SPECIAL REPAIR TO BLDG NO P-55/2, T-791, T-910 AND PROVN OF BATHROOM CUM TOILET NEAR BLDG NO P-93 AT LEIMAKHONG MIL STN

Amount

B/R work

Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dense soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cms thick in soils complete all as specified and as directed.

Removing excavated material not exc 50m and depositing where directed at a level not exc 1.5m above the starting point complete all as specified and directed.

Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified and directed.

Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed.

M&L for Hardcore of broken stone or boulder of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M & L for PCC M-7.5 grade (Nominal mix) using 40mm graded crushed stone aggregate as in foundation, filling and mass concrete complete all as specified and as directed.

M&L for PCC M-10 grade (Nominal Mix) using 40mm graded crushed stone aggregate as in surface channel and drains complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. complete all as specified and directed.

Add or deduct for each 25 mm girth or part thereof over or under 30cm against Item No 11 above and ditto (For adjustment only)

M&L for RCC M-15 grade (Nominal mix) using 20mm graded crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for RCC M-15 grade (Nominal mix) using 20mm graded crushed stone aggregate as in chajjas and the like complete all as specified and directed.

M & L for PCC M-15 grade (Nominal mix) using 12.5mm graded crushed stone aggregate as in coping including necessary formwork complete all as specified and as directed.

M & L for PCC M-10 grade (Nominal mix) using 20mm graded crushed stone aggregate as in hold fast complete all as specified and as directed.

M&L for brick work with subclass ‘B’ bricks, (locally available best quality) old size bricks straight or curved on plan exc 6 m means radius, built in cement mortar (1:6) complete all as specified and directed.

Ditto all as per Sl item No. 17.00 here-in-above but except brick (NOTE: Seviceable brick obtained from demolition under Sl item No 167.00 here-in-after shall be reused under the item)

M & L for brick work with sub class ‘B’ brick, old size (locally available best quality) straight or curved on plan to any radius in half brick thick wall built in cement mortar (1:4) complete all as specified and directed.

Use and waste for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), rough finished surface of concrete complete all as specified and directed

Use and waste for formwork to chajjas including edges, rough finished surface of concrete complete all as specified and directed

M&L for well seasoned 2nd class hard wood in scantling, clean sawn timber framed work complete all as specified and directed.

Ditto all as per Sl item No. 22.00 here-in-above but except scantling (NOTE: Seviceable wooden scantling obtained from dismantling under Sl item No 170.00 here-in-after shall be reused under the item)

M&L for 2nd class hardwood weather boarding, clean sawn, plain, 20mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps complete all as specified and directed

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc. 1.5 sqm but not exc. 4 sqm each and removing all unserviceable materials from site complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sq. m each and removing all unserviceable materials from site complete all as specified and directed.

Taking down shutters of any description exc. 1 sqm and not exc. 2 sqm each and removing all unserviceable materials from site complete all as specified and directed.

S&F 2nd class hardwood plain solid straight chowkhats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and directed.

S&F 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F for 35mm thick well seasoned 2nd class hardwood glazed and skeleton shutter open rebated and prepared to receive glass etc. (without sash bar) edges of framing plain chamfered or rounded fitted with cut and mitred bead for securing gauge etc size of members of shutter as specified in SSR Part-I section 8 clause 8.24(a) complete all as specified and directed.

S&F for 30mm thick well seasoned 2nd class hardwood glazed and skeleton shutter open rebated and prepared to receive glass etc. (with sash bar) edges of framing plain chamfered or rounded fitted with cut and mitred bead for securing gauge etc size of members of shutter as specified in SSR Part-I section 8 clause 8.24(b) complete all as specified and directed.

S&F factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F 75mm long butt hinges medium weight cold rolled mild steel complete all as specified and directed.

S&F 100mm long butt hinges medium weight cold rolled mild steel complete all as specified and directed.

S&F 100mm long mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed complete all as specified and directed.

