Construction work of office building of UP Vigilance Establishment Kanpur Sector.

Amount

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. DSR 2.31

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-incharge..All kinds of soil. DSR 2.6.1

Earth work in excavation by mechanical means (Hydraulic excavatior)/manual means over areas(exceeding 30cm in depth. 1.5m in width as well as 10sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. In all kind of soil upto 1.5m to 3.0m. Depth DSR 2.6.1+2.26.1

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc.in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift. DSR 2.25

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. DSR 2.27

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) DSR 4.1.8

Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete. Upto Plinth. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the minimum specified cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. Concrete of M20 grade with minimum cement content of 270 kg /cum. DSR 4.20.1.3

Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete. Above Plinth. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the minimum specified cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. Concrete of M20 grade with minimum cement content of 270 kg /cum. DSR 4.20.2.3

Centering and shuttering including strutting, propping etc. and removal of form work for :Foundations, footings, bases for columns. DSR 4.3.1

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in : Cement mortar 1:4 (1 cement : 4 coarse sand). DSR 6.1.1

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:4 (1 cement : 4 coarse sand). DSR 6.4.1

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil. DSR 4.13

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor : With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. DSR 2.35.3.1

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo Mechanically Treated bars of grade Fe-500D or more. DSR 5.22.6

Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod pf approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS:16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for : (1) Sites with basic wind speed > 45 m/s as per IS 875-Part 3, (2) Sides with structure hight more than 20 m for all wind speeds. Two track two pannel sliding window with aluminium channel for roller track, wool pile, nylon rollers with SS-304 body. Using R2 series with frame (40 mm & above ) x (40 mm & above) & sash (25mm & above) x (50mm & above) with zinc alloy (Zamak) powder coated touch lock with hook (Height upto 1.20 meter). DSR 9.147.A1.1

Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod pf approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS:16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for : (1) Sites with basic wind speed > 45 m/s as per IS 875-Part 3, (2) Sides with structure hight more than 20 m for all wind speeds. Three track Three pannel sliding window with two glazed one wire mesh panels woth aluminium channel for roller track, wool pile, nylon rollers with SS-304 body. Using R3 series with frame (98 mm & above ) x (40 mm & above) & both and fly screen sash (30 mm & above) x (55 mm & above) with zinc alloy (Zamak) powder coated handle on every glazed panel along with multi point locking system. (Height upto 1.80 meter). DSR 9.147.A4.2

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using flats 30x6mm for diagonal braces and central cross piece(Using M.S. angels 40x40x6 mm for diagonal braces). DSR 10.5.1

Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame. DSR 9.121

Providing and fixing to existing door frames 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856, complete as per direction of Engineer-in-charge. DSR 9.122.2

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:Profile E.(Fixing with adjustable lugs with split end tail to each jamb). DSR 10.14.3.1

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters : 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. DSR 9.20.1

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). DSR 9.23

Providing and fixing bright finished brass Sliding Door bolts with necessary screws etc. complete : : 300 x16 mm. MR

Providing and fixing bright finished brass Sliding Door bolts with necessary screws etc. complete : : 250 x16 mm. MR

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250x10 mm. DSR 9.74.1

Providing and fixing bright finished brass handles with screws etc. complete: 125 mm. DSR 9.81.1

Providing and fixing bright finished brass handles with screws etc. complete: 100 mm. DSR 9.81.2

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. DSR 9.82

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. DSR 9.83

Providing and fixing Door Seal with necessary accessories and screws etc. complete. MR

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to steel windows by welding. DSR 9.48.1

Providing & fixing 12 mm thickness Toughened glass panes. DSR 8778

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with . 5.0 mm thick glass panes. DSR 10.30.2

Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4mm wide aperture with matching wood beading. DSR 9.7.8

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). DSR 10.28

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge : 22.7.1 With average thickness of 120 mm and minimum thickness at khurra as 65 mm. DSR 22.7.1

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. DSR 22.5

15 mm cement plaster on rough side of single or half brick wall of mix : 1:4 ( 1 cement: 4 coarse sand ) DSR 13.5.1

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. 10 to 13m. DSR 13.22

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. 13m to 16mm. DSR (2x13.22)

