PROVN OF LADIES TOILET AT SHELTER NO 648 OFFRS MESS, PROVN OF INTERLOCKING TILING IN OFFICERS MESS NEAR PUF SH 1015 1017, PROVN OF RAIN SHED OVER EXISTING FOOTPATH AT PMS

Amount

Surface excavation n.exc.30 cm deep and averaging 15 cm deep and getting out in soft/loose soil including clearing away all grass vegetation, saplings, shrubs, brush wood, under growth, roots and trees n. exc. 30cm girth and removing rubbish upto a distance of 50 metre out of the periphery of the area complete all as specified and as directed.

Excavating in trenches , n.exc 1.5 m wide and n.exc 1.5 m depth for foundation etc or for shafts, wells, cesspits ,manhole pier hole, laying of cables, pipes etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in any kind of soil Note : Manual excavation to be done. During excavation if any damage occured to existing cable any type/ water pipe line, it will be contractor responsibilty to get it repair and make functional by providing jointing kit etc without any extra cost. Contractor has to repair it within 24 hrs so that essential service can not be effected due to such damage.If contractor fails to repair it within 24 hrs penalty @ Rs 500/- will be charged to contractor. In this GE decision will be final, conclusive and binding.

M & L for excavating over areas, n exc 1.5 m deep and getting out in soft/loose soil complete all as specified and as directed.

Excavating in post holes ( or similar holes) each n.exc 0.5 cum getting out , and removing surplus soil to a distance n.exc 50m and making good surface, in soft/loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, and well ramming in layer not exceeding 25 cm thick in soft/loose soil complete all as specified and directed.

Removing of excavated materials to a distance n. exc 50m and depositing where directed at a level n exc 1.5m above the starting point in soft/loose soil complete all as specified.

M&L Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

M&L for Hardcore using broken stone or boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface with interstices filled with stone dust complete all as specified.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L for 300 mm thick (compacted) in three layers of each 100mm thick in pavings, with mix of fly ash, clinker & stone dust in the proportion of 1:3:6 (ie 10% fly ash, 30% clinker and 60% stone dust ) laying in layers n. exc 10cm thick, watering, ramming and compacted with hand/power roller 8 to 12 tonn roller to required camber and gradient complete all as directed by Engineer-in-Charge.

M & L for PCC (1:4:8) Type D2 using 40 mm graded aggregates as in foundations ,fillings and mass concrete complete all as specified.

M & L for PCC type C2 1:3:6 using 40 mm graded aggregates as in foundations, fillings and mass concrete complete all as specified.

M&L for Reinforced cement concrete (Design Mix), M-25 grade concrete in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.

M&L for Reinforced cement concrete (Design Mix), M-25 grade concrete in Columns, pillars, piers, posts and struts complete all as specified and as directed..

M&L for Reinforced cement concrete (Design Mix), M-25 grade concrete in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.

M&L for reinforced cement concrete (Design Mix), M-25 grade concrete as in chajjas and similar work complete all as specified & directed by Engineer in Charge.

M&L for Reinfocement cement concrete (Design Mix), M-25 grade concrete in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

M&L type B-1 1:2:4 (20mm graded stone aggregate) providing RCC precast cement concrete as in cover slab for man hole and similar article with plain face set in cement mortar 1:6.

M&L for providing and laying at or near ground level factory made kerb stone of M- 25 grade cement concrete in position to the required line, level and curvature , jointed with cement mortar 1:3 , including making joints with or without grooves , including making drainage opening wherever required complete all as specified and as directed.

M&L for cast- in- situ cement concrete in Type C1 1:3:6 (20 mm graded aggregate) in lintels upto 1.5 m clear span, cills,steps and other similar bands, plinth courses,string courses and railings upto 60cm in height ,copings,apex stones,kerbs and the like including weathering ,slightly rounded or chamfered angles and throating as desired complete all as directed by the Engg-in-charge.

M&L Cement concrete 1:3:6 , Type C-1 (using 20 mm graded stone aggregate) in surface channels and drains and manholes complete etc.as specified & directed by Engr-in-Charge

M&L for cement concrete type B-1, 1:2:4 (using 20 mm graded stone aggregate) in surface channels and drains for benching complete all as specified and directed.