S&F 150mm long mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed complete all as specified and directed.

S&F 100mm long Mild steel pressed handles, oval type, stove enamelled black complete all as specified and directed.

S&F 150mm long Mild steel pressed handles, oval type, stove enamelled black complete all as specified and directed.

S&F Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed 300mm long complete all as specified and as directed.

S&F MS 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor with 140mm overall length of cover plate complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width or aperture 1.40mm complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width or aperture 1.18mm complete all as specified and directed.

S&F in repairs galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width or aperture 1.18mm complete all as specified and directed.

S&F 18/19mm thick particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work complete all as specified and directed

S&F 0.90mm thick decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed

S&F 2nd class hardwood lipping for cupboard shutter, wrought, sectional area n exc 3Sqcm complete all as specified and directed.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised, 30mm width of flaps complete all as specified and directed

S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and directed

S&F magnetic door catches of standard size, mild steel body and striking plate including letting in and fixed complete all as specified and directed.

S& F aluminium anodised sliding window, 3 track system, fully glazed fitted with one side visible glass of 5.5mm thick, shutter frame size 44 x 24 x 1.8mm including chowkat of size 80 x 40 x 1.8mm and sliding fly proof shutter (using stainless steel wire cloth of gauge 0.50mm dia and aparture 1.18mm) with three track , including aluminium grill on out side throughout & providing necessary jointing cleats ,glazing clips,rubber packing, anodised aluminium snap beading,handle,screw complete all as specified and as directed.

S&F Structural steel work in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe 410-W (Grade E-250) quality-A complete all as specified and as directed.

S&F Structural steel work in Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to Fe 410-W (Grade E-250) quality-A complete all as specified and as directed.

M&L for structural steel work in Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe- 290 (Gde E- 165) complete all as specified and directed.

M&L for MS works as in Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts;posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L for MS work as in framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for TMT bars 6mm to 8mm dia, cut to length, bent to shape as required including cranking, bending and binding with mild steel wire(annealed) not less than 0.9mm dia as in reinforcement bar complete all as specified and directed

S&F band, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required hooks (stay), heavy, for large hasps and staples, chains, hand made sliding bolts, clamps, holdfasts, wall ties, hooks for hanging fans plain angle cleats complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed

S&F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges, hips, valley gutters, drip, straight flashing etc fixed with self tapping screws complete all as specified and directed

S&F 0.63mm thick galvanised corrugated mild steel sheeting with two corrugation side lap fixed with 'J' type cranked hook bolt and washer in roof, wall etc. with grade of zinc coating 275 complete all as specified and directed.

Ditto all as per Sl item No. 62 here-in-above but except sheeting (NOTE: Seviceable 0.63mm thick galvanised corrugated mild steel/plain sheets obtained from dismantling under Sl item No 164.00 here-in-after shall be reused under the item)

S&F 0.63mm plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip, wall cladding and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and directed.

M & L for 6mm thick plywood (no of ply 05), grade BWR, type BB, fixed with nails to timber frame work in ceiling complete all as specified and directed.

M&L for 6mm thick cover fillets of standard hard board, 40mm wide, and fixing with screws complete all as specified and directed.

M & L for PCC M-15 grade (Nominal mix) using 12.5mm graded crushed stone aggregate as in in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and as directed.

M&L rendering 15mm thick on roof slab in cement mortar 1:4 using water proofing compound @2% by weight or cement as per manufacture instruction and finishing even and smooth without using extra cement all as specified. (Note: Plastering shall be carried out using Dimapur Sand. WPC will be measured and paid separately)

