ADDN ALTN TO BLDG NO P 9 AND P 7 A UNDER GE (EAST) DELHI CANTT 10

Amount

Demolition of cement concrete (reinforced) of any position and any description not otherwise specifically provided for and including reinforcement required to facilitate demolition upto and including and removal of debris and rubbish out side MoD land complete all as specified and directed.

Demolition of brick work built in cement mortar including all quoins,arches,pillars,etc but excluding ashlar facings dressed stone work and precast concrete articles or cutting openning through brick wall built in CM for door and window and other openning including removal of debris and rubbish out side MoD land complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in any position and discription ( below or above ground level ) including removal of rubbish out side complex (MOD land), complete all as specified and directed.

Dismantling of PVC water tanks of exc 250 litres and n.exc 500 litres capacity of any condition or type complete all as specified and directed.

Dismantling of Cast Iron pipe up to 100 mm bore complete all as specified and directed.

Taking up or down 15 mm bore GI tubing and connections including removal of store complete all as specified and directed.

All as per item No. 6 above but 20 mm bore

Taking down chowkhats or frames exc. 1.5 Sqm and n.exc 4 Sqm each with shutters (without taking off shutters from frames) complete all as specified and directed.

Taking down chowkhats or frames not exc. 1.5 Sqm each with shutters (without taking off shutters from frames) complete all as specified and directed.

Taking down shutters of any description exc 1 sqm and not exc 2 sqm each and refixing in the same or other opening as required at site complete all as specified and directed. Note : The rate quoted by the contractor are inclusive of taking down old mild steel hinges carefully without damaging and refixing in the same or other opening as directed. Nothing extra cost will be allowed in this account.

Dismantling of floor, hearth or wall tiling incl cement mortar bedding (but not backing) removing rubbish of the premises complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster, terrazzo dado in any thickness from brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc including removal of rubbish,vegetation etc outside complex (MOD land) complete all as specified and directed.

Cutting openning through brick wall built in CM for door and window and other openning or enlarging existing openings,converting window into door opening etc or cutting out defective brick work for under pinning including providing fixing and removing shoring ,cleaning and stacking brick including removal of debris and rubbish out side MoD land complete all as specified and directed.

M&L for providing and fixing factory made UPVC white colour siliding window three track made xtruded profiles with all thickness of 2.3mm, having profile with hollow section with multi chamber. Frame size (60mm x 62mm), sash (42mmx67mm), sliding inter lock (one vertical length in each shutters) (45.5mmx28mm),glazing head (24.50mmx 16), mitered cut and fusion welded in all corners including drilling of holes for fixing hardware and drainage of water etc. including EPDM gaskets 1.2, thick glavanised steel frame (30mmx21.50mm), sash (30mmx 18 mm) profile to be inserted in required profile frase will be fixed to the wall with 8mmx100mm long fasteners including hardware vz touch lock of zinc alloyed ( white powerder coated), steel roller system , aluminium track on bottom rail two track sliding frame wool pine for sliding sash and interlock complete. Note: The unit rate quoted by the contractor included cost of glass and SS wire mesh. Net openning will be measured for payment purpose. (Make:Okotech Aparno,H20 Solution,Fenesta or equavalent

Providing and fixing factory made UPVC ( white colour Casement (Openable) window made of extruded profiles with wall thickness of 2.3mm, having profile with hollow section with multi chamber, Frame (60mm x 58mm). sash (60mm x 73mm), T profile (One vertical length in between two shutters) (60mm x 74mm), Glazing bead (35mm x 20mm) mitered cut And fusion welded at all corners. including (drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. E.PDM gasket. 1.2 thick galvanized steel frame (28mm x 21. 5mm, sash (31mm x 27.5mm), T profile (27mm x 17mm) to be inserted in required profile. frame will be fixed to wall with 8 mm x 100mm long- fasteners includin hardware viz casement handle made of zinc alloyed (white powder coated), butt hinges of zinc alloyed (white powder coated), transmission gear made of mild steel with multi point locking s' stem complete. Note: The unit rate quoted by contractor included cost of glass. Net opening will measured for payment purpose.) Okotech Aparno,H20 Solution,Fenesta or equavalent

M&L for providing and fixing factory made UPVC (white colour casement (Openable) Door made of extruded profile with wall thickness of 2.3mm having profileof hollow section with multi chamber. Frame size (60mmx58mm), sash (60minx78mm), T profile having one vertical length in between two shutters of size (60mmx 74mm) glazing head (35mmx 20mm) mitered cut and fusion welded at all corners including making holes for fixing hardware and drainage of water, provision of EPDM gasket 1.2 thick galvanised steel frame (28mmx21.50mm), sash (31mmx27mm). T profile (27x17mm) to inserted in required profile frame will be fixed to wall with 8mm x 100mm long fasteners including necessary hardware viz casement (door handle,tower bolt,stopper,locking arrangemnt,and other acceessories )made of zinc alloyed (white powder coated), corner striker, secondary strikers, cylinder, transmission gear made of mild steel with multi point locking system with strikes, hinges of zinc alloyed (white powder eoated) complete as specified. (Note:The unit rate quoted by contractor included cost of glass and board. Net opening will be measured for payment purpose.) Make:-Okotech Aparno,H20 Solution,Fenesta or equavalent

M&L preparation of any description and size of untreated wood and wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L complete removal of existing treatement from old steel surface and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by E.I.C.

M&L complete removal of existing treatment from old steel surface not exc 10 cm width or girth when unconnected with other painting or or when painted in different tint and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by E.I.C.

