REPAIR MAINTENANCE OF EM INSTALLATION, MACHINE BASE STRUCTURES AND CIVIL WORKS AT MES INSTALLATIONS OF BELGAUM MILITARY STATION UNDER GE BELGAUM

Amount

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion in cement concrete / brick work etc., and making good disturbed ground, complete all as specified and as directed.

M&L PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete, complete all as specified and as directed.

M&L for Pre-cast cement concrete solid block masonry type C1, 1:3:6 (using 20 mm graded stone aggregate) exc 10 cm width and setting in CM 1:6, with and including demolition of existing brick work of any description, complete all as specified and as directed.

S&F IN REPAIR chain link fencing of mesh size 50mmx50mm, with 4mm dia hot dip GI wire as per IS 2721:2003, including line wires any type of standards, rails, straining bolts, etc. including provision of binding wire, with and including dismantling existing u/s fencing wire mesh of any size & type, complete all as specified and as directed.

S&F Mild steel work such Flat iron, angle etc., for securing wire mesh with and including drilling holes etc., cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) and similar work conforming to Fe-290 Gde E-165, complete all as specified and as directed.

M&L for Mild Steel Round bars 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips or welded, confirming to Gde Fe-290 Gde-165, with and including dismantling wrought iron or mild steel work of any description, complete all as specified and as directed.

M&L for Preparation of new or previously untreated surfaces of steel or steel based surfaces of any description, not otherwise described, over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing, confirming to Fe410-W (Gde Fe-250 Quality 'A'), with and including dismantling existing steel work of any description, complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.45mm thick (TFT) of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws, with and including taking down existing u/s plain / CGI sheet roof of any description, complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.45mm thick (TFT) of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, with and including taking down existing u/s steel sheet roof of any description, complete all as specified and as directed.

M&L for PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in roof padding concrete mixed with polyester fibres as secondary reinforcement @ 0.25% of weight of cement, provided to achieve desired slope and finishing the surface even and smooth without using extra cement, with and including demolition of cement concrete of any description and in any position, complete all as specified and as directed by Engineer-in-Charge. Note: Supply only Polyester fibres shall be measured and paid separately.

Supply only polyester triangular fibres of 6/12mm long with circum circle diameter of 30-35 microns, designed for melting point of 240-260 degree Celsius & having specific gravity 1.34 -1.40 as secondary reinforcement in all types of concrete, complete all as specified.

M&L for 10mm thick Rendering on fair faces of concrete roof surfaces in cement mortar 1:3 mixed with water proofing compound as per manufacturer's instructions, complete all as specified and as directed. Note: Supply of WPC will be measured and paid separately.

Supply only Integral Water Proofing Compound. Make: Pidilite Industries Ltd Taloja / FOSROC / Dr Fixit / Asian paints

M&L for water proofing treatment including complete removal of old roof treatment, removal of debris out side MD land and applying new roof treatment consisting of following:- (a) Removing existing roof treatment with cement screed, preparation of roof surface by brushing with a neat cement slurry @ 3Kg/SqM . (b) Preparation of roof surface thoroughly cleaning by using wire brush [Mechanical / hand brush] to make it free from any loose particle, dirt / dust, etc. and applying one coat of cold applied bituminous primer @ 0.20 Lit per sq.m. (c) Providing Atactic polypropylene polymeric modified prefabricated water proofing membrane five layered reinforced with non woven polyester matt of minimum 3mm thick weight not less than 3 Kg/Sqm shall be laid using butane torch application over entire roof surface with over laps of 100mm in both the directions. (d) Ponding complete all as specified and as directed by Engineer-In -Charge. (e) Finally roof shall be finished with two coats of bituminous aluminium paint @ 0.10 Kg/Sqm for each coat.

M&L for 100mm thick plain cement concrete 1:4:8 type D2 (using 40mm graded stone aggregate) as in floors/paving's, with and including demolition of cement concrete (un-reinforced) as in ground floor, complete all as specified and as directed.

M&L for 50mm thick plain cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in flooring / paving's, with and including demolition of cement concrete (un-reinforced) as in ground floor, complete all as specified and as directed.

M&L for 75mm thick plain cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) as in plinth protection, finished even and fair without using extra cement including making construction joints in 3 metres interval and joint filled with sealing compound, with and including demolition of cement concrete (un-reinforced) as in ground floor, complete all as specified and as directed.

