Construction of Cultural Heritage Centre at Village Thalwal, Jammu, UT of J and K

BILL OF QUANTITY

Sl. No. DESCRIPTION UNIT Qty RATE Amount (in Rs)

A 2.0 EARTH WORKS

Earth work in excavation by mechanical means (Hydraulic

excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m

1 2.7 in width as well as 10 sqm on plan) including getting out and disposal of

excavated earth lead upto 50 m and lift upto 1.5 m, as directed by

Engineer-in-charge.

Extra for every additional lift of 1.5 m or part thereof in

excavation/banking excavated or stacked material :

Excavating trenches of required width for pipes, cables, etc including

excavation for sockets, and dressing of sides, ramming of bottoms, depth

upto 1.5 m, including getting out the excavated soil, and then returning

5 2.9 the soil as required, in layers not exceeding 20 cm in depth, including

consolidating each deposited layer by ramming, watering, etc. and

disposing of surplus excavated soil as directed, within a lead of 50 m :

Filling available excavated earth (excluding rock) in trenches, plinth,

sides of foundations etc. in layers not exceeding 20cm in depth,

consolidating each deposited layer by ramming and watering, lead up to

50 m and lift upto 1.5 m.

Excavating, supplying and filling of local earth (including royalty) by

mechanical transport upto a lead of 5km also including ramming and

watering of the earth in layers not exceeding 20 cm in trenches, plinth,

sides of foundation etc. complete.

Surface dressing of the ground including removing vegetation and

9 2.12 inequalities not exceeding 15 cm deep and disposal of rubbish, lead up 100 Sqm 5.00 2412.00 12060.00

to 50 m and lift up to 1.5 m. All kinds of soil

Disposal of excavated excess earth away from the site including

conveyance of materials up to an average lead of 5KM away from the

site, and correspondiong required lift, loading, unloading etc complete as

directed by the Engineer-in-charge. (The quantity is net quantity of

capacity of truck after deduction of 20% for looseness)(considering the

maximum disposal location at 5 KM distance)

By mechanical transport including loading, unloading and stacking. (Lead

upto 5KM away from the site)

Supplying and filling in plinth with fine sand under floors including,

watering, ramming, consolidating and dressing complete.

Supplying chemical emulsion in sealed containers including delivery as

specified. Chlorophriphos/Lindane emulsifiable concentrate of 20%

14 Anti termite treatment

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL

15 2.29 anti-termite treatment (excluding the cost of chemical emulsion) :

Along external wall where the apron is not provided using chemical

emulsion (Chlorophriphos/ Lindane E.C. 20% with 1% concentration) @

16 2.29.1 7.5 litres/sqm of the vertical surface of the sub-structure to a depth of Meter 121 28.95 3502.95

300 mm including excavation of channel along the wall & rodding etc.

Treatment of soil under existing floors using chemical emulsion @ one

litre per hole, 300 mm apart including drilling 12 mm diameter holes and

plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match

the existing floor:

18 4.0 CONCRETE WORKS

Providing and laying in position cement concrete of specified grade

19 4.4 excluding the cost of centering and shuttering - All work up to plinth level

1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm

Centering and shuttering including strutting, propping etc. and removal of

form work for :

22 4.6.1 Foundations, footings, bases for columns. Sqm 116.00 286.35 33216.60

Providing and laying damp-proof Course 50 mm thick with cement

23 4.18 concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone aggregate 20 Sqm 28.00 416.50 11662.00

mm nominal size) and curing complete

Sl. No. DESCRIPTION UNIT Qty RATE Amount (in Rs)

Providing and mixing water proofing material in cement concrete work in

24 4.19 doses by weight of cement as per manufacturer’s specification. (1 kg of Kg 9.00 63.00 567.00

water proofing material in 50 kg of cement)

Providing & applying a coat of residual petroleum bitumen of grade of VG-

10 of approved quality using 1.7kg per square metre on damp proof

course after cleaning the surface with brushes and finally with a piece of

cloth lightly soaked in kerosene oil.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement

: 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal

size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well

rammed and consolidated and grouted with fine sand, including

necessary excavation, levelling & dressing & finishing the top smooth.

27 5.0 REINFORCED CEMENT CONCRETE WORK

Centering and shuttering including strutting, propping etc. and removal of

29 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete. Sqm 122.00 286.35 34934.70

Walls (any thickness) including attached pilasters, butteresses, plinth

and string courses etc.

31 5.9.3 Suspended floors, roofs, landings, balconies and access platform. Sqm 235.00 718.20 168777.00

32 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers Sqm 483.00 577.55 278956.65

33 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts. Sqm 395.00 742.55 293307.25

Extra for shuttering in circular work (20% of respective centering and

Shuttering items)

Steel reinforcement for R.C.C. work including straightening, cutting,

bending, placing in position and binding all complete upto plinth level.

37 5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. Kg 14816.00 123.20 1825331.20

Steel reinforcement for R.C.C. work including straightening, cutting,

bending, placing in position and binding all complete above plinth level.

39 5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. Kg 16156.00 123.20 1990419.20

Providing and laying in position machine batched and machine mixed

design mix M-25 grade cement concrete for reinforced cement concrete

work, using cement content as per approved design mix, including

pumping of concrete to site of laying but excluding the cost of centering,

shuttering, finishing and reinforcement, including admixtures in

recommended proportions as per IS: 9103 to accelerate, retard setting of

concrete, improve orkability without impairing strength and durability as

per direction of Engineer-in charge. Note: - Cement in this item is @ 330

kg/ cum. Excess or less cement used as per design mix is content

considered payable or recoverable separately.

41 5.34.1 All works upto plinth level. Cum 154.00 8021.10 1235249.40

42 5.34.2 All works above plinth level upto floor V level. Cum 115.00 9412.05 1082385.75

Add or deduct for using more or less cement in the items of design mix

over and above the specified cement content therein.

Providing and placing in position 100-200mm thick factory made

machine batched and machine mixed Precast RCC Rectangular Covers

on drains of footpath of various sizes, of M-25 grade cement concrete for

RCC work, including cost of centering, shuttering, reinforcement of 8mm

dia TMT bars of Fe 500 grade @ maximum 100mm c/c on both ways ,

44 16.96 neat cement punning on finished surface, properly encased on all edges Sqm 225.00 3681.60 828360.00

with 1.6 mm thick , 100mm wide MS sheet duly painted over priming coat

, reinforcement to be welded at edges with MS sheet and providing 2

Nos. 12 mm dia bar for hooks etc i/c cost of cartage ,all leads & lift,

handling at site etc. all complete as per direction of Engineer-in-Charge.

Providing and fixing in position precast R.C.C. manhole cover and frame

45 20.15.1.1 of required shape and approved quality. LD - 2.5. Rectangular shape each 4.00 1312.35 5249.40

600x450 internal dimensions.

46 6.0 BRICK WORK

Brick work with common burnt clay F.P.S. (non modular) bricks of class

designation 7.5 in foundation and plinth in:

48 6.1.5 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 28.00 7571.55 212003.40

Brick work with non modular fly ash bricks conforming to IS:12894, class

49 6.38 designation 10 average compressive strength in super structure above

plinth level up to floor V level in :

50 6.38.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 27.00 6885.90 185919.30

Half brick masonry with non modular fly ash bricks of class designation

10, conforming to IS: 12894, in superstructure above plinth level and upto

floor V level and curing complete in:

Sl. No. DESCRIPTION UNIT Qty RATE Amount (in Rs)

52 6.45.2 Cement mortar 1:4 (1 cement : 4 coarse sand) Sqm 3 880.65 2641.95

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at

every third course of half brick masonry.

54 RANDOM RUBBLE MASONRY

Random Rubble masonry with hard stone in foundation and plinth

including leveling up with cement concrete 1:6:12 (1 Cement : 6 coarse

sand : 12 graded stone aggregate 20mm nominal size) upto plinth level

and curing complete with:

56 7.1.1A Quarry, Cement mortar 1:6 (1 Cement : 6 coarse sand) Cum 391.00 7677.35 3001843.85

Random Rubble masonry with hard stone in superstructure above plinth

level and upto floor five level, including levelling up with cement concrete

57 7.2 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 20mm

nominal size) and curing complete at window sills, ceiling level and the

58 7.2.1A Quarry, Cement mortar 1:6 (1 Cement : 6 coarse sand) Cum 664.00 9131.90 6063581.60

59 7.4 Extra for random rubble masonry with hard stone in:

60 7.4.1 Square or rectangular pillars Cum 664.00 769.35 510848.40

Extra for random rubble masonry with hard stone curved on plan for a

mean radius not exceeding 6 m.

62 8.0 MARBLE & GRANITE WORKS

Providing and fixing machine cut, mirror / egg shell polished , Marble

stone work for wall lining (veneer work) including dado, skirting, risers of

steps etc., in required design and pattern wherever required, stones of

different finished surface texture, on 12 mm (average) thick cement

mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement

63 8.11 slurry @ 3.3 kg/sqm including pointing with white cement slurry admixed Sqm 25.00 9580.45 239511.25

with pigment of matching shade, including rubbing, curing, polishing etc.

All complete as per Architectural drawings, and as directed by the

Engineer- in-Charge. a. 18 mm thick Italian Marble stone slab, Perlato,

Rosso Verona, Fire Red or Dark Emperadore etc.