M & L for water proofing treatment to RCC roof slab including parapet comprising with the following course of treatment/specifications from bottom to top:- (a) Applying bituminous primer @ 100 gm per Sqm over plastered surfaces of roof including parapet surfaces. (Make: “TANK MASTIC” of STP Ltd or “EMUFALTE” of Texsa India Ltd/IWL India Ltd) (b) One layer of APP based polymeric membrane of approved manufacturer, 3mm thick, weight not less than 3.50 Kgs per Sqm, reinforced with non woven polyester fabric or weight not less than 150 gms per Sqm. Polymeric membrane shall be taken to a height 60cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing. (Note: (i) Laying of APP based polymeric membrane shall be done by torch on method or as per manufacturers instructions. (ii) A minimum overlap of 100mm and 75mm should be made in the end and sides of the polymeric membrane respectively and sealed all overlaps and joints as manufacturers instructions. (iii) The make of polymeric membrane shall be “SUPER THERMOLAY” of STP Ltd or “MOPLY FP” of Texsa India Ltd./IWL India Ltd) (c) Applying two coats of bituminous aluminum paint on top of APP membrane.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises complete all as specified and directed.

M&L 75mm thick PCC M-10 grade (Nominal Mix) using 40mm graded crushed stone aggregate in sub base, finishes even and rough complete all as specified and directed.

M&L 25mm thick PCC M-15 grade (Nominal Mix) using 12.5mm graded crushed stone aggregate in floor, finishes even and rough to receive floor tiles complete all as specified and directed.

M&L 40mm thick PCC M-15 grade (Nominal Mix) using 20mm graded crushed stone aggregate in floor, finishes even and rough to receive floor finishes complete all as specified and directed.

M & L for 15mm thick screed bed or bedding layer in cement mortar (1:6) for laying floor tiles etc complete all as specified and directed.

M & L for 20mm thick screed bed or bedding layer in cement mortar (1:6) for laying kota stone/granite/chequerred tiles complete all as specified and directed.

M&L coloured non-skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm as in floor, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L coloured non-skid ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floor, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L coloured non-skid ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm as in floor, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises complete all as specified and directed.

S&F Glazed ceramic tiles in vertical surface 300x 200x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tile including 10mm thick cement mortar backing in cement mortar (1:4) complete all as specified and directed.

S&F Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tile including 10mm thick cement mortar backing in CM (1:4) complete all as specified and directed.

S&F 20mm thick Granite (of any type) tiles, machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed.

S&F 20mm thick Granite (of any type) tiles machine cut, in skirting/ dado laid over and including 12mm thick cement screed base in cement mortar 1:4 and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed.

M&L for machine cut kota stone slab flooring 20- 25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed

M&L for machine cut kota stone in riser of steps, skirting, dado and pillar, 20- 25mm thick laid over and including 12mm thick cement screed base in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed

M&L Chequered cement concrete tiles 20cm x 20cm x 25mm thick,set, jointed and pointed in neat cement slurry with grey cement and pigment in floors to match complete all as specified and directed.

M&L for 75mm thick PCC M-10 grade (Nominal Mix) using 40mm graded crushed stone aggregate as in plinth protection finishing surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for forming Contraction (Dummy) joints 75mm deep x 10mm wide, filled with sealing compound grade 'A' complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc, including raking out joints hacking for key, scrubbing down with water etc. complete all as specified and directed.

M&L rendering 15mm thick on fair faces of brick work in cement mortar 1:4 using water proofing compound @2% by weight or cement as per manufacture instruction and finishing even and smooth without using extra cement all as specified. (Note: Plastering shall be carried out using Dimapur Sand. WPC will be measured and paid separately)

M & L for rendering 15mm thick plaster in cement mortar (1:6) on other than fair faces of brick work or on concrete surfaces finished even and smooth without using extra cement complete all as specified and directed. (Note: Plastering shall be carried out using Dimapur Sand)

M & L for rendering 10mm thick plaster in cement mortar (1:6) on fair faces of brick work or on concrete surfaces finished even and smooth without using extra cement complete all as specified and directed. (Note: Plastering shall be carried out using Dimapur Sand)

M & L for rendering 10mm thick plaster in cement mortar (1:4) on ceiling surfaces finished even and smooth without using extra cement complete all as specified and directed. (Note: Plastering shall be carried out using Dimapur Sand)

Supply only intergral water proofing compound.

