REPAIRS/ REPLACEMENT OF JOINERY, TILING, PLUMBING, FALSE CEILING, FENCING AND OTHER MISC B/R WORKS AT HEMA LINE, THIMMAYA LINE, MES COLONY AND OFFRS MD ACCN UNDER GE (MCTE) MHOW

Amount

Item No. 1 Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets, complete all as specified and directed.

Item No. 2 S&F false ceiling using 595mm x 595mm x 6mm thick, E-board designer ceiling boards with and including S&F of snap grid of hot dip galvanised steel sections as specified (supra fine 15mm edge grid exposed tee hanging suspension system wih clamps & hangers etc.), with and including all necessary fittings & accessories, complete all as specified and directed. (Make : DUNE-Microlook of 'Armstrong' or equivalent products of Nittobo/ Everest)

Item No. 3 Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings, complete all as specified and directed.

Item No. 4 S&F, Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet, 0.50mm thick, of any colour (as approved by the Engr-in-Charge), having tensile strength of 550 MPa, as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Item No. 5 S&F, Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws, complete all as specified & directed.

Item No. 6 Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed.

Item No. 7 S&F, steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes confrming to IS 1161-1979 grade St-240 ,complete all as specified and directed.

Item No. 8 M&L for preparation of new steel surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamelled paint over a coat of red oxide primer, complete all as specified and directed.

Item No. 9 Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground, complete all as specified & directed.

Item No. 10 Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc., including provision of binding wire, complete all as specified & directed.

Item No. 11 Supply only galvanized iron chain link fencing approved size, complete all as specified and directed.

Item No. 12 Excavation in hard/ dense soil as in post holes each n.exc 0.50cum, getting out, returning, filling, in and ramming earth or broken rubble mixed with earth around, in layers n.exc. 25cm, watering and removing surplus soil, complete all as specified & directed.

Item No. 13 M&L for PCC 1:2:4 type B-2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete, filling in column footing etc, complete all as specified & directed.

Item No. 14 S&F mild steel angle iron posts and struts in fencing post and iron flats for securing chain link fencing including all necessary drilling bolting etc. and similar work, complete all as specified & directed.

Item No. 15 S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5 cm long and dia of shank 5 to 10mm, complete all as specified & directed.

Item No. 16 M&L for mild steel round bars 10mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips, complete all as specified and directed.

Item No. 17 S&F mild steel framed work such as framed and hung as gates ornamental and intricate design, including pintle hinges, stops,hand-made sliding bolts, etc grills, gratings etc with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framed work and similar works conforming to Fe-290 Gd E-165, complete all as specified and directed.

Item No. 18 Taking down cement or cement lime plaster of any description including racking out joints, hacking for keys, scrubbing down with water etc, complete all as specified and directed.

Item No. 19 M&L for Rendering 15mm thick on fair faces of concrete/ brick interior surfaces in cement mortar 1:6 as per manufacturer's instruction, finished fair and even without using extra cement, complete all as specified & directed.

Item No. 20 M&L for Rendering 15mm thick on fair faces of brick work or concrete exterior surfaces in cement mortar 1:4 and finished even and smooth without using extra cement, complete all as specified and directed.

Item No. 21 M&L for Rendering 5mm thick on fair faces of brick work or concrete surfaces of ceiling, chajja in CM 1:3 surface finished even and smooth without using extra cement, complete all as specified and directed.

Item No. 22 M&L for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper, over a coat of primer prepared to recieve distemper, complete all as specified and as directed.

Item No. 23 M&L for preparation of new surfaces of walls and applying two coat of cement based paint, complete all as specified and directed.

Item No. 24 M&L for preparing old surfaces of walls and applying one coat of cement based paint, complete all as specified and directed.

Item No. 25 M&L for preparation of newly plastered surface and applying three coats of white wash on ceiling, complete all as specified and as directed.

Item No. 26 M&L for preparation of old plaster surfaces of ceiling and applying one coat of white wash, complete all as specified and as directed.

Item No. 27 M&L for preparation of old treated/ decorated wood or wood based surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint of colour, shade & tint as approved by the Engr-in-Charge, complete all as specified and as directed.