Providing and fixing machine cut, mirror / eggshell polished , Granite

stone work for wall lining (veneer work) including dado, skirting, risers of

steps etc., in required design and pattern wherever required, stones of

different finished surface texture, on 12 mm (average) thick cement

mortar 1:3 (1 cement : 3 oarse sand) laid and jointed with white cement

64 MR-09 slurry @ 3.3 kg/Sq.Mt. including pointing with white cement slurry Sqm 111.00 7148.20 793450.20

admixed with pigment of matching shade, including rubbing, curing,

polishing etc. all complete as per Architectural drawings, and as directed

by the Engineer-in-Charge. a. 18 mm thick Granite stone slab any colour

Stone Cladding - Providing & fixing Stone work for wall lining and column

cladding backing filled with a grout of 20mm thick

cement mortar 1:3 (1 cement 3 coarsesand) including pointing in grey

cement mortar 1:2 (1 cement : 2 stone dust) with an admixture of

pigment matching the stone shade all complete as per design and

direction of Architect. Including stone, cement, sand, material, labour,

Scaffolding, transport & taxes etc complete. Basalt Stone - Exposed face

chisel dressed and rough backing - 80 mm thick

Providing and fixing cramps of required size and shape for anchoring

stone wall lining to the backing or securing adjacent stones in stone wall

lining in cement mortar 1:2 (1 cement: 2 coarse sand) including making

the necessary chases in stone and holes in walls wherever required.

67 8.14.2 Stainless Steel Cramp kg 538.00 677.10 364279.80

Providing and fixing adjustable stainless steel cramps of approved quality

and of required shape and size adjustable with stainless steel nuts, bolts

and washers (total weight not less than 260gms) for dry stone cladding

68 8.15 fixed on frame work at suitable location including making necessary each 538.00 357.20 192173.60

recesses in stone slab, drilling required holes etc. complete as per the

direction of engineer-in-charge.

Providing and fixing copper pins 7.5 cm long 6 mm diameter for securing

adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2

69 8.16 coarse sand) including making the necessary chases. each 538.00 47.75 25689.50

70 9.0 WOOD & PVC WORK

Sl. No. DESCRIPTION UNIT Qty RATE Amount (in Rs)

Providing and fixing 35-40 mm thick, solid panel, carved Teak Wood

door shutter, of approved design, including necessary frame made of

seasoned wood (size to be specified, e.g., 100x60mm), all complete as

per drawing and specifications. The rate includes:

* Approved quality teak/hardwood seasoned to below 16% moisture

content and chemical treated for termite resistance.

* Intricate 3D CNC or hand carving design, with a brown finish and

71 MR-2 premium melamine/Italian polish (e.g., 3 coats). Sqm 16.00 17500.00 280000.00

* All necessary hardware, including hinges (e.g., 4" long SS hinges),

handles, Godrej/Doorset lock (6-lever cylindrical lock), tower bolts, door

stoppers, screws, etc., of approved make.

* All labour charges, materials, transportation, tools and tackles, and

incidental costs to complete the work in all respects as directed by the

Engineer-in-Charge.

72 10.0 STEEL WORK

Steel work in built up tubular (round, square or rectangular hollow tubes

etc.) trusses etc., including cutting , hoisting , fixing in position and

applying a priming coat of approved steel primer, including welding and

bolted with special shaped washers etc. complete.

74 10.16.1 Hot finished welded type tubes kg 8577.00 156.95 1346160.15

Steel work welded in built up sections/ framed work including cutting,

75 10.25 hoisting, fixing in position and applying a priming coat of approved steel

primer using structural steel etc. as required

In stringers, treads, landings etc. of stair cases, including use of

76 10.25.1 chequered plate wherever required, all complete. kg 125.00 141.40 17675.00

In gratings, frames, guard bar, ladder, railings, brackets, gates and

Providing and fixing carbon steel galvanised ( minimum coating 5

micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield

78 10.27 strength 480 N/mm2), counter sunk head, comprising of 10 m dia

polyamide PA 6 grade sleeve, including drilling of hole in frame ,

concrete/ masonry, etc. as per direction of Engineer-in-charge.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow

tubes, channels, plates etc., including welding, grinding, buffing,

polishing and making curvature (wherever required) and fitting the same

with necessary stainless steel nuts and bolts complete, i/c fixing the

railing with necessary accessories & stainless steel dash fasteners ,

stainless steel bolts etc., of required size, on the top of the floor or the

side of waist slab with suitable arrangement as per approval of Engineer-

in-charge, (for payment purpose only weight of stainless steel members

shall be considered excluding fixing accessories such as nuts, bolts,

fasteners etc.)

81 11.0 FLOORING WORK

82 11.34 Extra for pre finished nosing to treads of steps of marble stone Meter 99.00 553.70 54816.30

Extra for marble stone flooring in treads of steps and risers using single

length up to 2.00 meter.

Providing and laying Polished/Flamed natural stone flooring (e.g.,

Granite, Sandstone) in required design and patterns, with 18mm

(approx.) thick stone slab over 20mm (average) thick base of cement

84 MR-3 mortar 1:4 (1 cement: 4 coarse sand), laid and jointed with grey cement Sqm 464.00 3600.00 1670400.00

slurry @ 3.3 kg/sqm, including pointing in white cement mixed with

pigment of matching shade, rubbing, curing, and polishing etc., complete

Providing and laying machine cut, mirror polished Marble stone flooring,

in required design (Simple geometrical, abstract etc.) and in patterns in

combination with Italian marble stones of different colours, shades and

finished surface texture etc., in linear portions of the building, all

complete as per the architectural drawings, with 18 mm thick stone slab

laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement: 4

85 11.64 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm

including pointing with white cement slurry admixed with pigment to

match the marble shade including rubbing, curing and polishing etc. all

complete as specified and as directed by the Engineerin- Charge.

a. 18 mm thick Italian Marble stone slab, Perlato, Rossoverona, Fire Red

or Dark Emperadore etc.

Sl. No. DESCRIPTION UNIT Qty RATE Amount (in Rs)

Providing and fixing Glass mossaic tiles at finished plain wall surface of

size 20 mm x 20 mm x 4 mm in all colour, design, fixing in customize

design as per direction of Engineer-in- Charge. The glass mosaic tiles to

be fixed on the wall surface with the help of approved adhesive applied at

87 11.65 the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive Sqm 297.00 3393.95 1008003.15

of all operation, material and required pattern approved by Engineer-in-

Providing and laying Polished Granite stone flooring in required design

and patterns, in linear as well as curvilinear portions of the building all

complete as per the architectural drawings with 18 mm thick stone slab

over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4

88 11.68 coarse sand) laid and jointed with cement slurry and pointing with white

cement slurry admixed with pigment of matching shade including

rubbing, curing and polishing etc. all complete as specified and as

directed by the Engineer-in-Charge.

Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye

90 12.0 ROOFING

Providing and fixing precoated galvanized iron profile sheets (size, shape

and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+

0.05 %) total coated thickness with zinc coating 120 grams per sqm as

per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both

side of the sheet and polyester top coat 15-18 microns. Sheet should

have protective guard film of 25 microns minimum to avoid scratches

91 12.23 during transportation and should be supplied in single length upto 12 Sqm 133.00 706.50 93964.50

metre or as desired by Engineer-in-charge. The sheet shall be fixed

using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM

seal, complete upto any pitch in horizontal/ vertical or curved surfaces,

excluding the cost of purlins, rafters and trusses and including cutting to

size and shape wherever required.

92 ACCESSORIES

Providing and fixing precoated galvanised steel sheet roofing

accessories0.50 mm (+0.05 %) total coated thickness, Zinc coating 120

93 12.24 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns

epoxy primer on both side of the sheet and polyester top coat 15-18

microns using self drilling/ self tapping screws complete :

95 12.24.6 Gutter .(600 mm over all girth metre 24.00 1174.10 28178.40

Supplying and fixing approved quality wooden shingles (e.g., cedar, pine)

of specified thickness (e.g., 20mm) and size, laid in courses with required

96 MR-4 overlap and exposure to weather, fixed with stainless steel Sqm 277.00 3767.40 1043569.80

nails/fasteners to battens/sheathing, including all cutting and wastage.

97 13.0 FINISHING WORK

98 13.4 12 mm cement plaster of mix :

18 mm cement plaster in two coats under layer 12 mm thick cement

plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement

plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge.

6 mm cement plaster of mix :6 mm cement plaster to ceiling of mix 1 : 3

(1 cement : 3 fine sand)

Extra for providing and mixing water proofing material in cement plaster

work in proportion recommended by the manufacturers.

Providing and applying plaster of paris putty of 2 mm thickness over

plastered surface to prepare the surface even and smooth complete.

Distempering with 1st quality acrylic distemper (ready mixed) having

VOC content less than 50 gms/litre, of approved manufacturer, of

required shade and colour complete, as per manufacturer's specification.

Two or more coats on new work.

Wall painting with premium acrylic emulsion paint of interior grade,

having VOC (Volatile Organic Compound ) content less than 50 grams/

105 13.90.2 litre of approved brand and manufacture, including applying additional Sqm 384.00 109.90 42201.60

coats wherever required to achieve even shade and colour. Two coats.

Applying priming coats with primer of approved brand and

manufacture, having low VOC (Volatile Organic Compound ) content.

106 13.93.3 With water thinnable cement primer on wall surface having VOC content Sqm 384.00 64.15 24633.60

less than 50 grams/litre

Sl. No. DESCRIPTION UNIT Qty RATE Amount (in Rs)

Finishing walls with textured exterior paint of required shade on New

107 13.54 work (two or more coats applied @ 3.28 liter/10sqm) over and including Sqm 456.00 268.45 122413.20

base coat of exterior primer applied @ 2.20kg/10sqm

Painting with synthetic enamel paint of approved brand and manufacture

to give an even shade :

109 13.70.1 Two or more coats on new work Sqm 163.00 131.85 21491.55

Floor polishing on masonry or concrete floors with wax polish of

110 13.78 approved brand and manufacture Sqm 792.00 76.50 60588.00

Providing and applying white cement based putty of average thickness 1

111 13.88.1 mm, of approved brand and manufacturer, over the plastered wall Sqm 840.00 138.10 116004.00

surface to prepare the surface even and smooth complete

Add for plaster drip course/ groove in plastered surface or moulding to

R.C.C. projections.

