Strengthening, fabrication and installation of D11 gate- II and gate- I for distributary no. D11from main Ranbir canal at RD 40350, fabrication and installation of D12 gate for distributary no. D12 from main Ranbir canal at RD 43744, fabrication and

strengthening, fabrication and installation of D11 gate- II and gate- I for distributary no. D11from main Ranbir canal at RD 40350, fabrication and installation of D12 gate for distributary no. D12 from main Ranbir canal at RD 43744, fabrication and installation of Pandorian head gate-II on main Ranbir canal at RD 52134, fabrication and installation of leaf of gate at Pandorian escape gate- II on main Ranbir canal at RD 52134.

I) Strengthening, fabrication and installation of D11 gate- II for distributary no. D11 from main Ranbir canal at RD 40350 by way of dismantling ofgate lifting mechanism from the supporting channel and disconnecting the stem rod from the leaf structure then extracting out the damaged/worn out gate leaf structure with the help of manual labour using tools and tackles, chain pulley block and tripod/hydra crane after removing accumulated mud/silt around the gate leaf. Carriage of gate structure along with spindle type winch machine and stem rod to the road with the help of manual labour using tools and tackles. Loading in mechanical transport and then carriage to workshop. Increasing the height of gate by way of providing, fitting and fabrication of frame from ISMB 100 channel over the existing channel to support the winch machine. Drilling of holes in channels as per the profile of winch machine. Increasing the height of the supporting channel by 12 inches approx. by way of grouting the supporting channel in concrete in ratio of 1:3:6. Fabrication of new leaf structure with increased height of size 53 inches x 60 inches(approx) using the ISMC 75x 50 mmchannel or angle ironwith 4 number vertical & 3 numberhorizontal cross members for support by way of cutting /welding using superior quality electrodes. The leaf of the gate should have fivenumber vertical supports and horizontal supports welded together to form the frame. The MS sheet of 5 mm thickness needs to be welded over the fabricated frame of ISMC 75 channel. Making of provision for stem rod attachment with 2 no. L-shaped MS Clamps. Providing, fabrication and fitting of 1 no. stem rod out of MS bar of length as per increased length and site conditionsand thenturning, threading, finishing to the original size. Fabrication, providing & fitting of 02/03 ton capacity manually operated, worm gear type winch machine along with base plate of 8/10mm thickness after replacing damaged spindle type winch machine.Oiling and greasing the gear and bearings mechanism before fitting. Providing and fitting of rain pipe over the winch machine to secure the stem rod and machinery. Loading the gate structure along with winch machine on the carriage vehicle for carrying to site of installation. Unloading the gate structure at road side then shifting to the site of installation. Installation of gate structure by way of lowering the leaf structure into the sliding grooves using manual labour, tools and tackles using chain pulley block and tripod/crane. Drilling requisite number of holes in hoisting channels at site. Fitting of winch machine on the supporting channel and connecting the stem rod to the leaf structure after ensuring the proper alignment/gravity of the gate structure. Complete painting of gate structure with coats of red oxide primer and superior quality enamel paint ( Asian paints/ KansaiNerolac paints/ Berger paints) with proper colour code of blue and black paint. Complete job includes cost of material, transportation charge, labour charges and testing for its smooth operation at site, cost of sand bags for stopping the flow of water in escape channel during the period of execution of work. The firm should quote the rates after giving the rebate on old scrap. Note:- The tenderers are requested to visit the site and quote the rate as per site conditions. Any modifications/ alterations of the job, absolutely necessary if required at the time of execution may be done as per actual site conditions. II) Strengthening, fabrication