12 mm cement plaster 1:4 (1 Cement : 4 Coarse Sand). DSR 13.4.1

Forming groove of uniform size from 12x12 mm and upto 25x15 mm in the top layer of washed stone grit plastered surface as per approved pattern, including providing and fixing aluminum channels of appropriate size and thickness (not less than 2 mm), nailed to the under layer with rust proof screws and nails and finishing the groove complete as per specifications and direction of the Engineer-in-Charge. DSR 13.76

Washed stone grit plaster on exterior walls height upto 10 metre above ground level, in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand ), furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 2 Kg of cement per square metre, top layer 15 mm cement plaster 1:1/ 2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10 mm nominal size), in panels with groove all around as per approved pattern, including scrubbing and washing the top layer with brushes and water to expose the stone chippings ,complete as per specification and direction of Engineer-in-charge (payment for providing grooves shall be made separately). DSR 13.72

Extra for washed grit plaster on exterior walls of height more than 10 m from ground level for every additional height of 3 m or par thereof. (10m to 13m). DSR 13.74

Extra for washed grit plaster on exterior walls of height more than 10 m from ground level for every additional height of 3 m or par thereof. (13m to 16m). DSR (2x13.74)

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. DSR 5.30

Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) : DSR 11.19.1

Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 6mm nominal size ), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of the jambs, sills and soffits. DSR 5.18.1

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. DSR 8.31

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc.,the tiles must be cut with zero Chipping dimond cutter only . laying of tiles will be done with notch trowel plier wedge clips of required thickness , levelling system and rubber mallet for placing the tiles gently and easily. Double charge vitrified tile polished finish of size Glazed vitrified tiles matt/ anti Skid finished of Size 600X600mm. DSR 11.41A.3.1

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Double charge vitrified tiles polished finish of Size (600x600mm). DSR 11.41.2

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. Granite stone slab of colour black, Cherry/Ruby red. Area of slab upto 0.50 sqm. DSR 8.2.2.1

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work. DSR 8.3.2

Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss finish complete. DSR 8.6

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. DSR 13.26

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. DSR 13.8

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications.Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr/10 sqm. DSR 13.48.1

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:13.47.1 New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm). DSR 13.47.1

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand or manufacture. DSR 13.48.3

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. DSR 4.17

P/L 25mm OB brick Ballast under floor of toilet sunken roofs. DSR 2909

Add for using extra cement in th Items of Design Mix over and above the specified Cement Content In M-20 Concrete 300Kg/cum cement instead of 270 Kg/cum. DSR 367

Fiberglass mesh with alkali-resitant coating having massper unit area ≥145g/m2 mesh size 3.9x4.0mm +- 10% DSR 1257

Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, upto 25 metre height, above ground level, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge. DSR 14.72

Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings.The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding , other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured. DSR 25.8

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately). DSR 21.18

Providing and fixing stainless steel fancy handle of approved make fixed with SS screws etc. complete as per direction of Engineer-in-charge. DSR 9.170.1

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. DSR 9.76

Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991, in true horizontal level suspended on interlocking metal powder coated T-Grid of hot dipped galvanised iron section of 0.40 mm thick on Silhouette profile,rotary stiched double webbed white with 6mm reveal profile (white/black), comprising of main-T runners of size 15x42mm of length 3000 mm, cross - T of size 15x42 mm of length 1200 mm and secondary intermediate cross- T of size 15x42 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 22x19x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge. DSR 26.23

Providing and fixing in wall lining medium density fibre board IS: 14587:1998 marked, Pre-laminated one side decorative lamination and other side balancing lamination, with necessary fixing arrangement and screws etc. complete. 18 mm thick. DSR 9.158.2

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests DSR 17.1.1

Providing and fixing vitreous china dual purpose closet suitable for use as squatting pan or European type water closet (Anglo Indian W.C pan) with seat & lid fixed with C.P. brass hinges and rubber buffers, 10 litre low level flushing cistern with fitting and brackets, 40 mm flush bend, 20 mm over flow pipe, with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : White vitreous china dual purpose WC pan with white solid plastic seat and lid with white vitreous china flushing cistern and C.P. flush bend. DSR 17.68.1

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. DSR 17.16A

Providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C. automatic flushing cistern, with fittings, standard size G.I. / PVC flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and C.P. brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required : Single squatting plate with 5 litre P.V.C. automatic flushing cistern DSR 17.6.1

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Single half stall urinal with 5 litre P.V.C. automatic flushing cistern DSR. 17.5.1

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps DSR 17.7.2

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. DSR 17.22A

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work DSR 8.3.2

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink with drain board510x1040 mm bowl depth- 200 MM DSR 17.10.1.3

