Supply, Testing, Installation andCommissioning and Demonstration of Tools and Equipment for Solar Technician (Electrical) and Pneumatic and Hydraulic for Fitter Trade at Govt. Industrial Training Institute, Jhargram

Solar Technician (Electrical) and Pneumatic and Hydraulic for Fitter Trade

Measuring Steel Tape, 5 meter

Combination Plier Insulated, 200 mm

Screw Driver Insulated, 4mm X 150 mm, Diamond Head

Screw Driver Insulated, 6mm X 150 mm

Electrician screw driver thin stem insulated handle, 4mm X 100 mm

Heavy Duty Screw Driver insulated, 5mm X 200 mm

Electrician Screw Driver thin stem insulated handle, 4mm X 250 mm

Punch Centre, 9mm X 150 mm

Knife Double Bladed Electrician, 100 mm

Neon Tester, 500 V

Steel Rule Graduated both in Metric and English Unit, 300 mm with precision of 1/4th mm

Hammer, cross peen with handle, 250 grams

Electrical Symbol and Accessories Charts, as per NIMI Standard

Pipe vice Cast Iron with hardened jaw open type, 100 mm

Hand Vice, 50 mm jaw

Table Vice, 100 mm jaw

Hacksaw frame (with blade), Adjustable 300 mm Fixed 150 mm

File flat, 200 mm 2nd cut with handle

File half round, 200 mm 2nd cut with handle

File round, 200 mm 2nd cut with handle

Pliers long nose insulated, 150 mm

Pliers flat nose insulated, 200 mm

Pliers, round nose insulated, 100 mm

D.E. metric Spanner Double Ended, 6 - 32 mm

Gauge, wire imperial stainlees steel marked in SWG & mm, Wire Gauge - Metric

Portable Electric Drill Machine, 0-12 mm capacity 750W, 240V with chuck & key and twist drill bit (2,3,4,5,6, 10mm)

Crimping Tool, 1.5 sq mm to 16 sq mm 16 sq mm to 95 sq mm

Pliers Side Cutting, 150 mm

Wire stripper adjustable length, 200mm ,stripping capacity ( 0.2 - 6.0 sq mm)

Hammer, ball peen With handle, 250 grams

Scriber (Knurled centre position ), 200mm

Tool kit Box/bag portable, L- 450mm, W- 200mm, H - 155mm

Allen Key, 9 pcs per set, ( 1.5,2.5,3,4,5,6,8,10 mm)

Scissors blade, 150 mm

Electrical loads: set of Incandescent lamp, Tube light, CFL, LED light, Heater and Geyser, Electrical loads: set of Incandescent lamp, Tube light, CFL, LED light, Heater and Geyser

Torque wrench, 8N-m to 15N-m

Pipe Cutter to cut pipes, upto 5 cm. dia

Pipe Cutter to cut pipes, above 5 cm dia

Try Square, 150 mm blade

Multi Meter (analog), 0 to 1000 M Ohms, 2V to 500 V,100 microA to 10A DC and AC

Load Bank (variable), Up to 1.2 KW ( Lamp / heater Type)

Wire Cutter and Stripper, 150 mm

Earth Plate, 60cm X 60cm X 3.15mm Copper Plate 60cm X 60cm X 6mm GI Plate

Earth Electrode, Primary Electrode 2100x 28x 3.25 mm Secondary Cu Strip 20x5mm

Out Side Micrometer, 0 - 25 mm least count 0.01 mm

Tap set, Different size

Trolley for Transportation of Batteries, Stanley foldable steel platform trolley 150 Kg

Die for Threading, Different sizes

Rooftop Mounting Structure, For 4 x 250 W solar panels mounting practice, with tilt adjustment

Electrical wiring and switch gear rack, Electrical control elements suitable for practice of control circuits using banana plugs and sockets

Protective relays and contactors rack, suitable for practice of control circuits using banana plugs and sockets

MCCB, 100Amps, Triple pole

ELCB and RCCB, 25Amps, double pole and 25Amps, double pole, IΔn 30 mA

Fuses, HRC, Glass, Rewire Type

Civil work utensils, 1. spade, 2. mixing spoon, 3. leveling plates

Plumbing tools, The plumbing Tools List 1.Pipe wrench, 2. Basin wrench, 3. Adjustable wrench, 4. Faucetkey pipe work, 5. Hacksaw, 6. Tube and Plastic pipe cutters, 7. Plumberr's torch, 8. Thread sealing tape, 9. Pliers, 10. Press fitting systems, 11. Goggles, 12. Gloves, 13. Heat shields / pads, 14. PEX pipe expender & fittings,