M&L Granite of 18 to 20mm thick with uniform texture (table rubbed and polished) in steps, window cills,cooking platforms,wash basin counter and like in cement mortar (1:4) including pointing with white cement (1:2) using marble dust with admixture of pigment to match with marble shade of makrana dogri green colour stone for Kitchen cooking platform laid over and including 15mm thick screed bed in cement mortar (1:6) polishing bevelled edges of corner,moulding etc complete all as specified and directed.

All as per serial item no 20 above but on vetical surfaces like Jambs,Pillar ,Riser etc 10 mm rendering in cement mortar 1:4 completed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with steel wire staples, complete all as specified and directed

M&L for Brick work with sub class B bricks of old size, straight or curved on plan exc 6 m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L for Brick work with sub class 'B' bricks straight or curved on plan to any radious in half brick thick wall built in CM 1:4 complete all as specified and directed.

S&F Mild steel TMT bars of 10 mm dia and over cut to length bent to shape required including cranking, bending etc and S&F for stengthening existing reinforcement by use of mild steel bars of any dia , cut to length, bent to shape required, including cranking, bending spirally and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. (Make : Tata steel or equivalent)

S&F TMT bars 5mm and over upto and including 10mm dia in stirrups, spacers and binders bent to shape required,including binding with mild steel wire (annealed) not less than .9mm dia complete all as specified.(Make : Tata steel or equivalent)

M&L for providing reinforced cement concrete (1:2:4) type B-1 using 20 mm graded crushed stone aggregate as in kitchen slab, Chajjas, lintels complete all as specified and directed. The work will be executed upto G+3 Stories building.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out and getting out in soft/loose soil complete all as specified and directed.

Returning filling in including spreading leveling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified and as directed.

Removing excavated material n exc 50 m and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified.

M&L PCC 1:4:8 type D-2 (using 40 mm graded stone agg) as in foundation complete all as specified & directed.

M&L for RCC M-25 (20mm graded aggregate) as in foundations footings, plinth beams etc all as specified & directed.

M&L for RCC M-25 (20mm graded aggregate) as in columns, pillars etc all as specified & directed.

M&L for RCC M-25 (20mm graded aggregate) as in beams, lintels etc all as specified & directed.

M&L for RCC M-25 (20mm graded aggregate) as in chajjas etc all as specified & directed.

M&L for RCC M-25 (20mm graded aggregate) as in slab type Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified

Form work to soffit of suspended slabs such as roof slabs, floor slabs, landings and similar work, n exc 200mm thick (horizontal or sloping) complete all as specified.

M & L formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressumers, lintes,cantilevers, shelves including supports, overhangs, etc also splays beteen floors and beams finished rough surfaces of concrete complete all as specified.

Formwork to chajjas, chullah hoods, similar items including edges all as specified.

Providing and fixing glass reinforced concrete (G.R.C) panelss in approved size pattern,design,thickness and colour of M/s GRC Terra Firma make or equavalent .Quart,fine silica sand,Alkali resistant glass fibre manufacture by NEG or equavalent ,super plasticizers manufactue by NEG or equavalent,super plasticizers mamufactureed by BASF or equavalent,polymer manufactureed by Basf or equavalent and UV resistant synthetic inoganic pigment should be used for pigmentation manufactureed by Bayferrox(Germony)b or equavalent .The material casting should be used for pigmentation manufactureed by Reckli or equavalent.The fixing of screen should be Dry fixing i.e to be done with stailess steel(SS-304)L shaped brackets ,fasteners and pins completedas and directed.

M & L for providing 40 mm thick PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in floor , finished even and smooth without using extra cement complete all as specified and directed by Engr-n-Charge.

M&L Kota stone slab 20-25 mm thick with uniform texture in floor with laid over and including 20 mm thick screed in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed

M&L kota stone slab with uniform texture of 20-25 mm thick in treader of steps, riser of steps, skirting, dado and pillars in one single piece (size decided by Engineer-in-Charge) laid over and including cement screed 10mm thick in cement morter 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing , bevelled edge of corner etc complete all as specified and directed.

M&L for rendering 5 mm thick in cement mortar 1:4 as in ceiling new/old surface finished even and smooth without using extra cement to match with existing surface complete all as specified and directed.

M&L for rendering 12 mm thick in cement mortar 1:6 other than fair face of brick work/ concrete surfaces and finished even and smooth without using extra cement complete all as specified.

M&L for rendering 15mm thick plastering in cement mortar 1:4 in walls finished even and smooth to match with existing surface complete all as specified and directed. Note for Item No 47 to 49 : Sand for plastering shall be 100% coarse sand (Badarpur/Stone dust) conforming to the sample appved by GE.

M&L for preparation of old decorated external wall surface (As colour approved )by complete removal of existing treatement by mechanised sander of Berger paints or equivalent makes viz Xpress sanding machine having suction vaccum bag or by manual scrapping tools where mechincal removeal is not possible and applying a layer of 2 mm thick wall care putty,over plaster of paris putty of 2 mm thickness again sand papering thus making surface smooth and applying two coat of wheather proofing exterior acrylic emulsion paint premium quality on wall over a coat of primer on surfaces complete all as specified.

M&L for preparation of new/old plastered surface of wall and applying two coat of plastic emulsion paint (As colour approved )over a coat of priming coat including all wall care putty on newly/old plastered walls of 2-3mm thick over applying plaster of paris putty of 2 mm thickness incl removal of existing treatment on surfaces of walls by scrapping down with mechanical grinder complete all as specified and directed.