Providing and Fixing of GRC Jali (Glass Fibre Reinforced Jali) 50 mm

thick of required size, pattern, design, and colour with 50% area covered

to be fixed on/between RCC / Block work Column or structural steel work

with Dry Fixing method. Fixing of (Glass Fibre Reinforced Jali) GRC Jali

to be fixed on/between RCC / Block work Column or structural steel work

113 MR-5 with Dry Fixing method with appropriate steel frame work , using Sqm 195.00 5736.65 1118646.75

fasteners, and necessary hardware etc in Building Facade. The jali shall

be securely fixed with stainless steel bolts and anchor fastners(304

grade) of required size at specified locations. The fixing shall be done by

the specialized approved agency as directed by Engineer-in-Charge.

Raking out joints of stone masonry surface to the required width and

depth, with due care and precaution by mechanical/manual means

114 29.1 including preparing and cleaning the surface for re-pointing / refilling of Sqm 150 51.45 7717.50

joints, including disposal of rubbish to the dumping ground within 50 mtrs

Cleaning the sand stone surface and removing dirt, dust, bird dropping,

grease, oil, algae, fungue, monkey beats, vegetable growth etc. including

providing, applying and washing the surface with liquid ammonia

chemical of 5% solution and other chemical cleaning agents as approved

by Archaeological survey of India/Engineer-in-charge, of approved brand

and manufacturer with the help of required scrubbers and also cleaning

115 29.3 with machine operated water jet mixed with desired quantity of fine silica Sqm 457 163.80 74856.60

and finally washing the surface with clean water with the help of pressure

jet machine, windows door etc, by suitable covering so as to avoid any

damage to the building/structure, all as per directions of Engineer-in-

charge(the rate is inclusive of all materials and labours involved except

Applying two or more coats of Ethyl silicate chemicals as approved by

Archaeological survey of India/ Engineer-in-charge, of approved brand

and manufacturer, with brush or spray on the existing stone masonry

surface till there is no further absorption of chemical by stone surface,

including protecting the applied surface from direct sun light by suitable

means during application, all complete as per direction of the Engineerin-

charge ( the rate is inclusive of all materials and labours involved except

Providing and fixing of 12mm Flexiply Plywood Board overArtwork- in

6mm white acrylic sheet with CNC Cutting design as per drawing to be

fixed walls from M.S frame work including cutouts for light fittings . The

entire work to be executed as per the drawings / instructions of the

117 MR-6 Engineer-in-charge including all the required approved material, labour Sqm 93 9500.00 883500.00

and fixing as per drawings enclosed. The work shall be executed as per

specification , & instructions of engineer in charge.

Providing and Fixing brass Kalash varies widely, for large temple

shikharams (dome-top kalashes), depending heavily on size, weight, and

118 MR-7 intricate design including all the required approved material, labour and Kg 500.00 850.00 425000.00

fixing as per drawings enclosed.

119 15.0 DISMANTLING AND DEMOLISHING

Sl. No. DESCRIPTION UNIT Qty RATE Amount (in Rs)

Demolishing cement concrete manually/by mechanical means including

120 15.2 disposal of material within 50 meters lead as per direction of Engineer-

121 15.2.2 1:4:8 or leaner mix (i/c equivalent design mix) Cum 6.00 1064.55 6387.30

Demolishing R.C.C. work manually/by mechanical means including

stacking of steel bars and disposal of unserviceable material within 50

122 15.3 meters lead as per direction of Engineer-in-charge. Cum 40.00 2516.85 100674.00

Demolishing brick work manually/by mechanical means including

stacking of serviceable material and disposal of unserviceable material

123 15.7 within 50 meters lead as per direction of Engineer-in-charge:

Demolishing stone rubble masonry manually/by mechanical means

including stacking of serviceable material and disposal of unserviceable

125 15.9 material within 50 meters lead as per direction of Engineer-in-charge:

Dismantling steel work in built up sections in angles, tees, flats and

channels including all gusset plates, bolts, nuts, cutting rivets, welding

127 15.18 etc. including dismembering and stacking within 50 meters lead. Kg 350 4.30 1505.00

Dismantling stone slab flooring laid in cement mortar including stacking

of serviceable material and disposal of unserviceable material within 50

Dismantling concrete grouted stone pitching in aprons drains etc.

including stacking of serviceable material and disposal of unserviceable

129 15.59 material, stacking /disposal lead upto 100 meters. Cum 15.00 1535.90 23038.50

130 15.61 Demolishing RCC work by mechanical means & stockpiling at Cum 124.00 2048.70 254038.80

131 16.0 designated

ROAD WORK locations & disposal of dismantled materials upto a lead of 1

Preparation of subgrade by excavating earth to an average of 22.5 cm

depth, dressing to camber and consolidation with road roller of 8-12

tonne capacity including making good the undulation etc. and disposal of

surplus earth upto 50 meters.

Supplying and Stacking of Good Earth by mechanical transport including

133 16.4.5 loading, unloading including royalty & carriage up to 5 KM complete. Cum 900.00 281.30 253170.00

Extra for compaction of earth work in embankment under optimum

135 16.3 moisture conditions to give at least 95% of the maximum dry density Cum 450.00 18.50 8325.00

(proctor density)

Spreading of sludge, dump manure or/and good earth in required

136 17.8 thickness as per directions of officer in-charge (cost of sludge, dump Cum 450.00 53.55 24097.50

manure or/and good earth to be paid separately)

Dry stone pitching 22.5 cm thick including supply of stones and preparing

surface complete.

Construction of granular sub-base by providing close graded Material

conforming to specifications, mixing in a mechanical mix plant at OMC,

carriage of mixed material by tippers to work site, for all leads & lifts,

138 16.82 spreading in uniform layers of specified thickness with motor grader on

prepared surface and compacting with vibratory power roller to achieve

the desired density, complete as per specifications and directions of

Engineerin- Charge.

With material conforming to Grade-II (size range 53 mm to 0.075 mm )

having CBR Value-25

Providing, laying, spreading and compacting graded stone aggregate

(size range 53 mm to 0.075 mm ) to wet mix macadam (WMM)

specification including premixing the material with water at OMC in for all

leads & lifts, laying in uniform layers with mechanical paverfinisher in sub-

base / base course on well prepared surface and compacting with

vibratory roller of 8 to 10 tonne capacity to achievethe desired density,

complete as per specifications and directions of Engineer-in-Charge.

Sl. No. DESCRIPTION UNIT Qty RATE Amount (in Rs)

Surface dressing one coat on new surface with bitumen of specified

grade at a rate of 1.95kg/sqm of surface area with 1.5 cum. of stone

141 16.36 chippings 13.2 mm nominal size per 100 sqm of road surface including

consolidation with road roller of 6 to 8 tonne capacity etc. complete.

Using bitumen emulsion ( minimum 50% bitumen content -RS grade

conforming to IS: 8887)

Providing and applying tack coat using hot straight run bitumen of grade

VG - 10, including heating the bitumen, spraying the bitumen with

mechanically operated spray unit fitted on bitumen boiler, cleaning and

preparing the existing road surface as per specifications :

144 16.38.2 On bituminous surface @ 0.50 Kg / sqm Sqm 250 55.20 13800.00

Providing and laying Dense Graded Bituminous Macadam using crushed

stone aggregates of specified grading, premixed with bituminous binder

and filler, transporting the hot mix to work site by tippers, laying with

paver finisher equiped with electronic sensor to the required grade, level

145 16.62 and alignment and rolling with smooth wheeled, vibratory and tandem

rollers as per specifications to achieve the desired compaction and

density, complete as per specificatons and directions of Engineer-in-

50 to 100 mm average compacted thickness with bitumen of grade VG-

30 @ 5% (percentage by weight of total mix) and lime filler @ 2%

146 16.62.1 (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Cum 16.00 11968.50 191496.00

Plant of 100-120 TPH capacity.

Providing and laying bitumen mastic wearing course (as per

specifications) with industrial bitumen of grade 85/25 conforming to IS :

702, prepared by using mastic cooker and laid to required level and

slope, including providing antiskid surface with bitumen precoated fine

grained hard stone chipping of approved size at the rate of 0.005 cum

147 16.45 per 10 sqm and at approximate spacing of 10 cm centre to centre in both

directions, pressed into surface protruding 1 mm to 4 mm over mastic

surface, including cleaning the surface, removal of debris etc. all

complete. (Considering bitumen using 10.2% as per MORTH

specification).

Painting runway/taxi track/apron marking with adequate nos of coats to

give uniform finish with road marking paint of superior make as approved

149 16.55.1 by the Engineer-in-charge, i/c cleaning the surface of ail dirt, scales, oil, Sqm 162 165.25 26770.50

grease and other foreign material etc. and lining out complete. New work

(Two or more coats)

Providing and laying at or near ground level factory made kerb stone of M-

25 grade cement concrete in position to the required line, level and

curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand),

including making joints with or without grooves (thickness of joints except

150 16.75 at sharp curve shall not to more than 5mm), including making drainage Cum 2 8563.50 17127.00

opening wherever required complete etc. as per direction of Engineer-in-

charge (length of finished kerb edging shall be measured for payment).

(Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Providing and laying 500x500x40 mm thick Turf paver (Turfpave XD) on

150 mm thick sub grade of compacted bed of 20 mm thick nominal size

151 11.61 stone aggregate and base course and filling with 150 mm thick jamuna Sqm 50.00 1295.25 64762.50

sand, including spreading, well ramming, consolidating and finishing

smooth etc. all complete as per direction of Engineer-in-charge.

Construction of dry lean cement concrete sub base over a prepared sub-

grade with coarse and fine aggregate conforming to IS:383, the size of

coarse aggregate not exceeding 25 mm, aggregate cement ratio not to

exceed 15:1, aggregate gradation after blending to be as per

specifications, cement content not to be less than 150 Kg/cum, optimum

152 16.84 moisture content to be determined during trial length construction, Cum 160 3229.80 516768.00

concrete strength not to be less than 10 Mpa at 7 days, mixed in a

batching plant, transported to site, for all leads & lifts, laid with a

mechanical paver, compacting with 8-10 tonne vibratory roller, finishing

and curing etc. complete as per direction of Engineerin- charge.

Sl. No. DESCRIPTION UNIT Qty RATE Amount (in Rs)

Providing and laying factory made chamfered edge Cement Concrete

paver blocks in footpath, parks, lawns, drive ways or light traffic parking

etc, of required strength, thickness & size/ shape, made by table

vibratory method using PU mould, laid in required colour & pattern over

50mm thick compacted bed of sand, compacting and proper

embedding/laying of inter locking paver blocks into the sand bedding

layer through vibratory compaction by using plate vibrator, filling the joints

with sand and cutting of paver blocks as per required size and pattern,

finishing and sweeping extra sand. complete all as per direction of

Engineer-in-Charge.

60mm thick cement concrete paver block of M-35 grade with approved

colour, design & pattern.

Providing and fixing 10x10x7.50 cm Granite stone block hand cut and

chisel dressed on top, for paving in floors, drains etc. laid over 20mm

155 16.95 thick base mortar 1:4 (1cement:4 coarse sand) with joints 10mm wide Sqm 50.00 1814.15 90707.50

filled with same mortar including ruled pointing etc. complete as per

direction of engineer-in charge.

Providing and laying non-pressure of specified class R.C.C. pipes

including collars/spigot jointed with stiff mixture of cement mortar in the

proportion of 1:2 (1 cement: 2 fine sand) including testing of joints etc.

Non-pressure NP-4 class (Heavy duty) R.C.C. pipes, 450 mm dia. R.C.C.

158 17.00 HORTICULTURE AND LAND SCAPING

Supplying and stacking at site dump manure from approved source

including carriage complete (manure measured in stacks will be reduced

by 8% for payment)

160 17.4.2 Screened through sieve of I.S. designation 16 mm Cum 450 105.30 47385.00

161 17.4.3 Screened through sieve of I.S. designation 4.75 mm Cum 225 134.90 30352.50

162 17.7 Fine dressing of the ground. 100 Sqm 11 374.40 4118.40

Mixing earth and sludge or manure in the required proportion specified or

directed by the Officer-in-charge

Grassing with selection no. 1 grass including watering & maintenance of

the lawn for 30 days or more till the grass forms a thick lawn free from

164 17.10 weeds & fit for mowing including supplying of good earth if needed (the

good earth shall be paid separately.)

Digging holes in ordinary soil and refilling the same with the excavated

earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts

of stacked volume of earth after reduction by 20% : 1 part of stacked

166 17.14 volume of manure after reduction by 8%) flooding with water, dressing

including removal of rubbish and surplus earth, if any, with all leads and

lifts (cost of manure, sludge or extra good earth if needed to be paid for

168 17.14.2 Holes 90 cm dia, and 90 cm deep Each 75 394.80 29610.00

169 17.14.3 Holes 60 cm dia, and 60 cm deep Each 45 119.30 5368.50

170 17.14.4 Holes 45 cm dia, and 45 cm deep. Each 25 50.10 1252.50

Providing and fixing M. S. tree guard 45 cm square in plan, height 1.20

metre above ground level and 0.40 metre below ground level. The

vertical members shall consist of four nos. angle iron of size 25x25x3

mm, 1.6 m long, one at each corner and 8 nos flat iron of size 25x3 mm,

1.2 m long. The vertical members shall be welded to 4 nos. 25x6 mm M.

S. flats placed horizontally around the vertical member of the cage. One

name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be

171 17.26 welded to the tree guard near the middle height and lettered CPWD/ Each 195 3231.55 630152.25

PWD/ any other approved name. The tree guard shall be fixed to the

ground by making suitable holes and by embedding four corners leg in

the ground, including refilling the earth, compaction etc. complete. The

tree guard shall be painted with two or more coats of synthetic enamel

paint of approved brand and manufacture over a coat of primer, complete

in all respect.

Sl. No. DESCRIPTION UNIT Qty RATE Amount (in Rs)

Providing Circular Cement Concrete pots of specified size, cast with

cement concrete of nominal mix. 1:1.5:3 (1cement: 1.5 coarse sand:

3graded stone aggregate 6 mm nominal size) reinforced with 7 nos. ( 3

nos horizontal and 4 nos vertical ‘U” shape ) M.s wires of 3.5 mm dia as

172 17.29 per design, including required form work finishing with cement punning

on exposed surface curing for specified period and stacking in required

rows and height, all complete as per direction of officer-in-charge

Top inside dia 35 cm, outer bottom dia 25 cm, total height 35 cm with

173 17.29.1 wall thickness of 25.4 mm Each 150 280.25 42037.50

Providing Square Cement Concrete pots of specified size, cast with

cement concrete of nominal mix. 1:1.5:3 (1cement: 1.5 coarse sand: 3

graded stone aggregate 6 mm nominal size) reinforced with 7 nos. ( 3

nos horizontal and 4 nos vertical ‘U” shape ) M.s wires of 3.5 mm dia as

174 17.30 per design, including required form work finishing with cement punning

on exposed surface curing for specified period and stacking in required

rows and height, all complete as per direction of officer-in charge

Top inner width 35 cm, outer bottom width 25 cm, total height 35 cm and

176 Horticultur and Landscape DSR-2025

Providing & laying of Selection no. 1 Doob grass turf with earth 50mm to

60mm thickness of existing ground prepared with proper level and

ramming with required tools wooden and than rolling the surface with

light roller make the surface smoothen and light watering the same and

maintenance for 30 days or more till the grass establish properly, as per

direction of the officer-in-charge.

Complete maintenance of the entire garden features having as per yard

stick in the garden area i.e. lawn trees, shrubs, herbs, edge, flower beds,

foliages, creepers etc. including hoeing pruning replacement of plants,

gap filling, watering, mowing of lawn, grass cutting by lawn mover and

brush cutter, removal of garden waste, applying insecticide, pesticide &

fertilizers(whenever required), top dressing of lawn with good earth and

178 2.40 manure and maintenance of other garden related works as directed by

officer-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide,

Pesticide and plants will be provided by the department and lawn mover

and brush cutter with fuel & other T & P material/articles shall be

provided by the contractor).

179 2.40.5 Play grounds / Public parks (as per yard stick 1Mali =2.00Acre). 4500 3.10 13950.00

Complete maintenance of shrubs (outside garden features), jobs like

making of basin at regular interval including weeding, watering, prunning

and application of fertilizer etc, (excluding the cost of material which shall Per Plant/

180 2.43 be supplied by the department) and as per direction of officer in charge. Per Month 150 49.10 7365.00

(1 Mali for 500 Nos. Shrubs)

Providing & fixing White River (Stone) Pebbles size of 2" to 2.5" dia (5

cm to 6.25 cm), in natural colour at site of work including loading,

unloading, carriage etc. and as per direction of officer-in-charge.

Providing and applying anti termite treatment of infected trees i/c all

branches/leaves by spraying chemical emulsion 0.5% (Chlorpyriphos

182 2.55 20% EC) concentration, through power spray machine (@ 100 ml Each 195 84.60 16497.00

Chlorpyriphos per tree i/c cost of chemical) and as per direction of officer- Tree

Anti termite treatment of lawn area through Chloropyriphose 20% E.C., 5

liter diluted in 995 liters water and applying solution @ 1.00 litre solution

183 2.56 per sqm each application in lawn / bed area (two application) i/c cost of per Sqm 4500 4.10 18450.00

chemical) and as per direction of officer-in-charge.

Sl. No. DESCRIPTION UNIT Qty RATE Amount (in Rs)

184 4.0 Rose Plants

Providing, stacking and Displaying Budded Rose (H.T. variety) 3 to 4

healthy branch 30 cm and above ht. well developed with one and above

185 4.91 flower plant in 20 cm Earthen Pot/Plastic Pot as per direction of the Each 75 35.80 2685.00

officer-in-charge.

Providing, stacking and Displaying Creeper Rose variety 3 to 4 healthy

branch 60 cm and above ht. well developed with one and above flowers

186 4.92 in 25 cm Earthen Pot/Plastic Pot as per direction of the officer-incharge. Each 50 80.20 4010.00

Providing, stacking and Displaying of Standard Rose (H.T. variety) 3 to 4

healthy branch 90 cm and above ht. well developed with one and above

187 4.93 flowers in 25 cm Earthen Pot/Plastic Pot as per direction of the officer- in- Each 45 160.40 7218.00

Ornamental Plants

Providing, stacking and Displaying Bismarckia Palm 115 cm to 180 cm

ht. plant, well developed 12 and above good color fresh and healthy

189 5.11 leaves in 40 cm Cement Pot/ Plastic Pot and as per direction of the Each 50 2140.65 107032.50

officer-in- charge.

Providing, stacking and Displaying Bougainvillea named variety, Sobhra,

Thima, Marry palmar, Cherry Blossom etc. well developed with fresh &

190 5.12 healthy bushy plant in full bloom 75 cm to 90 cm ht. plant in 40 cm Each 35 475.00 16625.00

Cement Pot/ Plastic Pot and as per direction of the officer-in-charge.

Providing, stacking and Displaying Cycus revoluta in 35 cm challi,

specimen plant, having 30 to 40 with fresh and healthy, leaves having

191 5.14 25cmto30cmcircumfranceofbasestemwelldeveloped andasper direction Each 20 1295.50 25910.00

of the officer-in-charge.

Providing, stacking and Displaying Cyprus Golden Conical Shape 150

cm to 165 cm ht. plant, with fresh and healthy Golden colour foliage in

192 5.18 35cm Cement Pot/ Plastic Pot and as per direction of the officer-in- Each 25 1782.85 44571.25

Providing, stacking and Displaying Ficus Long Island Topiary well

developed with fresh & healthy 5 to 6 big ball specific size and shape 120

193 5.21 cm to 150 cm ht in 40 cm Cement Pot/ Plastic Pot and as per direction of Each 10 1295.50 12955.00

the officer-in-charge.

Providing, stacking and Displaying Foxtail palm well developed with fresh

& healthy foliage of ht. plant 210 cm to 240 cm in 40 cm Cement Pot/ 1295.50

Plastic Pot and as per direction of the officer-in-charge.

Providing, stacking and Displaying Golden Bottle brush Topiary well

developed with fresh & healthy foliage 5 to 6 big ball 115 cm to 180 cm ht

plant in 40 cm Cement Pot/ Plastic Pot and as per direction of the officer-

Providing, stacking and Displaying Latania Rubra Palm well developed

with fresh & healthy foliage 150 cm to 180 cm ht. plant with 6 to 7 leaves

in 35 cm Cement Pot/ Plastic Pot and as per direction of the officer-in-

Providing, stacking and Displaying Topiary plant of Ficus Bush King well

developed with fresh & healthy foliage from Top to Bottom with single

197 5.38 piller 60 cm to 75 cm spread, 210 cm to 225 cm ht. plant, in 35 cm Each 20 1357.20 27144.00

Cement Tray/Cement Pot/ Plastic Pot and as per direction of the officer-

198 6.0 Ground Covers Plants

Providing and stacking Clerodendrum inerme having ht. 25 cm to 30 cm

199 6.70 multi branched in 25 cm size of Earthen Pot / Plastic Pot and as per Each 35 24.05 841.75

direction of the officer-in-charge.

Providing and stacking Duranta Golden, having ht. 15 cm to 20 cm bushy

200 6.12 shape with fresh and healthy leaves in 15 cm size of Earthen Pot / Plastic Each 40 22.85 914.00

Pot and as per direction of the officer-in-charge.

Providing and stacking Iresine herbstii, of height 25 cm to 30 cm., full of

201 6.17 branches well developed in 15 cm size of Earthen Pot / Plastic Pot and Each 35 22.85 799.75

as per direction of the officer-in-charge.

Providing and stacking Wadelia trilobata,full of leaves in 15 cm size of

Earthen Pot / Plastic Pot and as per direction of the officer-in-charge.

203 7.0 Tree Plants

.Providing and stacking of Alstonia scholaris height 150-165 cm. in bag

size 25 cm as per direction of the officer-in-charge.

Sl. No. DESCRIPTION UNIT Qty RATE Amount (in Rs)

Providing and stacking of Azadirachta indica ( Neem ) height 120-130cm

in polybag size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Bottle palm ht. 270-300 cm bottom girth 40-50

206 7.12 cm well developed in big HDPE bag as per direction of the officer-in- Each 25 595.85 14896.25

Providing and stacking of Callistemon lanceolatus height 150-165 cm.

in poly bag size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Delonix regia (Gulmohar) height 150-165 cm.

in poly bag size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Ficus benjamina (green) height 150-165 cm.,

209 7.27 bushy with healthy branches and lush green foliage in big size HDPE bag Each 25 195.00 4875.00

as per direction of the officer-in-charge.

Providing and stacking of Ficus benghalensis (Banyan) height 120-135

cm. in poly bag size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Ficus nuda height 150-165 cm., bushy with

211 7.35 healthy branches and lush green foliage in big size HDPE bag as per Each 15 205.85 3087.75

direction of the officer-in-charge.

Providing and stacking of Ficus religiosa (Peepal) height 150-165 cm. in

poly bag size 30 cm as per direction of the officer-in-charge.

Providing and stacking of Nauclea cadamba (Kadam) height 150-165

cm. in poly bag size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Plumeria acutifolia height 150-165 cm. with 3-4

214 7.68 branches in big size HDPE bag as per direction of the officer-in- charge. Each 25 216.65 5416.25

Providing and stacking of Plumeria rubara height 120-150 cm., 3-4

215 7.72 branches and thick stem in big size HDPE bag as per direction of the Each 15 433.35 6500.25

officer-in-charge.

Providing and stacking of Polyalthia longifolia (Ashok) height 180-195

cm. in gunny bag size 30 cm as per direction of the officer-in-charge.

Providing and stacking of Eugenia jambolana (Jamun) height 150-165

cm. in poly bag size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Washingtonia filifera palm stem ht. 120-135 cm

218 7.90 with 8-10 healthy lush green leaves well developed in big size HDPE bag Each 30 704.20 21126.00

as per direction of the officer-in-charge.

219 8.0 SHRUBS

Providing and stacking of Euphorbia caracasana (bronze colour leaves)

220 8.16 of height 60-75 cm. with 2-3 branches in earthen pot of size 20 cm as per Each 45 43.35 1950.75

direction of the officer-in-charge.

Providing and stacking of Ficus blackii (F.vivion) (bushy) of height 150-

221 8.23 165 cm. with 8-10 branches and healthy foliage in earthen pot of size 30 Each 50 270.85 13542.50

cm as per direction of the officer-in-charge.

Providing and stacking of Hibiscus rosasinensis of height 90-105 cm.,

bushy in big size HDPE bag as per direction of the officer-in-charge.

Providing and stacking of Malpighia coccigera of height 30-45 cm.,

223 8.45 multibranched in earthen pot of size 20 cm as per direction of the officer- Each 30 54.15 1624.50

Providing and stacking of Nerium oleander (kaner) of height 60-75 cm.

224 8.50 with 5-6 branches in poly bag of size 25 cm as per direction of the officer- Each 25 43.35 1083.75

Providing and stacking of Putranjiva roxburghii of ht. 60-75 cm in bag of

size 20 cm as per direction of the officer-in-charge.

Providing and stacking of Thuja compacta of height 75-90 cm., conical

226 8.76 shaped, well formed with healthy foliage in earthen pot of size 30 cm as Each 25 140.85 3521.25

per direction of the officer-in-charge.

Supplying, erection and commissioning of DECOR INDIA GEYSER

FOUNTAIN in a pool of 5m dia. with 5nos. of Geyser jet, hydraulic circuit,

accessories and fittings, 15 nos. of 150 watt & 220 V submersible lamps

in aluminium casing powder coated body, gasket, light stand, light

changer, 3 phase 5 HP submersible pump set with necessary electrical

submersible cabling, conducting etc., electrical panel, MCB, starter, fuse,

227 MR-8 necessary internal wiring etc., outdoor electrical enclosure for the above Each 1 375000.00 375000.00

electrical panel, plumbing, fitting of valve etc.complete as specified and

directed. (Construction of Pool to be done as per the standard drawing

and to be measured and paid separately).

228 Sub-Total (Summary of Civil Works)-A 41746604.91

230 DSR-2025 SUBHEAD- I: DISTRIBUTION BOARD

Sl. No. DESCRIPTION UNIT Qty RATE Amount (in Rs)

Supplying and fixing following way, horizontal type three pole and neutral,

sheet steel, MCB distribution board, 415 V, on surface/ recess, complete

232 2.4 with tinned copper bus bar, neutral bus bar, earth bar, din bar,

interconnections, powder painted including earthing etc. as required. (But

without MCB/RCCB/ Isolator)

Supplying and fixing of following ways surface/ recess mounting, vertical

type, 415 V, TPN MCB distribution board of sheet steel, dust protected,

duly powder painted, inclusive of 200 A, tinned copper bus bar, common

234 2.5 neutral link, earth bar, din bar for mounting MCBs (but without MCBs and

incomer) as required.Make:BS,Havells,Legrand (Note : Vertical type

MCB TPDB is normally used where 3 phase outlets are required.)

Supplying and fixing following rating, double pole, 240 volts, isolator in

236 2.12 the existing MCB DB complete with connections, testing and

commissioning etc. as required.

Supplying and fixing following rating, four pole, 415 volts, isolator in the

238 2.13 existing MCB DB complete with connections, testing and commissioning

etc. as required.

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve,

miniature circuit breaker suitable for inductive load of following poles in

the existing MCB DB complete with connections, testing and

commissioning etc. as required.

Supplying and fixing following rating, double pole, single phase and

neutral, 240 volts, residual current circuit breaker ( RCCB), having a

sensitivity current upto 30 milliamperes in the existing MCB DB complete

with connections, testing and commissioning etc as required.

245 SUB-HEAD - II : INTERNAL WIRING

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5

sq.mm FRLS PVC insulated copper conductor

single core cable in surface / recessed steel conduit, with modular

switch, modular plate, suitable GI box and earthing the

point with 1.5 sq.mm FRLS PVC insulated copper conductor single core

cable etc. as required.

Wiring for group controlled (looped) light point/fan point/exhaust fan

point/ call bell point (without independent

switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor

single core cable in surface/ recessed steel conduit, and earthing the

point with 1.5 sq. mm FRLS PVC insulated copper conductor single core

cable etc. as required

Wiring for circuit/ submain wiring alongwith earth wire with the following

sizes of FRLS PVC insulated copper conductor, single core cable in

surface/ recessed steel conduit as required.