M&L for extra for forming fair finish drain channel upto 30 cm inner grith in cement concrete using extra cement complete all as specified and directed.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finihed surfaces.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams for rough finished surfaces etc.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished surfaces.

Form work to chajja and similar work including edges for rough finished surfaces complete all as specified and as directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping)

S&F Mild Steel TMT bars 10mm and over, cut to lenghth, bent to shape requird, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clip all as directed by Engineer in Charge.

All as per item No 29 here in before 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders

S & F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc using Fe 410 -W (Gde E- 250) quality A complete all as specified.

S & F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment using Fe 410 -W (Gde E- 250) quality A complete all as specified.

S&F mild steel screw bolts (machine made)with hexagonal or square heads at one end and screw other .and each screw end to be fixed with washers and nut exc 5 cm but n.exc 10 cm long complete all as specified and directed.

S&F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing conforming to Fe 290 Gde-E--165 complete all as specified and directed.

M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated of any profile steel sheet corresponding to IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified up to anyheight including all necessary scaffolding and safety measures complete all as specified and directed.

M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated plain steel sheet as per IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in ridge/ valley/ gutter fixed with self tapping screws as specified any height Mtr height including all necessary scaffolding and safety measures complete all as specified and directed.

M&L, Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete, all as specified and as directed.

M&L for brick work with flyash bricks straight or corve on plan to any radius in half bricks thick walls, built in cement mortar (1:4) complete all as specified and directed.

M&L for damp proof course 40mm thkM-20 (Nominal Mix) using 12.5mm graded stone aggregate with water proofing compound conforming to IS-2645 liquid grade as per manufacturer’s instructions with and including polythene film 200 micron over and including 85/25 grade Industrial bitumen (IS-702 : 1988) @ 1.5 kg/sqm blended with the dry sand @ 0.05 cubic meter/ sqm. complete all as specified and directed.

M&L for grading roof in cement mortar 1:3, 25mm thick in edge and 50mm thick in ridge including necessary curing complete all as specified in SSR Part I clause No 11.42.2

M & L for providing water proofing treatment with a layer of APP based polymeric membrane, 3 mm thick (minimum), weighing not less than 3.60 kg/Sqm reinforced with polymer non woven fabric (weighing not less than 160 gm/ Sqm) shall be applied over one coat of cold bituminious primer @ 0.40 ltr/ Sqm ( membrane shall be laid using butane torch and sealing all joints etc, complete all as specified and directed .( Note: The overlaps shall be of minimum 75 mm on longitudinal direction and 100 mm on transverse direction) complete all as specified and directed.

M&L for one coat of aluminium paint over APP membrane at roof surfaces complete all as specified and directed.

M&L for Rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces of wall finsihed fair and even

M&L for Rendering 15 mm thick cement plaster in CM 1:4 on fair faces of brick/concrete surfaces finished fair and even, using water proofing compound admixture (if directed) as per manufacturer's instruction, complete all as specified and directed. Note :- WPC will measuered and paid separatly under relevant item of schedule.

M&L for Rendering 10 mm thick cement plaster in CM 1:4 on fair faces of brick/concrete surfaces finished fair and even, using water proofing compound admixture (if directed) as per manufacturer's instruction, complete all as specified and directed. Note :- WPC will measuered and paid separatly under relevant item of schedule.

Supply only Liquid water proofing compound

S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complete

M & L for 4mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as spd and directed by Engr-In-Charge .

S&F factory made solid PVC door frame of size 50mmx47mm made out of 5 mm wood grain printed PVC shee twith mild steel square tube complete as per manufacturer specification & drawing complete all as specified and directed by Engr - in - Charge.

S&F factory made solid panel PVC door shutter 30 mm thick (stiles) consisting of frame made out of mild steel tubes for top & bottom rails. Mild steel frame shall be covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20 mm with stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side & as gap inserted for top rail and botttom rail, panelling of plain colour PVC sheet to be fitted in the mild steel frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement fixing in the frame at site as per specification ,drawing complete all as specified and directed by Engr - in - Charge.

Supply and fix butt hinges 100MM, medium weight, ss all as specified and directed complete all as specified and directed.