M&L for preparation of new/old plastered surface of ceiling and applying two coat of plastic emulsion paint (as colour approved) over a coat of priming coat including all care putty on newly/old plastered walls of 2-3mm thick wall care putty over applying plaster of paris putty of 2 mm thicknessincl removal of existing treatment on surfaces of walls by scrapping down with mechanical grinder complete all as specified and directed.

M&L for Vitrified tiles (Double charge) light Shade 10mm thick (square/rectangular) polished, area of each tiles exc 0.42 Sqm but not exceeding 1.00sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6 complete all as specified.

All as per serial item no 53 above but on vetical surfaces like Jambs,Pillar ,Riser etc 10 mm rendering in cement mortar 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including backing coat of 10mm thick CM 1:4 on brick masonry/concrete surfaces finished even to receive tiles complete all as specified and as directed.

M&L for double/Single leaf glass door with 10 mm thick tinted toughned glass door mounted on floor spring with hood open arm with top & bottom patch fittings including corner lock strike plate and european profile cylinder handle 32mmx300mm in Satine SS finish including stainless steel brackets,Handle 250 mm long and all other accessories incl dismantling of old and rubbish off the permises as per approved design complete all as specified.

M&L joint free Non skid Coloured ceramic tile 600x600x7-8 mm thick free jointed as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L Coloured Glaze ceramic tiles 300x600 x 7 to 8mm thick, as in vertical surfaces of wall such as dado/skirting, set and jointed in neat cement slurry and pointed in white or coloured cement over and including 10mm thick rendering in CM 1:4 complete all as specified.

S&F 15mm bore GI tubing medium grade with all fittings and fixed to wall and ceiling or laid in floors(canceal) incl two coat of bituminious paint etc complete all as specified and directed.

All as per item No 58 above but 20 mm bore.

S&F white colour Rotational moulded polyethylene water storage tank 500 litres capacity, ISI marked triple layer construction (cylindrical vertical closed top), hoisted & fixed in position including all fittings complete all as specified and as directed.

S&F stainless steel sink AISI 316 grade with drainage board of 1 mm thick kitchen or laboratory with plug , washer and waste, bedding in cement mortar to dwarf wall or including fixing cantilever brackets and overall size 915mmx 460mm bowl size 410mm x330mm x160mm etc compete all as specified and directed.

S & F Brass CP sink mixer for mixing hot & cold water screwed down for iron pipe 15 mm bore, screwed down high pressure, screwed for iron pipe and fixed complete all as specified and directed.((Make Jaquar Model No: CON-309KNB or equivalent as given in approved make list)

S&F Chromium plated in repair towel rail, 20mm dia, (Rectanguler type) 60cm long between flanges of brass chromium plated and fixed with Make Jaquar Model No ACN-1115N or as given in approved make list)

Taking down existing ceiling of any type and any description and provn of E-board 4mmthick self design type tiles ceiling on GI Powder coated channel/Tee/Grid of frame work with the following specification including cutting holes to brick wall built in cement mortar & making good in cm 1:3 of cement concrete 1:2:4 type BO as required :- (a) Plugging to wall around the rooms & supplying & fixing GI Powder coated angle of size 25x25x1.0 mm (b) S&F of 1.60 mm dia GI wire suspenders with adjustable clamps including fixing to ceiling dash free fasterers (c) S&F 25 x25 x1.5mm GI Powder coated tee as in main & cross members at 595mm c/c supported suspenders alongwith adjustable clamp to maintain level . ( d) S&F E-board 4mmthick self design type ceiling tiles of size 610mm x610mm confirming to relevant IS in squares of GI Powder coated Tee with clips made to shape. Shade and pattern of E- board shall be as approved by GE

S&F in repair vitreous china counter type wash basin under counter Designer type size 475x465x185 mm fixed under granite slab with all fitting and fixture complete all as specified.(Make Jaquar Model No: JDS-WHT-25903 or equivalent as given in approved make list)

S&F Brass CP basin mixer in repair for mixing hot & cold water screwed down for iron pipe 15 mm bore, screwed down high pressure, screwed for iron pipe and fixed complete all as specified and directed.(Make: Make Jaquar Model No: KUB-CHR-35052FB or equivalent as given in approved make list))

S&F in repair CP Towel Rack 600mm long with lower hanger of CP fixed with and including Chromimum plated brass screws and wooden/plastic cleats. (Make Jaquar Model No: ACN-1181N or or equivalent as given in approved make list)

S&F for soap dispenser with glass bottle fixed with and including Chromimum plated brass screws and wooden/plastic cleats. (Make Jaquar Model No: ACN-1135N or or equivalent as given in approved make list)

S&F Vitreous china wash down water closet pan Wall hung WC, Make Jaquar Model No: ARS - WHT- 39951 or as given in approved make list with PP seat cover, hinges, accessories set, size 575x360x360 full set or other equivelent make from list, including 10 lit capacity flushing cistern(canceal in wall) and fixed with brass screw complete all as specified and as directed.

S&F single lever exposed parts kit of Hiflow divertor consisting of operating lever wall flange (with seals)& button complete all as specified and as directed. (Make Jaquar Model No: KUB-35079FK or equivalent as given in approved make list)

S&F in repairs 15 mm bore Angle valve cast copper alloy fancy type Chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe complete all as specified and directed . (Make Jaquar Model No: ORP-10053PM or equivalent as given in approved make list)

S&F in repairs 15 mm bore double Angle valve (two way) cast copper alloy fancy type Chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe complete all as specified and directed .

