REPAIR TO TILES, FLOORING, JOINERIES, AC SHEET ROOF IN COOK HOUSES IN WING - I AND V AT ARTY CENTRE UNDER GE NASIK ROAD

Amount

Dismantling asbestos cement (corrugated,semi corrugated)sheets in roof covering

Dismantling wrought iron or mild steel work of any description not otherwise provided for including gas cutting, welding etc.

Dismantling of stone slabs & tiles of any description or thickness (except ceramic tiles) in floors, aprons etc laid bedded & pointed in any mortar complete all as specified and directed

Demolition of brick work or stone boulder masonry built in cement mortar or cement lime mortar including all quoins, arches, pillers etc but including ashlar facings, dressed stone work and precast concrete articles

Taking down cement plaster on brick or stone wall etc including raking out joints hacking for keys scrubbing down with water etc. including removing all the debris out side MD land

S & F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and making good to wall and roof joint.

S & F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges, hips, valley gutter, drip and straight flashing.

S&F rolled mild steel Joist, channel, angle, flat sections, fixed independently, without connecting plates, or M S tubular sections etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) grade Fe 290( E-165) all as directed by Engr-in-charge

M&L for preparation of new steel surfaces and applying two coat of synthetic enamel paint over one coat of red oxide primer on new steel surfaces, girth or width exc 10cm

M&L for preparation of old painted of steel surfaces and applying two coat of synthetic enamel paint on steel surfaces, girth or width exc 10cm complete all as specified and directed.

S&F Mild steel Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 ® complete all as specified and directed

M&L for Screed bed or bedding layer of cement mortar 20 mm thick for laying floors finishes in cement mortar 1:6.

M&L for cement concrete Type D2 1:4:8 (40 mm graded aggregate) 75 mm thick as in sub base

M&L for machine cut kota stone slab 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed. Note: screed bed layer, cement motar measured seperately

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with gray cement slurry with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

S & F machine cut cudappa stone slab 16-18 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete Note: screed bed layer measured seperately complete all as specifed and directed

M&L for granite (of any type)work (table rubbed and polished) 18 mm thick in steps,jambs,pillars,cooking platforms and like in cement mortar 1:4 incl pointing in white cement 1:2 using marble dust with admixture of pigment to match the shade of granite

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations

M&L for rough dressed shahabad stone slab 20 to 25 mm thick laid beded and jointed and pointed in CM (1:3) in floors complete all as specifed and directed Note : Cement mortar screed bed layer shall be measured & paid separately

- ditto all as per item no 19 above but except stone

M&L for Brick work with fly ash bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6 with old size bricks.

M&L for Brick work with fly ash bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 with old size bricks.

M&L for polygonal rubble mesonry, uncoursed well bonded bedded and solidly hearted built in CM 1:6 complete all as specified and directed.

Ditto as Item no-23 but except stones

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, Hammer dressing with maximum depression on face from straight edge held against the dressed surface n exc. 20mm as specified, of random rubble walling,uncoursed or brought upto courses

M&L for keyed pointing of CM 1:4 to random or polygonal rubble;uncoursed or brought upto courses complete all as specified and directed.

M&L for rendering 5 mm thick (1: 3) on fair faces of concrete surfaces incl preparation to new surfaces on ceilings finished even and smooth without using extra cement

M&L for rendering 15 mm thick cement plaster on than fair faces of brick work or concrete surfaces in CM 1:4 rendering is to be finished even and smooth without using extra cement adding water proofing compound 3% by weight of cement (water proofing compound shall be measured and paid separately)

M&L for rendering 15 mm thick (1: 6) on stone masonry or other than fair faces of brick work surfaces finished even and smooth without using extra cement

M&L for rendering 10 mm thick (1: 6) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement

Supply only intergral water proofing compound

M&L for Preparation of new plastered surfaces and applying three coats of white wash on ceiling surfaces all as directed

M & L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

M & L for Complete removal of existing treatment on wall surfaces including preparation (i.e. brooming down plastered / unplastered surfaces complete) and Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade Paint or equivalent complete all as specified and directed.

Dismantling wall and ceiling boards( Fibre, pulp, insulation etc) or insulation boards any thickness including cover fillets complete all as specified & directed.