Item No. 28 M&L for preparation of old painted steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint of colour, shade & tint as approved by the Engr-in -Charge, complete all as specified and as directed.

Item No. 29 M&L for preparation of old plastered or unplastered surfaces of walls, bricks, concrete surfaces etc. by brooming down or steel wire brushing; sraping down smoke soot, moulds, moss, efflorescent salts, trading oil and greasy spots etc and applying one coat of oil bound distemper, complete all as specified and as directed.

Item No. 30 M&L for washing, rubbing down and stopping of distempered and painted surfaces, including brooming down or steel wire brushing; scraping down smoke soot, moulds, moss, efflorescent salts, trading oil and greasy spots etc.; applying a coat of wall care putty smoothening the surfaces of walls, and applying two coat of Premium Acrylic smooth exterior paint, (of approved tint and shade), complete all as specified and directed.

Item No. 31 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing debrish and rubbish off the premises and stacking serviceable tiles, complete all a specified and as directed.

Item No. 32 M&L for 10mm thick light shade vitrified tiles, square or rectangular, polished area of tile not exceeding 0.36 sqm, in floors etc,in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bed or bedding layer in CM 1:4, complete all as specified and directed.

Item No. 33 All as per item No 32 but on vertical surfaces such as skirting incl including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tiles complete all as specified and directed.

Item No. 34 M&L for Non Skid ceramic coloured tiles, 7 to 8mm thick, (square/rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bed or bedding layer in CM 1:4, complete all as specified and directed.

Item No. 35 All as per item No 34 but on -ditto- but on vertical surfaces such as skirting incl including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tiles complete all as specified and directed.

Item No. 36 M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:4, complete all as specified and directed.

Item No. 37 All as per item no 36 but on vertical surfaces such as skirting incl including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tiles, complete all as specified and directed.

Item No. 38 M&L for glazed coloured ceramic tiles, first quality (or approved class, colour and design/ shade) of 300 x 200 x 7mm thick in vertical surfaces, as in dado/ skirting etc set & jointed in neat cement slurry & pointed in coloured cement to match with coloured tiles, over and including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tiles, complete all as specified and directed.

Item No. 39 M&L for glazed coloured ceramic tiles, first quality (or approved class, colour and design/ shade) of 450 x 300 x 7mm/ 600 x 300 x 7mm thick in vertical surfaces, as in dado/ skirting etc set & jointed in neat cement slurry & pointed in coloured cement to match with coloured tiles, over and including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tiles, complete all as specified and directed.

Item No. 40 Demolition of stone slabs of any description or thickness in floors/ walls laid bedded and pointed in any mortar etc. complete removal of debris outside MD land, complete all as specified and directed.

Item No. 41 M & L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing , including 15mm thick screed bed in CM 1:6, complete all as specified and directed.

Item No. 42 All as per item No 41 but on vertical surfaces such as skirting incl including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tiles, complete all as specified and directed.

Item No. 43 M&L for 16 to 18mm thick Granite (of any type) work (table rubbed and polished and exposed visible edge moulding/ rounding) in steps, jambs, pillars, window cills, cooking platforms and like in 15mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and directed.

Item No. 44 Demolition of un-reinforced Cement Concrete of any description and in any position not otherwise specifically provided for, separation of serviceable materials from the unserviceable, stacking the serviceable materials within 100 M and disposal of unserviceable materials, debris and rubbish to a distance not exceeding 100 M as directed by the Engineer in Charge, complete all as specified and directed.

Item No. 45 M&L for Plain cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in floors, foundations, filling & mass concrete, complete all as specified and directed

Item No. 46 M & L for coloured Rubber Moulded Chequred Cement Concrete tiles 300 x 300 x 25mm thick, set jointed and pointed in neat cement slurry in floors with grey cement and pigment over and including 15mm thick screed bed in CM 1:6, complete all as specified and directed.

Item No. 47 M&L for sand filling under floors or in foundations below interlocking tiles path including watering and consolidation, complete all as specified and directed.

Item No. 48 M & L for Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness M-40 Grade with grey cement and pigment, complete all as specified and directed.

Item No. 49 M&L for providing Precast cement concrete in type B-1, 1:2:4 (20mm graded aggregate) in Kerbs and edging to road, divider and foothpath etc incl necessary earthwork with plain fair faces, incl chamfered whethereing, throating etc and setting in cement mortar 1:4 complete with joints to match, complete all as specified and directed.