Supply and fix 150 mm long aluminium anodised barrel tower bolt of extruded section and fixed complete all as specified and directed.

Supply and fix 150 mm aluminium handle cast type, anodised, complete all as specified and directed.

S&F 300mm aluminium alloy, anodised, sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed.

M&L for 100mm thick Cement concrete type B- 2, 1:2:4 (using 400mm graded stone aggregate) as in floors finished even and fair complete all as specified.

M & L for PCC (1:4:8) 100 mm thick Type D2 using 40 mm graded aggregate used as in sub base floor/pavings and finishing complete all as specified and as directed.

M&L for 150mm thick PCC 1:1.5:3 nominal mix concrete with using 20mm graded stone aggregate as in path/hardstanding/paving etc with broom finished laid in alternate panel of size as directed by Engr-in Charge.

M & L 75 mm thick cement concrete type D-2, for PCC (1:4:8) using 40 mm graded aggregate as in sub base,etc complete all as specified and as directed.

M&L 25mm thick Cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) as in floor for levelling course complete all as specified and directed by Egineer-in-Charge.

M&L Non - skid Ceramic Coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry over screed bed or bedding layer of 15 mm thick with cement mortar 1:6 and pointed in white or coloured cement to match.

M&L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm thick set and jointed in neat cement slurry over back coat of layer of 10 mm thick with cement mortar 1:4 and pointed in white or colour cement to match the colour of tiles complete all as speciified and directed.

M&L for 75 mm thick cement concrete M10 (Nominal Mix) with 40mm graded crushed aggregate finished even and fair laid to a slope of 1 in 12, laid in alternate bays, each bay not exceeding 3 m length with joint filled with bituminous mastic filling comprising a mixture of 1 part of heated Industrial bitumen 85/25 grade and two parts of heated sand as in plinth protection complete all as specified.

M&L for machine pressed precast concrete interlocking paver block pre-polished any shape and size with grey cement and pigment confirming to IS 15658-2006 of 60 mm thickness M-35 Grade complete all as specified and directed.

Material and labour for 25 mm thick chequered cement concrete tiles of size 30x30x25 mm mm,set ,jointed and pointed using with grey cement and pigment in floors, pavings etc including the setting and jointing in neat cement plaster or slurry 0.3 kg/sqm over 20mm thick screed bed or bedding layer in cement mortar 1:6 complete all as per specification.

Preparing new surfaces of walls plastered and applying with 03 coats of white wash on walls complete all as specified.

M&L for preparation of new surfaces of ceiling and applying three coats of white wash complete all as specified and as directed..

Material & Labour for preparation of new surfaces of plastered walls and applying Two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. over and including a coat of primer and 1.0 mm thick white wall care putty (premium quality) over plastered surfaces of walls to prepare the surface even and smooth complete all as specified.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over preparation of new surfaces complete all as specified.

M&L for preparation of new plastered surface of wall applying of two coats of cement base paint over a coat of primer complete all as specified and directed.

M&L for preparing of new steel & iron surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enameled paint over a coat of Red oxide zinc chrome primer zinc chrome complete all as specified and as directed.

S&F Vitreous china wash down water closet pan, Pedestal pan and trap(excluding flushing cistern and flush pipe),connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc and including plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel CP or aluminised hinging device all as specified and directed.

S&F closet Vitreous china squatting pan Orissa pattern of size 580x440mm white with integral foot rests (excluding flusing cistern and flush pipe) including connection to trap and to flushing pipe, antisyphonage connection pipe etc complete making good disturbed surface with existing finish of floor all as specified & directed by Engineer-in-Charge.

S&F in repairs PVC low level flushing cistern, 10 litres capacity, syphonic action type white body with inlet ball valve, float , handle, bracket, flush pipe etc complete & connecting to WC complete.

Supply only Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern etc complete all as specified and directed.

Supply & fix vitreous china wash basin, white, flat back, size, 550X400mm including bracket for fixing 32 mm waste coupling, waste pipe etc complete all as specifid and direted.

Supply and fix Pillar taps, 15mm bore, fancy type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with long scrwed shanks and fly-nuts, screwed for iron pipe or for connection pipe complete complete all as specified and directed.

