Open gym at Imam Bargha at Yokma phase II

Amount

Earth work in excavation by manual means over areas (Exceeding 30 em and upto 1.5 mtr in depth, 1.5 mtr in width as well as 10 sqm. on plan) including disposal of excavated earth upto 1 mtr from cutting edge, disposed earth to be levelled and neatly dressed in : All kinds of Soil.

Providing and laying of dry stone solling in horizontal layer inl. Cost of stone.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering- All work upto plinth level.1:3:6 (1 cement: 3 fine sand : 6 graded stone aggregate 40mm nominal size) Crushed

Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement.1:11⁄2:3 (1 cement : 11⁄2 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and fixing of Air Walker with following specification 1. Dimensions (LxWxH): 1100 x 450 x 1300mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. ‘U’ shaped main frame of NB 80mm (G.I.) ‘C’ Class Pipe, Leg Support frame of NB 50mm (G.I.) ‘C’ Class Pipe. 4. Handle frame pipes of NB 32mm (G.I.) ‘C’ Class. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimetres) 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Base plate cover made of virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness, UV resistant and coloured. 9. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury. 10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 11. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 12. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 13. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 14. High tensile steel with galvanized nut bolts are used for assembly. 15. Equipment made to GS Mark, EN16630, DIN 79000, ASTM F3101-15 & ISO 14001 International standard for outdoor fitness equipment. 16. Self-Explanatory stainless steel label fixed on equipment for ease of use

Providing and fixing of Sit up Station(Double) with following specifications: 1. Dimensions (LxWxH): 1600 x 1150 x 650mm 2. Fabricated with main frame of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Main frame of NB 25mm (G.I.) ‘C’ Class Pipe. 4. Leg support of NB 65mm (G.I.) ‘C’ Class Pipe (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimetres) 5. Fixed on its top is back support made of perforated MS sheet of 2mm thickness. 6. All pipes are powder coated using Akzo Nobel or equivalent Paint of 80-120 micron thick. 7. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 8. Zinc primer paint is applied at all welding points prior to finishing. 9. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 10. Once the concrete is set, the equipment is fixed on to it. 11. High tensile steel with galvanized nut bolts are used for assembly. 12. Equipment made to GS Mark, EN16630, DIN 79000, ASTM F3101-15 & ISO 14001 International standard for outdoor fitness equipment. 13. Self-Explanatory stainless steel label fixed on equipment for ease of use

