Surangani

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed: all kind of soil

Excavation in drains and channels etc. in earth work including dressing of side and bed and disposing of excavated earth upto a lead of 20 metres and lift upto 1.50 metres disposed earth to be levelled and neatly dressed:50% pick work & 50% spade work

Providing and laying cement concrete 1:4:8 (1 cement:4 sand:8 graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in Foundation and plinth

Random rubble masonry/polygonal rubble masonry (uncoursed/ brought to courses) with hard stones of approved quality in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement :6 sand : 12 graded stone aggregate 20mm nominal size) at plinth level in Cement Mortar 1:6 (1 cement:6 sand)

Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in: Vertical surfaces such as walls (any thickness) partitions and the like including attached pilasters buttresses, plinth and string courses and the like.

Providing and laying cement concrete 1:2:4 (1 cement:2 Sand:4 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work in: Foundation and plinth

Brick work using common burnt clay building bricks in foundation and plinth in : Cement Mortar 1:4 (1 Cement : 4 Sand) Second Class Bricks.

15mm Cement plaster in single coat on the rough side of brick/ concrete/stone walls for interior plastering upto floor two level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth. Cement Mortar 1:4 (1Cement:4 Sand).

Steel work welded in built up sections, trusses and framed work, including cutting ,hoisting, fixing in position and applying a priming coat of red lead paint: In beams joists channels, angles, tee, flats with connecting plates or angle cleats as in main and cross beams, hip and jack rafters, Purlins connected to common rafters and the like.

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in charge: Made of G.I. wire of dia 4 mm

Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on undecorated wall surfaces(two coats)to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials.

Painting two coats (excluding priming coat) on new steel and other metal surfaces either enamel paint brushing to give an even shade including cleaning the surface of all dirt, dust and other foreign matters :- Enamel paint other than white.

Section VI : Construction of 02 Nos. Type V Quarters of Baira Siul Power Station at Surangani

Excavation in foundations, trenches etc., in earth work, lift upto 1.50 Metres stacking the excavated soil not more than 3 metres clear from the edge of the excavation and then returning the stacked soil in 15cm. layers, when required in to plinths sides of foundations etc., consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed with in a lead of 1 km by mechanical transport & 20 metres by head load complete in all respect.

Providing and laying cement concrete 1:4:8 (1 cement:4 sand:8 graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in Foundation and plinth

Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in: Foundation, footings basis of columns etc. and mass concrete.

Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in: Flat surfaces such as soffits of suspended floors, roofs, landings and the like. Floors etc. upto 200mm. In thickness.

Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in: Sides and soffits of beams, beam haunchings, cantilevers, girders, bressumers and lintels exceeding 1 Mtr. in depth in all heights from floor.

Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in:Columns, pillars, posts and struts Square, rectangular or polygonal in plan.

Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in: Stair cases with sloping or stepped soffits excluding landing.

Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in: Edges of slabs and breaks in floors and walls Under 20 cm. wide.

Providing and laying cement concrete 1:1.5:3 (1cement :1.5 sand :3 graded stone aggregate 20mm. nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in: Foundation footings bases of columns and the like and mass concrete.(Crushed aggregate)

Providing and laying cement concrete 1:1.5:3 (1cement :1.5 sand :3 graded stone aggregate 20mm. nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in: Lintels, beams girders bressumers and cantilevers upto floor two level.

Providing and laying cement concrete 1:1.5:3 (1cement :1.5 sand :3 graded stone aggregate 20mm. nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in: Column, pillars, posts and struts upto floor two level.

Providing mild steel/Tor steel reinforcement for R.C.C. work including bending and placing in position complete upto floor two level: Tor steel

Stone soling properly hand-packed filling interstices with spalls and consolidating with power road roller to the requested gradient and comber including spreading watering and rolling of binding materials moorum or earth etc. complete as per HP.PWD specification. 100 mm spread thickness (finished work including materials and labour) excluding the cost for consolidating with power road roller.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

"Random rubble masonry/polygonal rubble masonry (uncoursed/ brought to courses) with hard stones of approved quality in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement :6 sand : 12 graded stone aggregate 20mm nominal size) at plinth level in Cement Mortar 1:6 (1 cement:6 sand) "

Providing and laying cement concrete 1:2:4 (1 cement:2 Sand:4 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work in: Foundation and plinth

Brick work using common burnt clay building bricks in foundation and plinth in : Cement Mortar 1:4 (1 Cement : 4 Sand) Second Class Bricks.

Brick work using common burnt clay building bricks in super structure above plinth level in :-Cement Mortar 1:4 (1 Cement : 4 Sand) Second Class Bricks.

Half brick masonry in common burnt clay building bricks in :-Cement Mortar 1:4 (1 cement:4 sand) in super-structure above plinth level upto floor two level :Second Class Bricks.