M&L for Premium quality, joint free ceramic glazed coloured wall tiles of 7 to 8mm thick (square / rectangular) area of each tile not exc 0.18Sqm, on vertical surfaces such as dado and the like, set and jointed in neat cement slurry and pointed in coloured cement to match, laid over & including 10mm thick rendering in CM 1:3 and including taking down existing dado/skirting with backing mortar, complete all as specified.

M&L for Premium quality, joint free coloured Non skid ceramic tiles 7mm to 8mm thick (square/rectangular) area of each tile exc. 0.06 Sq.m. but n. exc. 0.11Sq.m, as in floors etc., laid over and including 15mm thick screed bed or bedding layer in CM (1:4), set and jointed in neat cement slurry and pointed in coloured cement to match, with and including dismantling existing floor tiles of any type with bedding mortar, complete all as specified and directed.

S&F Machine cut Kota stone slab 20-25mm thick, as in flooring, laid over and including 20mm thick screed bed or bedding layer in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab, rubbing and polishing, with and including demolition of existing stone slab or tiles floor, complete all as specified and as directed.

S&F Machine cut Kota stone slab 20-25mm thick, as in skirting, dado, steps, cooking platform and the like, laid over and including 10mm thick backing coat in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab, rubbing and polishing, with and including demolition of existing floor, complete all as specified and as directed.

M&L for rubber coated chequered cement concrete coloured tiles 23-25mm thick, of approved shape and size, as in floor / path, set, jointed and pointed in neat cement slurry with grey cement and pigment, glossy finish on top, laid over and including 15mm thick screed bed in CM 1:4, including demolition of old floor of any thickness, complete all as specified.

M&L for Factory made Machine pressed pre-cast cement concrete interlocking paver block of any shape and size with glossy finish on top, confirming to IS 15658-2006 of 60mm thick, M-35 grade with grey cement and pigment, with and laid over and including 50mm thick sand cushion (crushed stone sand / M sand) under interlocking paver block including watering and consolidation, with and including dismantling existing stone sett paving of any thickness, removing rubbish off the premises, complete all as specified and as directed.

M&L for Rendering 5mm thick in CM 1:3 as in ceiling surfaces, finished even and smooth without using extra cement, with and including taking down existing cement plaster of any description, complete all as specified and as directed.

M&L for Rendering 10mm thick on fair faces of brick work or concrete surfaces of walls in CM 1:6 finished even and fair without using extra cement, with and including taking down existing cement plaster of any description, complete all as specified and as directed.

M&L for 15mm thick Rendering on fair faces of brick work or concrete surfaces in two layers as 10mm thick in cement mortar 1:6 followed by 5mm thick in cement mortar 1:4 mixed with water proofing compound as per manufacturer's instructions and finish the surface even and smooth without using extra cement, with and including taking down existing cement plaster of any description, complete all as specified and as directed. Note: Supply of WPC will be measured and paid separately.

M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of alkali resistant primer and 1mm thick wall case putty, complete all as specified and as directed.

M&L for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm with and including complete removal of existing treatment on wall with wire brush, scrapping down smoke soot ,mould, moss and efflorescent salts, trading oil and greasy spots, filling holes & cracks with cement base putty and including preparation of old decorated surfaces of wall, complete all as specified and as directed.

M&L for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm with and including complete removal of existing treatment on walls / beams/coloumns of OVER HEAD TANK with wire brush, scrapping down smoke soot ,mould, moss and efflorescent salts, trading oil and greasy spots, filling holes & cracks with cement base putty and including preparation of old decorated surfaces, complete all as specified and as directed. Note: Quoted Rate shall be inclusive of providing necessary scaffolding and other arrangements as required for painting of OHT surfaces height upto 35m.

M&L for applying two coats of Oil Bound Distemper over a coat of primer and a layer of 3mm thick wall care putty on walls with and including complete removal of existing treatment on wall with wire brush, scrapping down smoke soot ,mould, moss and efflorescent salts, trading oil and greasy spots, filling holes & cracks with cement base putty and including preparation of old decorated surfaces of wall, complete all as specified and as directed.

M&L for preparation of new wall surfaces and applying three coats of white wash, complete all as specified and as directed.

M&L for preparation of new ceiling surfaces and applying three coats of white wash, complete all as specified and as directed.