Item No. 50 S&F in repairs, curtain rod of stainless steel 25mm dia. including both side Stainless steel dome and brackets, complete all as specified and directed.

Item No. 51 S&F in repairs, Vitreous China wash down water closet pan (pedestal pattern), size 520 x 360 x 390mm including fixing bolts, PVC seat cover with mild steel chromium plated hinges (excluding flushing cistern and flush pipe), complete all as specified and as directed.

Item No. 52 S&F in repairs, vitreous china squatting pan, Orissa pattern, size 580 x 440mm white, with integral foot rests including connection to trap & to flushing pipe etc. including making good to floor etc, complete all as specified and directed.

Item No. 53 S&F in repairs, PVC valveless, syphonic action type, flushing cistern of 10 litres capacity, low level, white, with inlet, ball valve, float & handle including brackets, complete all as specified and directed.

Item No. 54 S&F in repairs, Vitreous China wash basin, white, flat back, size 550 x 400mm including PVC waste pipe, chain and plug and porcelain stopper, CP waste fitting 32mm dia and PVC bottle trap etc, complete all as specified and directed.

Item No. 56 S&F in repair chromium plated brass wall mixer 3-in-1 fancy type with provison for both hand shower and overhead shower complete with wall flange (without hand &over head Shower screwd down for15mm GI bore pipe, complete all as specifed and directed

Item No. 57 S&F in repair chromium plated brass Central hole basin mixer without popup waste system complete screwd down for 15mm GI bore pipe, complete all as specifed and directed.

Item No. 58 S&F in repair, 20mm dia brass chromium plated tubular towel rails, D type, 60cm long between flanges, complete all as specified and directed.

Item No. 59 S&F in repairs chromium plated health faucet, teliphonic type, with CP flexible arms and Jet, suitable to fixed and including 15mm bore CP angle valves etc, complete all as specified and directed.

Item No. 60 S&F in repair 110mm dia Cast iron nahani trap with CP grating including including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

Item No. 61 S&F in repair stainless steel kitchen plate rack size 600 x 900 x 150mm of approved pattern made out of stainless steel sheet 0.63mm thick sheet with round 8mm dia rods including hangine arrangements complete all as specified and as directed.

Item No. 62 S&F in repair S&F in repair 15mm size PVC connections internally threaded with PVC washer, PTMT nuts of length 450mm complete all as specified and directed.

Item No. 63 S&F Grating 100mm dia of CP with or without hole complete all as specified and directed.

Item No. 64 S&F in repair 15mm dia bib tap long body cast copper alloy (fancy type), chromium plated, with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule, complete all as specified and directed.

Item No. 65 S&F in repair 125mm size Brass Chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union, complete all as specifed and directed.

Item No. 66 S&F in repair 15mm dia brass chromium plated pillar tap, fancy type with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nut, capstan head, screwed for 15mm dia pipe, complete all as specified and directed.

Item No. 67 S&F in repair, Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with CP bracket guard & railing 60cm long, complete all as specified and directed.

Item No. 68 S&F in repair, sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with all plugs, washers, fittings and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specifed and directed.

Item No. 69 Taking up or down 15mm bore steel tubing and connections, including cleaning for re fixing complete all as specifed and directed

Item No. 70 S&F, laying and testing for 15mm bore GI tubing medium grade galvanised steel tubing including all fittings such as union, reducer, sockets, reducing bends elbows tee, checknuts, caps, plugs etc fixed to wall and ceilling or laid in floors, complete all as specifed and directed.

Item No. 71 Taking up or down 20mm bore steel tubing and connections, including cleaning for re fixing complete all as specifed and directed.

Item No. 72 S & F 20mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc, fixed to walls and ceilings or laid in floors, complete all as specifed and directed.

Item No. 73 S & F in repairs Stop/ angle cock 15mm bore cast copper fancy type chromium plated alloy screwed down high pressure with crutch or butter fly handle serwed both ends for iron pipe or for unions, complete all as specifed and directed.