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. DSR. 17.31

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 1500x450 mm DSR-17.32.4

Providing and fixing toilet paper holder : C.P. brass DSR-17.34.2

Providing and fixing M.S. holder bat clamps of approved design to C.I. or S.C.I. rain water pipes embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and cost of cutting holes and making good the walls etc.100mm DSR-12.38

Providing and fixing soil, waste and vent pipes :100mm dia Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905 DSR 17.35.1.3

Providing and fixing soil, waste and vent pipes :75mm dia Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905 DSR 17.35.2.3

Providing and fixing single equal plain junction of required degree : 100x100x100 mm Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 DSR. 17.44.1.3

Providing and fixing plain bend of required degree.100 mm dia Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside as per IS:15905 17.39.1.3

Providing and fixing single unequal plain invert branch of required degree :100X100X75mm Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 DSR 17.52.1.3

Providing and fixing shielded coupling for Hubless centrifugally cast iron pipe 100 mm dia SS 304 grade coupling with EPDM rubber gasket DSR 17.57A.1

Providing and fixing shielded coupling for Hubless centrifugally cast iron pipe 75 mm dia SS 304 grade coupling with EPDM rubber gasket .DSR 17.57A.2

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors.Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 DSR-17.60.1.3

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. . DSR-17.73.2

Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements. Weighing not less than 106 gms. DSR 18.65

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 DSR 19.30.2

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design : Inside dimensions 600x850 mm and 45 cm deep for pipe line with three or more inlets : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 DSR 19.30.3.1

Supplying and fixing C.I. cover without frame for manholes :455x610 mm rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg. DSR 19.18.1

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete.150 mm dia. R.C.C. pipe DSR-19.6.2

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : DSR-19.6 300 mm dia. R.C.C. pipe DSR-19.6.3

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. : Concealed work, including cutting chases and making good the walls etc.20mm dia nominal bore. DSR 18.8.2

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : External work 25mm dia nominal bore. DSR 18.9.3

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : External work 32mm dia nominal bore. DSR 18.9.4

Supply and Fixing C.P. brass bib cock heavy quality short body of 15mm. dia.(L&K,Jaquar Essco) DSR 18.49.1

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore. DSR.18.50.1

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Semi rigid pipe32 mm dia. DSR 17.28.1.1

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Semi rigid pipe40 mm dia. DSR 17.28.1.2

Providing and fixing C.P Angle valve 15mm dia (L&k,Jaquar ESSCO or equiv.) for geyser points of approved quality 15 mm nominal bore. DSR 18.53.1

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. DSR 18.53A

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length DSR 18.74.2

Providing and fixing PTMT grating of approved quality and colourRectangular type with openable circular lid. 150 mm nominal size square 100 mm diameter of the inner hinged round grating DSR 18.58.2.1

Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, depth up to 1.5 m, including getting out the excavated materials, returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layers by ramming, watering etc., stacking serviceable material for measurements and disposal of unserviceable material as directed, within a lead of 50m : Pipes, cables exceeding 300 mm dia but not exceeding 600mm dia DSR 2.13.1.3

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design :.300 mm diameter S.W. pipe DSR 19.3.5

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. DSR 18.48

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.DSR-12.41.2

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore. DSR 18.17.1

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 32 mm nominal bore. DSR 18.17.2

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore. DSR 18.18.3

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift up to 1.5 m, as directed by Engineer-in-Charge. DSR 2.1.1

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re- olling the sub grade and disposal of surplus earthwith lead upto 50 metres. DSR 16.1

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineerin- Charge. With material conforming to Grade-III (size range 26.5 mm to 0.075 mm ) having CBR Value-20 DSR 16.78.3

Construction of dry lean cement concrete sub base over a prepared sub-grade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per specifications, cement content not to be less than 150 Kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-10 tonne vibratory roller, finishing and curing etc. complete as per direction of Engineer-in-charge. DSR 16.80

Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber,finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in-charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately). Cement concrete manufactured in automatic batching plant (RMC plant) i/c transportation to site in transit mixer. DSR 16.43.2

Providing and fixing pre-moulded joint filler in expansion joints of RCC roads / CC pavements after making the joints dust free with high pressure air jet cleaners, all complete as per direction of the Engineer-in-Charge. (Pre-moulded joint fillers shall be made of bitumen hot sealing compound impregnated fibre board having impregnation more than 35%, conforming to IS:1838 for fibre board and IS: 1834 for hot sealing bitumen compound grade A.) DSR 16.45