M&L for applying three coats of white wash on walls with and including complete removal of existing treatment on wall with wire brush, scrapping down smoke soot, mould, moss and efflorescent salts, trading oil and greasy spots, filling holes & cracks with cement base putty and including preparation of old decorated surfaces of wall, complete all as specified and as directed., complete all as specified and as directed.

M&L for applying three coats of white wash on ceiling with and including complete removal of existing treatment on ceiling with wire brush, scrapping down smoke soot ,mould, moss and efflorescent salts, trading oil and greasy spots, filling holes & cracks with cement base putty and including preparation of old decorated surfaces of wall, complete all as specified and as directed., complete all as specified and as directed.

M&L for applying two coat of cement based paint (white or tinted) with and including preparation of new decorated surfaces of wall of any description, complete all as specified and as directed.

M&L for applying one coat of cement based paint (white or tinted) with and including preparation of old decorated surfaces of wall of any description, complete all as specified and as directed.

M&L for Preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed.

M&L for Preparing old wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed.

M&L for applying two coat of synthetic enamel paint with and including preparation of old painted steel and steel based surface of any description but not exceeding 10cm width or girth, complete all as specified and as directed.

M&L for applying one coat of synthetic enamel paint with and including preparation of old painted steel and steel based surface of any description but not exceeding 10cm width or girth, complete all as specified and as directed.

Taking down chowkhat or frames with shutters (without taking off shutter from the frame) of area exc 1.5sqm but n. exc. 4.0 sqm each, complete all as specified and as directed.

Taking down shutters of any description of area exc 1sqm but not exc 2sqm each, complete all as specified and as directed.

M&L for 4mm thick sheet glass ordinary quality and glazing with oil putty/ wooden beads in square exc 0.5 Sqm in each pane, with and including hacking out old glass panes any thickness & size from wooden frames or brick /concrete surfaces, glazed with oil putty or fixed with wooden beads, complete all as specified and as directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm fixed with tinned tack or stainless wire staples, complete all as specified and as directed.

S&F IN REPAIR Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm fixed with tinned tack or stainless wire staples, complete all as specified and as directed.

M&L for Second class hard wood plain solid straight chowkhat and frames, wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints, complete all as specified and as directed.

S&F 35mm thick factory made 2nd class hard wood plain, framed, panelled shutters (two panels) with lock rail and panel of 12mm veneered particle board with commercial veneering on both faces, size of rail and style as per IS - 1003 (Part I), kiln seasoned and chemically pressure treated, complete all as specified and as directed.

M&L for Steel windows with side hung shutters, including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, complete all as specified and as directed.

M&L for solid PVC Door Frame of Size 50mm x 47mm out of 5mm prelaminated PVC sheet on both sides reinforced with M.S Square tube, supplying and fixing in opening as per specification and drawing, complete all as specified and as directed.

M&L for Factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tube of top and bottom rails, MS frame shall be covered with heat moulded prelaminated PVC "C" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelaminated PVC sheet for top rail ,lock rail and bottom rail on either side and as gap insert for top and bottom rail. Panelling of prelaminated PVC sheet to be fitted in MS frame welded /sealed to the stiles and rails with suitable PVC sheet bedding and jointed together with solvent cement as per specification and drawings, complete all as specified and as directed.

S&F MS butt hinges, cold rolled, medium weight 100mm size, ISI marked, complete all as specified and as directed.

S&F MS butt hinges, cold rolled, medium weight 75mm size, ISI marked, complete all as specified and as directed.

S&F 150mm long Extruded aluminium alloy 'D' type handles, fabricated type, anodised complete all as specified and as directed.

S&F 100mm long Extruded aluminium alloy 'D' type handles, fabricated type, anodised complete all as specified and as directed.

S&F Aluminium anodised barrel tower bolt of extruded section of size 150mm long complete, complete all as specified and as directed.

S&F Aluminium anodised sliding door bolt 300mm long with hasp & staple (Bolt type) and fixing clips of sheet cast or extruded section of cast aluminium alloy complete all as specified and all as directed.

S&F IN REPAIR Aluminium anodised sliding door bolt 300mm long with hasp & staple (Bolt type) and fixing clips of sheet cast or extruded section of cast aluminium alloy complete all as specified and all as directed.