S&F in repair CP wall mixture diverted 15 mm bore cast copper alloy Chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe etc complete all as specified and directed. ( Make Jaquar Model No: ORP-10118PM or equivalent as given in approved make list)

S&F for Body shower 100x100 mm(ABS chrome plateed face plate with rubit cleaning system) complete all as specified and directed. ( Make Jaquar Model No: BSH-CHR-1751 or equivalent as given in approved make list)

S&F in repairs 15mm bore bib taps standard of Chromium plated high pressure screwed for iron pipe and fixed etc. complete all as specified and directed. ( (Make Jaquar Model No: ORP-10037PM or equivalent as given in approved make list))

S&F in repairs CP brass shower rose 240x240mm fancy type with chromium plated arm fixed to 15mm pipe of revolving type complete all as specified and directed. (Make Jaquar Model No: OHS-CHR-1629 or equivalent as given in approved make list)

S&F in repair Stainless steel grating 100mm dia of best quality as approved by GE including fixing in CM 1:4 to floor/nahani traps etc complete all as specified and directed.

S&F in repairs 15 mm bore canceal stop valve cast copper alloy fancy type Chromium plated fancy type with long shunk and cup with crutch or butterfly handle screwed both ends for iron pipe complete all as specified and directed . (Make Jaquar Model No: ORP-10083KPM or equivalent as given in approved make list)

S&F in repairs cast copper alloy CP toilet paper holder with flap fixed with plug and brass screw completed all as specified .(Make- Jaquare Cat No- ACN-1153N or equivalent as given in approved make list)

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with CP bracket guard and railing 60cm long complete all as specified and directed.(Make Jaquar Model No: ORP-10083KPM or or equivalent as given in approved make list)

S&F in repairs health faucet chromium plated brass completed all as spd Make - Jaguar cat No-ALD573 or equivalent make from the approved list

S&F in repair 32mm Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap ,nipple and fixed.

S&F in repair CP fancy type rectangular towel ring fixed with and including CP brass screws Complete all as specified.(Make: Jaquar Model No: ACN-1121N or equivalent as given in approved make list)

S&F in CP fancy type Tumbler holder fixed with and including CP brass screws Complete all as specified.(Make: Jaquar Model No: AKP-35741P or equivalent as given in approved make list)

S&F in repair corner glass shelf 225x225mm radius consisting of 5.5mm thk sheet glass with CP brass brackets with 02 Nos of CP railing in each set complete all as specified..( (Make Jaquar Model No: ACN-1173N or equivalent as given in approved make list)

S&F in repair for soap dish cast copper alloy fancy type chormium plated of standard size and quality complete all as specified and as directed by Engr-in-Charge..( (Make Jaquar Model No: ACN-1131N or equivalent as given in approved make list)

S&F for double arm wall mounted reversible plain/magnifying(X3) pivotal mirror cast copper alloy fancy type chormium plated of standard size and quality complete all as specified and as directed by Engr-in-Charge..( (Make Jaquar Model No: ACN-1193N or equivalent as given in approved make list)

S&F in repair fancy type Curtain rods decorative type stainless steel 25mm nominal dia of approved quality(Make VISTA) (3mm wall thickness) including fixing of two number decorative brackets fixed in brick/concrete wall, Two number of latto on both ends of curtain rods ( The length of each curtain rod will be 1.00m to 1.80m long) complete all as directed and specified.

S & F in repair 100mm dia (bore of pipe) cast iron (sand cast) soil, waste, vent pipe in any length with or without ears with cement joint fixed to walls, complete all as specified.

S&F in repair Gun-metal globe or gate valves 20mm bore with iron wheel head, screwed both ends for iron iron complete all as specified and directed.

S&F in repair 15 mm dia Ball brass valves, high pressure, with polythene float and fly- nut com-plete, scre-wed for iron pipe or brass ferrule , plastic ball screwed for iron pipe and fixed complete all as specified and directed.

S&F in repair Brass connection 15 mm bore and 45cm long with washers complete all as specified and directed.

S&F in repair cast iron floor trap square type with Cockrooch Proofing CP grating with or without hole including provision of jointing to waste pipes in run lead joint dia of outlet 75 mm, complete all as specified.

S & F in repair 32/40mm dia waste pipe 610mm long suitable for WHB or Sinks etc complete all as specified and directed by Engineer-in-Charge

S & F in repair 100 mm dia (bore of pipe) cast iron (sand cast) soil, waste, vent pipe in any length with or without ears with cement joint fixed in trenches, complete all as specified.

S & F in repair 75 mm dia (bore of pipe) cast iron (sand cast) soil, waste, vent pipe in any length with or without ears with cement joint fixed to walls and trenches, complete all as specified.

S & F in repair 50 mm dia (bore of pipe) cast iron (sand cast) soil, waste, vent pipe in any length with or without ears with cement joint fixed to walls and trenches, complete all as specified.

S&F 100mm dia (bore of pipe) cast iron Tee diminishing pieces or tapers (larger bore measured) with cement joints, complete all as specified.

All as per item 99 but 75mm dia (bore of pipe) Tee

All as per item 99 but 50mm dia (bore of pipe) Tee

S & F 75mm dia (bore of pipe) branch pieces single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches, fitted with oval access door, complete all as specified.

All as per item 102 above but 100mm dia (bore of pipe).

S&F in repair 100 mm pipe, stack clamps out of 50mmx 5 mm flat iron and 16 mm dia round iron stamp including bolts and nuts and securing ends of stays to walls or roof complete all as specified and directed.

