8698/GWL/E8 REPAIR TO ROOF, FALSE CEILING, SUNKEN FLOOR OF TOILETS, CHAJJAS AND IMPROVEMENT OF MD / OTM ACCN ETC IN THE AREA OF AGE B/R-II UNDER GE GWALIOR

Amount

Demolition of cement concrete of any description and in any position (unreinforced) in ground floors and paving not exceeding 15 cm thick (below or above GL) complete all as specified and directed.

M&L for 10 mm thick rendering in CM (1:4) over roof ,surface finished even and Smooth mixed with water proofing compond complete all as speceified and as directed by engineer- in charge . Note : Water proofing compound shall be measured and paid separately under appropriate item of BOQ as "supply only "

M &L in repairs For applying water proofing treatment with the following coats :- (a) First coat of bitumen primer conforming to IS -3384 @ 0.3 Kg/sqm (b) Second Layer of APP based polymectric membrane minimum weighing 3kg /sqm and minimum 3 mm thick reinforced with polyster non woven fabric land on primed surface by torch application (c) third one coat of aluminium bituminous paint over polymetric membrane complete all as specified and as directed.

M &L For applying water proofing treatment with the following coats :- (a) First coat of bitumen primer conforming to IS -3384 @ 0.3 Kg/sqm (b) Second Layer of APP based polymectric membrane minimum weighing 3kg /sqm and minimum 3 mm thick reinforced with polyster non woven fabric (wt. not less than 150 gms /sqm ) land on primed surface by torch application complete all as specified and as directed.

Supply only Liquid water proofing compound complete.

M & L for cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and as directed.

M&L, precast cement concrete tiles of size 250mm x 250mm x 20 to 22 mm as in foor top ,confirming to IS-1237 laid over 15 mm thick screed bed in CM 1:4 and set, jointed and pointed in neat cement slurry in floors, and cut & plished between tiles 2 to 3 mm will be filled with cement mortar (1:2) by mixing of chemical or equilant approved by the GE etc complete all as specified and as directed.

M & L PCC (1:2:4) Type Bo using 12.5 mm graded stone aggregate as levelling course/mass concrete complete all as spd and directed.

M & L PCC (1:2:4) Type Bo using 12.5 mm graded stone aggregate pan, cills, steps; seismic and other similar bands,plinth courses, string courses,lacing courses, parapets and railings upto 60 cm in height,copings, kneelers, apex stones, bed plates, kerbs not provided for in water troughs and the like including weathering, slightly rounded or chamfered angle complete all as spd and directed.

Demolition of wall and ceiling boards fibre pulp insulation etc or insulation boards/slabs/blankets any thickness including cover fillets, complete all as specified and directed.

S&Fof False ceiling 4 mm thick HPSC pre-prime non asbestos fibre cement building board (E-classic size 600mm x 600 mm/ 595 mm x595 mm ) decorative finish fixed with clips and screw including powder coated galvanised MS grid frame work false ceiling of ( Main Tee size 32mmx24mmx0.65mm cross tee 24mmx24mmx0.45mm ) and with slot for fixing including suspended with 2mm dia. GI wire hangers fixed with steel dash through fasteners from purline of the roof complete all as specified and as directed

S&F In Repairs for E- grid false ceiling 4 mm thick HPSC pre-prime non asbestos fibre cement building board (E-classic size 600mm x 600 mm / 595mm x 595 mm) decorative finish and fixed with from purline of the roof, complete all as specified and directed.

S&F, in repair 4 mm thick asbestos cement plain building board fixed to timber frame work/iron frame on ceiling surface complete all as specified & directed

M&L, applying three coats of white wash to ceiling including preparation of surfaces i.e (A C Board) complete all as specified and as directed.

S&F, in repair, 2nd class hard wood, plain fillets, square, rectangular or triangular in section clean sawn secured with nails or brads sectional area not exc 3 Sqcm, complete all as specified and as directed.

Cutting holes in brick walls built in cement mortar for inserting hold fast etc and making good the disturbed portion in CM 1:3 or cement concrete 1:2:4 type B1, depth as required, depth exc half brick but not exc one brick wall complete all as specified and as directed.

Dismantling of AC (corrugated / semi-corrugated) sheets in roof covering including any type of ridges complete all as specified and as directed.

S&F Pre painted galvalum sheet 0.50 mm thick having aluminum zinc coating 150 gsm/ sqm steel sheet any colour having tensile strength of 550 Mpa as in Roof covering /cladding to wall fixed with self tapping screws complete all as directed

S&F Pre painted galvalum sheet 0.50 mm thick having aluminum zinc coating 150 gsm/ sqm double ribbed trapezoidal profile plain steel sheet any colour having tensile strength of 550 Mpa as in Roof covering /cladding (ridge) to wall fixed with self tapping screws complete all as directed .