Providing and filling in position rubberized bitumen hot sealing compound for sealing of expansion joints in roads / pavements all complete as per direction of the Engineer-in-Charge. DSR 16.46.1

Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction of Engineer in-Charge.80mm thick Cement concrete paver block of M-35 grade with approved colour, design & pattern. DSR 16.91.2

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineerin- charge (length of finished kerb edging shall be measured to calculate volume for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). (300x300x150)mm, DSR 16.69

Providing and applying 2.5 mm thick road marking strips (retro-reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications. DSR 16.62

Providing and fixing post delineators made of ABS round body fitted with 2 nos 100 mm dia high reflective reflectors and mounted on MS pipe of 65 mm dia duly powder coated anti-rust and anti theft steel to be installed as per direction of Engineer-in-charge. DSR 16.65

Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measuresmounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours).Cautionary /warning sign boards of equilateral triangular shape having each side of 900 mm with support length of 3650 mm DSR 16.59.2

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement All works upto plinth level Concrete of M25 grade with minimum cement content of 330 kg /cum DSR 5.33.1.1

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement All works Above plinth level Concrete of M25 grade with minimum cement content of 330 kg /cum DSR 5.33.2.1

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer, of required shade and colour all complete : New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre. DSR 13.41.1

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron ‘Y’ shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5 mm thick) wire of high tensile strength of 165 kg/ sq. mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately) DSR 16.53

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all [email protected]/rmt DSR 10.1

Providing M.S. foot rests including fixing in manoholes with 20x20x10 cm cement concrete blocks 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) as per standard design:With 20x20mm square bar DSR 19.15.1

Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality.M.D. -10- Circular shape 500mm internal diameter DSR 19.19.2.2

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-incharge, upto 90 metre depth below ground level.Drilling of 300mm dia bore hole manually. DSR 23.1.1.1

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.150 mm nominal size dia DSR 23.4.2

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. DSR 23.5

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.DSR 23.6

Supplying, filling, spreading & leveling coarase sand of size range 1.5 mm to 2mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer-in-charge. DSR 23.7

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/medium/coarse, in required grading & size as per actual requirement, all complete as per direction of Engineer-in-charge. DSR 23.8

Excavating trenches in all kind of soil of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5 m. including getting out the excavated soil & then returning the soil as required,in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering, etc & disposig of surplus excavated soil as directed within a lead of 50m.Pipes, cables etc. exceeding 80mm dia. But not exceeding 300 mm dia. DSR 2.10.1.2

Providing, laying and joining glazed stone ware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete. 150mm diameter DSR 19.1.2

Providing & laying cement concrete 1:5:10 (1 cement :5 coarse sand :10 graded stone aggregate 40mm nominal size) alround S.W. Pipes including bed concrete as per standard design.150mm diameter S.W. Pipe DSR 19.2.2

Constructing masonry Chamber 60x60x75 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement :4 coarse sand ) for sluice valve, with C.I. surface box 100mm top diameter, 160mm bottom diameter and 180mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design :With F.P.S. bricks DSR 18.33.1

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. DSR 23.12

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 150 mm nominal size dia ( Item Code DSR-23.3.2) (150 mm Dia)

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:.150 mm cap . ( Item Code DSR-23.13.2)

Providing and fixing GI pipe complete with GI fitings and clamps, I/C cutting and making good of walls /Lowering in bore well etc. 32 mm dia DSR 18.10.4

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.150 mm clamp . ( Item Code DSR-23.14.2)

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). of: 150 mm Dia . ( Item Code DSR-23.15.2)

Adhesive Solvent Cement . DSR -8012

Stainless steel Male Threaded Elbow 900 for 34.00 mm outer dia X 32 mm nominal dia threaded DSR 8931

2 HP 12 Stage submersible pump of ISI mark with automatic Starter panel. Qutation/ MR

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conducter, single core cable in surface recessed steel conduit as required 2x2.5 sqmm 1x2.5 sqmm earth wire. DSR E & M 1.7.2