S&F interlocking aluminium powder coated snap grid consists of main Tee runners of size 38mm x 25mm x 1.00 mm spaced 1200mm centre to centre and cross Tee of size 25mm x 25mm x1.00mm, 1200 long spaced between the main Tee at 600mm centre to centre to form a grid of 1200mm x 600mm and provide a secondary cross Te 25mm x 25mm x 1.4mm (of length 600mm) to be interlocked of the centre of 1200mm x 600mm panel to form a grid of 600mm x 600mm and wall angle 25mm x 25mm x 1.5mm . Aluminium alloy extruded section shall be aluminium anodized ( minimum 15 micron) and shall conform to IS 733, IS 1285 and IS 737, and providing and fixing with Hangers of 4mm dia GI (upto 1200mm length ) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x 3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long size of grid 600 x 600mm complete all as specified and S&F non asbestos cement building board 4mm thick of make E board classic of M/s Everest industries Ltd or equivalent make as approved, “in ceiling fixed with screw as per manufacturer instruction”

S&F in repairs Vitreous china squatting pan ,'Orissa' pattern, size 580x440 mm white,with integral foot rests (excluding flushing cistern and flush pipe)

S&F of PVC(SWR) 'P' trap of 125/110 mm bore

Dismantling floor hearth or wall tiling including cement mortar bedding (But not backing) removing serviceable tiles to store and rubbish off the premises.

M&L for 10 mm thick rendering in CM 1:4 on brick masonary or concrete rough finished surfaces as backing coat

M&L for coloured glazed ceramic tiles 300 x 200 x 7mm / 300 x 450 x 7-8mm thick in vertical surface, set and jointed in neat cement slurry & pointed with white or coloured cement to match

M & L for 15mm thick Screed bed or bedding layer in cement mortar 1:6 for laying floors finishes

M&L for non-skid coloured ceramic tiles 7 to 8mm thick square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tile all as specified and directed by Engr-in-charge

S&F in repairs bib taps standared of PTMT 15mm bore dia any colour high presure screwed for iron pipe of Make Prayag fixed (minimum weight 90 gms) complete all as specified and directed

S&F in repairs PVC valveless,symphonic action type,flushing cistern ,low level white,with inlet,ball valve,float and handle including brackets of 10 ltrs inclluding flush pipe of polyethelene of low or high dencity or PVC, 32 mm dia all as specified and direcetd.

S & F PVC connections 15mm size with PTMT nuts of length 450mm.

S&F in repairs 40mm size waste fittings, brass chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed.

S&F in repair stop valve, 15mm bore dia PTMT of any colour high pressure screwed for iron pipe and fixed (Minimum weight 90 gms) complete all as specified and directed.

Taking up or down 15 mm dia tubes galvanized iron and connections and fittings or removal from site as incl cleaning for refixing where directed complete all as specified and directed.

- ditto All per Item no. 49.00 but 20 mm dia

- ditto All per Item no. 49.00 but 25 mm dia

Re-fixing only 15 mm dia tubes galvanized iron and connections fixed to walls or laid in floor supplying & fixing new fittings such as socket, bends, elbows nipple, union etc all as specified and directed.

- ditto All per Item no. 52.00 but 20 mm dia

- ditto All per Item no. 52.00 but 25 mm dia

S&F 15 mm dia tubes medium grade, galvanized with iron all fittings fixed to walls, ceiling and laid in floor of complete all as specified and directed.

- ditto All per Item no. 55.00 but 20 mm dia

- ditto All per Item no. 55.00 but 25 mm dia

S&F of 75 mm dia PVC(SWR) pipes single socketed,in any length with rubber ring joints fixed to walls

- ditto All per Item no. 58.00 but 110 mm dia

S&F of 75 mm dia PVC(SWR) bends

- ditto All per Item no. 60.00 but 110 mm dia

S&F of 75 mm dia PVC(SWR) Vent cowl

S&F 50mm dia low density polyethylene pipes(LDPE) of pressure rating 6 Kgf/cm2 fixed complete to walls as directed by Engr-In-Charge

S&F 75mm PVC(SWR) floor trap,plain with grating including jointing with solvent cement

Taking down carefully existing bitumen tarfelt incl. Screed and cleaning of surfaces of roof etc. With wire brush incl. Flashing and junctions of parapets/kerb walls etc. And removing of the rubbish to a distance exc. 500 metres but not exc. 1.5 km and deposting where directed.