M&L Hand rails, half round or other stock section or core for wooden hand rail straight portion , drilled and counter sunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing post including cutting tops to shape as directed, drilling holes, notching for wire , etc.; flat iron fillets ( for securing wire mesh etc. including all necessary drilling , bolting or rivetting , etc., and similar work conforming to Fe 290 Gde E 165 with and including applying two coats of synthetic enamel paint over a coat of primer alround before fixing in position complete all as specified and directed

Dismantling of wrought iron or mild steel work of any description not other wise provided for complete all as specified and as directed.

Dismantling of timber in fillets, rails, posts, rafters, purlins etc under 40 Sq. cm provided for complete all as specified and as directed.

S&F rolled section as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates confirming to Fe-290 ( Gde E-165) complete all as specified and directed

M&L for applying two coat of synthetic enamel paint as one coat including Preparation of new Steel surface over 10 cm width or girth comlete all as specified and directed .

M&L two coat of synthetic enamel paint over coat of Red oxide primer over new steel surfaces nexc 10 cm width or girth complete.

M&L two coat of synthetic enamel paint over coat of Red oxide primer over old steel surfaces nexc 10 cm width or girth complete.

S&F Framed brackets of angles or tees with web and flanges cut to shape, drilled and counter shunk for screw, including bending and welding angle necessary gusset plate riveting etc n exc. 10 kg each brackets confirming to Fe-290 Gde E-165 complete all as specified and directed.

S&F for framed work such as grills gratings, etc, with ends of bars shouldered and or riveted , or forged into spikes, framed guard bars , barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe 290,E-165 , complete all as specified and directed.

Demolition of brick work /stone work built in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed.

M&L for Brick work with sub class B bricks straight or curved on plan exc. 6m mean radius built in cement mortar (1:6).complete all as specified and as directed.

M& L for Brick work with sub-class `B' bricks, straight or curved on plan to any radius, in half brick work built in cement mortar 1:4 complete all as specified and as directed.

Taking down cement or cement lime plaster on brick or stone walls etc. including racking out joints hacking for key scrubbing down with water etc.complete.

M&L for 15 mm thick rendering in cement mortar (1:4) on brick or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for15 mm thick rendering in cement mortar (1:6) on brick or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 5 mm thick in Cement Mortar (1:3) on ceiling finished even and smooth without using extra cement complete all as specified and directed.

Dubbing coat with cement plaster 1:4 in cement mortar average 15mm thick on irregular face of wall/ concrete complete all as specified and directed

Supply only water proofing compound (ISI Mark)

M&L for preparation of the newly plastered surfaces of walls & applying three coats of white wash on wall surfaces complete all as specified and directed.

M&L for preparation of the newly plastered surfaces of ceiling & applying 3 coats of white wash on ceiling surfaces complete all as specified and directed.

Taking up or down steel tubing and connetion including cleaning for refixing or removing to store of 15mm bore of pipe, complete all as specified and directed.

Taking up or down steel tubing and connetion including cleaning for refixing or removing to store of 20mm bore of pipe, complete all as specified and directed.

Taking up or down steel tubing and connection including cleaning for refixing or removing to store of 25mm bore of pipe, complete all as specified and directed.

supply and laying 20 mm dia .of bore CPVC pipe SDR11 and Plain CPVC SDR11 fittings (ISI ) marked ,concealed or fixed to wall or laid in floors complete all as specified and as directed

supply and laying 25 mm dia .of bore CPVC pipe SDR11 and Plain CPVC SDR11 fittings (ISI ) marked ,concealed or fixed to wall or laid in floors complete all as specified and as directed

S & F 20 mm dia steel tubing and connection galvanized with all fittings medium grade tube in floors, walls and ceiling etc

S & F 25mm dia steel tubing and connection galvanized with all fittings medium grade tube in floors, walls and ceiling etc

Taking down eaves gutters and rain water pipes (any size 75mm to 110mm of any pattern) ,of any description and in any position, including all fittings , heads, shoes, bends, swan necks, etc., (measured overall as fixed along the centre line over fittings and accessories)complete all as specified.

S&F for 110mm dia PVC(SWR) pipes single socketed, in any length with rubber ring joints,fixed to walls complete all specified.

S&F for 75 mm dia PVC(SWR) pipes single socketed, in any length with rubber ring joints,fixed to walls. complete all as specified .