M&L for preparation of new plastered surfaces of walls and applying two coats of cement base paint over a coat of whitewash complete all as specified and directed.

M&L for preparation of newly plastered surface of wall and applying two coats of oil bound distemper over a coat of chalk whiting complete all as specified and directed.

M&L for preparation of newly plastered surface of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for complete removal of existing surface finishes by brushing, scrapping and water jetting and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed.

M&L for complete removal of existing surface finishes by brushing, scrapping and water jetting and applying two coats of oil bound distemper over a coat of chalk whiting complete all as specified and directed.

M&L for preparation of old painted surfaces of walls and applying one coat of cement base paint complete all as specified and directed.

M&L for preparation of old painted surfaces of walls and applying one coat of oil bound distemper complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

S&F figured glass 3mm thick, pin headed type and glazing with oil putty in square not exc 0.5 sqm in each pane complete all as specified and as directed.

S&F sheet glass 3mm thick, ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane complete all as specified and as directed.

M&L for preparation of new zinc (or galvanised) surfaces to receive painting by coating with mordant solution including washing and cleaning etc and applying two coats synthetic (red) roof paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel of any description, over 10 cm in width or girth, not otherwise described and applying a coat of red oxide primer complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M & L for preparation of new or previously untreated wooden surfaces of any description, not otherwise described, over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer on wooden surfaces complete all as specified and directed.

M&L for prepraration of old painted surfaces of steel of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

M & L for preparation of old painted wooden surfaces of any description, not otherwise described, over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparing of new wooden surfaces of any description and girth, not otherwise described and treated with a coat of creosote oil complete all as specified and directed.

Taking up or down 15mm dia of steel tubing and connections and removal from site complete all as specified and directed.

Taking up or down 20mm dia of steel tubing and connections and removal from site complete all as specified and directed.

Taking up or down 25mm dia of steel tubing and connections and removal from site complete all as specified and directed.

S&F GI tubing 15mm bore, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Ditto all as per Sl item No. 115.00 here-in-above but except material ( Note: Serviceable GI tubings obtained from dismantling under Sl item No 112.00 here-in-before shall be reused under the item)

S&F GI tubing 20mm bore, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Ditto all as per Sl item No. 117.00 here-in-above but except material ( Note: Serviceable GI tubings obtained from dismantling under Sl item No 113.00 here-in-before shall be reused under the item)

S&F 15mm bore unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe complete all as specified and directed.

S&F 20mm bore unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe complete all as specified and directed.

S&F 25mm bore unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe complete all as specified and directed.

S&F vitreous china squatting pan “Orissa pattern of size (580x440)mm white, with integral foot rests (excluding flushing cistern and flush pipe) but including lime concrete bedding complete all as specified and directed.

S&F in repairs vitreous china squatting pan “Orissa pattern of size (580x440)mm white, with integral foot rests (excluding flushing cistern and flush pipe) but including lime concrete bedding complete all as specified and directed.

S&F PVC low level flushing cistern, white, 10 ltrs capacity, valveless, syphonic action type including all fittings and flush pipe, PVC connection pipe 600mm long 15mm bore with brass heads and washers all as specified and directed.

S&F in repairs PVC low level flushing cistern, white, 10 ltrs capacity, valveless, syphonic action type including all fittings and flush pipe, PVC connection pipe 600mm long 15mm bore with brass heads and washers all as specified and directed.

S & F in repair wash basin, vitreous china (flat back or angle back type), white, (550 x 440) mm size, white, waste fittings, waste coupling, 32mm dia, waste pipe, complete all as specified and directed.

S&F pillar taps, ISI marked cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks for iron pipes for 15 mm bore dia of pipe and fixed complete all as specified and directed.

S&F in repairs pillar taps, ISI marked cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks for iron pipes for 15 mm bore dia of pipe and fixed complete all as specified and directed.