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources) DSR 4.1

Providing and fixing factory made Fiberglass Reinforced plastics (F.R.P.) chajja 4 mm thick of required colour, size and design made by Resin Transfer Moulding (RTM) Machine Technology, resulting in void free compact laminate in single piece, having smooth gradual slope curvature for easy drainage of water and duly reinforced by 2 nos vertically and 1 nos horizontally 50x2 mm thick M.S. flat with 12 mm in built hole for grouting on the existing wall along with the 50 mm flanges duly inserted and sealed in the wall complete in one single piece casted monolithically, including all necessary fittings . The FRP Chajja should be manufactured using unsaturated Polyester resin as per IS: 6746, duly reinforced with fibre glass chopped strand mat (CSM) as per IS: 11551 complete with protective Gel coat U/V coating on Top for complete resistance from the extreme of temperature, weather & sunlight (Only plan area of chajjas shall be measured for making payment). DSR 9.128

Excavating, supplying, stacking and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift. DSR 2.25 (a)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 1x1.5 sq mm.(for Inverter)

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required (2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire)

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required (2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire)

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required (2 X 4 sq. mm + 1 X 4 sq. mm earth wire)

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required (2 X 6 sq. mm + 1 X 6 sq. mm earth wire)

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required (4 X 10 sq. mm + 2 X 6 sq. mm earth wire)

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required (4 X 16 sq. mm + 2 X 6 sq. mm earth wire)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required. for Aquaguard Board ( 15/16 A Switch & 6 Pin 15/16 A socket outlet 2-2 Nos.)

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 Nos. 3 pin 5/6 A modular socket outlet and 2 Nos. 5/6 A modular switch, connections etc. as required. (For light plugs Computer Pts. to be used in non residential buildings).

T.V. Board (Supplying and fixing 8 modules, GI box along with modular base & cover plate with Modular type 5/6 A Switch & 3 Pin 5/6 A Socket outled 2-2 Nos., TV antenna socket outlet-1 No., Blanking Plate-1 No. )

Supply and fixing of LED Tube Light with heavy duty Metal Box type Tube Light fitting Ix22 watt suitable for upto 1x 22 watt LED Polycarbonate tube light complete Including tube suitable for both surface & suspended conplete in all respect CATAAA 2620 system lumens 120 lm /w PF>0.95, THD<10%,CRI>80 Sheet thickness 0.8mm,tube with aluminium heat sink> 300V over voltage protection, 2.5 KV internal surge protection with 5 year Warrantee.

Supply and fixing of IP 20, Front Lit, Mid Power SMD type LED light, recess/ Surfae mounting round 10 Watt to 15 Watt , Cut out Min 125 mm, Height Min 40 mm,, LED Down Lighter having Powder coated die cast aluminiun housing with heat sink, High purity transmisivity UV Stabilized Non yellowish diffuser/ Reflector for unifom light distribution, detachable driver set, stable for 24 Hr Continous Operation, Complete in All respect. CAT-AAA 1200-1800 system lumens, >120 Lm/W, PE>0.95. THD <10% at full load, CRI >80,,>300V over voltage portection, 2.5 KV inlernal Suge Proteclion, with 5 years warrantee.

Supply and fixing of IP 20, Mid Power SMD type LED Light, 2'x2' 36Watt to 46Watt, Indoor Recess mounting LED Square Fitting for Armstrong Ceiling Powder coated CRCA housing body, High purity / transmisivity UV Stabilized Non yellowish diffuser/ Reflector for uniform light distribution, detachable driver set, open and short circuit protection, suitable for 24 Hr Continuous Operation, Complete in All respect. CAT-AAA 4320-5520 system lumens, with fully covered diffuser type, >120 Lm/W, PF>0.95, THD <10% at full load, CRI >80, >300V over voltage protection, 4 KV internal Surge Protection,with 5 years warrantee.

Supply & fixing of water tight oblong 10 watt LED Bulkhead luminaire having pressure die cast housing with driver set confirming to IP65 and above protection, IK 08, High purity transmisivity UV Stabilized Non yellowish diffuser/ for uniform light distribution, delachable driver set, open and short circuit prolection, suitable for 24 Hr Continuosus operation CAT-AAA 1200 system lumens, >120 Lm/W, PF>0.95, CRI >70, >300V over voltage protection, 4 KV internal surge protection, metal housing 5 Year warantee.

Supply of Celling fans with fan motor of A.C. Permanent insulation, capacitor rating. The rated voltage 220/240 Volts, 50 Hz, I-ph AC the fan assemble should consists of down rod blades, shackle canopies etc and with double ball bearing system. 1200 mm. sweep.