S&F for 75 mm dia PVC(SWR) pipes single socketed, in any length with rubber ring joints,laid in trenches or in floors complete all as specified .

S&F for 110mm dia PVC(SWR)pipes bends any radious \ complete all as specified and directed.

S&F for 75 mm dia PVC(SWR)pipes bends any radious. complete, complete all as specified and directed.

S&F for 110mm dia PVC(SWR)pipes junction,single (single T/Y ) equal or unequal any radious.with acces door, complete all as specified and directed.

S&F for 110mm dia PVC(SWR) vent cowl, complete all as specified and directed.

M&L for 75 mm dia of out let PVC (SWR) floor trap plain with CP grating including jointing with solvent cement as in repair complete all specified.

M&L for PVC (SWR) gully trap 125 /100 plain with grating incl. jointing with solvent cement as in repair, complete all as specified and directed.

Disconnecting existing water tanks, setting aside (or lowering if required) for repairs, cleaning etc and reconnecting and refixing in position capacity of tank exc 500 and n.exc 1000 ltr. (cleaning, repairing etc measured separately)

Cleaning and removing all scale and dirt etc. from tanks and from mouths of circulating pipes etc capacity of tank exc 250 ltrs but n.exc 500 Ltrs complete all as specified and as directed.

Dismantling water tanks of any description and in any position , of capacity exceeding 250 litres but not exceeding 500 litres complete all as specified and directed.

Dismantling water tanks of any description and in any position , of capacity exceeding 500 litres but not exceeding 1000 litres complete all as specified and directed.

S & F Rotational moulded poly-ethylene multilayer water storage tanks (cylinderical vertical with closed top) 500 litres capacity, triplr layer in construction white in colour hoisted and fixed in positioncomplete all as specified and directed.

S & F Rotational moulded poly-ethylene multilayer water storage tanks (cylinderical vertical with closed top) 1000 litres capacity, triplr layer in construction white in colour hoisted and fixed in position complete all as specified and directed.

S&F for 20mm ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 20 m m - 210 gms / 25mm-455gms/ 40mm - 690 gms) complete all as specified and directed.

S&F for as in repair 20 mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed 20mm dia of pipe . (Minimum weight 20mm-210gms. ) complete all as specified and directed.

S&F for in repair gun metal globe valve with iron wheel head screwed both ends for iron pipe of 20mm bore, complete all as specified and directed.

S&F for in repair gun metal globe valve with iron wheel head screwed both ends for iron pipe of 25mm bore, complete all as specified and directed.

M&L for vitreous china squatting pan, orissa pattern sise 580x440mm white with integral foot rest (excluding flushing cistern) including vitreous china ‘P’ or ‘S’ traps connection to trap and to flushing pipe to complete fixed in repairs and making good to floor, complete all as specified and directed.

S&F for in repairs of vitreous china wash basin, white, flat back, size 550 x 400mm Including waste coupling ,waste pipe and labour for fixing pillar tap ,pvc connection but including cutting for and pinning in ends of and including brackets complete all as specified and directed. Note : Pillar tap and PVC connection will be measured paid separetly.

S&F for as in repair viterous china wash down water closet pan (pedestal pattern) white excluding fixing bolts,flushing cistern and flush pipe including connection to drain and to flushing pipe syphonage pipe etc and mild steel chromium plated or aluminised hinges device & on CP Jet complete all as specified and directed.

S&F for in repair PVC valveless syphonic action type flushing cistern low level white with inlet ball valve,float end handle handle including bracket complete of capacity 10 litres, complete all as specified and directed.

Supply only 15mm dia PVC connection with PTMT nuts of length 450 mm, complete all as specified and directed.

S&F for in repairs Soap dish of CP fixed with pvc rawal plugs and screw, complete all as specified and directed.

S&F for in repair CP tubular towel rail D type 20mm dia and 60cm long complete all as specified and directed.

S&F for peg set of six S.S. fixed to wall with PVC plugs and screw, complete all as specified and directed.

S&F for in repairs Brass CP WHB mixer for mixing hot & cold water screwed down for 15mm bore iron pipe complete all as specified.

S&F in repair Health faucet with 1.00 metre tube ( Branded tube ) including flexible pipe and brass chromium plated nuts completed all as specfied and directed.

S&F for in repairs vitreous china urinals, Half stall type ,white with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement complete all as specified and directed.

S&F for in repairs15mm,pillar taps fancy type long body chromium plated,cast copper alloy, with brass ceramic disc spindle and capston heads,scewed down high pressure, with or without lettered 'hot' or Cold' with long srewed shanks and flynuts, srewed for iron pipe complete all as specified .