All as per item No 106 above but 75 mm bore pipe.

Supply only liquid water proofing compound complete all as specified and directed.

M&L for providing pre cast cement concrete jallies, 50mm thick type BO, 1:2:4 (12.mm graded stone agg) set in cment mortar 1:4 incl all moulding complete all as specified

M&L for glossy finish chequered cement concrete tiles 30cm x 30cm x 25mm thick in floors etc set and jointed in neat cement slurry and jointed in white/coloured cement to match over and including 20 mm thick screed bed in cement mortar in (1:6) complete all as specified and as directed by Engr-in-charge.

Fabrication & fixing of kitchen cabinet & wardrobe/cupboard made out of 15 to 18 mm thick PVC board laminated sheet including providing cabinet for keeping/basket/cutlery basketwith handles complete Make: Rajshree or equivalent all as spd and approved by Garrison Engineer.

Supply only Stainless steel basket (plain) of size 50cmx37cmx10cm made of 4mm th S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18'/20' length two way extruded MS galvanised over rollers of approved Make: Life style Cat part No WA/POB/15204 or equivalent as approved by GE

Supply only Stainless steel thali basket (11-13 division) of size 50cmx37cmx20cm made of 4mm th S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18'/20' length two way extruded MS galvanised over rollers of approved Make: Life style Cat part No WA/TB/15208 or equivalent as approved by GE

Supply only Stainless steel Plate basket (11-13 division) of size 50cmx37cmx16cm made of 4mm th S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18'/20' length two way extruded MS galvanised over rollers of approved . Make: Life style Cat part No WA/PTH/15206 or equivalent as approved by GE

Supply only Stainless steel Partition basket of size 50cmx37cmx16cm made of 4mm th S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18'/20' length two way extruded MS galvanised over rollers of approved make Make: Life style Cat part No WA/PRT/17206 or equivalent as approved by GE

Supply only Stainless steel Cutlary basket of size 50cmx37cmx10cm made of 4mm th S.S.wire and bottom of S S perforated sheet approved quality with suitable arrangement for fixing Telescope basket (channel) 18'/20' length two way extruded MS galvanised over rollers of approvedMake: Life style Cat part No WA/CUT/15204 or equivalent as approved by GE

Supply only Stainless steel basket (plain) of size 50cmx37cmx16cm made of 4mm th S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18'/20' length two way extruded MS galvanised over rollers of approved Make: Life style Cat part No WA/POB/15206 or equivalent as approved by GE

Supply only Stainless steel bottol full out of size 50cmx40cmx16cm in two tier made of 4mm th S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18'/20' length two way extruded MS galvanised over rollers of approved make Make: Life style Cat part No FF/BPO/62018 or equivalent as approved by GE

Supply only Stainless steel basket (plain) of size 50cmx52cmx16cm made of 4mm th S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18'/20' length two way extruded MS galvanised over rollers of approved make Make: Life style Cat part No WA/POB/21206 or equivalent as approved by GE

Supply only Stainless steel grid basket (plain) of size 50cmx52cmx20cm made of 4mm th S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18'/20' length two way extruded MS galvanised over rollers of approved make Make: Life style Cat part No WA/POB/21208 or equivalent as approved by GE

S&F Brass Mortice lock (4 Lever),vertical type, size 100 mm complete all as specified and directed by Engr-in-Charge.

S&F Magnet ball catcher brass body with 8mm dia steel ball of approved qualities complete all as specified

S&F 150mm long Hasp and staple , safety type, Aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws

S&F 35mm thick 2nd class hard wood glazed and sekeleton shutter's open rebated prepare to receive glass gouge etc edges of framing plain chamfered or ronded fitted with cut and mitered bead's for securing glass gauge etc size of marker of shutters as per SSR Part-I sec-8 clause 8.2(a).

S&F Plain , solid , straight chowkhats and frames of 2nd class hard wood, wrought , framed rebated on the solid , rounded or chamfered , put together with glue, pinned at joints, supplied and fixed.

S&F 100mm long butt Hinges, medium weight, cold rolled mild steel complete

S&F 300mm long aluminum alloy anodized sliding door bolt with hasp and staple(bolt type)and fixing clips of sheet cast sec and fixing bolts and sliding bolts of extruded sec or cast aluminum alloy and fixed all as spd and directed.

S&F 200 mm long aluminum anodized barrel tower bolt of cast aluminiun alloy section and fixed all as spd and directed.

S&F Extruded Aluminium alloy handles, 150mm size cast type anodised complete all as specified and directed

S&F for Brass 300 mm long, ordinary rat tail rod pattern springs including roller and roller plate complete

S&F for Floor door stoper of aluminium alloy body with hard drawn steel spring 140mm long.

M&L Resecuring or Easing and adjusting , without taking down shutters of doors/windows for easy opening /closing ,tightening of hinges and changing its position or adjustment of tower bolts/sliding bolts etc area not exc 2 sqm each complete all as specified and directed.

Material and labour for APP polymaric water proofing membrene minimum 3mm thick and weighting not less than 3.6 kg / sqm of make 'Moply FP' manufactured by STP Texsa Ltd or' Hyper Plas' ( polyster) manufactured by M/S IWL Ltd or'Shaliplas' (polyster) manufactured by M/S Capital Steels and chemicals Pvt Ltd or 'Mak polyplast' manufactured by M/S M K Petro as approved by GE , black finished reinforced with non weven polyster matt,with fusable inish laid over compatable bitumen primer at the rate of 0.40 Ltr/Sqm torching overlaps with a propane or abutane gas torch, with f a over lap of 75mm at the sides and100 at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufactur's instructions including 0.40 Ltr/Sqm torching overlaps with a propane or abutane gas torch, with f a over lap of 75mm at the sides and100 at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufactur's instructions including preparation of surface,including complete removal of existing treatment and the make the surface good for new application complete all as specified and as directed. Note : The water proofing treatment shall be carried out by the manufacturer or their authorised applicators.