M&L for screed 15mm thick in cement mortar (1:4) on concrete surfaces mixed with water proofing liquid and smooth finished and smooth(without using extra cement).

M&L for Waterproofing on roof including flashing and junctions of parapet, kerb, wall etc. as under:- (a) Applying bituminous primer on cleaned and dried surface @ 0.20 Kg/Sqm. (b) A coat of hot blown type bitumen of grade 85/25, applied hot at the rate of 1.20 kg/sqm. (c) Laying on primed surface by thermo fusion (torch application) 3mm thick APP based polymeric water proofing membrane weighing not less than 3.50kg/sqm and reinforced with polyester non woven fabric (not less than 150 gms/sqm). (d) Painting the exposed APP membrane surface with bituminous aluminium paint @ 0.15 Kg/Sqm.

Taking down chowkat or frames with shutters (without taking off shutters from the frame not exc. 1.5 Sqm each.

Taking down chowkat or frames with shutters (without taking off shutters from the frame) exc. 1.5 Sqm but n exc 4 sqm each.

S&F aluminium anodised powder coated (min thickness 50 microns) frame for doors, windows, ventilators, complete all as specifed and directed

S&F Aluminium anodised powder coated door shutters aluminium section weighing not less than 0.55 kg per mtr incl necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges anodised aluminium snap beading, screws etc complete all as specifed and directed

S&F Aluminium anodised powder coated window and ventilator shutter, sliding type without sash bar, alumn section section weighing not less than 0.55 kg per mtr incl necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specifed and directed

S&F Sheet glass ordinary quality 5.5 mm thick exc 0.5 sqm each pane with Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specifed and directed

S&F Sheet glass ordinary quality 4.0 mm thick n. exc 0.5 sqm each pane with Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specifed and directed

S&F floor door stopper of aluminium alloy body & tongue, anodised, with hard drawn steel spring of 140mm size fixed in floor complete all as specified and directed.

S&F Aluminium body door closer hydraulically regulated, designation No. 3 universal type, suitable for door shutters of 851 oto 1000 mm in width and of weight between 61 to 80 Kg.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain coloured PVC sheet reinforced with MS square tube S&F in opening as per specification and drawing.

S&F factory made soild panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & plain colour PVC sheets for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification and drawing.

S&F MS butt hinges 100mm size medium weight complete all as specified and directed

S&F aluminium alloy barrel tower bolt 150 mm long

S&F 150 mm aluminium alloy handels cast/plate type

S&F SS butt hinges 100mm size medium weight complete all as specified and directed

S&F II nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, sup-plied and fixed

S&F IInd class hard wood factory made Glazed and ske- leton shutters 35 mm thick, open rebated and prepared to receive glass, gauze, etc. (divided in to square with sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mi-tred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Sec-tion 8, cla-use 8.20 (a); supplied and fitted to chowkats.

S&F IInd class HW 35mm thick plain framed factory made panelled shutters (two panel) with lock rail, panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and style as per IS-1003 (Part I) Kiln, Seasoned and chemically pressure treated.

M&L for preparation of new wooden surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

S&F aluminium alloy anodised sliding door bolt 300mm long with hasp & staple (bolt type) and fixing chops of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast alluminium alloy abd fixed

M&L for 18 mm thick PVC sheet prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side with white lamination including necessary locking device, catches suitable for kitchen cabinets and 4 mm thick PVC beading on all edges as in kitchen cabinets etc complete all as specified and directed.

S&F Continuous (piano) hinges 30mm flap size (When open) of MS and fixed with wooden frames with MS screws complete all as specified and directed by EIC

S&F Stainless steel wire cloth, 0.36 mm dia of wire and average width of aperture 1.40 mm and fixed with stainless wire staples.