S&F for in repairs 15mm angle cock chromium plated,cast copper alloy, with brass ceramic disc spindle and capston heads,scewed down high pressure, with or without lettered 'hot' or Cold' with long srewed shanks and flynuts, srewed for iron pipe fixed and complete all as specified.

S&F for 15mm ,bib tap Fancy type long body chromium plated,cast copper alloy, with brass ceramic disc spindle and capston heads,scewed down high pressure, with or without lettered 'hot' or Cold' with long srewed shanks and flynuts, srewed for iron pipe fixed in repair and complete all as specified.

S&F for shower rose brass chromium plated without swivel joints, 100 mm in size including fixing to steel pipe complete all as specified and directed fixed in repairs, complete all as specified and directed.

S&F for in repairs for 15 mm Stop valve cast copper alloy screwed down high pressure with CAPSTON HEAD handle chromium plated with long shank and cup (concealed type) screwed both ends for iron pipe 15mm bore or for unions complete all as specified and directed.

S&F in repairs for wall mixer with Two in one pattern in of brass CP, complete all as specified and directed.

S&F in reapir plastic water closet seat covered white coloured closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging devise complete all as specified and directed.

S&F for in repairs PVC Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms/20mm125gms complete all as specified .

S&F for in repairs mild steel Chromium plated grating 100 mm dia, fixed in repair, complete all as specified and directed.

Dismantling floor, hearth or wall tiling of any description and in any position including cement mortar bedding (but not backing) complete all as specified and directed.

M&L for digital glazed ceramic tiles, coloured tiles 300mm x 450mm x 7mm thick on vertical faces ie. as in skirting/dado etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles fix over and including 10 mm thick backing coat in cement mortar (1:4) complete all as specified and directed.

M&L for Joint free ceramic tiles, coloured tiles 300mm x 200mm x 7mm thick on vertical faces ie. as in skirting/dado etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles fix over and including 10 mm thick backing coat in cement mortar (1:3) complete all as specified and directed.

M&L for non skid ceramic Coloured tiles, 300mmx300mmx 6 mm to 7mm thick, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match with the colour of tiles, over and including 15 mm thick screed bed or bedding layer of cement mortar( 1:6) complete all as specified and directed.

M&L Plain cement concrete (1:5:10) type D2 (using 40 mm graded stone aggregate) as in foundations / mass concrete complete all as specified.

M&L for providing two coats of water proof coating complete all as specified and directed.

S&F in repair 5mm thick PVC sheet fillet of width 35mm for wall panelling (At the spacing of 1 feet centre to centre) inclusive of fixing on to wall to make PVC Frame as per secification and drawing comlplete all as specified and directed.

S&F in repair Solid PVC Wall Lining consisting of 5mm thick Plain wood grain printed PVC sheet inclusive of solvent cement and fixing at site on to wall to make PVC Frame as per specification and drawing comlplete all as specified and directed.

S&F 12mm thick tuffended designer glass fixed on steel pivot all as approved sample with engravings/ designs/ symbols to the pattern and style as approved and directed by Engineer-in-Charge.

S&F 'D' type stanless steel handle decorative type 300mm long bright finished all as per design/ pattern approved by Engineer-in-Charge

Taking down chowkhat or frame (without taking off shutter from the frame) not exceeding 1.5 Square Metre each , removing from the site Cutting holes exc 150 Sq.cm but n.exc 400 Sq.cm in super facia area into or through brick walls built in mud mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required complete all as specified and as directed.

Taking down chowkhat or frame (without taking off shutter from the frame) exceeding 1.5 sqm and not exc 4.00 sqm each , removing from the site Cutting holes exc 150 Sq.cm but n.exc 400 Sq.cm in super facia area into or through brick walls built in mud mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required complete all as specified and as directed.

Taking down shutter of any description exc 1 Sqm and not exc 2 Sqm each complete all as specified and as directed.

M&L for 2nd class hardwood palin, solid, straight chowkhat and frames wrought frame rebated on solid rounded and chamfere put together with glue pinned at joints complete all as specified and directed

S&F galvanised wire cloth, .0.48mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised staples complete all as specified and directed

S&F 35 mm thick Flush shutters ,soild core construction ,with paticle board core and plywood face panels , commercial type if both face is covered with decorative face veneer with lipping /frame to match and complete all as specified and directed.