Item No. 74 S & F in repairs two way Stop/ angle cock 15mm bore cast copper fancy type chromium plated alloy screwed down high pressure with crutch or butter fly handle serwed both ends for iron pipe or for unions, complete all as specifed and directed.

Item No. 75 S & F in reparis Stainless Steel Wall Mount Case with Soap Holder & Bruch Holder fixed to wall, complete all as specifed and directed.

Item No. 76 S & F in repairs, Hand shower 1.5 m CP Flexible SS Tube, 5 flow Hand Shower, adjustable wall hook, rubbit cleaning system, complete all as specifed and directed.

Item No. 77 S&F in reparis Flexible waste pipe for wash hand basin fittled to Wash Hand Basin incl all necessary brackets, complete all as specifed and directed.

Item No. 78 S & F in repairs 32/40mm PVC downpipe for kitchen sink fittled to Kitchen Sink incl all necessary brackets, complete all as specifed and directed.

Item No. 79 S& F in repairs flush Pipe of polyethylene of low or high density or PVC, 32mm dia, for low level cistern, complete all as specifed and directed.

Item No. 80 S & F in repairs Corner Glass Shelf of Size 320 x 320mm with Silver chromium finished border Oval Range premium quality, complete all as specifed and directed.

Item No. 81 Hacking out old broken glass (any thickness, size, quality or description) from metal frame incl punching or drilling out old glazing pins/ spring clips and providing and fixing new ones complete all as specifed and directed.

Item No. 82 M&L for 4mm thick sheet glass, ordinary quality and glazing with oil putty and fitted in wooden/ steel window in square n exc 0.5 Sqm in each pane, complete all as specifed and directed.

Item No. 83 M&L for 4mm thick sheet figured glass, pin headed type and glazing with oil putty in square n exc 0.5 Sqm in each pane, complete all as specifed and directed.

Item No. 84 S&F in repairs Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specifed and directed.

Item No. 85 M & L in fixed in repairs 18/19mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specifed and directed.

Item No. 86 S&F in repair PVC water tank covers premium quality fitted to tank. Make : Syntex or equivalent water tanks of Cap 500 ltrs to 1000 ltr ,complete all as specified and directed.

Item No. 87 S&F in repair Ball valves 15mm high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed, complete all as specifed and directed.

Item No. 88 S&F in repair Ball valves 20mm high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed, complete all as specifed and directed.

Item No. 89 S&F in repair 15mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specifed and directed.

Item No. 90 S&F in repair 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specifed and directed.

Item No. 91 S & F in repairs PVC size 110 x 110mm Nahani Trap, complete all as specifed and directed.

Item No. 92 S&F in repair 1000 litres capacity Rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) hoisted and fixed in position including removing the existing water tank complete all as specifed and directed.

Item No. 93 S&F in repair 500ltr capacity rotational moulded polythyiene water storages tanks (cylindrical vartical with closed top) hoisted and fixed in position including removing the existing water tankall complete all as specified and as directed.

Item No. 94 M&L for Framed work such as grills, gratings, etc. with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290. Gde-E-165 complete all as specifed and directed.

Item No. 95 Taking down rain water pipes including all fittings any size and pattern complete all as specifed and directed.

Item No. 96 S &F 110mm bore PVC (SWR) soil, waste and vent pipes single socked in any length with rubber ring joints fixed to walls, complete all as specifed and directed.

Item No. 97 S&F in repairs 110mm bore PVC (SWR) bends of any radius complete all as specifed and directed.

Item No. 98 S&F in repairs 110mm PVC (SWR) junction single, (Single T) equal or unequal complete all as specifed and directed.

Item No. 99 S&F in repairs 110mm PVC (SWR) branch piece, double (double Y) equal or unequal complete all as specifed and directed.

Item No. 100 S &F 75mm bore PVC (SWR) soil, waste and vent pipes single socked in any length with rubber ring joints fixed to walls complete all as specifed and directed.

Item No. 101 S&F in repairs 75mm PVC (SWR) bends any radius complete all as specifed and directed.

Item No. 102 S&F in repairs 75mm PVC (SWR) junction single, (Single T) equal or unequal complete all as specifed and directed.

Item No. 103 S&F in repairs 75mm PVC (SWR) branch piece, double (double Y) equal or unequal, complete all as specifed and directed.

