02/EE/C/EC/MTNL/2020-21/NIT

Amount

Dismantling wooden boardings in lining of walls and partitions,excluding supporting members but including stackin g within 50 metres lead :Thickness above 10 mm up to 25 mm

Dismantling steel work manually/ by mechanical means in built up sections without dismembering and stacking within 50 metres lead as per direction of Engineer-in-charge.

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mm

Dismantling tile work of wall & dado laid in cement mortar including stacking of useful material with in 50-meter lead and disposal of unserviceable materials in authorized municipal dumps etc. all complete as per direction of Engineer-in-charge:For thickness of tiles less than 10 mm.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.In cement mortar

Removing mortar from bricks and cleaning bricks including stacking within a lead of 50 m (stacks of cleaned bricks shall be measured):From brick work in cement mortar

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand)

Extra for half brick masonry in superstructure, above floor V level for every four floors or part thereof by mechanical means.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand).

12 mm cement plaster of mix :1:4 (1 cement: 4 coarse sand)

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Dismantling C.I. or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead :100 mm dia pipe

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

75 mm diameter

110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conformingto IS : 13592 Type A, including jointing with seal ring conforming toIS : 5382, leaving 10 mm gap for thermal expansion.

Coupler

Single tee with door

110 mm bend

Shoe (Plain)

110 mm Shoe

Providing and fixing PVC Floor Trap of approved quality for disposal of water of Wash Basin/Floor etc. including cutting of floors/walls & jointing with existing pipe line wherever required with all repair works for fixing the same etc. all complete as per direction of Engineer-in-charge.

100 mm inlet and 75 mm out let.

100 mm inlet and 100 mm out let

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Flexible pipe32 mm dia

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :

Oval shape 450x350 mm (outer dimensions)

Rectangular shape 1500x450 mm

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement: 4 coarse sand) and making good the wall etc. complete.110 mm

Hacking of CC flooring including cleaning for surface etc. complete as per direction of the Engineer-in-Charge.

Providing and fixing PTMT Bottle Trap for Wash basin and sink.Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with ittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :Range of three half stall urinals with 10 litre P.V.C. automatic flushing cistern

Providing and fixing toilet paper holder :C.P. brass

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre &post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in- Charge.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests(Hindware,parryware)

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc omplete.(parryware,hindware,jaquar)

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work)

15 mm nominal bore

20 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 20 mm nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

20 mm nominal outer dia Pipes

32 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge..Internal work - Exposed on wall 50 mm nominal outer dia Pipes

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink with drain board510x1040 mm bowl depth 200 mm

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shadeArea of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.Granite work

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm)of approved make and quality as per direction of Engineer-in-charge.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 800x800 mm

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 800x800 mm

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete.8mm thickGranite of any colour and shade

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :Of area 3 sq. metres and below

Taking out doors, windows and clerestory window shutters (steel orwood) including stacking within 50 metres lead :Of area 3 sq. metres and below

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Structural steel work in single section, fixed with or without connecting plate,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineerin- charge complete.205 X 19 mm

Providing and fixing bright finished brass casement window fasteners or peg stays to windows/ ventilators with necessary welding and machine screws etc. complete.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm)

Extra for providing frosted glass panes of all thick instead of ordinary float glass panes(as in item of glass panes) in doors, windows and clerestory window shutters/partitions .(Area of opening for glass panes excluding portion inside rebate shall be measured).

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :150x10 mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :125 mm

Providing and fixing urinal partition with pvc sheet of (12-18 )mm thick of size 900mm(height) x 500 mm(width) corner chamfered fixed in brick wall with stainless steel clips of grade 304 all complete.

P/F reflective sun control film (of make garware or equivalent) of 2 Mil thick. And total solar energy rejection above 70% in required colour at all heights, locations and floor i/c removal of old film from glass (wherever required) all complete as per direction of E- IN- CHARGE

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing white vitreous china wash basin of make (jaquar model No. FLS WHT 0401 orParryware Geneve Under Countertop Wash Basin) including making all connections, the cost of fittingswith C.I. brackets, 15 mm C.P. brass pillar taps(PRS-CHR-031 jaquar,F310001 pressmatic hindware), 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:: under counter wash basin of size 51x42x19.2 cm approx

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing CP Brass Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 31 mm dia .

Providing and fixing C.P. brass ,JAGUAR MAKE -SOLO BRAND ,(QUARTER TURN QUALITY ,SOL-6053, Hindware F280004) Angular Stop cock with wall flange complete as per direction of EinC and manufacturer specification .

Providing and fixing C.P. brass ,(JAGUAR MAKE -SOLO BRAND ,QUARTER TURN QUALITY ,SOL-6047, Parryware Lapis-N Push Tap T2024A1 Brass Bib Cock (Silver) ) Bib cock (Straight line Model)with wall flange complete as per direction of EinC and manufacturer specification .

Providing and fixing C.P. brass ,(JAGUAR MAKE -SOLO BRAND ,QUARTER TURN QUALITY ,SOL-6041, Parryware Sapphire Two Way Bibcock, G0334A1) Two way bib cock with wall flange complete as per direction of EinC and manufacturer specification .

Providing and fixing C.P. brass ,HOLE BIDET Mixer with pop up waste system with 300 mm longbrided hoses QUALITY ,(JAGUAR MAKE -SOLO BRANDSOL-6613B, Hindware Modern F400009) complete as per direction of EinC and manufacturer specification .

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing (JAGUAR MAKE ALD-803AB or equivalent) 450mm long braided hose with M10X1 nipple 15mm nut O ring and rubber washer complete as per direction of EinC and manufacturer specification .