6mm Cement plaster to ceiling In Cement mortar 1:3 (1 Cement:3 Sand)

15mm Cement plaster in single coat on the rough side of brick/ concrete/stone walls for interior plastering upto floor two level including arrises,internal rounded angles, chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth. Cement Mortar 1:4 (1Cement:4 Sand).

10mm cement plaster in single coat on fair side of brick/concrete walls for internal plastering upto floor two level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth. Cement mortar 1:4 (1 cement:4 sand).

Providing and laying granite stone in flooring 20mm (average) thickness base of cement mortar 1:3 (1cement: 3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete. 20mm.thick

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. : Size of Tile 600x600 mm

Providing and fixing 10mm thick anti skid water proof stain and impact resistant heavy duty vitrified tiles Nitco or equivalent 600 x 600mm x 10mm manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 13755 of NITCO, ORIENT, SOMANY KAJARIA, or equivalent make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigment etc., complete.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. ( 8" X 12")

Steel work welded in built up sections, trusses and framed work, including cutting ,hoisting ,fixing in position and applying a priming coat of red lead paint: In beams joists channels ,angles, tee ,flats with connecting plates or angle cleats as in main and cross beams, hip and jack rafters,purlins connected to common rafters and the like.

Providing and fixing flush door shutters core of black board construction with frame of first class hard wood and well matched first class Indian teak ply veneering with vertical grains of cross band and face veneers on one face and commercial ply veneering with vertical grains of cross band on other face of shutters: 35 mm thick including black enamelled M.S. butt hinges.

Providing and fixing to existing door frames, 30mm thick factory made PVC panelled door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x19mm for styles and 15mmx15mm for top & bottom rails, M.S. frame shall have a coat of steel primers of approved make and manufacture M.S. frame covered with 5mm thick heat moulded PVC "C" channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45 degree angle on either side forming style and 5mm thick, 95mm wide, PVC sheet out of which 75mm shall be flat and 20mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered on both side to form lock rail, top, bottom and lock rail shall be provided either side of the panel 10mm thick, 20mm wide cross PVC sheet be provided as gap insert for top rail and bottom rail paneling of 5mm thick both side PVC Sheet to be fitted in the M.S. frame welded/sealed to the style & rails, joints mitred and jointed with solvent cement adhesive i/c fixing of PVC shutter with existing frame with M.S. butt hinges 100x50x1.90mm size with necessary screws etc complete.

Grading roof for water treatment with Cement concrete 1:2:4 (1 cement :2 sand 4 graded stone aggregate 20 mm nominal size ).

Providing angular fillet 7.5x7.5 cm cement concrete 1:2:4 (1cement :2 sand :4 graded stone aggregate 20 mm nominal size).

Providing under layer for plinth protection of 75mm thick (unconsolidated) bed dry brick/stone aggregated 40mm nominal size with rammed and consolidated and grouted with fine sand including preparation of ground.

Providing plinth protection 50mm thick in cement concrete 1:3:6 (1 Cement : 3 Sand : 6 Graded stone aggregated 20mm nominal size)

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surfaces to give an even shade including thoroughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth including applying of putty as required for making the surface.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete.

Extra over item No 6.020 for painting with plastic emulsion paint of approved brand and manufacture on ceiling and/or sloping roofs.

Finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade on New work(two or more coats applied @ 1.43 litre/10sqm over & including base coat of water proofing cement paint applied @ 2.20Kg/10sqm)

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting. Ready mixed paint brushing wood primer pink.

Painting two coats(excluding priming coat) on new wood and wood based surface with enamel paint to give an even shade including cleaning the surface of dirt, dust and other foreign matter, sand papering & stoping With enamel paint other than white.

Applying priming coat over new steel & other metal surfaces after & including preparing the surface by thoroughly cleaning oil grease dirt and other foreign matter and scoured with wire brushes fine steel wool scrapers and sand paper : With ready mixed priming paint brushing red lead, Red-oxide/zinc oxide chrome complete.

Painting two coats (excluding priming coat) on new steel and other metal surfaces either enamel paint brushing to give an even shade including cleaning the surface of all dirt, dust and other foreign matters :-- Enamel paint other than white.

Providing and fixing M.S. grills of required patterns in wooden frames of windows etc. With M.S. Flats, square or round bars with round headed bolts and nuts or by screws : Plain grill.

Providing woodwork in frames of doors, windows, clerestory, windows and other frames wrought, framed and fixed in position: 2nd class deodar wood.

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm for doors windows and clerestory windows including bright finished black enamelled iron hinges with necessary screws. 30mm thick 2nd class deodar wood.