and installation of D11 gate-I for distributary no. D11 from main Ranbir canal at RD 40350 by way of dismantling of gate lifting mechanism from the supporting channel and disconnecting the stem rod from the leaf structure then extracting out the damaged/worn out gate leaf structure with the help of manual labour using tools and tackles, chain pulley block and tripod/hydra crane after removing accumulated mud/silt around the gate leaf. Carriage of gate structure along with spindle type winch machine and stem rod to the road with the help of manual labour using tools and tackles. Loading in mechanical transport and then carriage to workshop. Increasing the height of gate by way of providing, fitting and fabrication of frame from ISMC 100 channel/ ISMB girder over the existing channel to support the winch machine. Drilling of holes in channels as per the profile of winch machine. Increasing the height of the supporting channel by 12 inches approx. by way of grouting the supporting channel in concrete in ratio of 1:3:6. Fabrication of new leaf structure with increased height of size 52 inches x 60 inches (approx) using the ISMC 75x 50 mm channel or angle iron with 4 number vertical & 3 number horizontal cross members for support by way of cutting /welding using superior quality electrodes. The leaf of the gate should have three number vertical supports and horizontal supports welded together to form the frame. The MS sheet of 5 mm thickness needs to be welded over the fabricated frame of ISMC 75 channel. Making of provision for stem rod attachment with 2 no. L-shaped MS Clamps. Providing, fabrication and fitting of 1 no. stem rod out of MS bar of length as per increased length and site conditions and then turning, threading, finishing to the original size. Loading the gate structure along with winch machine on the carriage vehicle for carrying to site of installation. Unloading the gate structure at road side then shifting to the site of installation. Installation of gate structure by way of lowering the leaf structure into the sliding grooves using manual labour, tools and tackles using chain pulley block and tripod/crane. Drilling requisite number of holes in hoisting channels at site. Fitting of winch machine on the supporting channel and connecting the stem rod to the leaf structure after ensuring the proper alignment/gravity of the gate structure. Complete painting of gate structure with coats of red oxide primer and superior quality enamel paint ( Asian paints/ Kansai Nerolac paints/ Berger paints) with proper colour code of blue and black paint. Complete job includes cost of material, transportation charge, labour charges and testing for its smooth operation at site, cost of sand bags for stopping the flow of water in escape channel during the period of execution of work.The firm should quote the rates after giving the rebate on old scrap. Note:- The tenderers are requested to visit the site and quote the rate as per site conditions. Any modifications/ alterations of the job, absolutely necessary if required at the time of execution may be done as per actual site conditions. III) Fabrication and installation of D12 gate for distribution of D12 canal from main Ranbir canal at RD 43744 by way of dismantling of damaged old spindle type gate lifting mechanism from the supporting channel and disconnecting the stem rod from the leaf structure then extracting out the damaged/worn out gate leaf structure with the help of manual labour using tools and tackles, chain pulley block and tripod/hydra crane after removing accumulated mud/silt around the gate leaf. Carriage of gate structure along with spindle type winch machine and stem rod to the road with the help of manual labour using tools and tackles. Loading in mechanical transport and then carriage to workshop. Fabrication of leaf structure of size 60 inches x 30 inches (approx) using the ISMC 75x 50 mm channel or angle iron with vertical & horizontal cross members for support by way of cutting /welding using superior quality electrodes. The leaf of the gate should have three number vertical supports and horizontal supports welded together to form the frame. The MS sheet