CAD work for Lift Irrigation Scheme Bhaleth in Tehsil Sujanpur Distt. Hamirpur HP Sub Head Laying, jointing and testing of HDPE pipe line at various chak and C/O outlet chamber at various places

Amount

Excavation in foundation and trenches etc. (for laying pipes and pits) in all kinds of soils such as pick work, jumper work, blasting in soft/hard rock, chiselling/wedging out of rock/where blasting prohibited)saturated soil stacking the excavated earth within all leads and lifts clear from the edge of excavation and then returning the stacked soil in 15cm layers when required into plinth sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposting of all surplus excavated earth as directed within all leads and lifts including uprooting of trees dressing of beds, and sides and preparation of sub-grade, restoration of unmetalled /metalled/ paved surfaces to its original condition including soring, strutting, timbering and dewatering where ever houses, fixing caution boards, crossing over trenches and to the entire satisfaction of the Engineer-in-charge.

pick work and jumper work

Laying& jointing in trenches HDPE pipes of following diameter & classes as per IS-4984, PE-80 and jointing the pipes through push type compression joint hydraullicaly operated machine up to 110 mm diameter and butt fussion (heat fusion process) above 110 mm diameter i/c necessary fittings,bends,tees& reducers febricated in accordance with IS 8360 & IS8008 with latest ammendments & shall be provided conferming to code IS 8008 & IS 7634, stud ends will be welded on pipes & MS flange shall be provided with slip on covered by epoxy coating/plastic powder. The flange should be confirm to ANSI B 16.5 with necessary nuts & bolts. Jointing shall be complete in all respect i/c testing at site upto entire satisfaction of Engineer-in-Charge i/c all fitting

(i) 110 mm dia PN 4 Class, PE-80

(ii) 125 mm dia PN 4 Class, PE-80

(iii) 140 mm dia PN 4 Class, PE-80

(iv) 160 mm dia PN 4 Class, PE-80

(v) 180 mm dia PN 4 Class, PE-80

Providing & Fixing Cast Iron double flanged type sluice valve of reputed & approved make like kirloskar/Kilburn/IVC/Leader/Bir/Sant etc. on distribution system of conferming to IS: 780-1984 with latest ammendments of appropriate class, diameter and capable to with stand the requiste nominal seat pressure 10 Kg/Sqm i/c testing & upto entire satisfaction of Engineer-in-charge

(i) 140 mm dia PN 4 Class, PE-80

(ii) 160 mm dia PN 4 Class, PE-80

(ii) 180 mm dia PN 4 Class, PE-80

Providing and laying cement concrete 1:4:8(One cement :Four sand : Eight graded stone aggregate 40mm nominal size and curing complete excluding the cost of form work in foundation and plinth within all leads and lifts.

Providing and laying cement concrete 1:2:4(1 cement:2sand:4graded ston aggregate 20mm nominal size) and curing complete excluding the cost of form work in foundation and plinth within all leads an lifts.

Providing and Laying precast slab in nominal cement Concrete(1:1.5:3) 1 cement: 1.5 sand: 3 graded stone aggregate and curring complete excluding cost of form work and reinforcement for RCC work in foundation & plinth as per direction and to the entire satisfaction of the Engineer-in-Charge.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm, so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battons and ballies, height of propping and centering below supporting floor to ceiling not exceeding 4.00mtrs. and removal of the same for in-situ-reinforced and plain concrete work in:-

(i) Vertical surface such as walls (any thickness) partitions and the like including attached pillasters,buttresses, plinth and string courses and the like within all leads and lifts.

Boulder filling at bottom of 350mm dia Hydrant Chamber

Providing & Fixing of Fitting and accessories Complete in all leads and lifts.

(a) 75 mm dia PN4 HDPE pipes

(b) 75 mm dia PN 6 HDPE pipe end

(c) 75 mm dia PN 6 HDPE 90̊ pipes bend

(d) 75 mm dia PN 6 HDPE QC pump connector

Providing and laying mild or tor steel reinforcement for RCC work including bending and placing in position complete upto floor two level Tor steel in all leads and lifts including carriage and as per direction and to the entire satisfaction of the Engineer-in-charge.

Providing & fixing in position RCC pipe of following dia, class & length for outlets

RCC pipe of 900 mm dia NP 2.0

RCC pipe of 350 mm dia NP 2.0

Providing & Fixing 80 mm dia control/Sluice Valve leader/Kirloskar make as per direction and to the entire satisfaction of the Engineer-in-charge.

Steel work welded in built up sections, trusses, and framed work including cutting ,hoisting, fixing in position and applying a priming coat of red lead paint and Two coat part in grating, framed guards bars, Ladders, railings,bars brackets and similar works as per direction and to the entire satisfaction of the Engineer-in-charge.

Miscellanious for locking arrangments & other accessories as per direction and to the entire satisfaction of the Engineer-in-charge.

abhishek khajanchi

SUNIL KUMAR

NISHANT KUMAR

RAJE ENGINNERING WORKS

Gulrez Mohammed

Vikas Dogra

ANEESH KAUSHAL