Providing and fixing panelled glazed or panelled and glazed shutters for doors windows and clerestory windows. Including black enamelled iron butt hinges with necessary screws. 35mm thick 2nd class deodar wood.

Providing and fixing 18 mm thick, 150 mm wide pelmet of flat pressed 3 layer or graded wood particle board medium density grade I, IS : 3087 marked, including top cover of 6 mm commercial ply wood conforming to IS: 303 BWR grade, nickel plated M.S. pipe 20 mm dia ( heavy type) curtain rod with nickel plated brackets, including fixing with 25x3 mm M.S. flat 10 cm long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm x 40 mm on both inner side of pelmet and rawl plugs 75 mm long etc. all complete.

Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etc. complete. 300x16mm.

Providing and fixing aluminium tower bolts (barrel type) anodized trans parent or dyed to required shade and colour with screws etc. complete. : 200x10mm (Standard Make)

Providing and fixing aluminium tower bolts (barrel type) anodized trans parent or dyed to required shade and colour with screws etc. complete. : 150x10mm (Standard Make)

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete. : 125 mm (Standard Make)

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete. : 100 mm (Standard Make)

Providing and fixing M.S. hooks and eyes. 150 mm

Providing and fixing oxidized M.S. hasps and stapples (safety type) with necessary screws etc. complete. 150 mm

Providing and fixing 100mm bright finished brass floor door stopper with rubber cushion screws etc., to suit shutter thickness complete

Providing and fixing bright finished or/and black enamelled iron Helical door spring 150mm.

Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete

Providing brick bands 7.6 cm. thick and 5cm. projected from wall face in common burnt clay building bricks laid in cement Mortar 1:4 (1 Cement : 4 Sand). SECOND CLASS BRICKS.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Brick edging (Brick laid on edge) to plinth protection with bricks including grouting with cement mortar 1:4 (1 Cement : 4 Sand). With bricks size 22.9cmx11.2cmx7cm.

Providing throating or plaster drip and moulding to R.C.C. chajja.

Providing and fixing angle iron cupboard frames manufactured from M.S.Angle iron section 25X25X5mm thickness including hinges jamb,lock jamb,beed and if required angle thrashold of mild steel angle 25X25 mm welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb including steel butt hinges 2.5 mm thick with provision for locking arrangement and shock absorber as specified and applying a coat of approved steel primer after preteatment of the surface as directed by Engineer-in-Charge.

Providing and fixing 19mm thick Commercial Board water proof shutters for cup boards i/c fixing with nickel plated piano hinges with screws etc complete

Providing and fixing 19mm thick water proof commercial board in shelves/box for cup board with butt joints & fixing with nails & screws etc complete

Providing and fixing on wall face unplasticised - Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes 110mm dia

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 15 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc (Internal work - Exposed on wall) : 20 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc (External work) : 40 mm dia nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete: 25 to 40 mm nominal bore

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid (Parryware/Hindware/ CERA)

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer (Parryware/Hindware/ CERA)

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. : 15 mm nominal bore (Jaquar/Cera/Seiko)

Providing and fixing PVC connection pipe with brass union 45cm long 15mm nominal bore

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete: Flexible pipe: 32 mm dia

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete: Flexible pipe: 40 mm dia

Providing and fixing soil, waste and vent pipes:75 mm diameter, Sand cast iron S&S pipe as per IS: 1729

Providing and fixing soil, waste and vent pipes:100 mm diameter, Sand cast iron S&S pipe as per IS: 1729

Providing and fixing terminal guard: 100 mm, sand cast iron S&S as per IS - 1729

Providing and fixing terminal guard: 75 mm, sand cast iron S&S as per IS - 1729

Providing and fixing plain bend of required degree. : 100 mm dia, Sand cast iron S&S as per IS - 1729

Providing and fixing plain bend of required degree. : 75 mm dia, Sand cast iron S&S as per IS - 1729

Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete: 100x100x100 mm Sand cast iron S&S as per IS - 1729

Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete: 75x75x75 mm, Sand cast iron S&S as per IS - 1729

Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter 100 mm.

Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter 75 mm.

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors: 100 mm inlet and 75 mm outlet Sand Cast Iron S&S as per IS- 1729

Providing and fixing 100 mm sand cast Iron grating for gully trap.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931: 15 mm nominal bore

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink with drain board :510x1040 mm bowl depth 250 mm

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: Inside dimensions 455x610 mm and 45 cm deep for single pipe line :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet: 100 mm diameter

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore

Providing and fixing toilet paper holder : C.P. brass

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design :100x100 mm size P type, With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work): 20mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work): 40mm nominal bore

Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : For 100MM dia pipe

Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : For 75MM dia pipe

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour-450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. 15 MM nominal dia

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

ajay kumar

Sarwar Shah Govt Contractor

Aakar Infra Engineers PVT Ltd