M&L preperation of new wooden surface and applying two coat of synthetic enamel paint over a coat of pink primer on new wooden surface any description not otherwise described over 10 cm width or girth and complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue ,anodised with hard drawn steel spring,150mm long, fixed in floor .

S&F MS 150 mm ordinary rat tail springs plate type incl.rollar plate etc.

Supply & Fixing solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube fixed in opening as per specification & drawings complete all as specified and as directed.

S &F for factory made solid panel PVC door shutter 30mm thick ( style) consisting to frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Penelling of plain colour PVC sheet to be fitted in the MS. frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. complete all as specified and as directed.

All as per above but above but fully glazed/glass panes used instead of 5mm thick single side prelam PVC sheet panels complete.

S&F 100 mm long size aluminium alloy anodised hinges medium weight complete all as specified and directed by Engr-in-Charge.

S&F 150 mm long aluminium anodised , barrel tower bolt of extruded section and fixed complete all as specified and directed.

S&F aluminum handles cast type, anodized of 150 mm size complete all as specified and directed.

S&F butt hinges 100mm long medium weight, cold rolled mild steel.

S&F 3mm thick,ordinary glass pin head type and glazing with oil putty,silicone or wooden beads, in square not exceeding 0.5 sqm in each pane including hacking out old broken glass of any thickness and any description from wooden/ steel frame/ stone,concrete or brick surrounds complete all as specified and directed.

S&F in repair galvanised wire cloth, 0.48 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised staples complete all as specified and directed

S&F Aluminium alloy, anodised, sliding door bolt 250mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

M & L for Powder coated (minimum thickness of powder coating 50 micron) aluminium frame for doors , windows , ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

M & L for Powder coated (minimum thickness of powder coating 50 micron) aluminium door shutters of aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, rubber neoprene packing, powder coated aluminium handles 150mm size 2 Nos, 3 Nos powder coated aluminium hinges heavy duty and 02 Nos 150mm long powder coated aluminium tower bolts in each door shutter with powder coated aluminum snap beading, screws etc. complete all as specified and directed Note : Panel filling ie. glass, fibre sheet, board etc. shall be measure and paid for separately.

M & L for Powder coated (minimum thickness of powder coating 50 micron) aluminium window and ventilator (adequate track) without sash, aluminium section weighing 0.55 kg/m including joining cleats, glazing clips, rubber neoprene packing, necessary powder coated hardware ie. handles, barrel tower bolts, hinges etc, powder coated aluminum snap beading, screws etc. complete all as specified and directed Note : Panel filling ie. glass, fibre sheet, board, wire mesh etc. shall be measured and paid for separately.

S&F for 12 mm thick prelaminated particle board exterior grade prelamilated one side with decorative choice lamination and other side balancing white lamination fixed with screws complete all as specified .

S & F for door closer hydraulically regulated, designation No. 3, universal type, aluminium die-cast body (ISI Marked), suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed in repair complete all as specified and directed

S & F of double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed in repair complete all as specified and directed

Dismantling boarding any description fixed with nails in any position (including cup board shutter/shelve upto 25mm thick) complete.

S&F for 18 mm thick PVC Celuka ply of both side prelaminated and other side plain white colour fixed with screws ,solvent cement /adehesive to make kitchen cabinet partion ,shelves ,shutter, drawer complete all as specified .

S&F for 12 mm thick PVC Celuka ply of both side prelaminated and other side plain white colour fixed with screws ,solvent cement /adehesive to make kitchen cabinet partion ,shelves ,shutter, drawer complete all as specified .

S&F for aluminium anodised barrel tower bolts of extruded section of 100mm size, complete all as specified and directed.

S&F for continuous (piano) hinges mild steel bright finish or electro galvanised width of width of flaps nexc 30 mm (when open), complete all as specified and directed.

S&F for extruded aluminium alloy handle of 100 mm size fabricated type, anodised.complete all as specified .

S&F for Haps and staple safety type Aluminium anodised with MS hinge pin including bolt to hinge pin of 100 mm size sixed with screw complete all as specified .

S&F for magnate catcher of metal body and striking plate heavy duty includind fixed with screw, complete all as specified and directed.

S&F in repairs 25mm dia stainless steel curtain rod not less than 0.80mm thick including fixing of sufficient brackets ( minium 2 nos at every 1.50m length) complete all as specified and directed

S&F End Knob 25mm dia stainless steel for curtain rod complete all as secified and directed

Babatia super works

RAJ AND BROTHERS

M/s Himgiri construction

M/S YOGANSH CONSTRUCTION CO.

M/s Ratan Lal Jain and Co.

mahamaya constructions

M/S SANJAY AGARWAL