Supplying and fixing suitable size GI box with modular plate and cover in

front on surface or in recess, including providing and fixing 3 pin 5/6

amps modular socket outlet and 5/6 amps modular switch, connection

etc. as required. (For light plugs to be used in residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in

front on surface or in recess, including providing and fixing 6 pin 5/6 &

15/16 amps modular socket outlet and 15/16 amps modular switch,

connection etc. as required.

Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket

outlet, with 2 pole and earth, metal enclosed plug top along with 20 amps

260 2.18 "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, Each 5.00 1806.00 9030.00

with chained metal cover for the socket out let and complete with

connections, testing and commissioning etc. as required.

Sl. No. DESCRIPTION UNIT Qty RATE Amount (in Rs)

Supplying and fixing suitable size GI box with modular plate and cover in

front on surface or in recess, including providing and fixing 32 amps

modular socket outlet and 32 amps modular switch, connection etc. as

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper

conductor single core cable in surface/ recessed medium class PVC

262 1.12 conduit alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor Metre 1000.00 373.00 373000.00

single core cable for loop earthing as required.Make:KEI,Worldcab,RR

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper

conductor single core cable in surface/ recessed medium class PVC

263 1.13 conduit alongwith 2 Nos 4 sq. mm FRLS PVC insulated copper Metre 500.00 587.00 293500.00

conductor single core cable for loop earthing as

required.Make:KEI,Worldcab,RR Kable,Bonton

Supplying and fixing of call bell / buzzer suitable for single phase,230 volt

complete as required.

266 SUB-HEAD III - FANS FIXTURES:

267 NS-1 Supply Installation Testing and Commissioning Fresh air fan 250 mm Each 4.00 3669.00 14676.00

Supply Installation Testing and Commissioning of wall fan 400 mm

268 NS-2 energy saving with remote control Each 5.00 3254.00 16270.00

Supply of decorative wall bracket having canopy arm chrome lamp cup

270 NS-3 with E27 lamp holder. Dimension: L180XW120XH300mm (±2mm). nos 10.00 1650.00 16500.00

Supply of 250mm Dia X 90 mm Height 3000K LED Inground light with

Non- Integral driver & completely made in India luminaire. The

luminaire’s shall be made of Aluminum die cast housing duly Powder

coated. The complete luminaire has IP67 & IK10 protection and it

comprises of high purity integrated poly carbonate Lens.The LEDs shall

have minimum CRI ≥80 (White LED) & shall have SDCM≤5. The

271 NS-4 luminaire shall have wattage 36W and shall deliver 1800 lumens. Beam nos 8.00 12300.00 98400.00

angle of the Luminaire shall be 60 deg .Fixture shall operating

temperature range of 0°C to 45°C. Input Voltage Range of 24V DC,

Integrated DMX Decoder,No need to additional external decoder. The

luminaire shall have declared life of 50,000 burning hours at L70.

Luminaire and Driver must be made in India with same brand.

Supply of 1000 mm length X 46.5 mm Width X 75mm Height of 3000K

Linear Wall Washer with Integral driver & completely made in India

luminaire. Luminaire must use Single LED of Chip and shall be made of

Extruded aluminum housing powder coated in grey. The complete

luminaire has IP66 & IK06 protection and it comprises of high purity

integrated poly carbonate Lens.The LEDs shall have minimum CRI ≥80

272 NS-5 (White LED) & shall have SDCM≤5. The luminaire shall have wattage nos 20.00 15500.00 310000.00

20W and shall deliver 2200 lumens. Beam angle of the Luminaire shall

be Asymetric optics .Fixture shall operating temperature range of 0°C to

45°C.Input Voltage Range of 140-270V AC. The luminaire shall have

declared life of 50,000 burning hours at L70. Luminaire and Driver must

be made in India with same brand.

Supply of 300 mm length X 46.5 mm Width X 75mm Height of 3000K

Linear Wall Washer with Integral driver & completely made in India

luminaire. Luminaire must use Single LED of Chip and shall be made of

Extruded aluminum housing powder coated in grey. The complete

luminaire has IP66 & IK06 protection and it comprises of high purity

integrated poly carbonate Lens.The LEDs shall have minimum CRI ≥80

273 NS-6 (White LED) & shall have SDCM≤5. The luminaire shall have wattage nos 10.00 10230.00 102300.00

10W and shall deliver 700 lumens. Beam angle of the Luminaire shall be

15 deg .Fixture shall operating temperature range of 0°C to 45°C. Input

Voltage Range of 140-270V AC. The luminaire shall have declared life of

50,000 burning hours at L70.Luminaire and Driver must be made in India

with same brand.

Sl. No. DESCRIPTION UNIT Qty RATE Amount (in Rs)

Supply of 16mmX16mm of 5 meters length 3000K Flexible strip led light

with Non- Integral driver.The luminaire’s shall be made of Silicon

extrusion with high-efficiency, high grade appearance, soft bend flexibility

& Option of Top bend , the same shall be so designed with completely

made in India luminaire. The luminaire shall have silicon glue between

optical cover & LED chamber to ensure proper IP67 protection. No need

274 NS-7 external decoder.The LEDs shall have minimum CRI ≥80 (White Light)& Spool 10.00 17655.00 176550.00

shall have SDCM≤5. The luminaire shall have system wattage of 14

Watt/meter and shall deliver 714 lumens. Fixture shall operating

temperature range of 0°C to 45°C. The fixture shall have an Non integral

driver with input voltage for 220-240 VAC, 50/60Hz. The luminaire shall

have declared life of 50,000 burning hours.

Supply of Magnetic Foldable LED Light with collimeter lens of System

Wattage 12W in Black Color Housing. The lights can be easily attach of

de-attach from the track channel. The magnetic lamp inside with

275 NS-8 dimmable driver, match with transformer dimming. CT-3000/4000K, nos 10.00 1850.00 18500.00

CRI-80 Watt- 12W Beam Angle 36° width - 22mm Length -220mm

height -110mm Tolerence of ± 5mm.

Supply of Magnetic cylindrical track Light with collimeter lens of System

Wattage 12W in Black Color Housing. The lights can be easily attach of

de-attach from the track channel. The magnetic lamp inside with

276 NS-9 dimmable driver, match with transformer dimming. CT-3000/4000K, nos 15.00 1750.00 26250.00

CRI-80 Watt- 12W Beam Angle 24°, Dia Ø45, length: 100mm,

Tolerence of ± 5mm.

277 NS-10 Supply of 1 mtr magneto recessed mounted track. nos 13.00 1850.00 24050.00

Supply of Magnetic Track Driver Available in 200W Surge Protection

278 NS-11 3KVA ,48V Split Transformer (external power supply) to be rquired to nos 5.00 4550.00 22750.00

install as per the site requirement.

Supply of Ø196 mm dia CCT: 3000K Circular Flood light with Non-

integral driver & completely made in India luminaire. The luminaire’s shall

be made of Aluminum die cast housing duly Powder coated. The

complete luminaire has IP66 & IK08 protection and it comprises of high

purity integrated poly carbonate Lens.The LEDs shall have minimum CRI

≥80 (Standard White Light) & shall have SDCM≤5. The luminaire shall

279 NS-12 have system wattage 48W and shall deliver 3840 lumens. Beam angle of nos 10.00 24500.00 245000.00

the Luminaire shall be 11/15deg .Fixture shall operating temperature

range of 0°C to 45°C. The luminaire shall have declared life of 50,000

burning hours at L70. Brand name shall be embossed on each an every

light fixtures. Dimension: Ø196 X 104.3mm(±5mm) excluding bracket

and weight: 3Kg

Supply of 1000 mm CCT: 3000K Linear Wall Washer with Non-integral

driver & completely made in India luminaire. The luminaire’s shall be

made of Extruded aluminum housing powder coated in grey. The

complete luminaire has IP66 & IK07 protection and it comprises of high

purity integrated poly carbonate Lens.The LEDs shall have minimum CRI

≥80 (Standard White Light) & shall have SDCM≤5. The luminaire shall

280 NS-13 have system wattage 48W and shall deliver 2640 lumens. Beam angle of nos 40.00 16500.00 660000.00

the Luminaire shall be 15° X 15°(±5%). Fixture shall operating

temperature range of 0°C to 45°C. The luminaire shall have declared life

of 50,000 burning hours at L70.TBrand name shall be embossed on each

an every light fixtures. Dimension: 1000 X 35 X 39mm (±5mm) excluding

bracket, Weight: 1.1Kg

Supply of 1000 mm CCT: 3000K Linear Wall Washer with Non-integral

driver & completely made in India luminaire. The luminaire’s shall be

made of Extruded aluminum housing powder coated in grey. The

complete luminaire has IP66 & IK07 protection and it comprises of high

purity integrated poly carbonate Lens.The LEDs shall have minimum CRI

≥80 (Standard White Light) & shall have SDCM≤5. The luminaire shall

281 NS-14 have system wattage 72W and shall deliver 3960 lumens. Beam angle of nos 30.00 23500.00 705000.00

the Luminaire shall be 15° X 15°(±5%).Fixture shall operating

temperature range of 0°C to 45°C. The luminaire shall have declared life

of 50,000 burning hours at L70. Brand name shall be embossed on each

an every light fixtures. Dimension: 1000 X 80 X 115mm (±5mm)

excluding bracket, Weight: 2.0Kg

Sl. No. DESCRIPTION UNIT Qty RATE Amount (in Rs)