Multimeter, Digital 0 to 1000 M Ohms, 2V to 700 V,100 microA to 10A DC and AC

Megger, Analog - 500 V, Digital -500V

Hydrometer, specific gravity range 1000 - 1500

Solar Insulation meter, 5 KV, Digital, Insulation Resistance- (0.1M to 200G) Ohm

Pyranometer, 0 - 90 degree tilt at 1000 W/sq.m beam irradiance

Pyrheliometer, ISO:9060 First Class MS - 57, Spectral range: 200 to 4000nm, Irradiance range: 0 - 4000 W/m² Temperature range: -40 to +80° C

Lux meter, Lux meter LCD read out 0.05 to 7000 Lumens with Battery

Magnetic Flux Meter, 0-500 tesla

Tong Tester / Clamp Meter, 0 - 100 A (Digital Type)

Soldering Iron, 25 Watt, 65 Watt and 120 Watt, 230 Volt

Temperature controlled Soldering Iron, 50 Watt, 230 Volt

Thermometer Digital, 0° C - 150° C

Sun Shine recorder, (1604) Sunshine recorder In northern and southern equatorial zones between 25...60°

Solar cell based sunlight radiation meter, For Solar power measurement up to 2000 w/square meter

Magnetic compass, Output Power : 10 Watts (approximate). Range : 0 to 300 meters.

Cut models of photo voltaic cell assembly, Mono crystalline module, Amorphous silicon module, Thin film module, Poly crystalline module

Cut model of Lead acid battery, Cut model of Lead acid battery

Lead Acid battery, 12V, 40Ah, 75Ah

Lead Acid battery, 12V, 100 Ah

Solar simulator for solar cell characteristic study, To study IV curve of a solar cell of minimum 2 watt under variable illumination, temperature and suitable load

IV Curve tester, 1500V IV Curve Tester - 500W, Detection of I-V curve on PV modules and strings: 1500V/10A - 1000V/15A Quick IVCK test for measuring Voc and Isc on PV modules and strings VOC 1500V / ISC 15A

Weather monitoring station, To monitor and record Sunshine, wind velocity, temperature, rainfall etc with software.

Solar Grid tied inverter Demonstrator kit, 3KW Solar Grid TIE Inverter

Solar, wind and hybrid power plant, 1 KW cumulative

Solar Street Light, 12V, 75Ah battery, 75 Wp solar panel, 12V, 10A dusk to dawn charge controller, 60 W LED lights and 9 m height pole all dismountable

solar DC pump, 1 HP with full assembly i.e, Solar Panel, Controller, electrical protections, accessories etc.

Sun path finder, Sun pathfinder, Highly polished, transparent, convex plastic dome to give a panoramic view of the entire site

Solar energy trainer with grouping of solar cells, To group (series or parallel) at least six solar cells each with minimum 2 W with suitable loads

Solar tracker demonstrator kit, To study manual and automatic control of 10 W solar panel in East- west and North-south &back

Solar PV e-learning software using animations for training, Solar PV e-learning software using animations for training

Halogen lamp with stand for illumination of solar panels in lab, AC mains operated to provide 0 to 1000 watts per meter square

Motorized Bench Grinder, AC mains operated Heavy Duty 6 inch 0.5 HP Single Phase Bench Grinder, 2800 Rpm, 0.37 Kw

Battery Charger, 0 - 6 - 9 - 12 - 24 - 48 V, 30amp

Solar photovoltaic module, 75 W mono crystalline module, 75 W amorphous silicon module, 250 W thin film module, 5W, 10W, 40W poly crystalline module

Solar panels, 250 WP Poly Crystalline Solar Panel

Solar Charge controller with Dusk to Dawn automatic switching, 10 Amp 12V Solar Charge Controller, D2D, Auto ON/OFF at Night/Day‎ PWM , Micro controlle based design

Solar charge controller with manual switch ( Day lighting), 10 Amp 12V Solar Charge Controller with manual switch (Day lighting)

Array junction box, For connecting 250W x 4 Nos. solar panel with DC fuse, DC MCB, and surge suppressor protection