M&L for Italian marble of any shade other than white and black 18- 20 mm thick ( table rubbed and polished ) in steps, Jambs,pillars, Cooking platform, floor and like in cement mortar (1:4) including pointing in white cement ( 1:2) using marble dust with admixture of pigment to match with marble laid over 20mm thik screed bed in CM 1:6 , bedded, jointed and pointed with grey cement slurry including cutting and polishing complete all as specified and directed.

M&L for italian marble of any shade other than white and black 18- 20 mm thick ( table rubbed and polished ) in steps, Jambs,pillars, and like in cement mortar 10mm in CM (1:4) including pointing in white cement ( 1:2) using marble dust with admixture of pigment to match with marble laid o bedded, jointed and pointed with grey cement slurry including cutting and polishing complete all as specified and directed.

S&f stainless Steel (S-304) work as in tubular pipe such purlins and rafter,balluster for railing work etc fixed with suitable arrangement as required complete all as specified and as directed.

M&L for 10 mm thick tinted toughned glass (Designer type) for steel railing work including all fitting and acceessories with stainless steel brackets, as per approved design complete all as specified.

S&F for waste fitting 40mm dia , CP for WHB with long screwed shunks and nuts complete all as spd and directed

S&F for waste coupling 32mm dia , CP for sink with long screwed shunks and nuts complete all as spd and directed

M&L for MDF cladding of pre-laminated 80mm thk board duly fixed to walls as per drawings or as directed by Engineer in charge at site.

M&L for 6 mm Plywood, grade BWR,type BB, fixe with screws on timber plugs on wall surfaces complete all as specified and as directed by Engr-in-Charge.

M&L for 2nd class hard wood exc 13& n exc 25 sqcm plain fillets,square rectangular in clean sawn secured bull nose,chamfered or rounded on one edge or face with nail complete all as specified and as directed by Engr-in-Charge.

M & L for 6mm thick and 19/20 mm wide wrought teak wood lapping fixed with screws to pre-laminated particle board incl necessary polishing /painting complete all as specified and directed by Engr-in-Charge.

S&F for L- Bihari hinges,Stainless steel, 15 crank/degree, with nickel finish colour, all completed as specified and directed

S&F oval type Brass handles, cast type,polished bright 150mm size.

M&L for 100mm Brass barrel tower bolts ISI marked with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and directed by Engr-in-Charge.

M&L for Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc including dismantling of old sheet of any description complete all as specified and directed by Engr-in-Charge.

M&L PVC pipe in repair 110mm bore single socketed in any length with rubber ring joints complete all as specified and directed by Engineer- In- charge.

M & L PVC bend in repair 110mm bore any radius complete all as specified and directed by Engineer- In- charge.

S&F stainless steel peg set of six (Designer type) complete all as specified and directed fixed complete.

S&F for Glass Brick/block of size 190x190x80 mm work in approved colour,texture and form with straight or curved on plan to any radious in any description of wall including all necesaarry fitting,jointing,laying,formwork glazing clip,putty etc complete all as specified and directed.etc complete all as specified and directed.

S&F for Glass Brick/block of size 190x90x80 mm work in approved colour,texture and form with straight or curved on plan to any radious in any description of wall including all necesaarry fitting,jointing,laying,formwork,glazing clip,putty etc complete all as specified and directed.

M&L for POP cornise of size exc 20Sqcm but not exc 50 Sqcm of approved design of multiple level on ceiling to flat surface over /concrete surface moulding as in cornices, and the like the same complete all as specified.

M&L for preparation of new/old plastered surface of wall and applying two coat of Designer wall paper roll /Texture paint (Approved Design and colour) over a coat of priming coat including 2-3 mm thick wall care putty on newly/old plastered surface over plaster of paris putty of 2 mm thickness incl removal of existing treatment on surfaces of walls by scrapping down with mechanical grinder complete all as specified and directed.

Taking down cement plaster / duster bed PCC of Column, chajja, Parapets of roof, facia, drops etc and making good with cement plaster 10mm thick in CM 1:3 with PCC 1:2:4, (average thickness of PCC 25mm) as required, brushing neat cement slurry with 3.0kg of cement per sq. metre including necessary form work and scaffolding upto 4th floor including fixing of wire netting where required to match the existing surfaces complete all as specified.

S&F for fabric panels 50mm thickness, core material glasswool, high efficiency sound absorption, NRC 1.0, spandex material, in any description of wall including all necesaarry GI Studs, 12mm rail system,, and screws etc complete all as specified and directed.etc complete all as specified and directed. (Make: Armstrong, Veils, Hunter Douglas, Ecophone

M&L For MDF Cladding of pre-laminated 80mm thk board duly fix on 600mm x 600mm hardwood grid fix to walls as per drawings and engineer in charge. (Make: Greenply, Centuryply, Veils, Virgo)

M&L for cement concrete 1:3:6 type D2 (using 40mm graded agg)incl packing under and haunching against the sides for 150mm internal dia class NP2 pipes after they are laid and tested complete all as specified (thickness of concrete bed 150mm).