Item No. 104 Taking down chowkats or frame of any description exc 1.5 Sqm each and n.exc 4Sqm (without taking off shutters from the frames) & remove off the premises, complete all as specified and directed.

Item No. 105 Taking down Shutters of any description exc 1 Sqm but n. exc 2 Sqm each of any description, complete all as specified and directed.

Item No. 106 Taking down chowkats or frame of any description n.exc. 1.5 Sqm each (without taking off shutters from the frames) & remove off the premises complete all as specified and directed.

Item No. 107 Taking down Shutters of any description n. exc 1 sqm each of any description complete all as specified and directed.

Item No. 108 S&F Pressed steel door frame for single door, size 165 x 60 x 1mm with one rebates incl necessary fixing lugs, hinges, lock strike plate, holdfast (size 25mm x 3mm) of length 30 cm) etc., including Cutting holes in brick walls built in cement mortor for inserting holdfasts and making good dismantled portion in cement mortor 1:3 or cement concrete 1:2:4 Type B-1, depth of embedded portion of holdfasts exc. Half brick but not exc. One brick from the face of the jamb intl the wall, complete all as specified and as directed.

Item No. 109 M & L PCC 1:2:4 type B0(12.5mm graded) aggregate for filling in pressed steel door framed complete all as specifed and directed.

Item No. 110 S& F Second class hard wood plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specifed and directed.

Item No. 111 S & F 35mm thick second class hardwood rail and style, Plain, framed, panelled shutters Plain framed, panelled shutter (two panel) with lock rail and panel of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specifed and directed.

Item No. 112 S&F Solid PVC door frame of size 50mm, 47mm made out of 5mm plain colour PVC sheet rinforced with MS Square tube suppling and fixing in opening as per specification complete all as specifed and directed.

Item No. 113 Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip if 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bootom rail on either side & as gap insert for top rail and bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling and fixing in the frame at site as per specification complete all as specifed and directed.

Item No. 114 S&F 35mm thick Flush shutters, solid core construction, with block board core & plywood face panels, commercial type on both sides complete all as specified and directed.

Item No. 115 S & F 30mm thick 2nd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass gauge etc with cut and mitred beads for securing glass etc size of member of shutter as specified in SSR Part-I section 8 and clause 8.24 (a), complete all as specifed and directed.

Item No. 116 S & F 35mm thick 2nd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass gauge etc with cut and mitred beads for securing glass etc size of member of shutter as specified in SSR Part-I section 8 and clause 8.24 (a)

Item No. 117 S & F of Powder coated aluminum three track sliding shutters window with frame consisting two Glazed shutters and one guazed shutters(with wire mesh), each shutter width one half of the length of window with the following specifications and making good the adjacent surfaces with brick work and plaster. (i) Three way track for sliding shutters of cross section 91.80mm x 31.75mm x 1.00mm thick. (ii) Sliding shutter frame of cross section 40 x 18 x 1.00mm. (iii) Aluminium glazing strip of size 18.2 x 16.66mm. (iv) 4 to 5 mm thick float glass superior quality make Modi float for two shutters. (v) EDPE rubber gasket for fixing glass. (vi) Locking cleat per shutter -01 No. (vii) Two nos sliding rollers per shutter. (viii) Rubber shock absorber 03 No per shutter. (ix) Aluminium wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm for one shutter. (x) Fixing screws for frame with wall – 06 No per window. (x) Fixing screws for frame with wall - 06 No per window.

Item No. 118 S & F Powder coated Aluminium ventilator, fixed type without sash bar, aluminum section weighing 0.55 Kg/ RM including necessary joining cleats, glazing clips, rubber packing, anodised aluminum snap beading, screws etc. including 50% of bottom portion is fixed with 4mm pin headed glass and balance 50% of top portion is fixed with 4mm thick pin headed glass lowers and cover with 0.36mm dia stainless steel wire mesh at top portion complete all as specifed and directed.

Item No. 119 S&F 150mm size aluminium, anodised barrel tower bolt of extruded section, complete all as specifed and directed.

Item No. 120 S&F 125mm size aluminium, anodised barrel tower bolt of extruded section complete all as specifed and directed.

Item No. 121 S&F 300mm length, aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specifed and directed.