S&F Stainless steel wire cloth, 0.36 mm dia of wire and average width of aperture 1.40 mm and fixed with stainless wire staples in repairs

Disconnecting existing tanks of exc 500ltrs but n. exc 1000Ltrs, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing, etc. measured separately)

Dismantling water tanks of size exc 500Ltrs but n. exc 1000Ltr and removing to store

Rotational moulded polyethylene 1000 Ltrs capacity water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I

S&F 25mm bore dia Nipple suitable for HDPE water tank. (Minimum weight 25mm- 65gms)

S&F 25mm bore dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed

M&L for rubber moulded machine pressed precast inter locking paver block with gray cement any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-25 grade laid on 30mm thick stone dust cushioning laid dry to the profile complete all as specified and directd

M&L for applying 3mm thick wall care putty on wall (Birla white) complete all as specified and directed by EIC.

M&L for preparating newly plastered surfaces of walls and applying two coats of OBD over one coat of chalk whitning, prepatory to distempering complete all as specified and directed.

M&L for preparation of old painted surfaces of any description by complete removal of existing treatment and applying two coats of Oil bound distemper over a coat of primer on walls complete all as specified and directed.

M&L for preparation of newly plastered surfaces of any description of walls applying three coats of whitewash on undecorated surfaces of walls complete all as specified and directed.

M&L for preparation of old painted surfaces of any description by complete removal of existing treatment and applying three coats of whitewash on undecorated surfaces of walls complete all as specified and directed.

M&L for preparation of old painted surfaces of any description by complete removal of existing treatment and applying three coats of whitewash on undecorated surfaces of ceiling complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and any position not otherwise specially provided for

M&L for cement concrete type C2 1:3:6 (20 mm graded aggregate) 75mm thick in plinth protection complete all as specified and directed including filling of expansion joints with mix.

Demolition of cement concrete reinforced (reinforcement cut as required to facilitate demolition) of any description and any position not otherwise specially provided for

M&L for providing cement concrete type B1 1:2:4 (20 mm graded aggregate), in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses,lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed

S&F Mild steel bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hookingends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality confirming to TMT bars.

Ditto, as per item No 108 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders

M&L for cement concrete type C2 1:3:6 (40 mm graded aggregate) in surface channels and drains complete all as specified and directed.

Extra for forming fair finished drain or channel 45 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc

Cutting holes exceeding half brick but n. exc full brick depth in brick walls in stone/Brick walls built in cement mortar or in cement lime mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4

S&F Mild steel works in Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165

M&L for Preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described, and treated with tar or coal tar black paint

Repairing broken edges of RCC chajjas, roof projections, fins, facia and similar works by dismantling of loose and damaged/ disintegrated portion of edges (cross sectional area not exceeding 150 sqcm) and cement mortar 1:4 or cement concrete 1:1½:3 type A0 and chicken wire mesh with nails (to hold fresh mortar/concrete) including necessary formwork etc. and scaffolding for work upto four storied buildings and finishing the surface by white wash or cement base paint to match the surface with existing work.

S&F in repairs tubular rail curtain rod 20mm dia, brass chroium plated complete all as specified and directed by EIC.

S&F in brass chromium plated fancy type brackets for 20mm dia tubular curtain rod including fancy type ends complete all as specified and directed by EIC.

S&F in repair stainless steel sink made of stainless steel 1mm thick with out drainage board including plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing contilever brackets and connecting union to pipe overall size 495mm x 420mm, bowl size 410mmx330mmx160mm complete all as specifed and directed

NOTE : - AMOUNT OF SCHEDULE OF CREDIT RS 14,581.00 WILL BE DEDUCTED FROM TOTAL AMOUNT OF BOQ.

M/S SAMEER SUBHASH PATANI

Vishal Constructions

Srujan Associates

Alpha Construction

M/S K. K. Construction

Abhiraj Enterprises

SVT ENGINEERS AND CONTRACTOR.

A V S Builders

Bidder Name

Vishal Constructions

A V S Builders

M/S SAMEER SUBHASH PATANI

SVT ENGINEERS AND CONTRACTOR.

M/S K. K. Construction

Alpha Construction

M/s. JBSR ENTERPRISES.

Srujan Associates

Abhiraj Enterprises