S&F CP health faucet with 1.50mtr long tube & hook with necessary all fixig arreangements to fix GI water pipe connections complete all as specified and directed by Engr-in-charge

S&F PVC flexible urinal waste pipe 1/2 inch dia fixed to urinal stall waste coupling complete all as specified and directed.

S&F Bib taps of 15mm bore fancy type, chromium plated cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for brass ferrule complete all as specified and directed.

S&F stop valve of 15mm bore, chromium plated with long shank and cup concealed type cast copper alloy, screwed down, high pressure, with crutch handle, screwed both ends for brass ferrule complete all as specified and directed.

S&F CP tubular towel rail 20mm dia D type 60cm between two flange including bracket complete all as specified and directed by Engr -in-Charge.

S&F PVC connection 15 mm size PTMT nuts of length ength 600 mm complete all as specified and directed

S&F soap dish vitreous china white size 160x160x90mm approx all as directed by Engineer -in-Charge

S&F 15 mm dia bore steel tubing medium grade galvanised with all fittings and connection complete all as specified and directed.

S&F 20 mm dia bore steel tubing medium grade galvanised with all fittings and connection complete all as specified and directed.

M & L for fixing PVC (SWR) pipes of 100 mm bore diameter single socketed, in any length with rubber ring joints, laid in trenches or in floors.

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall,laid in trenches or in floors.

S&F 110mm bore PVC (SWR) bends any radius complete all as specified and as directed by EIC.

S&F 75mm bore PVC (SWR) bends any radius complete all as specified and as directed by EIC.

S&F 110 mm bore PVC (SWR), junction single, (single T), equal or unequal with access door complete all as specified and directed.

S&F 75 mm bore PVC (SWR), junction single, (single T), equal or unequal with access door complete all as specified and directed.

Material and labour for cement concrete bed to drain pipe for 150mm bore of pipe including forming cradles in Cement concrete 1:3:6 Type C2 complete all as specifiedand and as directed.

Material and labour for cement concrete bed to drain pipe for 200mm bore of pipe including forming cradles in Cement concrete 1:3:6 Type C2 complete all as specifiedand and as directed.

Supplying and laying of PVC underground drainage sewer system pipe bearing 160 mm dia SN 4 including jointing with couplar, bend tee as per site requirement complete laid in trenches or floors complete all as specified and directed.

S&F Reinforced concrete pipes ,class NP2, 200 mm bore laid and jointed in trnches or in floors complete with collar all as specified and as directed.

M&L for Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound Grade 'B' all as specified and directed.

M&L for Forming Construction joint 150mm deep x 10mm wide (Grade B) filled with sealing compound Group 'B' complete all as specified and directed.

M & L for concealed point wiring for fan/light point controlled by one one way switch complete with 1.5 sq mm FRLSH,PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red/yellow/blue wires for phases and black wire for neutral),drawn into and including non metalic PVC rigid conduit medium grade of suitable size and conduit accessories fixed on wall, floor, roof etc. and including PVC FRLSH insulated 1.5 sq mm copper conductor for earth continuity (Green Colour) and connected to common earth dolly including sunken in GI terminal box 2.8 mm thick bakelite hylam sheet cover, ISI marked with CM/L no. for mounting switch & sockets ect. Note : a) Note :- Cost of PVC conduit, cutting chases of wal/ceilingl, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate.

All as per item No.99.00 here-in-before but 5 Amp socket on same board with other switches.

All as per item No 99.00 here-in-before but using 2.5 sqmm FRLSH PVC insulated unsheathed multi strand copper cable (1100 V) for line conductor and 2.5 Sqmm FRLSH PVC insulated unsheathed solid copper cable (1100 Volts) for earth continuty wire for one 15/16 amp multi socket out let on independent board.

Supply and fix switch piano flush type, single pole , 5/6 Amps, one way complete all as specified.

S&F socket outlets 2 in 1, 5 pin, 5/6 Amps flush type 230/240 V complete all as specified and as directed .( For Same Board only)

S&F Switch socket combination 2 in 1, 5 A flush type 230/240 V complete all as specified and as directed .

Supply & fix ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps complete all as specified.