Supply and laying Reinforced concrete pipes 150mm dia, class NP2, laid and jointed complete with collars incl testing and laid in trenches to a level on concrete bed complete all as specified.

M&L Brick work using sub class’B’ bricks in CM ( 1:4) straight or curved on plan exc 6 mtr mean radius complete all as specified.

Cutting into existing manholes for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 or 3/4 section ) in cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate finished smooth and reforming benching as required for 150/200mm dia pipes complete all as specified and directed.

S&F Precast plastic fibre reinforced concrete man hole covers" medium duty " of overall size 1000 mm x 500 mm x 75 to 80 mm factary made complete all as specified and directed.

M&L for providing PCC 1:2:4 type B2 in surface channels and drains (using 20 mm graded crushed stone aggregate ) complete all as specified & directed.

M&L Cement concrete 1:2:4 type B0(using 12.5mm graded crushed stone aggregate) as in bed blocks for hold fast, coping, benching etc. including weathering, slightly rounded or chamfered angles or throating including form work to concrete surfaces complete all as specified and directed upto two storey height.

Dismantling of floor of EWC type Water closet area, Bath area, Kitchen area and removing out the cinder/concrete from sunken portion, cleaning of RCC surface to remove dust loose particle with compressed air or any othe suitable method depending on site conditions, grinding any sharp edges etc complete all as specified and directed. (a) Cleaning of RCC surface to remove dust, loose particle etc with compressed air or any other particles or any other suitable techniques on site conditions etc. (b) M&L for a glass fibre reinforced acrylic modified cementitious coating system with base coat of Sika Top & Seal-107 @ 1.50 Kg/Sqm glass fibre reinforcement Sika® Fab-I and top coat with Sika Top® Seal 107 @ 1.5 Kg/Sqm or equivalent of Fosroc or Pidilite. (c) M&L for protection plaster 15mm thick on cement mortar 1:3 admixed with appropriate integral water proofing compound with Sika® Plastocrete plus as specified. (d) M&L for providing 25mm dia GI pipe spout projecting at least 150mm beyond outer face of wall. (e) M&L for sunken portion filled with 40mm graded brick bats and finished with 50mm thick PCC 1:2:4 type B1 all as specified and directed. (f) The area of Each WC portion, kitchen, bath is n.exc 4.00 Sqm each. (h) Cost of the above aspect shall be deemed to be included in the quoted rates of the respective item and nothing extra shall be paid on.

Taking down carefully old unserviceable copper/aluminium point wiring From existing conduit / batten type (light, fan, socket or power point) complete such as switches, ceiling rose, pendent holder, regulator and socket etc are to be measured seperately and making good the disturbed surface of wall / floor/ ceiling etc as original i.e. brick work, plastering, white washing etc complete all as directed.

M&L in replacement for point wiring complete with 1.5 Sq mm (nominal area) FRLS, PVC insulated un-sheathed and stranded copper conductor cable ISI marked and including PVC concealed conduit ISI marked of size 20 mm dia medium grade and PVC conduit fittings such as tees, bends, elbow, reducers except conduit junction box (junction box will be of MS) including FRLS, PVC insulated unsheathed 1.5 Sqmm copper earth wire, connecting to common earth dolly with and incl Metal flush box of suitable size for fixing modular switches/sockets/fan regulator etc , with and including Modular cover plates of suitable size and making good surface as original by plastering, whitewash/colour and distemper etc complete all as directed for the following :-(Note : The cost of modular type Metal boxes and modular accessories like cover plates will be included in quoted rate.):

(a) one light point / fan point/ wall fan point/ bell/ buzzer controlled by one 1-way switch/ bell push.

(b) one socket outlet point 5 amps on the same board.

(c) one socket outlet point 5 amps on the independent board.

(d) All as per srl item no. 165 here-in-before but with 2.5 sq mm FRLS copper wire with 1.5 Sqmm FRLS copper earth wire for 15 Amp Socket outlet point. Note : The point wiring for power point will not be mixed with light/fan point circuit or not in the same conduit pipe.

M&L in replacement for TV Wiring with Co axial RG-6 heavy duty PVC insulated, PVC sheathed cable having single strand of 0.7 mm dia taped suitable for telephone wiring and making all necessary connections from terminal box to TV socket, drawn in and including separate concealed PVC conduit complete all as directed.

M&L in replacement of telephone Wiring with twin core PVC insulated, PVC sheathed cable suitable for telephone wiring and making all necessary connections from terminal box to telephone socket, drawn in and including separate concealed PVC conduit complete all as specified and directed.

S&F in replacement for Modular switch 6 Amp, 1 way, 1 module size complete all as directed.

S&F in replacement for Modular Bell push 6A 1 module complete all as directed.

S&F in replacement for Modular switch 16 Amp, 1 way, 1 module size with indicator lamp complete all as directed.

S&F in replacement for of Modular socket 6 Amp, 2 & 3 pin, universal type, 2 module size complete all as directed.

S&F in replacement for Modular socket 16 Amp multipurpose shuttered type, 2 module size with indicator lamp complete all as directed.

S&F in replacement of Modular Fan regulator step type, 120 watts, 2 Module size complete all as directed.

S&F in replacement of Call bell ding dong type, AC, 230V complete all as directed.

S&F in replacement of Modular TV socket) 01 Module size socket as per site requirement complete all as directed by the Engr-In-Charge.

M&L in replacement of Modular Telephone socket Jack 01 Module size (RJ 11 Socket Jack) complete with modular sheet as per site requirement complete all as directed by the Engr-In-Charge.