S&F Aluminium powder coated frame for doors, partitions, windows and ventilators with one or more rebates of extruded built up standard tubular and other section of approved make, according to IS 1868 (Thickness of powder coating not less than 50 micron) fixed with rawl plugs, screws or fixing with clamps or with expansion hold fasteners including necessary filling up of gaps of junctions at top, bottom and sides with aluminium sections should be smooth, rust free, straight mitred and jointed mechanically wherever required including cleat angle, aluminium anodised screws etc. complete all as specified and as directed.

S&F IN REPAIR Bib tap, chromium plated, quarter turn, fancy type, cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule of 15mm bore dia of pipe, complete all as specified and as directed.

S&F IN REPAIR Stop Valve, chromium plated, fancy type, cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule of 15mm bore dia of pipe, complete all as specified and as directed.

S&F IN REPAIR 15mm bore chromium plated pillar taps, fancy type, cast copper alloy with capstan heads, screwed down high pressure with or without lettered Hot or cold with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed.

S&F IN REPAIR PVC connections 15 mm size with PTMT nuts 450mm long, completeall as specified and as directed.

S&F PVC (SWR) Floor / Nahani trap with grating of 75mm dia outlet, setting and jointing with solvent, complete all as specified and as directed.

S&F IN REPAIR PVC grating doom 150mm dia with / with waste hole, fixed with white cement, complete all as specified and as directed.

S&F IN REPAIR Vitreous china Wash down water closet pan EWC (Pedestal pattern), white with 'P'or 'S' trap étc, (excluding flushing cistern and flush pipe) including plastic water closet seat cover closed pattern with flat bottom cover, mild steel chromium plated or aluminised hinging device, fixing bolts, etc, complete all as specified and as directed.

S&F in repair Vitreous china squatting pan, Orissa pattern size 580 x 440 mm white with integral foot rest including 'P' or 'S' trap etc., with and including cement concrete bedding, complete all as specified and as directed.

S&F IN REPAIR PVC trap S/P/Q of size 125/100mm, completeall as specified and as directed.

S&F IN REPAIR PVC valveless, syphonic action type low level flushing cistern, 10 ltrs capacity, white with inlet ball valve, float and handle soft touch type including brackets, PVC flush pipe, fixed with CP brass screws, complete all as specified and as directed.

S&F IN REPAIR Vitreous china wash basin, white, flat back of size 550x400mm, including CI brackets, with PVC waste pipe and waste fittings and cutting for and pinning in ends of brackets or erecting stands etc., complete all as specified and as directed.

M&L for Greasing & easing of Mild Steel rolling shutters of area exc 10SqM but not exc 20SqM each, for full movement and for easy operation of shutters, complete all as specified and as directed.

M&L for Greasing & easing of Mild Steel rolling shutters of area not exc 10SqM each, for full movement and for easy operation of shutters, complete all as specified and as directed.

S&F Steel rolling shutters, gear operated type with ball bearing with bevel gear box and crank handle, as specified including top cover, anchoring rod, hasp and staple, 1.25 mm laths, guide channels and one shop coat of primer, including erected in position, complete all as specified and as directed.

S&F IN REPAIR Factory Made hood covers of mild steel sheet of 1mm thick, hexagonal, square or circular shape, fixed to existing angle iron stiffners at bottom edge and to bracket plate with and including applying one shop coat of red oxide primer, complete all as specified and as directed.

M&L Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and as directed.

S&F Rolled mild steel roof trusses (framed) trussed purlins, rafters, struts (beam, tee, angle channel or flat sections including distance pieces, cleats etc. conforming to grade Fe 410-W Gde E - 250 quality 'A', complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for of any description, complete all as specified.

PRATIBHA ASSOCIATES (BID ID -3313482)

M/S MAHADEV M PATIL (BID ID -3312111)

M/S VISHWAROOP ELECTRONICS AND ELECTRICALS (BID ID -3310534)

Sadhana Constructions & suppliers (BID ID -3316140)

SHREESAMARTH CONSTRUCTION (BID ID -3312329)

DHAIRYASIL RAMAKANT DESAI (BID ID -3316438)

M/s B C CHOUGULE (BID ID -3315380)

M/s.GOODWILL ELECTRICALS (BID ID -3315656)

ASHOK M RAJGOLKAR (BID ID -3320122)