Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | 1₹4.4 LAccepted-Finance M 36 HOUSING UNIT MATHAIYANKUTTAI PO METTUR DAM 636452 | METTUR DAM | SALEM | TAMIL NADU | 636452 | 1 | Accepted-Finance satisfied | |
| 2 | 2₹4.7 L+₹33,720 (7.73%)Accepted-Finance M 18 HOUSING BOARD UNIT MADAYANKUTTAI POST METTUR DAM 636 452 | METTUR DAM | SALEM | TAMIL NADU | 636452 | 2 | Accepted-Finance satisfied |
Tender Value
Refer Docs
EMD Value
₹5,800
Closing Date
9 May 2022, 2:00 pmClosed
Superintending Engineer /Mechanical-I/MTPS-I
Office of the Superintending Engineer / Mechanical -I Mettur Thermal Power Station- I Mettur Dam-636406
MTPS I BM Boiler Statutory Inspection 2022 23 Unit I APH A Checking of rotor level sector plate level and axial seal plate alignment Water washing of cold end baskets and other related works
2022_EB_229722_2
SE / M-I / MTPS-I / BM / OT. 62 /2022-23
Open Tender
Power/Energy Projects/Products
Works
10 days
Mettur Thermal Power Station-I / Mettur Dam
As per the Tender Specification
4 documents required · 4 mandatory
₹0
₹5,800
Yes
13 May 2022
2 May 2022
10 May 2022
2 May 2022
9 May 2022
2 May 2022
Amount
Opening of all manhole doors, and closing manhole doors after completion of work including changing of asbestos ropes and clamps in the doors.
Removal of ash deposit around guide bearing area and inside the APH.
Charges for cutting and removing of rigid stoppers checking and correction of rotor leveling, checking and correction of critical distance between guide bearing housing and housing sleeve and fixing, welding the rigid stoppers and provide shim packing in between guide bearing housing and permanent stoppers.
Charges for leveling and aligning of the radial sector plates and axial seal plates with respect to the rotor axis.
Charges for finding the high point in 'T' bar, adjusting the bypass seals to correct clearance and clamping properly in both hot and cold ends of APH.
Inspection of support bearing by removing the cover, drain oil, cleaning and checking level etc.
Charges for fixing up straight edge after finding the low point of sector plate, adjusting the radial seals to correct clearance and clamping the seals in both hot end and cold end of APH.
Charges for fixing up straight edge after finding the low point of axial seal plate, adjusting the axial seals to correct clearance and clamping the seals properly.
Charges for transporting of 6mm M.S./ Checkered plates from Central Stores/MTPS to Boiler area, cutting into required size, leading, lifting, positioning on the eroded portions of the APH housing and welding the same.
Cleaning of steam coil Air pre heater.
Water washing of Air pre heater.
Removal of cold end baskets from its position, leading to the adjacent area of Air Pre heaters, dry cleaning, high pressure jet water cleaning and then air cleaning of the cold end baskets, putting the heating elements after rectification of cold end diaphragm and cold end gratings.
Charges for Rectification of Hot end stationary Spool and renewing the retainer ring, Packing rings and etc.,
Removal of accumulated ash at center section connecting plate area of APH.
Consumables and T & Ps for item S.No.1 to 14.
THIAGARAJAN ENGINEERING CONTRACTOR
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .