REPAIR MAINT OF CEILING FANS EXHAUST FANS CONNECTED WORKS AT AF STATION GWALIOR

Amount

Disconnecting , taking down & removing carefully the existing ceiling fan, exhaust fans, wall bracket fans etc. of any description, any sweep and from any position / locations (i.e. Md Accn/ OTM Accn) for repairs / servicing / overhauling / painting / numbering etc dismantlinf and opening of the checking serviceablity of parts, overhauling, Hanging / fixing the fans in position after repairs i.e overhauling by necessary cleaning, oiling & greasing ,removing & replacement of defective/ unserviceable parts,with new parts, reassembling the fans, making necessary adjustment , proper alignment of blades,connecting to existing electric sources and testing at site to the entire satisfaction of Engineer-in-Charge complete all as specified and directed.

Note: - (i) The replacement of defective / nonfunctional parts shall be measured & paid for separately as “Supply only” under appropriate item of Sch ‘A’ and fixing charges for new items are deemed to be included under this item.

(ii) Burnt out windings replaced, shall be measured and paid for separately under appropriate item of Sch ‘A’ for rewinding.

(iii) The rates for above items are deemed to include for transportation to & fro of fans to workshop if required and approved by the Engineer-in-charge for necessary repairs.

(iv) Writing of fan No. and painting of fans shall be measured and paid for separately under appropriate item of Sch ‘A’

Taking out & removing old burnt-out windings of electric fans of any description and rewinding of fan motor with appropriate size super enameled copper wire (Make : Atlas/Finolex/Devi Dayal)as approved by the Engineer-in-charge including insulating material such as illuminous paper, Letherized paper, cotton tape, glass sleeving, insulating varnish etc testing at workshop and transportation to site, connecting and testing on full load to the entire satisfaction of Engineer-in-charge for the following Fans:-

(a) Rewinding of motor of ceiling fans 1200/1400 mm sweep.

(b) Rewinding of motor of exhaust fans of 225/230 mm sweep.

(c) Rewinding of motor of exhaust fans of 300/375 mm sweep.

(d) Rewinding of motor of exhaust fans of 450 mm sweep.

(d) Rewinding of motor of wall mounted fan

Supply only the following new parts suitable for the ceiling/ exhaust fans, wall bracket fans & pedestal fans, air circulating fans etc. of any description, any sweep :-

(a) Supplying only ball bearing No 6200 (Make SKF/NRB/NBC) )

(b) Supplying only ball bearing No 6201 (Make SKF/NRB/NBC) )

(c) Supplying only ball bearing No 6202 (Make SKF/NRB/NBC) )

(d) Supplying only ball bearing No 6203 (Make SKF/NRB/NBC) )

(e) Supply only gun metal bushes of any description and size to suit existing motor shaft including grinding & polishing of fan motor shaft to required shape/size.

(f) Supplying only capacitor of capacity 2.5 mfd (PVC body) (Make:- EPCOS/JYOTI/ USHA)

(g) Supplying only capacitor of capacity 3.15 mfd (PVC body) (Make:- EPCOS/JYOTI/USHA)

(h) Supplying only capacitor of capacity 4 mfd (PVC body) (Make:- EPCOS/JYOTI/USHA)

(i) Supplying only complete hanging assembly set comprising with rubber reel, MS clamps, nuts, bolts with one lock hole and lock pins suitable for any type of fans & down rods.

(j) Supply only PVC canopy of any description and suitable for any type & any make of fan.

(k) Supplying only PVC fan blade assembly with necessary MS nuts, bolts & washers suitable for exhaust fans of any descriptions & of 230 mm sweep. (Note: Set of three blades shall be measured as one unit and make of assembly shall be as approved by GE.)

(l) Supplying only aluminium cast metal fan blade assembly with necessary MS nuts, bolts & washers suitable for exhaust fans of any descriptions & of 300 mm sweep. (Note: Set of three blades shall be measured as one unit and make of assembly shall be as approved by GE.)

(m) Supplying only aluminium cast metal fan blade assembly with necessary MS nuts, bolts & washers suitable for exhaust fans of any descriptions & of 450 mm sweep.(Note: Set of three blades shall be measured as one unit and make of assembly shall be as approved by GE.)

(n) Supply only PVC insulated and sheathed, round flexible cable, three core of size 23/0.0076 with copper conductor in pieces for connecting fans. ( Make :Havell’s / Finolex / Gloster / National/ Plaza )

(o) Supply only MS nuts & bolts with one hole washer & lock pin of suitable size for hanging assembly complete.

(p) Supply only rubber real of suitable size of hanging assembly complete.

(q) Supply only condensor cap pvc body

(r) Supply only 300mm long down rod 20mm dia, MS tube light grade, duly finished with powder coating of white colour, including necessary holes and threading etc. complete all as specified.

(s) Supply only 600mm long down rod 20mm dia, MS tube light grade, duly finished with powder coating of white colour, including necessary holes and threading etc. complete all as specified.

(t) Supply only 1200mm long down rod 20mm dia, MS tube light grade, duly finished with powder coating of white colour, including necessary holes and threading etc. complete all as specified.

(u) Supply only 1800mm long down rod 20mm dia, MS tube light grade, duly finished with powder coating of white colour, including necessary holes and threading etc. complete all as specified.

Supply only mild steel fan blade of size 1200 to 1400 mm and of standard thickness (Factory Made) duly balanced and painted of required colour at site complete all as specified and directed.