S & F in repairs bore bib taps, ISI marked cast copper alloy, chromium plated fancy type screwed down, screwed for iron pipe or for brass ferule for 15 mm bore dia of pipe complete all as specified and directed.

S&F in repairs stop valves ISI marked cast copper alloy, chromium plated, fancy type, with long shank and cup (concealed type) screwed down high pressure screwed both ends for iron pipe or unions for 15 mm bore dia of pipe complete all as specified and directed.

S&F angle valve ISI marked cast copper alloy, chromium plated, fancy type, screwed down high pressure screwed both ends for iron pipe or unions for 15 mm bore dia of pipe complete all as specified and directed.

S&F in repairs angle valve ISI marked cast copper alloy, chromium plated, fancy type, screwed down high pressure screwed both ends for iron pipe or unions for 15 mm bore dia of pipe complete all as specified and directed.

S&F in repairs Swivel shower of PTMT any colour for fixing with 15mm pipe. (Minimum weight 40gms) complete all as specified and directed.

S&F in repairs soap dish, vitreous China white, approximate size (160x 160x90)mm complete all as specified and directed.

S&F in repair CP brass health faucet with 1.00 m long PVC tube and wall hook. (Make: Jaquar Cat No ALD-IVY-583 or as per list approved makes enclosed hereinafter)

S&F in repairs brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed for 15 mm bore dia of pipe complete all as specified and directed.

S&F 32mm dia waste coupling of PTMTsuitable for urinal (half or full threaded) minimum weight - 45gms) complete all as specified and directed.

S&F grating square 150 mm size of PTMT (Minimum weight 100gms) complete all as specified and directed.

S&F in repairs brass chromium plated, 600mm long between flanges tubular towel rail , 20mm dia, D type. fixed with and including chromium plated brass screws and wooden plastic cleats, complete all as specified and directed.

S&F towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 190gms) complete all as specified and directed.

S&F in repairs harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as specified and directed

Dismantling water tanks capacity exc. 500 litres and n.exc. 1000 liters and removing to store complete all as specified and directed.

S&F rotational moulded polyethylene water storage tank, ISI marked, 1000 litres capacity of multilayered layer wall construction (Cylindrical, vertical with closed top) hoisted and fixed in position including all necessary inlet/outlet connections & brass ball valve complete all as specified in SSR Part-I and as directed.

S&F Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed to iron pipe of 20mm bore complete all as specified and directed.

S&F gun metal, globe or gate valves, ISI marked with iron wheel head, screwed both ends for iron pipe for 20 mm bore dia of pipe and fixed complete all as specified and directed.

S&F in repairs gun metal, globe or gate valves, ISI marked with iron wheel head, screwed both ends for iron pipe for 20 mm bore dia of pipe and fixed complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed.

S&F in repair stainless steel sink with drainage board 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm. (Make: Blue Star Model No BSSBSD-52 or equivalent in Jain Brothers / Prayag/ Cera)

S&F in repair stainless steel plate rack of size 24" x 36" x 10" complete all as specified and directed. (Make: Blue Star cat No KPR-312 or equivalent in Nirali/Jain Brothers/Prayag)

S&F 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints and fixed to wall as in waste/soil pipe complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints and fixed to wall as in waste/soil pipe complete all as specified and directed.

S&F 110mm bore PVC (SWR) reducer complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends with access door complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends complete all as specified and directed.

S&F 75mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F 110mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F 75mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F 75mm dia PVC (SWR) floor trap, plain with grating including setting and jointing with solvent cement complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete (1:2:4) type B-l smooth finished, and reforming benching as required, internal dia of pipe 150mm complete all as specified and directed.

Dismantling of galvanised plain/ corrugated including Nainital or similar pattern mild steel sheeting of any gauge, thickness roof coverings and segregating serviceable sheet and stacking for reuse and removing unserviceable materials from site of work complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and pavings not exc 15 cm thick thickness below or above ground level complete all as specified and directed.