Providing and fixing of Air swing (double) with the following specifications 1. Dimensions (LxWxH): 1150 x 900 x 1250 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Leg Support frame of NB 50mm (G.I.) ‘C’ Class Pipe. 4. Handle support frame of NB 32mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimetres) 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Handle bars are provided with high end quality rubber grips. 9. Base plate cover made of virgin LLDPE plastic by rotational moulding with 4.00mm thickness, UV resistant and coloured. 10. Foothold made of MS Sheet Metal with rounded edges to prevent impact and injury. 11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 12. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 13. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 15. High tensile steel with galvanized nut bolts are used for assembly. 16. Equipment made to GS Mark, EN16630, DIN 79000, ASTM F3101-15 & ISO 14001 International standard for outdoor fitness equipment. 17. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Providing and fixing of Horse Rider Station with following specifications: 1. Dimensions (LxWxH): 1000 x 600 x 1100 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make 3. Main frame of NB 65mm (G.I.) ‘C’ Class Pipe. 4. Handle support frame of NB 50mm (G.I.) ‘C’ Class Pipe and other pipes of NB 32mm & NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimetres) 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Base plate cover made of virgin LLDPE plastic by rotational moulding with 4.00mm thickness, UV resistant and coloured. 9. Foothold made of NB 32mm (G.I.) ‘C’ Class Pipe. 10. Seat to be made up from virgin LLDPE manufactured by rotational moulding with 4.00 mm thickness, coloured, UV resistant and environmental friendly. 11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 12. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 13. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 15. High tensile steel with galvanized nut bolts are used for assembly. 16. Equipment made to GS Mark, EN16630, DIN 79000, ASTM F3101-15 & ISO 14001 International standard for outdoor fitness equipment. 17. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Providing and fixing of Leg Press - Double with the following specifications: 1. Dimensions (LxWxH): 2000 x 600 x 1800 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Seat Main frame of NB 50mm (G.I.) ‘C’ Class Pipe and Pipe connecting main post to seat main frame of NB 65mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimetres) 4. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 5. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 6. Zinc primer paint is applied at all the welding points prior to finishing. 7. Base plate cover made of virgin LLDPE plastic by rotational moulding with 4.00mm thickness, UV resistant and coloured. 8. Foothold made of NB 50mm (G.I.) ‘C’ Class Pipe. 9. Seats made up from virgin LLDPE manufactured by rotational moulding with 4.00 mm thickness, coloured, UV resistant and environmental friendly. 10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 11. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 12. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 13. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 14. High tensile steel with galvanized nut bolts are used for assembly. 15. Equipment made to GS Mark, EN16630, DIN 79000, ASTM F3101-15 & ISO 14001 International standard for outdoor fitness equipment. 16. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Providing and fixing of Pull Chair - Double with the following specifications:1. Dimensions (LxWxH): 2400 x 800 x 2000 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Seat main frame of NB 50mm (G.I.) ‘C’ Class Pipe, Pipe connecting main post with handle frame of NB 65mm (G.I.) ‘C’ Class Pipe. 4. Handle frame of NB 32mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimetres) 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Handle bars are provided with high end quality rubber grips. 9. Base plate cover made of virgin LLDPE plastic by rotational moulding with 4.00mm thickness, UV resistant and coloured. 10. Seat to be made up from virgin LLDPE manufactured by rotational moulding with 4.00 mm thickness, coloured, UV resistant and environmental friendly. 11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 12. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 13. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 15. High tensile steel with galvanized nut bolts are used for assembly. 16. Equipment made to GS Mark, EN16630, DIN 79000, ASTM F3101-15 & ISO 14001 International standard for outdoor fitness equipment. 17. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Providing and fixing of Seated Chest Press - Double with the following specifications: 1. Dimensions (LxWxH): 1800 x 700 x 2000 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Seat Main frame of NB 50mm (G.I.) ‘C’ Class Pipe. 4. Handle frame of NB 32mm and NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimetres). 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Handle bars are provided with high end quality rubber grips. 9. Base plate cover made of virgin LLDPE plastic by rotational moulding with 4.00mm thickness, UV resistant and coloured. 10. Seat to be made up from virgin LLDPE manufactured by rotational moulding with 4.00 mm thickness, coloured, UV resistant and environmental friendly. 11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 12. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 13. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 15. High tensile steel with galvanized nut bolts are used for assembly. 16. Equipment made to GS Mark, EN16630, DIN 79000, ASTM F3101-15 & ISO 14001 International standard for outdoor fitness equipment. 17. Self-Explanatory stainless steel label fixed on equipment for ease of use

Providing and fixing of Arm Wheel - Double with the following specifications :1. Dimensions (LxWxH): 850 x 800 x 1800 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Wheel frame of NB 32mm with connecting spokes of NB 25mm, Pipe connecting main pillar with wheel frame of NB 50mm. All pipes must be (G.I.) ‘C’ Class Pipes. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimetres). 4. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 5. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 6. Zinc primer paint is applied at all the welding points prior to finishing. 7. Base plate cover made of virgin LLDPE plastic by rotational moulding with 4.00mm thickness, UV resistant and coloured. 8. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 9. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 10. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 11. High tensile steel with galvanized nut bolts are used for assembly. 12. Equipment made to GS Mark, EN16630, DIN 79000, ASTM F3101-15 & ISO 14001 International standard for outdoor fitness equipment. 13. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Providing and fixing of Elliptical Exerciser with the following specifications: 1. Dimensions (LxWxH): 1200 x 550 x 1600 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Main frame of NB 80mm (G.I.) ‘C’ Class Pipe. 4. Handle frame of NB 32mm and NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimetres). 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Handle bars are provided with high end quality rubber grips. 9. Base plate cover made of virgin LLDPE plastic by rotational moulding with 4.00mm thickness, UV resistant and coloured. 10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 11. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 12. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 13. High tensile steel with galvanized nut bolts are used for assembly. 14 Equipment made to GS Mark, EN16630, DIN 79000, ASTM F3101-15 & ISO 14001 International standard for outdoor fitness equipment. 15. Self-Explanatory stainless steel label fixed on equipment for ease of use. 16. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury.