Solar lantern, LED type

Solar lantern, CFL type

Solar lantern assembly sets, Compact Fluorescent /LED Lamp of 5/7W in 4 pins and has SPV module features, Type of Product : Solar CFL Lantern Body Material : ABS Type of Battery : SMF Battery Capacity(Ah) : 7 Ah SPV Module : 8 Wp

Home light system, 12 V DC with FM receiver, LED bulb and mobile charger as loads

Solar cell kit, To demonstrate the effects of conversion of Solar light into electricity. The apparatus consists of : * Moving coil meters fitted on box * Lamp house with power supply * Solar cell mounted * Connection leads * Fan is connected * LED is connected Luminous 160 Watt - 12V Poly Crystalline Solar Panel.

Clinometer, for Angle measurement Accuracy 2.0 mm Size 50 mm to 2000 mm

Spirit level, For floor level check accuracy depends on its sensitivity. ... 2 mm (0.079 in)

Anemometer, The wind sensor is measuring velocities up to 40 m/s and wind directions over a range from 2.5 º - 357.5 º

DC table fan, 12 V

A.C. Voltmeter M.I, 0 –500V AC

Volt meter, 0 - 30V

Volt meter, 0 - 100V

Ammeter MC, 0 - 1A

Ammeter MC, 0 - 5A

Ammeter MCcentre zero, 0 - 20A

Ammeter MCcentre zero, 0-50A

Power Factor Meter, single phase digital type

Rheostat, 0 -1 Ohm, 5 Amp, 0 -10 Ohm, 5 Amp, 0- 25 Ohm, 1 Amp, 0- 300 Ohm, 1 Amp

A.C. Energy Meter, Single Phase, 10 A, 240 V induction type

A.C. Energy Meter, Three Phase, 15 A, 440 V induction type

Kilo Wattmeter Analog, 0-1.5-3KW, pressure coil rating- 240v/440v, current rating-5A/10A Analog, portable type Housed in bakelite case

Digital Wattmeter, 230 V, 1 KW, 50 Hz

Phase Sequence Indicator, 3 Phase, 415 V

Frequency Meter, 45 to 55 Hz

DC LED Lamp, 3W, 5W, 10W (50 Nos each)

DC Pump, 24 V

PWM Controller, DC 12/24 v, 30 A

MPPT Charge Controller, DC 12/24 v, 30 A

Inverter with Battery, 1 KVA with 12 V Battery Input- 12 volt DC, Output- 220 volt AC

Solar PCU, Off grid 1 KW MPPT Sine wave Solar Power Conditioning Unit

Solar Traffic Light, 12V, 75Ah battery, 75 Wp solar panel, 12V, 10A dusk to dawn charge controller, 15 W LED lights with suitable colors and 9 m height pole all dismountable

Used water treatment solar plant demonstrator kit, 1 liter capacity

Demonstration kit for wind generation (Wind turbine with blower), 300 W

LED lights, 12 V DC

LED lights, 6 V DC

Rubber gloves, Class 00, thickness 0.5mm,Length 360mm, 0.5KV,750V Dc

Cotton gloves, cream white colour, Size: 12” Length with Free size palm & cuff

Gum boots, 14” inches gumboot.Size available (5-10)

afety Goggles, The goggle should be capable of resisting impact from a 6.35 mm (1/4 inch) diameter steel ball fired at a velocity of 45.7 mps or 150 fps at specified parts of the Polycarbonate lens and should be tested by placing sample eyewear on a head form.

Safety Helmet, mediumSize ,Head Band Size ( 540 -590 in mm)