Supply and fixing lamp holder, PVC/polycarbomate type with back plate straoght of angle suitable for LED lamp complete all as specified and directed

Supply and fixing for concealed type sub main wiring with two run of 6.00 Sqmm single core PVC FRLSH PVC insulated unsheathed stranded copper conductor (Red/yellow/blue wires for phases and black wire for neutral) drawn in and including through Rigid non-metallic PVC conduit(medium) ISI marked of size 25mm bore with all fittings like tee/Bend/Elbow/Reducer/Bell mouth/Junction / Terminal Boxes etc. and fixing accessories such as coupler, lock nuts, saddles, pipe hook etc. including one run of 6.00 Sqmm single core PVC FRLSH PVC insulated unsheathed stranded copper conductor as earth wire (green in colour) complete all as specified. Note : (i) Note : 2 runs of line conductor, one run of earth continuity conductor, one run of PVC conduit shall be measured as unit length. (ii) Cost of PVC conduit, conductors, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate.

Supply & fixing LED security light 35/36 watt (Min) 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with BIS approved driver and lamp, Aluminum die cast housing High efficiency long life LED package in integral module with lumen efficacy of 115 lm/W (Min) and viewing angle of 45 degree to ensure better uniformity, electronic LED driver (SMPS based constant current supply) with Output Short-circuit protection, Surge protection & other reliability test as per latest IS. operational voltage of 170 volts to 270 volts, frequency of 50 Hz, protection grade IP 66, IK-08 CRI greater than or equal to 70% , CW available CCT of 5700K/6500K, power factor of minimum 0.95 , life span of minimum 50000 working hours cincluding necessary electrical connections by PVC sheathed copper conductor wire of 3 core x 1.5 Sqmm and necessary fixing arrangement all as specified. Note : (i) The minimum requirement of lumen efficiency, lumen output and power consumption has been specified. However, as per availability, the bidders may opted higher specification with out any extra cost. The quoted rate is deem to be included for that and no extra payment will be made on this account. (ii) The fittings should be marked 'Date of installation" and "Date of Procurement" with marker pen

S&F in repairs LED 20 Watt tube light fitting intregated type, including LED retrofit tube lamp 20 W , LED tube light nominal power 20 Watt, LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, , lumen efficacy of minimum 110 lumens per watt, , integrated electronic driver (SMP based constant current supply) with output short circuit protection and surge protection upto 2.5 KV, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, THD below or less than 20%, CW available CCT of 6500K, power factor of minimum 0.95 life span of minimum 50000 working hours and LED batten with aluminium housing and polycarbonate diffuser complete fitting including connecting with PVC insulated multistranded copper flexible cable 1.0 sqmm three core, and PVC round/ square box white colour x 2 Nos for mounting of fitting complete all as specified & directed. . Note (i) Make of batten and LED tube lamp should be of same make.

S&F in repairs LED 9/10 Watt tube light fitting mirror intregated type, including LED retrofit tube lamp 9/10 W , LED tube light nominal power 9/10 Watt, L LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, , lumen efficacy of minimum 115 lumens per watt, , integrated electronic driver (SMP based constant current supply) with output short circuit protection and surge protection upto 2.5 KV, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, THD below or less than 20%, CW available CCT of 6500K, power factor of minimum 0.95 extruded aluminium LED battens life span of minimum 50000 working hours complete fitting including connecting with PVC insulated multistranded copper flexible cable 1.0 sqmm three core, and PVC round/ square box white colour x 2 Nos for mounting of fitting including taking down old unserviceable complete all as specified & directed. Note : Make of batten and LED tube lamp should be of same make.

Supply install & testing exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230v, 50Hz, Single phase, 1200 RPM, copper winding of sweep 250mm complete fixed/grouted to wall with suitable bolts, nuts etc, and connecting up with & including 3 core flexible copper conductor cable (1.0mm2 size/core) from ceiling rose to exhaust fan including cutting hole suitable for fixing exhaust fan complete all as specified and directed. Make Havells or equivalent in Bajaj/Crompton/orient.

S & F sheet metal enclosure for MCB, DB, SPN, 240 Volts, 100 Amps rated busbar, Confirming to IS as per IEC 61439-3, 4 way Double door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43, Ik09 including fixing the DB box flush in wall of any type and making good the distrubed surface to match as the existing with all as specified and directed .

