REPAIR TO DRAINS, PATH, FENCING, GATES, RETAINING WALLS ETC AT AGE B/R-II UNDER GE 859 EWS

Amount

Demolition of cement concrete in ground floors and pavings n.exc 15 cm thickness (below or above ground level).

Demoloition of cement concrete of any description and in any situation not otherwise specifically provided for.

Dismatling of mild steel work any description.

M&L for PCC 1:4:8 type D2 using 40 mm graded stone aggregate in foundations, filling and mass concrete

M&L for PCC 1:3:6 type C2 using 40mm graded stone aggregate as in foundation of RCC post or struts.

S & F in repair mild steel post and struts in fencing including cutting tops to shape as swan neck drilling holes ,notching for wire etc.and flate iron fillets for securing wire mesh etc confirming to gde Fe 410-0 or Fe 310-0complete as specified.

Fixing and fabrication only for mild steel post and struts in fencing including cutting tops to shape as swan neck drilling holes ,notching for wire etc.and flate iron fillets for securing wire mesh etc confirming to gde Fe 410-0 or Fe 310-0 complete as specified.

S & F in repair for MS screw bolt(Machine made) with hexagonal or squre heads at one end and screwed the other or screwed both ends and dia of bolt 11 to 15 mm and length exc 5 cm n exc 10 cm long .

S & F in repair for galvanised 2 strand steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to angle fencing post complete all as specified.

Fixing only in repair for galvanised 2 strand steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to angle fencing post complete all as specified.

Supply only chain link fencing mesh size of 100 x 100 mm of 4mm dia galvanised wire.

Fixing only chain link fencing incl line wire any mesh size and type of standrds rails, straining bolts incl provn of binding wire.

M&L for Mild steel Tie bars 10 mm dia.with screwed ends,nut, washers and mild steel plates for chain link fencing all as specified and directed.

M& L for preparation of new steel surface of any description exc 10 cm width or girth not otherwise described and applying Two coats of synthetic enamel paint over a coat of red oxide.

M& L for preparation of new steel surface of any description n exc 10 cm width or girth not otherwise described and applying Two coats of syntheticenamel paint over a coat of red oxide.

Formwork to sides of concrete foundations, footings, bases of columns, raft and faft beams, sides and soffits (if any ) of foundation and plinth beams, and similar work, vertical or to batter for fair finished surface.

Scarifying or picking gravelled, mecadam or bituminous macadam surfaces in area n.exc 400sqm, exc 50mm n.exc 100mm deep

Labour only for hard core of gauge n.exc 63mm, deposited, spread and levelled in layers nexc 15 cm thick, watered and rammed to a true surface.

M & L 75mm thick cement concrete type C2 (1:3:6) using (40mmgraded aggr.) as in sub base

M&L for 20mm thick screed bed or bedding layer in CM (1:6) for laying floor finishes.

M&L for continuous PCC block edging, with 7.5cm thick PCC block (1:3:6) C1 (block size 300x200x75mm) , laid dry on edge vertically with width equal to the blocks and removel of surplus soil if any.

M&L for Chequered cement concrete tiles 200x200x25mm etc. set and jointed and pointed in neat cement slurry in floor with grey cement and pigment all as directed.

M&L for 75 mm thick Cement concrete type C2, 1:3:6 (using 40 mm graded stone aggregate) in paving and spike rolling to surface or making impression of expended metal whilst the concrete is green.

M&L for 150mm thick Cement concrete 1:3:6 type C2 using 40mm grade stone aggregate all as specified and directed.

M&L for 100mm thick Cement concrete 1:2:4 type B-1 using 20mm grade stone aggregate laid on floor, finishing cemnet concrete surface even and smooth without using extra cement complete all as specified and directed.

Forming 12mm thick Expansion joints filled with pro-formed bituminous filler and top 30 mm primed and sealed with sealing compound, grade A all as specified and directed.

M&L for PCC Type B1(1:2:4 ) in roof kerbs or mud stops, rounded or chamfered on edges including necessary formwork.