Providing and fixing CP Brass towel rail (Make Jaguar model No. AKP-CHR-35711P or Paryware Model No. T6709A1))complete with brackets fixed to wooden/ PVC cleats with CP brass screws with concealed fittings arrangement of approved quality and colour 600 mm long all complete as per direction of engineer in Charge

Providing and fixing CP Brass double coat hook (Make Jaguar model No. AKP-CHR-35761P or Hindware model no. Robe Hook Cat. No. 87007) )complete with brackets fixed to wooden /PVC cleats with CP brass screws with concealed fittings arrangement of approved quality and colour all complete as per direction of engineer in Charge

Providing and fixing CP Brass liquid soap container with glass bottle (Make Jaguar model No. ACN-CHR-1135N or Paryware Model No. T6513A1) distance from wall of standard shape with bracket all complete as per direction of engineer in Charge

Providing and fixing Hand Shower ( Health FAUCET)(JAGUAR MAKE -ALD-CHR 573,Parryware Multi Flow Hand Shower, T9983A1,Hindware Cascade Chrome Brass 5 Flow Hand Shower, F160007) with 8 mm dia , minimum 1.00 meter long with Nuts and washers Flexible tube with wall hook complete as per direction of EinC and manufacturer specification

Providing and Fixing custom made electric motorised control system with centralized remote Roller blinds of shade and type and of approved make comprising of roller tube, clutch, idler, installation brackets and bottom weight controlling motor and remove control. Roller tube shall be of anodized extruded Aluminium section of min. 1.0mm thickness and 32mm O.D. Clutch shall be of wrap spring design with high strength fibreglass reinforced polyester assembly. Clutch mechanism shall be crash proof, prevent slippage and shall raise and lower smoothly to any desired height all complete as per direction of engineer in charge.

Providing and Fixing Custom made Roller blinds of required shade and type and of approved make comprising of roller tube, clutch, idler, installation brackets and bottom weight. Roller tube shall be of anodized extruded Aluminium section of min. 1.0mm thickness and 32mm O.D. Clutch shall be of wrap spring design with high strength fibreglass reinforced polyester assembly. Clutch mechanism shall be crash proof, prevent slippage and shall raise and lower smoothly to any desired height all complete as per direction of engineer in charge.

Removing existing damaged tarfelt/bitumen laid over roof with grading mortor in two layes ( total thickness approximaterly 15mm) i/c cost of removing all residual of bitumen and attached mortor grading (upto 15mm total thickness) and dumping the waste material at Ground floor within 50 meter lead ,complete as per direction of EinC(extra shall be paid above 15mm thickness in demolishing CC item No 2)..

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.(A)Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

15 mm cement plaster on the rough side of single or half brick wall of mix(A)1:4 (1 cement: 4 fine sand

15 mm cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement on the rough side of single or half brick wall.

Grading roof for water proofing treatment with

Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size

Cement mortar 1:4 (1cement : 4 coarse sand)

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting ofapplying: a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/ sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hoursfollowed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around.d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treatedsurface will be measured. (water proofing compound/ liquid to be used shall be of manufacture such as Tapecrete/pedicrete/asianpaint etc make or as approved by EinC)

Crazy ceramic tile flooring, with under layer 12 mm thick cement mortar 1:4 (1 cement: 4 coarse sand), with joints not exceeding 5 mm, including filling the gaps with ordinary cement mixture & mixing with synthetic polyester fibre, triangular in shape having specific gravity of1.34 to 1.40, cross section size ranging from 10 to 40 micron & length upto 6 mm , mixing fibre @ 125 grams per 50 kg of cement in cement mortar, including providing and mixing water proofing material in mortar@ 1 kg per 50 kg of cement , all complete as per direction of Engineer-in-charge.

Disposal of building rubbish /lime ,moorum/ similar unserviceable, dismantled or waste materials by mechanical means including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, upto 25 km lead including all lifts involve

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.Two coats

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One or more coats on old work

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :New work (two or more coats) over and including water thinnable priming coat with cement primer

Deduct one coat of water thinnable cement primer of approved brand and manufacture on wall surface :Water thinnable cement primer

Distempering with 1st quality acrylic distember (Ready mix) having VOC content less than 50 grams/ litre of approved brand and manufacture to give an even shade :Old work (one or more coats)

Cleaning of sewerline with roding & taking out the silt/sludge etc. to make the sewerline operational including disposal of malba with in 100 meter lead as directed by Engineer-in-Charge. upto 450mm dia pipe and MH to MH distance 30 meter.

Cleaning of manhole manually including taking out silt/sludge & disposing the same with in 100 meter lead as directed by Engineer-in-Charge.

a)90cmx80cm

b) 120cmx90cm

Credit to work:(Only for unusable scrap items)

i)Wooden doors shutter (Flush Door shutter / panelled door shutter/ PVC door shutter)

ii)Reinforcement bars / M.S.Section/old G.I. Pipe

iii)Aluminium sliding door bolt of any size

iv)Aluminium Tower bolt of any size

v)alum member

vi)Brick work

vii)Plastic Bib Cock/ /Stop Cock / Pillar Cock

viii)PVC Cistern of any size with available accessories

ix)Misc. CI/SCI materials

x)Floor spring with its available accessories

xi)Hydraulic Door closer

xii)PVC Partition of any size and brand

xiii)15-20 mm thick granite stone

M/s Raghav Engineers

BPT Infra Projects Pvt. Ltd.

MODERN CONCEPT CONSTRUCTIONS