Demolition of cement concrete (reinforced) in in any position not otherwise specifically provided for, below or above ground level complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and pre-cast concrete articles and removing unserviceable materials from site of work complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed.

Dismantling timber scantlings 40 sq. cm and over in section, in unframed work and in any position complete all as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as directed.

E/M work

Taking down carefully unserviceable aluminum/ copper point wiring (light/ fan/ socket/ power) complete including fixture & fitting such as switches, sockets, ceiling roses regulators, lamp holder etc. but excluding light fittings & fixture and exhaust fans etc removing and making good disturbed surfaces of wall/ceiling etc complete all as specified and directed.

Material and labour for point wiring surface type with two single core 1.5 Sq mm (nominal area) FRLS PVC insulated and unsheathed, multi-stranded, copper conductor cable in and including suitable size PVC casing capping with all fittings and fixing accessories and suitable size PVC box for mounting switches, regulator etc including multi-strand PVC insulated unsheathed stranded copper cable as earth continuity conductor of size 1.5 Sq mm and connecting to light fitting/fans etc complete all as specified and directed for following :- (Colour code to be followed)

One light/fan/bell point controlled by one, one way switch

One socket outlet 5 Amps 5 pin on independent board

One socket outlet 5 Amps 5 pin on same board with other switches

All as per item No. 174 here in before but with cable size 2.5 Sqmm and earth continuity conductor of 2.5 Sqmm size for one 5 pin 15 Amps socket out let on independent board complete all as specified and directed.

S&F modular switch piano, 6 Amps, single pole, one way complete all as specified and directed.

S&F modular switch piano, 16 Amps, single pole, one way complete all as specified and directed.

S&F modular socket outlet 2/3 Pin 6 Amps combined 2 module complete all as specified and directed.

S&F modular socket multipurpose 3 pin 16 Amps and 3 pin 6 Amps combined 2 module complete all as specified and directed.

S&F Ceiling rose, 3 phase/ PVC/ polycarbonate, isolated body complete all as specified and directed.

S&F Modular Bell push 6A 1 module complete all as specified and directed.

S&F Buzzer, Ding Dong AC. 230 volts, single pole complete all as specified and directed.

S&F modular white cover with frame for fixing of 1 module.

S&F modular white cover with frame for fixing of 2 module.

S&F modular white cover with frame for fixing of 3 module.

S&F modular white cover with frame for fixing of 4 module.

S&F modular white cover with frame for fixing of 8 module.

S&F modular white cover with frame for fixing of 12 module.

S&F blank spacer plate for single module.

S&F modular electronic fan regulator rotary stepped type 120W, 240V, single phase, two module and connecting up complete all as specified and directed.

Taking down old unserviceable main switch/ DBs/ MCB DBs with MCB including making good the disturbed surface complete as directed.

S&F sheet metal enclosure for MCB’s distribution board, 240 Volts, 8 ways single pole and neutral including 200 Amps rated busbar, neutral link, din rail double door verticle for breaking capacity 10 KA complete all as specified and directed. (Make: Havells cat part No. DHDPSHODRW 08 or as per list approved makes enclosed hereinafter)

S&F sheet metal enclosure for MCB’s distribution board, 240 Volts, 4 ways single pole and neutral including 200 Amps rated busbar, neutral link, din rail double door verticle for breaking capacity 10 KA complete all as specified and directed. (Make: Havells cat part No. DHDPSHODRW 04 or as per list approved makes enclosed hereinafter)

S&F MCB single pole and neutral 06 to 32 Amps, ‘C’ series 240 Volts, breaking capacity 10KA complete all as specified and directed.

S&F MCB single pole 06 to 32 Amps, ‘C’ series 240 Volts, breaking capacity 10KA complete all as specified and directed.

S&F PVC Board (30 x 25 x 5) cm depth medium quality ISI marked complete all as directed.