Supply and fixing in replacement of Ceiling rose, insulated body, 3 terminal, 240 volts, 5 Amps and making good surface as original by plastering and whitewash/ colour/ distemper etc complete all as directed.

Supply and fixing in replacement of LED tube light fitting 22 W to wall mounting type with and including all electric connections with two core PVC insulated, PVC sheathed copper conductor flexible cable complete all as specified.

S&F in replacement of LED Mirror light 10/12 Watt complete all as specified and directed.

S&F in replacement of Decorative wall mounted LED Light fitting including 10W LED bulb all as specified and directed.

S&F in replacement of LED Bed Side Flexible Arm lamp 3/5W complete all as specified and directed.

S&F in replacement of LED Surface mounted Square/Round downlight with AL die-cast body, finish with drop down PC diffuser to deliver low glare illumination with optimized heat sink for efficient heat dissipation. 12/15W incl making electric connection complete all as directed.

S&F LED street light fittings 45W LED suitable for building security light, pressure diecast aluminium roadway luminaire with high power LEDs and HF electronic driver complete including all electric connecions with fixing on wall with nut, bolt, washar, clamps etc complete all as directed.

Supply and fixing security light fitting bracket, 1.5 mtr long made out of galvanized iron pipe of 40 mm dia size light grade complete with nut, bolts, washer etc inclusive of one primer coat, one under coat and one finishing coat of silver paint complete all as directed.

S&F in replacement ventilation (exhaust) fan 250mm sweep made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding including hole arrangement in window/wall of suitable size complete all as specified and as directed.

Taking down geyser of 25/35 lts capacity and refixing the same after repairing unsv item.(Note : Replacement of unsv item will be measured and paid separately)

S&F in replacement of Thermostate for geyser of 25/35 lts capacity

S&F in replacement of Element 1.5/2 KW for geyser

S&F in replacement CP flange connection pipe with brass/SS nuts for geyser

Taking down ceiling fan 1200/1400mm and refixing with new twisted flexible wire the same after repairing unsv item (Note : Replacement of unsv item will be measured and paid separately)

S&F in replacement of capacitor 2.5/3.15 mfd for ceilig fan 1200/1400mm

M&L for rewinding for ceiling fan 1200/1400mm with super enamelled copper winding wire of required size duly varnishing, greasing,oiling and replacement of unsv bearing complete all as specified and directed.

M&L in replacement for Sub main wiring with 2 run of 10.0 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked, drawn in and including to separate PVC concealed conduit 25 mm dia with and including 10.0 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire, connected with thimble from main DB to sub main DB complete all as directed.

M&L in replacement for Sub main wiring with 2 run of 6 .0 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked, drawn in and including to separate PVC concealed conduit 25 mm dia with and including 6.0 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire, connected with thimble from main DB to sub main DB complete all as directed.

S&F in replacement of Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, surface mounting, SPN 08 way, 240 volts with bus bar rating 200 Amps including dust and vermin proof and making all necessary connections complete all as directed.

S&F in replacement of Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, surface mounting, SPN 04 way, 240 volts with bus bar rating 200 Amps including dust and vermin proof and making all necessary connections complete all as directed.

S&F in replacement of Distribution Board single door made out of CRCA mild steel sheet surface mounting SPN 02 way, 240 volts without bus bar complete all as directed.

S&F in replacement of Modular AC Box, SPN type with 3 pin plug and socket with and including one MCB SPN, C Curve type of capacity 20/25 Amp, 10 kA complete all as directed.

Supply and fixing in replacement of MCB SP, C Curve type, 10 KA, 10 to 32 Amp, with over load and short circuit protection complete all as directed.

Supply and fixing in replacement of MCB SPN C Curve type, 10 KA, 40 to 63 Amp, with over load and short circuit protection complete all as directed.

S&F in replacement of Key Switch 2/3Module 32A DP unit switch with key tag complete all as directed.

S&F in replacement of MCCB Incommer Distribution Board double door, TPN 4Way, 415V, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, surface/recess mounting, with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc and making all necessary connections complete all as directed.

M&L in replacement for earthing complete with GI earth plate electrode 600 mmx 600mm x 6mm thick burried directly in ground not less than 2.25 mtrs below ground level, with top edge of the plate not less than 1.5 mtrs deep below normal ground level, connected to galvanised earth wire 4mm by means of bolts, nuts check nuts to earth test point including necessary PCC 1:2:4 type B-1 pit, cover frame, GI pipe 15mm dia light grade for protection of earthing lead and GI pipe 20 mm dia for watering pipe with funnel, wire mesh, salt, charcoal dust and excavation complete all as directed.

S&F in replacement of MCCB 4P 160 Amp Adjustable type with breaking capacity 36 KA suitable for 415 volts AC supply, with over load and short circuit protection complete all as specified.

M&L for taking down electronic energy meter single phase and refixing the same with new connection wiring complete all as specified and as directed.

S&F ceiling fans 1200mm sweep complete with blades, down rods, flexible cable and accessories, 230 V, Min air delivery 210 CFM with service value 6.00 BEE. Five star rated complete all as specified and as directed.

S&F electric water heater of capacity 25 litre, storage type steel tank with glass inner lining and heating element upto 2 KW BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. complete all as specified and as directed.

S&F wall mounted fan 300mm sweep, AC, single Phase. 230V with blades complete all as specified and as directed.

S&F exhaust fan 300mm sweep, steel body AC single Phase. 230V with, blades, and frame and louvers including hole arrangement in window/wall of suitable size complete all as specified and as directed.

imran construction company