Item No. 122 S&F 120mm size, butt hinges, heady weight, cold rolled mild steel complete all as specifed and directed.

Item No. 123 S&F 100mm size, butt hinges, medium weight, cold rolled mild steel complete all as specifed and directed.

Item No. 124 S&F 150mm size extruded aluminium alloy handles, fabricated type, complete all as specifed and directed.

Item No. 125 S&F 125mm size extruded aluminium alloy handles, fabricated type, complete all as specifed and directed.

Item No. 126 M&L for Preparation of new wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specifed and directed.

Item No. 127 S&F in repairs 18mm thick factory made PVC sheet one side pre-laminated sheet ktichen cabinet shutter. The 18mm thick sheet shutter bent at 90 degree and finish all edges at level for marking edge lipping bending for 0.5mm thick PVC sheet lipping at all four edges using bonding tape etc complete all as per specified and directed.

Item No. 128 S & F in repairs factory made PVC shelf/ partition of required size consisting of panel of 18mm thick required size consisting of panel of 18mm thick celuka PVC ply and for supporting the hold of shelf/ partition and shall provided 3 edges in size 18mm x 18mm as per required lenght the front side of the edge visible in the front of the shelf/ partition to be edge lipped by 18mm widht x 1mm thick PVC sheet of density 600 kg/ cum manufactured by ISO 9001-2015 Certified Company, using solvent cement complete all as specifed and directed.

Item No. 129 S&F stainless steel shelf closing hinges 75mm size for PVC door shutters complete all as specified and directed

Item No. 130 S&F 50 x 15mm size magnet door catcher for closing for PVC door shutter complete all as specifid and directed.

Item No. 131 S& F 100mm size MS mat/ glossy finish handle complete all as specfied and directed.

Item No. 132 Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc, separation of serviceable materials from the unserviceable, stacking the serviceable materials within 100 M and disposal of unserviceable materials, debris and rubbish to a distance not exceeding 100 M, complete all as specified and directed.

Item No. 133 M&L for Brick work with sub-class 'B' bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:4 using old size bricks, complete all as specified and directed.

Item No. 134 M&L for brick work with modular size kiln well burnt sub-class 'B' bricks, straight or curved on plan to any radius in half brick thick wall built in CM 1:4, complete all as specifed and directed.

Item No. 135 Demolition of un-reinforced Cement Concrete of any description and in any position not otherwise specifically provided for, separation of serviceable materials from the unserviceable, stacking the serviceable materials within 100 M and disposal of unserviceable materials, debris and rubbish to a distance not exceeding 100 M, complete all as specified and directed.

Item No. 136 M&L for PCC 1:5:10 type E2 using 40mm graded aggregate as in Mass concrete in sunkan treatment complete all as specifed and directed.

Item No. 137 M&L for water proofing treatment to sunken surfaces of the slab in following sequences:-

Item No. 137 (a) Slope correction by using M-20 (Nominal Mix) concrete minimum 25mm thickness at one end and a slope of 1:20 by using 12.5mm graded stone aggregate with integral water proofing Chemical PIDI PROOF-LW mixed in proporation 200ml/ 50 Kg cement of DR Fixit of Pidilite Industries Ltd or STP No 1 (liquid) of STP Ltd in proporation 200ml/ 50 Kg cement or equivalent as per manufacturer instructions, complete all as specified and directed.

Item No. 137 (b) PCC padding with cement concrete 1:1.5: 3 type A 0 (using 12.5mm graded stone aggregate) 25mm thick with integral water proofing compound "Dr Fixit" manufactured by M/S Bouchemic or equivalent as per manufacturer instructions, complete all as specified and directed.

Item No. 137 (c) Vertical sides plastered in CM 1:3, 15mm thick with WPC and 72 hours testing for water tightness by ponding of water, complete all as specified and directed.

Item No. 137 (d) Application of two coats proof coats black manufactured by M/S Dr fixit or equivalent as per manufacturer instructions all over and testing again for water tightness by ponding of water for 72 hours, complete all as specified and directed.

BHATIA ASSOCIATES

ms shrilaxminarayan and sons

M/S Ashish Construction

Jamna Constructions

KAILASH CHANDRA KHANDELWAL