of 5 mm thickness needs to be welded over the fabricated frame of ISMC 50 channel or angle iron. Making of provision for stem rod attachment with 2 no. L-shaped MS Clamps. Providing, fabrication and fitting of 1 no. stem rod MS bar of length as per the site conditions and then turning, threading, finishing to the original size. Fabrication of outer frame to support the winch machine and load of gate during up and down movement of gate. The outer frame of D12 gate consists of grove fabricated in concrete and installation of 5 inch MS channel or I section over the grooves for movement of gate. The length of girder/ channel should be 6 ft approx. holes should be drilled on channel/ girder as per the winch machine. Then outer structure of the gate have to be fitted in walls of concrete structure with cement and concrete mixture minimum ratio of 1:3:6. Fabrication, providing & fitting of 02/03 ton capacity manually operated, worm gear type winch machine along with base plate of 8/10mm thickness after replacing damaged spindle type winch machine. Oiling and greasing the gear and bearings mechanism before fitting. Providing and fitting of rain pipe over the winch machine to secure the stem rod and machinery. Loading the gate structure along with winch machine on the carriage vehicle for carrying to site of installation. Unloading the gate structure at road side then shifting to the site of installation. Installation of gate structure by way of lowering the leaf structure into the sliding grooves using manual labour, tools and tackles using chain pulley block and tripod/crane. Drilling requisite number of holes in hoisting channels at site. Fitting of winch machine on the supporting channel and connecting the stem rod to the leaf structure after ensuring the proper alignment/gravity of the gate structure. Complete painting of gate structure with coats of red oxide primer and superior quality enamel paint ( Asian paints/ Kansai Nerolac paints/ Berger paints) with proper colour code of blue and black paint. Complete job includes cost of material, transportation charge, labour charges and testing for its smooth operation at site, cost of sand bags for stopping the flow of water in escape channel during the period of execution of work.The firm should quote the rates after giving the rebate on old scrap. Note:- The tenderers are requested to visit the site and quote the rate as per site conditions. Any modifications/ alterations of the job, absolutely necessary if required at the time of execution may be done as per actual site conditions. IV) Fabrication and installation of Pandorian head gate- II on main Ranbir canal at RD 52134 by way of dismantling of damaged old gate lifting mechanism from the supporting channel and disconnecting the stem rod from the leaf structure then extracting out the damaged/worn out gate leaf structure with the help of manual labour using tools and tackles, chain pulley block and hydra crane after removing accumulated mud/silt around the gate leaf. Carriage of gate structure along with winch machine and stem rod to the road with the help of manual labour using tools and tackles. Loading in mechanical transport and then carriage to workshop. Fabrication of leaf structure of size 84 inches x 66 inches (approx, size can vary by +- 10 percent) using the ISMC 100 channel size with vertical & horizontal cross members for support by way of cutting /welding using superior quality electrodes. The leaf of the gate should have three number vertical supports and four number horizontal supports welded together to form the frame. Stiffeners must be welded at the centre supports to support the force and load on welding joints. The MS sheet of 5/6 mm thickness needs to be welded over the fabricated frame of ISMC 100 channel. Making of provision for stem rod attachment with 2 no. L-shaped MS Clamps with provision of connecting to stem rod with two number nuts and bolts for load sharing. Providing, fabrication and fitting of 1 no. stem rod out of 60 mm MS bar of length as per the site conditions (12 ftapprox) and then turning, threading, finishing to the original size. Fabrication, providing & fitting of 05/07 Ton capacity manually