Providing and fixing of Double Cross Walker with the following specifications: 1. Dimensions (LxWxH): 1600 x 600 x 1600 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Handle main frame of NB 50mm and other connecting pipes of NB 32mm and NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimetres). 4. Foot support frame of 96 x 46 x 3mm MS rectangular pipe. 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Base plate cover made of virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness, UV resistant and coloured. 9. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury. 10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 11. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 12. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 13. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 14. High tensile steel with galvanized nut bolts are used for assembly. 15. Equipment made to GS Mark, EN16630, DIN 79000, ASTM F3101-15 & ISO 14001 International standard for outdoor fitness equipment. 16. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Providing and fixing of Tripe Twister (Standing Twister) with the following sepcifications: 1. Dimensions (LxWxH): 1300 x 1300 x 1650 mm. 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Handle Main frame of NB 32mm (G.I.) ‘C’ Class Pipe. 4. Handle frame spokes of NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimetres). 5. Foothold plate of made of MS Sheet Metal of 3mm thickness. 6. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 7. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 8. Zinc primer paint is applied at all the welding points prior to finishing. 9. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 10. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 11. Once the concrete is set, the equipment is fixed on to it. 12. High tensile steel with galvanized nut bolts are used for assembly. 13. Equipment made to GS Mark, EN16630, DIN 79000, ASTM F3101-15 & ISO 14001 International standard for outdoor fitness equipment. 14. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Providing and fixing of Rowing Machine with following specifications: 1. Dimensions (LxWxH): 1250 x 800 x 1150 mm. 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Main frame of NB 65mm (G.I.) ‘C’ Class Pipe. 4. Handle support frame of NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimetres). 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Base plate cover made of virgin LLDPE plastic by rotational moulding with 4.00mm thickness, UV resistant and coloured. 9. Foothold made of NB 50mm (G.I.) ‘C’ Class Pipe. 10. Seat to be made up from virgin LLDPE manufactured by rotational moulding with 4.00 mm thickness, coloured, UV resistant and environmental friendly. 11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 12. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 13. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 15. High tensile steel with galvanized nut bolts are used for assembly. 16. Equipment made to GS Mark, EN16630, DIN 79000, ASTM F3101-15 & ISO 14001 International standard for outdoor fitness equipment. 17. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Providing and fixing of Weight Assisted Shoulder Press with the following specifications: Weight Assisted Shoulder Press of minimum size 1350x1600x1150mm fabricated with main post of G.I. ‘C’ Class of NB 65 mm and other support and handle frames of NB 50 mm G.I. ‘C’ Class pipes only. Joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all welding points prior to finishing. Handle support frame made of GI 'C' Class Pipe of NB 25 mm. Handle bars shall be provided with high quality rubber grip. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. Machine to have weight plate adjustment arrangement made of 304 grade stainless steel and it must be designed to prevent theft of weight plates. Plates have to be fully locked in the machine but movable for the adjustment. Weight Change system should allow user to freely change resistance by changing individual weight plate of each arm. Weight on each arm should be adjustable between 0-15kgs. Seats to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of 4.00 mm, colourful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self-lubricated of SKF / equivalent make as approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps or sealed in for user safety. The equipment shall be fixed on ground with concrete of minimum strength M-25 and J shape welded bolt made of 18mm galvanized rod and covered with base plate cover after the installation complete. Equipment made to GS Mark, EN16630, DIN 79000, ASTM F3101-15 & ISO 14001 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label shall be fixed on equipment for ease of use.