Supply and fixed MCB SPN 32 Amps, 'C' curve 10kA, 240 Volts and to be housed in DBs complete including necessry connection all as specified and directed.

Supply and fixed MCB SPN 40 to 63 Amps, 'C' curve 10kA, 240 Volts and to be housed in DBs complete including necessry connection all as specified and directed.

Supply and fixed MCB SP 6-32 Amps, 'C' curve 10kA, 240 Volts and to be housed in DBs complete including necessry connection all as specified and directed.

Material and labour for earthing complete with Galvanised steel earth plate electrode 600x600x6 mm mm buried directly in ground (Earth pit not less than 2.25m below ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to GI wire 4 mm as earth lead by means of bolt, nuts, check nuts and washers of galvanised iron or steel, upto 7.5m length, earth strip protected by and including 15 mm dia GI pipe (light grade) and connected to main test point or body of pole/pannel or lightening arrester of main controlling switch as directed including concrete pit in PCC (1:3:6) type C1 , Precast RCC (1:2:4) Type B1 cover slab of size 54x54x5 cm reinforced with 8 mm dia TMT bars @ 100 mm C/C both ways with one handle for lifting made out of 10 mm dia TMT bar embedded in precast cover slab, funnel, wire mesh, 20 mm bore GI Pipe (Medium Grade) for watering, Charcoal and salt in alternate layers of 15 cm (Compacted Thickness) around the earth electrode including necessary excavation, earth work in any type of soil and disposal of spoil to a distance n.exc 50 m and necessary testing complete all as shown in Electrical Plate No 3 of SSR Part-I. NOTE : 1. The unit rare includes for protectionh GI pipe of 15mm and watering pipe of 20mm bore including excavation for earth pit in any type of soil/disintegrate rock. 2. Contractor has to bring agriculture soil from outside of defence land and fill in earth pit to acheive desired result as the soil resisitivity is very high. 3. The cost of GI wire including protection pipe, from top of earth plate upto 7.5 meter above/below ground level is deemed to be included in the unit rate. 4. All the joints in GI wire and connectgion with earth plate to be welded through brazing and in addition by providing double brass nut bolt and washer. 5.Costing of welding and nut bolts are deemed to be included in the unit rate

Supply, Laying and testing cable LT XLPE sheathed,PVC insulated screened PVC bedded,galvanised steel strip of wire armoured electric power cable heavy duty with solid aluminium conductor 1100 volt grade, laid in trenches/surface of wall/in GI pipe along with pole for connection to OH lines,including brass cable glands,clamps,etc of 2 core 10 sqmm.

M&L Sand Cushioning (dry) in trenches for protection of UG Cables (below, above and around the UG Cable laid in Trenches) of 230mm Spread thickness and consolidated (punned) upto 180mm thickness, complete all as specified and as directed. (NOTE : For the purpose of Payment, Punned thick-ness of Sand Cushioning only shall be Measured and Paid )

Supply and laying well burnt Bricks , locally available best quality (sub class "B" bricks) laid in trenches perpandicular to U/G cable for cable protection complete all as specified.

S&F Pipes galvanized, 50 mm bore “light grade”, supplied and laid complete including necessary fittings such as tees, bends, elbows, sockets, reducers etc as per site requirement or specified.

S&F Pipes galvanized, 25 mm bore “Medium grade”, supplied and laid complete including necessary fittings such as tees, bends, elbows, sockets, reducers etc as per site requirement or specified.

Supply& fixed gun metal, gate valve, 25 mm dia with iron wheel head, screwed both ends for iron pipe and fix complete all as specified and directed.

S & F rotational moulded polyethylene ISI marked (vertical cylindrical with close top) as per IS 12701: 1996 of 500 litres capacity hoisted and fixed in position with and including Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for 25mm bore dia iron pipe, provision of 25 mm dia medium grade GI pipe for connecting inlet, outlet, over flow and washout pipes including dismantling the existing one and removing to store complete all as specified and as directed.

Intime Commotrade Pvt Ltd (BID ID -3426286)

SPS TRADING (BID ID -3426351)