Supply of Ø196 mm dia CCT: 3000K Circular Flood light with Non-

integral driver & completely made in India luminaire. The luminaire’s shall

be made of Aluminum die cast housing duly Powder coated. The

complete luminaire has IP66 & IK08 protection and it comprises of high

purity integrated poly carbonate Lens.The LEDs shall have minimum CRI

≥80 (Standard White Light) & shall have SDCM≤5. The luminaire shall

282 NS-15 have system wattage 72W and shall deliver 5760 lumens. Beam angle of nos 20.00 27500.00 550000.00

the Luminaire shall be 11/15deg .Fixture shall operating temperature

range of 0°C to 45°C. The luminaire shall have declared life of 50,000

burning hours at L70. Brand name shall be embossed on each an every

light fixtures. Dimension: Ø196 X 104.3mm(±5mm) excluding bracket

and weight: 3Kg

Supply of Isolated, constant Voltage type 240 W LED Driver enclosure

in Extruded Aluminium metal enclosure . Driver shall be made in India

compatible for RGBW luminaires with silicone potted and IP66 Protected

of same make as luminaire. Output voltage of the driver 24Vdc. Driver

efficiency should be greater than 85% at full load, THD < 10%, PF > 0.95

283 NS-16 with Under and Over Voltage Cutoff Protection and 440V withstand for 8 nos 50.00 5550.00 277500.00

hours minimum & sould have large operating input voltage range of

140V to 300V AC(nominal rated voltage – 240V) with 5KV internal surge

protection. LED driver shall have inbuilt output short circuit, over voltage

protection, Thermal Shutdown protection.

Supply, installation, testing and Commissioning of 2Core Connecting

cable/Patch cord Patch Endcap 1m - S-connector

Supply, installation, testing and Commissioning of 2Core Connecting

cable/Patch cord Patch Endcap 1m - T-connector

Supply of 100 mm Dia X 230mm Height, Surface Down Light 4000K with

Integral driver & completely made in India luminaire. The luminaire’s shall

be made of Exteruded aluminium powder coated. Optical compartment is

sealed with toughened glass using Silicon gasket ensuring IP65 & IK06

protection and lifelong performance.The LEDs shall have minimum CRI

≥70 (White LED) & shall have SDCM≤5. The luminaire shall have

wattage 30W and shall deliver 2400 lumens. Beam angle of the

286 NS-19 Luminaire shall be 60 deg. Fixture shall operating temperature range of nos 10.00 8750.00 87500.00

0°C to 45°C. Input Voltage Range of 150 - 270V AC. 2 stage Constant

current driver with Inbuilt 2kV surge protection. The luminaire shall have

declared life of 50,000 burning hours at L70. Luminaire and Driver must

be made in India with same brand. Brand name shall be embossed /

engraded on each an every light fixtures. Luminaire and Driver should be

Made in India. Luminare, Driver and controller should be with same

Supply of 65 mm Dia X 91mm Width X 200 mm Height- 2 X12W, Wall

Up - Down Light 3000K with Integral driver & completely made in India

luminaire. The luminaire’s shall be made of Die cast aluminum with Pure

polyester powder coated housing. Optical compartment is sealed with

toughened glass using Silicon gasket ensuring IP65 & IK06 protection

and lifelong performance.The LEDs shall have minimum CRI ≥80 (White

LED) & shall have SDCM≤5. The luminaire shall have wattage 2 X 12W

287 NS-20 and shall deliver 2 X 1200 lumens. Beam angle of the Luminaire shall be nos 15.00 12500.00 187500.00

29 deg. Fixture shall operating temperature range of 0°C to 45°C. Input

Voltage Range of 140 - 280V AC. 2 stage Constant current driver with

Inbuilt 3kV surge protection. The luminaire shall have declared life of

50,000 burning hours at L70. L Brand name shall be embossed /

engraded on each an every light fixtures. Luminaire and Driver should be

Made in India. Luminare, Driver and controller should be with same

Supply of Specially designed step light LED 3000K 220-240Vac CRI > 80

Input power: 2.5-3W. Electronic driver ON/OFF CE mark. IP rating IP66

288 NS-21 and impact resistance IK07. MATERIAL CHARACTERISTICS metal and nos 50.00 1800.00 90000.00

plastic housing with polycarbonate UV-resistant optical cover, aluminum

and black/grey colour.

Sl. No. DESCRIPTION UNIT Qty RATE Amount (in Rs)

Supply of 45W LED Decorative Post Top type luminaire with System

efficacy of 85 lm/W (3800 lumens), suitable for external poles of dia.

65mm to 75mm. Luminaire shall be made up of pure polyster power

coated RAL7021 pressure die cast Aluminium housing with

Polycarbonate Fresnel lens for symmetrical or street optics of same

make. All external hardwaremust be of SS304 grade. LM 80-08

compliant LEDs of EMC/ceramic package from reputed makes such as

Nichia/Cree/ Bridgelux/ Lumiled/ Osram/Seoul should be provided. LEDs

used in the product shall comply with EN 62471 for Photo-biological

safety and certificate for the same from manufacturer shall be provided.

Luminaire shall be with IP66 and IK07 protection. The LED shall be

289 NS-22 compliant with LM80-08 standard with L70 life of 50000 Hrs tested at nos 15.00 9450.00 141750.00

maximum current (Complete LM 80 test report for LED should be

submitted for 10000 hrs of testing). The LEDs used should be with CCT

of 3000 K, CRI of Minimum 70 and SDCM <5. LEDs must be driven at

max 70% of the rated current. MCPCB with Aluminium core and copper

thickeness of 35 micron to be used for LED mounting.LED Driver shall

be silicone potted, Integrated type, Isolated, Constant Current with range

150-300V AC. Driver Efficiency > 85% & 4 KV internal surge protection,

Power factor greater than 0.95 and total harmonic distortion (THD) of

less than 10% should be integral to the luminaire.

Supply of 385mm Top Dia & 182mm Height Dark Sky Certified unique

spherical cap shape design post top & completely made in India

luminaire. The luminaire’s shall be made of Aluminum top spun cap with

die cast heatsink, duly powder coated with gray color pure polyester. The

complete luminaire has IP66 & IK08 protection and it comprises of

polycarbonate fresnel lens/street optics lens to achieve Nil up-light and

reduced light pollution on driveway as well as footpath. The LEDs shall

have minimum CRI ≥70, CCT-4000K & shall have SDCM≤5. The

290 NS-23 luminaire shall have wattage 45W as per lux requirement and shall nos 20.00 10100.00 202000.00

deliver 100 lm/W(efficacy). Beam angle of the Luminaire shall be

asymmetric type to cover driveways. Fixture shall operating temperature

range of 0°C to 45°C. Input Voltage Range of 150-300V AC. The

luminaire shall have declared life of 50,000 burning hours at L70.

Luminaire and Driver must be made in India with same brand. Suitable

for external pole dia. 65mm to 75mm. Luminaire and Driver should be

Made in India. Luminaire should have RoHS, EMI EMC as per IEC

61547, CISPR 15.

Supply of 90W SMD LED Streetlight fixture with System efficacy of

135lm/W (12150 lumens).Luminaire shall be made up of pure polyster

powder coated die cast Aluminium housing with high purity IP66 PC lens

without any glass cover, of single module of same make. The luminaire

should be in square shape with diemsion 325mm x 184mm x 110mm ±

2mm with a linear driver compartment placed on top. It should not weigh

more than 1.78 Kg ± 0.2 Kg. The housing should be made of

LM6/ADC12 Alloy, non-corrosive Single Piece pressure die-cast

aluminum, to withstand extreme environments. All external hardware

must be of SS304 grade. The name of the brand should be

embossed/engraved & should not be mentioned using sticker/screen

printing. Luminaire shall be designed with street optic LENS for uniform

light distribution. Maximum LENS dome top temperature shall be less

than 95°C at 45°C ambient temperature. LM 80-08 compliant LEDs of

EMC/ceramic package of wattage of 4W-5W from reputed makes such

as Nichia/Cree/ Bridgelux/ Lumiled/ Osram/Seoul should be provided.

291 NS-24 LEDs used in the product shall comply with EN 62471 for Photo- nos 15.00 5100.00 76500.00

biological safety and certificate for the same from manufacturer shall be

provided. Luminaire shall be with IP66 and IK10 protection. The LED

shall be compliant with LM80-08 standard with L70 life of 100000 Hrs

tested at maximum current (Complete LM 80 test report for LED should

be submitted for 10000 hrs of testing). The LEDs used should be with

CCT of 3000/4000/5700 K, CRI of Minimum 70 and SDCM of < 5. LEDs

must be driven at max 70% of the rated current. MCPCB with Aluminium

core and copper thickeness of 35 micron to be used for LED mounting.