Providing and fixing of Weight Assisted Chest Press with the following specifications: Weight Assisted Chest Press of minimum size 1100x1500x1300mm fabricated with main post of G.I. ‘C’ Class of NB 65 mm and other support and handle frames of NB 50 mm G.I. ‘C’ Class pipes only. Joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all welding points prior to finishing. Handle support frame made of GI 'C' Class Pipe of NB 25 mm. Handle bars shall be provided with high quality rubber grip. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. Machine to have weight plate adjustment arrangement made of 304 grade stainless steel and it must be designed to prevent theft of weight plates. Plates have to be fully locked in the machine but movable for the adjustment. Weight Change system should allow user to freely change resistance by changing individual weight plate of each arm. Weight on each arm should be adjustable between 0-15kgs. Seats to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of 4.00 mm, colourful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self-lubricated of SKF / equivalent make as approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps or sealed in for user safety. The equipment shall be fixed on ground with concrete of minimum strength M-25 and J shape welded bolt made of 18mm galvanized rod and covered with base plate cover after the installation complete. Equipment made to GS Mark, EN16630, DIN 79000, ASTM F3101-15 & ISO 14001 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label shall be fixed on equipment for ease of use.

Providing and fixing of Weight Assisted Lat Pull Down with the following specifications: Weight Assisted Lat Pull Down of minimum size 1200x1300x1650mm fabricated with main post of G.I. ‘C’ Class of NB 65 mm and other support and handle frames of NB 50 mm G.I. ‘C’ Class pipes only. Joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all welding points prior to finishing. Handle support frame made of GI 'C' Class Pipe of NB 25 mm. Handle bars shall be provided with high quality rubber grip. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. Machine to have weight plate adjustment arrangement made of 304 grade stainless steel and it must be designed to prevent theft of weight plates. Plates have to be fully locked in the machine but movable for the adjustment. Weight Change system should allow user to freely change resistance by changing individual weight plate of each arm. Weight on each arm should be adjustable between 0-15kgs. Seats to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of 4.00 mm, colourful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self-lubricated of SKF / equivalent make as approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps or sealed in for user safety. The equipment shall be fixed on ground with concrete of minimum strength M-25 and J shape welded bolt made of 18mm galvanized rod and covered with base plate cover after the installation complete. Equipment made to GS Mark, EN16630, DIN 79000, ASTM F3101-15 & ISO 14001 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label shall be fixed on equipment for ease of use.

Providing and fixing of Weight Assisted Rowing Machine with the following specifications: Weight Assisted Rowing Machine of minimum size 1500x1450x1650mm fabricated with main post of G.I. ‘C’ Class of NB 65 mm and other support and handle frames of NB 50 mm G.I. ‘C’ Class pipes only. Joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all welding points prior to finishing. Handle support frame made of GI 'C' Class Pipe of NB 25 mm. Handle bars shall be provided with high quality rubber grip. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. Machine to have weight plate adjustment arrangement made of 304 grade stainless steel and it must be designed to prevent theft of weight plates. Plates have to be fully locked in the machine but movable for the adjustment. Weight Change system should allow user to freely change resistance by changing individual weight plate of each arm. Weight on each arm should be adjustable between 0-15kgs. Chest support to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of 4.00 mm, colourful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self-lubricated of SKF / equivalent make as approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps or sealed in for user safety. The equipment shall be fixed on ground with concrete of minimum strength M-25 and J shape welded bolt made of 18mm galvanized rod and covered with base plate cover after the installation complete. Equipment made to GS Mark, EN16630, DIN 79000, ASTM F3101-15 & ISO 14001 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label shall be fixed on equipment for ease of use.

Carriage of cement and steel avg. lead of 10 km by MT

Carriage of sand and c. agg. avg. lead of 15 km by MT

Carriage of stone avg. lead of 4 km by MT

G. K. SPORTS