Taking down old unserviceable light fitting of any type and in any situation complete all as directed.

S&F universal batten for G13 T8 lamps (LED TUBE),1200mm long complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable complete all as specified and directed. (Make: Havells Regal Batten Cat No.REGALBATTENT8UPTO1X22WSSBSWH or equivalent in Philips/ Bajaj/ Crompton)

S&F ultra bright LED polycarbonate tublight 20W, 1213mm long with very high efficacy suited for installation T8 tublight with G13 lamp holders, complete with all accessories complete all as specified and directed. (Make: Photon Ultra LED tublight Havells Cat No.PHOTONULTRA1213T8SSTL20WLED865SPCor equivalent in Philips/Bajaj/CG)

S&F wall mounted decorative light fixture made up of polycarbonate suitable for and including 10W CFL/LED lamp complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable complete all as specified and directed. (Make: Philips Nova B22/1X10W LED/ Havells/Bajaj/CG)

M&L for Lamp holder, PVC/Polycarbonate type with cord grip cap suitable for pendent/Angle type including one 10W LED complete all as specified and directed.

S&F wall mounted LED batten with polycarbonate hosing & integrated electronc driver, 9W, 600mm long with all accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable complete all as specified and directed. (Make: Havells E-Lite LED Pride Plus Cat No.LXEXBLP7IN1W009 or equivalent in Philips/ Bajaj/ Crompton)

S&F building security light fitting new generation energy saving & environmental friendly long life versatile pressure die cast aluminium IP-66 high power LED light 20 watt including suitable size of wall bracket and connecting up with twin core twisted flexible copper conductor cable complete all as specified and directed. (Make: Havells Endura Pearl Cat No. ENDURAPEARLSL20WLED757SASYTOPC or equivalent in Bajaj/Philips/Crompton)

Taking down old unserviceable sub main wiring including batten/suspending wires complete all as directed.

M & L for sub main wiring with 2 single core 6.0 Sqmm PVC FRLS insulated unsheathed cable multi-stranded copper conductor drawn through and including PVC casing/capping of suitable size with all fittings and fixing accessories on roof, walls, ceiling etc. including 6.0 Sqmm PVC insulated unsheathed one core multistranded copper conductor earth wire complete all as specified and directed. (Note: Two run of single core cable and one run earth wire will be measured as one length)

Taking down old unserviceable service cable including batten/suspending wires complete all as directed.

S&F Service wire PVC insulated and PVC sheathed stranded Aluminium conductor 10 sq mm 2 Core fixed to walls or suspended by insulating hanger not more than one meter apart including 4mm dia GI suspension wire and binding with 2mm dia new GI wire with reel insulator complete all as directed.

Taking down ceiling/exhaust fan including dismantling all necessary electrical connections to facilitate repairs to ceiling/wall complete all as directed.

Hanging only/ Refixing ceiling/exhaust fan removed under item Srl No 208 above and connecting up including provision of cable from ceiling rose or connector to fan complete all as directed.

Earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level connected to galvanized earth wire 4mm dia by means of galvanized iron or steel bolts nuts check nuts and washers and other end connected with earthing testing point including providing suitable testing points as directed including funnel, watering pipe of 20mm bore, light grade galvanized iron pipe, wire mesh charcoal of coal dust and common salt in alternative layer all around the earth electrode compacted thickness 15cm with concrete pit in PCC 1:3:6 type C1 50mm thick pre cast RCC 1:2:4 type B1 cover slab set in CM (1:4) re-enforcement with 8mm dia deformed bars @ 15cm C/C and suitable handle of 10mm dia MS round bars, including earth work in hard/dense soil as required complete all as shown in electrical plate No 3 of MES Schedule Part I and testing on completion all as specified and as directed.

L BINOD CONSTRUCTION CO

MANI PRASAD GUPTA

M/s SSS Motors

M/S N JADUMANI SINGH