200KVA Diesel Generator Set

Amount

31.280.1J: Supplying of 3 phase, 415 volts, 50 cycles, 0.8 power factor for electric starting diesel generator comprising the following units:-(Kirloskar/ Leyland/ Ruston/ Greaves Cotton/ Cummins make) water cooled and shall be of multi stroke, multi cylinders, cold starting, developing not less than 254 BHP under normal temperature and pressure. The engine shall conform to I.S. 10002 with latest amendments. It shall be capable of taking 10% over load for one hour in every 12 hours of continous operation including 6 Nos. of anti vibration pads.The engine shall be complete with the following accessories: Electrical starting provision, engine cooling fan, fuel and lubricating oil filters, oil bath, air filter, lub oil pressure gauge 350 litres capacity fuel tank mounted with engine, hour meter with exhaust manifold, flexible pipe, 12/24 volts electric starting equipment complete with starter, alternator and two numbers of 12 volts with 25 plates battery of make AMCO /STANDARD/EXIDE/ DAGANITE (with Guarantee cards) of adequate capacity and low lubricating oil pressure/ high temperature varying engine shut down devices.The Acoustic enclosure shall have the following: Acoustic enclosure shall be powder coated and fabricated out of 16 SWG CRCA MS sheet. The silent canopy shall be of nut bolt type construction ....

31.263.1 Making earth pit of G.I. pipe for earthing in earth pit with 40mm dia. G.I. pipe medium class of length 3.05m perforated with 46 Nos of 12mm dia. holes, pipe lowered in bore holes of 150mm dia. and filled in with charcoal and salt in alternative layer of 300mm, the top of G.I. pipe shall be clamped. Earth pit shall be provided with 60cm dia precast ring with 60cm depth alround,covered with R.C.C. precast slab etc. as per I.E. standards.

31.281.1D Providing and fixing of suitable M.S.exhaust pipe including 2 Nos. of M.S.bends (long), 7 Nos. of M.S. flanges, M.S. pipe Class B - 5 Rm as flexible exhaust pipe. The rate is inclusive of transportation charges for shifting of welding machine and gas cutting set to site, consumption of welding rod 10 SWG and cutting gas, providing fasterners of 10mm bolts / nuts / washers and flange gaskets including labour charges etc. as per IE standard.125 mm dia exhaust pipe (From 200 KVA to 250 KVA)

31.267.1A Supplying and fixing of copper flat (25 x 3mm) for earthing arrangements including bolts and nuts etc.

31.259.1H Supplying of 3.5x240 sqmm underground cable (Paragon/ suncab/ Empire) complete.-(above 160KVA to 200KVA Genset).

31.260.1G Laying of UG cable and providing termination of cable joint with suitable cable gland,cable socket etc. complete - 3.5 x 240 sqmm cable.

31.283.1 Providing and fixing of fire safety equipments comprising 1 No. of 4.5 kg of CO2 fire extinquisher 1m x 2m x6mm thick rubber mat shock proof of superior quality with two numbers of 10 litres capacity fire buckets (red colour) with M.S. stand arrangements etc.

31.284.1C Providing and fixing of 4 pole change over switch of STANDARD/ HAVELLS/KUNDAN / GEM make including M.S. frame as per I.E. standard.-400 Amps (Above 100 KVA)

31.282.1 Providing and laying of aluminium cladding with 50 mm thick glass wool slab with chicken mesh and covered with 24 SWG aluminium sheet (the rate includes double calculation for flanges & bends) as per I.E. standards.

31.285.1C Charges for transporting, erection, testing and commissioning of generator set excluding foundation,but including mechanical and other unskilled wages for installation of equipment, wiring from generator set to panel board and change over switches, handling charges, purchase of spares if any required for the installation and commissioning, the cost of fuel and other materials for a trial run of 6 hours. This rate also includes for testing and commissioning of generator set as specified, obtaining approval of Central Electricity Authority (CEA), payment for CEA inspection/Licence fees or any other charges and fulfilling other requirements and conditions laid down by CEA-from 125 KVA to 200 KVA

2.8.1 Earthwork in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed , within a lead of 50m - all kinds of soil.

2.27 Supplying and filling in plinth with river sand under floors, including watering ,ramming consolidating and dressing complete.

4.1.3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size)