LED Driver shall be silicone potted, Integrated type, Isolated, Constant

Current with range 140-270V AC. Driver Efficiency > 85% & 5 KV internal

surge protection along with external SPD of 10 KV mounted inside the

streetlight and firmly fixed to the housing, Power factor greater than 0.95

and total harmonic distortion (THD) of less than 10% should be integral

to the luminaire. LED Driver must have short circuit, open circuit, Auto

cut-off protection for low and high input voltage. Driver must have 440V

input voltage protection for 8 hours. Driver must be of die cast / extruded

Sl. No. DESCRIPTION UNIT Qty RATE Amount (in Rs)

Supply of LED based Spike light, housing made up of pressure die cast

aluminum Alloy with effective thermal management,sturdiness and

embossed brand name/logo name of manufacturer and optics made of

surface mount reflector with toughened. The fixture should have a

minimum system efficacy of 80lumen/Watt and a minimum system

lumen output of 640 lumens and maximum system wattage of 8

Watts.The fixture shall have a CRI of minimum 80 and beam angle: 50-

55deg. The fixture shall be designed for a system life of 50,000 hours

@70% lumen maintenance. Ingress Protection of IP67 (lamp and gear

292 NS-25 Compartment) and Mechanical Impact Resistance Rating of IK >=07, nos 50.00 2450.00 122500.00

CCT: 2700K. The fixture driver should have an operating voltage range

of 100-270 V, surge protection of >=3KV, PF >0.9, THD<10% & Driver

efficacy >80% @full load and rated voltage. Ambient temp range: 0deg

to 45deg C. The Drivers should be a potted driver not a printed circuit

board without casing, mounted inside the luminaire. The fixture should

comply with the parameters as per IS10322. . Dimension: Ø115 X 158 X

93mm & Weight including all accessories should not be more than

Supply of All-in-One integrated LED solar street light consists of solar

photovoltaic module, battery, battery management system, control

electronics, LED driver, interconnecting cables and pole mounting piece

integrated into the luminaire as a single unit. Solar streetlight with IP65

ingress protection having a system wattage of note more than 70 Watt

with minimum 119000 system lumen output, 95Wp high efficiency

monocrystalline solar panel, highly efficient MPPT based charge

controller and 12.8V, 24 Ah Lithium Ferro Phosphate (LiFePO4) battery

with proper battery management system which provides higher life of

>2000 cycles. Light fixture should operate at Full Power up to 6Hrs.(At

fully charged battery) and Saving mode up to 27Hrs.(At fully charged

battery). System efficacy:>170lm/W and MPPT charge controller with

90% efficiency. Fixture should have no load current less than 10mA,

293 NS-26 Charging current less than 4A. Typical correlated colour temperature nos 10.00 88500.00 885000.00

should be 5700K±500K with CRI>70. It should have Integral PIR sensor

for motion detection to ensure battery optimisation with help of a suitable

dimming profile. The luminaire shall have inbuilt hybrid power supply

option that can charge the battery during non-sunny days automatically

from the grid. The luminaire should be made from single piece extruded

aluminium & IK08 impact resistance certified housing (IK rating of motion

sensor is not included), with anti-corrosive coating and must have a UV

stabilized polycarbonate cover. The luminaire shall have a specially

designed pole mounting piece that enables installation at varying tilts

from 0 to 15 degrees for optimal light distribution. System should have

Smart self-diagnostic feature for indicating battery charging, cut off &

fault if any. Dimension: 1260X410X60mm, Weight: 27.5Kg (approx.)

Supply of 9.0 Mtr. long G.I. Octagonal with Single arm, pole shall be

fabricated with following dia pipes 155 mm x 3.0 mm (Bottom) and 70

mm x 3.0 mm (top) with a bottom plate of size 260x260x16mm having

necessary gusset plate etc. with 1 Nos. 1.0 Mtr. long arm as per light

fixture or proper provision to mount 1 nos. street light fixtures, including

Concrete Foundation of size 350 x 350 x 1000 mm in precast RCC block

with 4 nos. "J" hook (Bolt) of 24 mm dia and length 750 mm. complete

with Nut & washer. The foundation shall be completes with all respect

294 NS-27 including finishing and Earthing is required. as per specification including nos 10.00 19900.00 199000.00

excavation, wiring with 3Cx2.5 sq.mm copper wire from the integral

control box to street light fixture with four number 20A copper bus bar

along with supports of suitable size, 1 no 10A MCB, neutral link &

connection to the lamp through the pole, connection to the integral

control box through the concrete foundation with suitable size G.I. Pipes

& painting with two coats of primer & two coats of enamel paint as

Supply of 4.0 mtr Al step tubular pole, Pole should have Anti rust coating

& should be PU Painted, 4 nos of foundation nut & bolt(16mm dia & 600

mm long with templates) with a base plate of 250mmx250mm, Base

Plate thickness- 15 mm. Pole Thickness-3.0mm. Pole Base OD up to 1

295 NS-28 mtr -1.2 mtr of 102mm dia, then 6 mm OD Pole should have a din rail for nos 10.00 8650.00 86500.00

MCB mounting provision with Bakelite sheet and 32 mm Electrical

Connector with Bubble sheet Packing suitable for BOQ complete as

Sl. No. DESCRIPTION UNIT Qty RATE Amount (in Rs)

Supply of 11W LED Decorative Bollard with System efficacy of 70 lm/W

(770 lumens). Luminaire shall be made up of pure polyester power

coated casted Aluminium housing with seamless polycarbonate diffuser

and asymetrical photometric distribution, having dimension of

150X70mm with height of 800mm. All external hardware must be of

SS304 grade. LM 80-08 compliant LEDs of EMC/ceramic package from

reputed makes such as Nichia/Cree/ Bridgelux/ Lumiled/ Osram/Seoul

should be provided. LEDs used in the product shall comply with EN

62471 for Photo-biological safety and certificate for the same from

manufacturer shall be provided. Luminaire shall be with IP65 and IK10

protection. The LED shall be compliant with LM80-08 standard with L70

life of 50000 Hrs tested at maximum current (Complete LM 80 test report

for LED should be submitted for 10000 hrs of testing). The LEDs used

should be with CCT of 4000/5700 K, CRI of Minimum 80 and SDCM <5.

LEDs must be driven at max 70% of the rated current. MCPCB with

Aluminium core and copper thickness of 35 micron to be used for LED

mounting. LED Driver shall be silicone potted, Integrated type, Isolated,

Constant Current with range 100-300V AC. Driver Efficiency > 80% & 3

KV internal surge protection, Power factor greater than 0.95 and total

harmonic distortion (THD) of less than 10% should be integral to the

luminaire. Compliance to Indian Standards of IS10322 Part 5 / Sect

IS 16108 : 2012 should be there. Luminaire should have RoHS, EMI

EMC as per IEC 61547.

Supply, erection, testing and commissioning as a complete unit suitable

for continuous outdoor operation under the climatic and terrain conditions

of the region, including low temperatures and high wind conditions. The

mast of height 30mtr shall be fabricated from high-strength structural

steel conforming to IS 2062, of polygonal, continuously tapered

construction with slip-jointed sections, and hot-dip galvanized after

fabrication in accordance with IS 4759/IS 2629 with a minimum average

zinc coating thickness of 85 microns. The complete structure, including

lantern carriage and luminaires, shall be designed to withstand wind

loads as per IS 875 (Part 3) for the applicable basic wind speed and

seismic forces as per IS 1893, with adequate factor of safety as

prescribed by relevant Indian Standards. The symmetrical high mast

shall be provided with a hot-dip galvanized lantern carriage suitable for

uniform mounting of 12nos of 500W LED floodlights, complete with an

electrically operated, self-locking raising and lowering mechanism

consisting of winch, galvanized steel wire ropes, pulleys, guides, and

safety locking arrangements. Internal wiring shall be carried out with

FRLS/XLPE insulated copper conductors routed through the mast, and a

weatherproof base compartment shall be provided to house the winch

motor, control gear, and terminal blocks. The system shall include two

separate earthing points and integrated lightning protection in

accordance with IS 3043. The RCC foundation shall be designed based

on soil investigation and wind loading, using minimum M25 grade

concrete, complete with anchor bolts, base plate, and templates, with

suitable feeder pillar. OEM to submit foundation drawings & structural

design calculations fully complying with applicable Indian Standards.

Sl. No. DESCRIPTION UNIT Qty RATE Amount (in Rs)

Supply of 500W SMD LED Floodlight fixture with System efficacy of 125

lm/W (62500 lumens). Luminaire shall be made up of LM6/ADC12 Alloy,

non-corrosive, pure polyster power coated die cast Aluminium housing

with PC lens. Lumianire should be of dimension 319mm x 677 mm x

97mm height ± 5mm height and the approximate weight should be within

the 14.5Kg ± 0.5Kg. Luminaire should be available with 25° and 60°

beam angle option. Luminaire should be made of four individual modules

of 100W to 125W each. All external hardware must be of SS304 grade.

LM 80-08 compliant LEDs of EMC/ceramic package of wattage of 5W

from reputed makes such as Nichia/Cree/ Bridgelux/ Lumiled/

Osram/Seoul should be provided. LEDs used in the product shall comply

with EN 62471 for Photo-biological safety and certificate for the same

from manufacturer shall be provided. Maximum LENS dome top

temperature shall be less than 95°C at 45°C ambient temperature.

Luminaire shall be with IP66 and IK07 protection. It should be cabable to

operating under ambient temperature range of -10°C to +45°C. The LED

298 NS-31 shall be compliant with LM80-08 standard with L70 life of 50000 Hrs nos 12.00 40200.00 482400.00

tested at maximum current (Complete LM 80 test report for LED should

be submitted for 10000 hrs of testing). The LEDs used should be with

CCT of 5700 K, CRI of Minimum 70 and SDCM < 5. LEDs must be

driven at max 70% of the rated current. MCPCB with Aluminium core and

copper thickeness of 35 micron to be used for LED mounting. LED Driver

shall be silicone potted, Integrated type, Isolated, Constant Current with

range 140-280V AC. Driver Efficiency > 85% & 4 KV internal surge

protection with additional 10KV SPD mounted inside the luminaire and

firmly fixed to the housing, Power factor greater than 0.95 and total

harmonic distortion (THD) of less than 10% should be integral to the

luminaire. LED Driver must have short circuit, open circuit, Auto cut-off

protection for low and high input voltage. Individual drivers should be

provided with individual modules along with ventilated enclousure to hide

the wirings. Driver must be with Aluminium casing.

SubTotal (Electrical Works) - B 10809173.00

Grand Total (Civil (A) + Electrical (B) ) 52555777.91

Grand Total (Civil (A) + Electrical (B) ) 52555777.91