operated, worm gear type winch machine along with base plate of 16 mm thickness. Oiling and greasing the gear and bearings mechanism before fitting. Providing and fitting of rain pipe over the winch machine to secure the stem rod and machinery. Loading the gate structure along with winch machine on the carriage vehicle for carrying to site of installation. Unloading the gate structure at road side then shifting to the site of installation. Installation of gate structure by way of lowering the leaf structure into the sliding grooves using manual labour, tools and tackles using chain pulley block and tripod/crane. Drilling requisite no. of holes in hoisting channels at site if necessary due to misalignment. Fitting of winch machine on the supporting channel and connecting the stem rod to the leaf structure after ensuring the proper alignment/gravity of the gate structure. Complete painting of gate structure with coats of red oxide primer and superior quality enamel paint ( Asian paints/ Kansai Nerolac paints/ Berger paints). Complete job includes cost of material, transportation charge, labour charges and testing for its smooth operation at site, cost of sand bags for stopping the flow of water in escape channel during the period of execution of work. The bidder should quote rates including the rebate on old scrap. Note:- The tenderers are requested to visit the site and quote the rate as per site conditions. Any modifications/ alterations of the job, absolutely necessary if required at the time of execution may be done as per actual site conditions. V) Fabrication and installation of Pandorianescape gate- II on main Ranbir canal at RD 52134 by way of dismantling of gate lifting mechanism (rack and pinion type winch machine) from the supporting channel and disconnecting the rack from the leaf structure then extracting out the damaged/worn out gate leaf structure with the help of manual labour using tools and tackles, chain pulley block and hydra crane after removing accumulated mud/silt around the gate leaf. Carriage of gate structure along with winch machine and stem rod to the road with the help of manual labour using tools and tackles. Loading in mechanical transport and then carriage to workshop. Fabrication of leaf structure of size 108 inches x 48 inches (approx, size can vary by +- 10 percent) using the ISMC 100 channel size with vertical & horizontal cross members for support by way of cutting /welding using superior quality electrodes. The leaf of the gate should have four number vertical supports and three number horizontal supports welded together to form the frame. Stiffeners must be welded at the centre supports to support the force and load on welding joints. The MS sheet of 5/6 mm thickness needs to be welded over the fabricated frame of ISMC 100 channel. Making of provision for double rack attachment to leaf of the gate with 2 no. L-shaped MS Clamps across the width of leaf. Loading the gate structure along with winch machine on the carriage vehicle for carrying to site of installation. Unloading the gate structure at road side then shifting to the site of installation. Installation of gate structure by way of lowering the leaf structure into the sliding grooves using manual labour, tools and tackles using chain pulley block and tripod/crane. Fitting of rack and pinion type winch machine over the supporting channels by completely assembling the winch machine and greasing all the moving parts. Complete painting of gate structure with coats of red oxide primer and superior quality enamel paint ( Asian paints/ Kansai Nerolac paints/ Berger paints) with proper colour code of blue and black. Complete job includes cost of material, transportation charge, labour charges and testing for its smooth operation at site, cost of sand bags for stopping the flow of water in escape channel during the period of execution of work. The bidder should quote rates including the cost of old scrap. Note:- The tenderers are requested to visit the site and quote the rate as per site conditions. Any modifications/ alterations of the job, absolutely necessary if required at the time of execution may be done as per actual site conditions.