First Aid Kit, Standard

Fire Extinguisher CO2, 2 KG

Fire Buckets, Standard size

A) Compressor unit suitable for Pressure: 8 bar, Delivery: 50 lpm (or more), Reservoir capacity: 24 Litres (or more), 230V, 50 Hz, with pressure regulator and water separator. B)Pneumatic Trainer Kit, each consisting of the following matching components and accessories: - 01 sets I. Single acting cylinder Max. stroke length 50 mm, Bore dia. 20 mm - 1 No II. Double acting cylinder Max. stroke length 100 mm, Bore dia 20 mm, magnetic type - 1 No III. 3/2-way valve manually-actuated, Normally Closed - 2 Nos. IV. 3/2-way valve pneumatically-actuated, spring return - 1 No V. One-way flow control valve - 2 Nos. VI. 5/2-way valve with manually-operated switch - 1 No VII. 5/2-way valve pneumatically-actuated, spring return - 1 No VIII. 5/2-way pneumatic actuated valve double pilot - 1 No IX. 3/2-way roller lever valve direct actuation Normally Closed - 2 Nos. X. Shuttle valve (OR) - 1 No XI. Two-pressure valve (AND) - 1 No XII. Pressure gauge 0-16 bar - 1 Nos. XIII. Manifold with self-closing NRV, 6-way - 1 No XIV. Pushbutton station for electrical signal input with 3 illuminated momentary-contact switches (1 NO + 1 NC) and 1 illuminated maintained- contact switch (1 NO + 1 NC), Contact load 2A - 1 No XV. Relay station with 3 relays each with 4 contact sets (3NO+1NC or Change-over type), 5 A - 1 No XVI. 3/2-way single solenoid valve with LED - 1 No XVII. 5/2-way single solenoid valve with manual override and LED - 1 No XVIII. 5/2-way double solenoid valve with manual override and LED - 1 No XIX. Power supply unit, Input voltage 85 – 265 V AC, Output voltage: 24 V DC, Output current: max. 4.5 A, short-circuit-proof. - 1 No XX. Profile plate, Anodised Aluminium 1100x700 mm, with carriers. C) Pneumatic Workstation with 40 square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metallic full panel drawer slide: (1) Worktable – Size (Approx.) L 1200mm X W 900mm X H 900 mm, with four castor wheels including two lockable wheels at the front side, (2) Drawer – Size (Approx.) – L460mm x W495mm x H158mm each, and overall size of Drawer unit (Approx.) - L470mm x W495mm x H825m m and (3) Drawer slide height (Approx.) 85mm. D)Carrier for mounting components, such as PB & relay boxes. E) Cut section model for pneumatic components, Mention in Item description and

A) Hydraulic Trainer Kit, each consisting of the following matching components and accessories: I. Hydraulic Power pack with (1) external gear pump having a delivery rate of 2.5 lpm, (approx.) @ 1400 rpm operating pressure 60 bar, coupled to a single-phase AC motor (230 V AC) having start capacitor and ON/OFF switch and overload protection, (2) pressure relief valve adjustable from 0 – 60 bar, (3) oil reservoir, ≥5 litres capacity having sight glass, drain screw, air filter, and P and T ports. II. Pressure relief valve pilot-operated - 1 No III. Drip tray, steel size 1160 mm x 760 mm. - 1 No. IV. Pressure Gauge Glycerin-damped, Indication range of: 0 – 100 bars - 1 No. V. Four-Way distributor with five ports, equipped with a pressure gauge - 1 No. VI. Double acting hydraulic cylinder with a control cam, Piston diameter16 mm, Piston rod diameter10 mm, Stroke length 200 mm. - 1 No. VII. Suitable Weight for vertical loading of hydraulic cylinder - 1 No. VIII. Mounting kit for weight for realizing pulling and pushing load. - 1 No. IX. 3/2-way directional control valve with hand lever actuation. - 1 No. X. 4/2-way directional control valve with hand lever actuation. - 1 No. XI. 4/3-way directional control valve closed-centre position, with - 1 No. hand lever actuation. - XII. Non-return valve. - 1 No. XIII. Pilot-operated check valve Pilotto open. - 1 No. XIV. One-way flow control valve Withintegrated check valve. - 1 No. XV. T-Connector with self-sealing coupling nipples (2 Nos.) and quick coupling socket (1 No.). - 2 Nos. XVI. Profile plate, Anodised Aluminium, 1100x700 mm, with carriers, mounting frames and mounting accessories (To be fitted onto the Hydraulic workstation) - 1 set B) Hydraulic Workstation with 40 square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metallic full panel drawer slide: (1) Worktable – Size (Approx.) L1200mmXW900mmXH900 mm, with four castor wheels including two lockable wheels at the front side, (2) Drawer – Size (Approx.) – L460mmxW495mm xH158mm each, and overall size of Drawer unit (Approx.) L470mmxW495mmxH825m m and (3) Drawer slide height (Approx.) 85mm. C)Cut-section models for hydraulic components , Mention in Item description and

RAMKRISHNA UDYOG

SUSHAMA ELECTRONICS

Arati Trading