Demolition of 100 mm SWG drain pipe and Material and labour for PVC (SWR) pipes 110 mm single socketed, in any length with rubber ring joints, laid in trenches.

Material and labour for providing PCC (1:3:6) type C-2 as in concrete bed to drain pipes including packing under and haunching against the sides of pipes of bore 100mm on after they are laid and tested complete all as specified and directed..

Demolition of reinforced Cement Concrete of any description and in any position not otherwise specifically provided for.

M&L for providig precast cement concrete in cover slabs using type B1 1:2:4 & setting in cement mortar 1:6.

M&L for pre cast reinforced cement concrete type B-l, 1:2:4 (20 mm graded aggregate) in precast posts, fencing posts, straining or terminal posts, struts etc. for fencing, average sectional area n.exc 100 sq. cm with or without chamfered angles and flat, splayed, rounded or mitred tops as directed.

M&L for pre cast reinforced cement concrete type B-l, 1:2:4 (20 mm graded aggregate) in precast posts, fencing posts, straining or terminal posts, struts etc. for fencing, average sectional area exc 100 sq. cm n.exc 200 Sq cm, with or without chamfered angles and flat, splayed, rounded or mitred tops as directed.

M&L in mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

M&L for Mild steel TMT bars 6mm to 8mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips.

Demolition of precast block walling built in cement mortar.

M&L for PCC 1:3:6 type C2 block masonry with solid blocks, exc 10cm in width and setting in cement mortar 1:4 complete.

Material and labour for 15mm thick rendering in cement mortar (1:4) on brick or concrete surfaces with WPC. Note : WPC shall be measured and paid separately.

Supply only Integrated water proofing compound ISI marked

M&L for Preparing new plastered surfaces and applying Two coats of cement base paint on surfaces of walls on plastered surfaces

M&L for Preparing newly plastered surfaces of walls and applying three coats of white wash.

M&L for Plain cement concrete (1:3:6) type C-2, using 40mm graded stone aggregates in surface channel, bed of drains incl form work / moulds complete all as directed.

Extra for fair finishing drain or channels 30 cm inner girth in cement concrete using extra cement including forms, moulds etc.

Add or deduct item no 43 above for each 25mm inner girth or part there of over or under 30cm inner grith in cement concrete using extra cement including forms, moulds etc.

Taking down cement plaster on stone , brick, concrete block wall or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc.

M&L for rendering 15mm thick in CM 1:4 on concrete surfaces finished even and smooth with neeru finish using extra cement .

Dimolition of brick and stone masonry of any description in CM.

M&L for walling of RR, uncoarsed, well bonded bedded & solidly hearted built in cement mortar 1:6.

M&L for for walling of RR, uncoarsed, well bonded bedded & solidly hearted built in cement mortar 1:6.

Extra over stone walling for hammer dressing to face stones & dressing to face beds and joints as specified at RR walling uncoarsed or brought upto coarse, max depression on face from straight edge held against the dressed surface n.exc 20 mm granite or trap stone.

M&L for raised pointing to RR, uncoarsed or brought upto course stone masonry in cement mortar 1:3.

M&L for flush pointing to RR, uncoarsed or brought upto course stone masonry in cement mortar 1:4.

M&L for providing pre cast PCC bonders (for stone walling), type B1 1:2:4 (20 mm graded aggregate) set in cement mortar 1:6.

M&L for Hand packing(any thk)at back filling with broken stone or boulders.

M&L for providing cement concrete in coping type B1 1:2:4 (20 mm graded stone aggregate) in coping.

S&F 110 mm dia PVC (SWR) pipe in any length with rubber joints laid in trenches or floors

M&L for mild steel work as in gate framed work of angle or other section with gusset plates braces etc complete

M/S SUNRISE CONSTRUCTION AND CO

mon traders

passang construction

M/S ARUNACHAL GENERAL PROVISION STORE

M/S MURPHEW ENTERPRISES

M/S RARAI ENTERPRISES