Fabrication and installation of Changia minorgate on D17 distributary of main Ranbir canal at RD 7800 and fabrication and installation of Rattian minor gate on D10 distributary canal of main Ranbir canal at RD 4170 of D10 installed before Rattian head gates.

Fabrication and installation of Changia minor gate on D17 distributary of main Ranbir canal at RD 7800. Fabrication of leaf structure of size 18 inches x 30 inches(approx) using the angle iron 40 mm size with vertical &horizontal cross members for support by way of cutting /welding using superior quality electrodes. The leaf of the gate should have twonumber vertical supports on both sides and three number horizontal supports welded together to form the frame. The MS sheet of 4/5 mm thickness needs to be welded over the fabricated frame. Making of provision for stem rod attachment with 2 no. L-shaped MS Clamps. Providing, fabrication and fitting of 1 no. stem rod MS bar of length as per the site conditionsand thenturning, threading, finishing to the original size as per the internal threading’s on gear. Fabrication of outer frame 24 inch x 60 inch of gate for up and down moment of gate using ISMC 75 channel. The outer frame should consists of two side channels for up and down moment of gate, bottom sil beam and two channels on top to support the weight of winch machine and gate. The job consists of dismantling of fabrication of grooves as per size of ISMC 75 channel in concrete structure.Then outer structure of the gate have to be fitted in walls of channel with cement and concrete mixture minimum ratio of 1:3:6. Fabrication, providing & fitting of 02 Ton capacity manually operated, worm gear type winch machine along with base plate of 6/8mm thickness.Oiling and greasing the gear and bearings mechanism before fitting. Providing and fitting of rain pipe over the winch machine to secure the stem rod and machinery. Loading the gate structure along with winch machine on the carriage vehicle for carrying to site of installation. Unloading the gate structure at road side then shifting to the site of installation. Installation of gate structure by way of lowering the leaf structure into the sliding grooves using manual labour, tools and tackles using chain pulley block and tripod/crane. Drilling requisite no. of holes in hoisting channels at site. Fitting of winch machine on the supporting channel and connecting the stem rod to the leaf structure after ensuring the proper alignment/gravity of the gate structure. Complete painting of gate structure with coats of red oxide primer and superior quality enamel paint ( Asian paints/ Kansai Nerolac paints/ Berger paints). Complete job includes cost of material, transportation charge, labour charges and testing for its smooth operation at site, cost of sand bags for stopping the flow of water in escape channel during the period of execution of work if necessary. The firm should quote the rates after giving rebate on old scrap. II) Fabrication and installation of Rattian minor gate on D10 distributary canal of main Ranbir canal at RD 4170 mtr of D10 installed by way of dismantling of damaged old gate lifting mechanism from the supporting channel and disconnecting the stem rod from the leaf structure then extracting out the damaged/worn out gate leaf structure with the help of manual labour using tools and tackles, chain pulley block and tripod/hydra crane after removing accumulated mud/silt around the gate leaf. Carriage of gate structure along with winch machine and stem rod to the road with the help of manual labour using tools and tackles. Loading in mechanical transport and then carriage to workshop. Fabrication of leaf structure of size 39 inches x 36 inches (approx) using the angle iron of 2inch size with vertical & horizontal cross members for support by way of cutting /welding using superior quality electrodes. The leaf of the gate should have vertical supports and horizontal supports welded together to form the frame. The MS sheet of 5 mm thickness needs to be welded over the fabricated frame. Making of provision for stem rod attachment with 2 no. L-shaped MS Clamps. Providing, fabrication and fitting of 1 no. stem rod MS bar of length as per the site conditions and then turning, threading, finishing to the original size. Fabrication of outer frame 60 inch x 66 inch of gate for up and down moment of gate using ISMC 100 channel or angle iron welded together to form channel. The outer frame should consists of two side channels for up and down moment of gate, bottom sil beam and two channels on top to support the weight of winch machine and gate. The job consists of dismantling of fabrication of grooves as per size of ISMC 100 channel in concrete structure. Then outer structure of the gate have to be fitted in walls of channel with cement and concrete mixture minimum ratio of 1:3:6. Fabrication, providing & fitting of 02 Ton capacity manually operated, worm gear type winch machine along with base plate of 8/10 mm thickness after replacing damaged, spindle type winch machine. Oiling and greasing the gear and bearings mechanism before fitting. Providing and fitting of rain pipe over the winch machine to secure the stem rod and machinery. Loading the gate structure along with winch machine on the carriage vehicle for carrying to site of installation. Unloading the gate structure at road side then shifting to the site of installation. Installation of gate structure by way of lowering the leaf structure into the sliding grooves using manual labour, tools and tackles using chain pulley block and tripod/crane. Drilling requisite no. of holes in hoisting channels at site. Fitting of winch machine on the supporting channel and connecting the stem rod to the leaf structure after ensuring the proper alignment/gravity of the gate structure. Complete painting of gate structure with coats of red oxide primer and superior quality enamel paint ( Asian paints/ Kansai Nerolac paints/ Berger paints). Complete job includes cost of material, transportation charge, labour charges and testing for its smooth operation at site, cost of sand bags for stopping the flow of water in escape channel during the period of execution of work. The firm should quote rates including the rebate on old parts. Note:- The tenderers are requested to visit the site and quote the rate as per site conditions. Any modifications/ alterations of the job, absolutely necessary if required at the time of execution may be done as per actual site conditions.

N B Engineering and Electric Works

Rishabh Electricals and Mechanical Works

CHENAB ENGINEERING WORKS

SMART TECH AND CO

CHENAB ENGINEERING WORKS