Supply only Exhaust fan clamp (leg) for 225/300mm exhaust fan as per sample (set of 3/4) including rubber packing and clamp bolt complete all as specified and directed

Supply only Exhaust fan clamp (leg) for 450 mm exhaust fan as per sample (set of 3/4) including rubber packing and clamp bolt complete all as specified and directed

Supply only Exhaust fan frame for 225/300mm exhaust fan as per sample complete all as specified and directed

Supply only Exhaust fan frame for 450 mm exhaust fan as per sample complete all as specified and directed

M&L for taking down carefully serviceable ceiling fan/exhaust fan/cabin fan (any make any size) from any building and opening the same cleaning each part, oiling and greasing including replacement of worn out parts i.e nut, bolt, screw, split pin, rubber real and re-fixing in the same position after repair complete all as specified and directed.

Disconnecting & removing unserviceable capacitor from existing ceiling fan, exhaust fans, wall bracket fans & pedestal fans, air circulating fans etc. of any description, any sweep fixed in position at any locations (i.e. Md Accn/ OTM Accn / hangers) for replacement with new capacitor of following capacity and testing at site to the entire satisfaction of Engineer-in-Charge complete all as specified and directed.:-

(a) Capacitor of capacity 2.5 mfd (PVC body)(Make:EPCOS/ JYOTI/USHA)

(b) Capacitor of capacity 4 mfd (PVC body) (Make:- EPCOS/ JYOTI/USHA)

Taking down existing worn out louvers of any description , in any position and supplying & fixing new louvers made out of MS sheet 22 gauge thick suitable for exhaust fan of 230/300mm sweep all as specified & directed by Engineer-in-Charge.

( Note: The louvers shall be of shape, size and pattern as approved by the Engineer-in-Charge duly painted with two of synthetic enamel paint over a coat of red oxide primer)

All as per item No.10 above but suitable for exhaust fan of 450 mm sweep

Disconnecting & taking out old existing unserviceable fan regulator of any description & in any position / location.

Supplying, fixing, connecting & testing of fan regulator (Electronic step type) all as specified & directed by Engineer-in-Charge (Make:- Anchor/Crompton/Usha/Bajaj/Cona)

Supplying, fixing fan hook made of of flat iron of suitable size and length, fixed with and including nut, bolts of suitable size including drilling holes for grouting nut, bolt etc complete all as specified & directed.

S&F MS clamps for fixing of fan hook as per sample made out of 5 mm thick MS Falt including necessary cutting, drilling, welding and provision of necessary nut and bolts etc complete all as specified and directed.

M&L for repair to ceiling fan/ exhaust fan /wall mounted fan shaft by means of remetalling, grinding & polishing to make with the original size and shape and suitable for fixing of bearing of bush and repairing of bearing housing as required complete all as specified and directed.

M & L for painting of existing fans of any description (ceiling fan/exhaust fan/Air circulators/Wall mounted fans/Pedestal fan) with applying one coat of synthetic enamel paint (White) by spray machine including preparation of existing decorated surfaces of fans including engraving MES No. of fan in capital letters of height not less than 20 mm on fan body all as specified and directed.

S&F in replacement of Armature with shaft for ceiling fas 1200/1400 mm sweep as per sample.

S&F in replacement of top & bottom cover of armature suitable for ceiling fas 1200/1400 mm sweep as per sample.

Taking down carefully condensor, down rod, canopy, fan blades, nut, bolt and washers, rubber seal, condensor cap, exhaust fan clamp, exhaust fan frame with existing surface complete all as specified and directed. NOTE:- (a) Adequate no of electricians and helpers shall be present at office of AGE (E/M) AF AA Gwalior at 9AM every day for taking instructions regarding repair works with and including T&P and transporation required in domestic area of AF station Gwalior. (b) Additional/Alternative electrician shall also be deployed to attend work on sundays/holidays for faults/defects/complaints. (c ) All labour effect for above mentioned work is deemed to be included in quoted rates by bidder.

Supply only exhaust fan motor for 225/250mm sweep exhaust fan as per sample complete all as specifed and directed.

Supply only exhaust fan motor for 300mm sweep exhaust fan as per sample complete all as specifed and directed.

Supply only PVC insulation tape 25mm dia for electric work complete all as specified and directed.

S&F in repair of exhaust fan steel body AC single phase 230V with blades, frame and louvers of sweep 300mm complete all as specified and directed.

S&F in repair of exhaust fan made of sturdy engineering plastic complete louvers shutter, 230V, 50Hz, 1200RPM copper winding of sweep 300mm complete all as specified and directed.

S&F in repair of exhaust fan made of sturdy engineering plastic complete louvers shutter, 230V, 50Hz, 900RPM copper winding of sweep 225/250mm complete all as specified and directed.

S&F in replacement 36W LED recess softline luminaire suitable for armstrong/grid ceiling with high brightness SMD LEDs as light source, environmental friendly, new generation, aesthetically designed, ultra modern recess mounting luminaire with fixture size 600x600x35mm complete with LED tube and all accessories specified and directed. Make : Havells cat part No PLUTONEO2X2PLR36WLED840S /CG cat part No LCTLSN36-CDL/Surya cat part No. SLEDS36 22R

S&F in repair MCB single pole 6 to 32 Amps, "B" series, 10KA, 240 Volts complete all as specified Make:Legrand/ABB/Siemens

S&F in repair MCB single pole and neutral 40 to 63 Amps, "C" series, 10KA, 240 Volts complete all as specified Make:Legrand/ABB/Siemens

S&F in repair MCB TPN/FP 40 to 100 Amps, "B" series, 10KA, 240 Volts complete all as specified Make:Legrand/ABB/Siemens

keerti enterprises

M/s Dinesh Kumar

M/s KKPARASHAR

UNIVERSAL AGENCY