Supply and fixing of Single LED light wall bracket 9 Watt on matching M.D.F.E.G. Board base etc. Complete in all respect.

S/F of LED Mirror Light fitting 20 Watt complete in all respect Philips or equivalent.

S/F of 9 Watt LED Bulb Havells or equivalent.

Supply of Heavy Duty Exhaust Fan 300 mm. sweep 900 RPM. Havells or equivalent.

Supply Metallic body fresh air fan 300 mm. sweep. Havells or equivalent.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 12 way, Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way(4 + 12), Double door

S/f of Ekinox³ TPN DB-VTPN DPX³ 160 MCCB DB's As per IEC 61439-3,Suitable for Flush Mounting and Surface Mounting, With 250 A Copper Busbar for each phase, With 2 Neutral bar, 2 Earthbar and Cable ties for Cable management, Fully insulated busbar & shrouded Neutral bars, Improved Pan assembly for ease of installation, Prefitted masking sheet, Reversible Door for IP 43 & IP 54 DB's, With provision for DPX³ 160 MCCB as incomer and SP/TP MCB's as outgoing 6 Way

S/f of Ekinox³ TPN DB-VTPN DPX³ 250 MCCB DB's As per IEC 61439-3,Suitable for Flush Mounting and Surface Mounting, With 250 A Copper Busbar for each phase, With 2 Neutral bar, 2 Earthbar and Cable ties for Cable management, Fully insulated busbar & shrouded Neutral bars, Improved Pan assembly for ease of installation, Prefitted masking sheet, Reversible Door for IP 43 & IP 54 DB's, With provision for DPX³ 160 MCCB as incomer and SP/TP MCB's as outgoing 8 Way

Supplying and fixing following rating, Four pole, 415 volts, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A

Supplying and fixing following rating, TP, 415 volts, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A

Supplying and fixing following rating, Four pole, 415 volts, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 A

Supplying and fixing following rating, TP, 415 volts, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required. 80 A

S&F of 800 A. 415 V Heavy Duty Double Break HRC fuse type metal clad TPN complete. Havells or eqi.

S/f 100 Amp. FP Incoming Changeover Switch with Enclosure. Havells or eqi.

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, “C” curve including connections, painting etc. as required.

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single Pole

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Double Pole

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 amps

Providing and fixing following rating and breaking capacity and pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 125 Amp, 36KA, FPMCCB

Providing and fixing following rating and breaking capacity and pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 200 Amp, 36KA, FPMCCB

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

Supplying and fixing brass batten/ angle holder including connection etc. as required.

Erection of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS lamps per fitting, complete with all accessories including connection etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Providing and fixing circular/ Hexagonal GI box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick GI sheet with its top surface hacked for proper bonding, top lid shall be screwed into the GI box by means of 3.3 mm dia round headed screws, one lock at the corners, clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. DSR Rate @ Rs. 220.65

Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required 100 mm dia

Supplying and fixing Cable End Box (Loose wire box) (IP 43) suitable for following single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with testing and commissioning etc. as required. for 10 way, Double door SPN MCB DB

Supplying and fixing Cable End Box (Loose wire box)(IP 43) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with testing and commissioning etc. as required.For 4 way, Double door TPN MCBDB

Supplying and fixing Cable End Box (Loose wire box) suitable for triple pole and neutral, sheet steel, Vertical MCB distribution board, 415 V, on surface/ recess, complete with testing and commissioning etc. as required.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 70 sq. mm (38mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 120 sq. mm (38mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 400 sq. mm (82mm)

Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required. 250 mm X 300 mm X 100 mm deep

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 70 Sq. mm 3-1/2 Core

Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 120 Sq. mm 3-1/2 Core

Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 400 Sq. mm 3-1/2 Core

Supply, Installation, Testing amd Commissioning of LT Panel vermin proof floor mounting , M.S. channel base with bottom and Fabricated out of 2.0/1.6mm thick CRCA sheet steel, painted with powder coated paint of shade as per the direction of Engineer In-Charge after proper sheet treatment process of sheet steel. The Bus Bar of panel shall be of Electrical grade High Conductive Aluminum alloy of appropriate cross section as per rating.The main bus bar shall run throughout the panel of rating as main incomer rating. The Bus Bar shall be supported by non hygroscopic SMC/DMC Bus Bar supports which shall be mounted on proper interval to ensure the bear the jerks of short Circuit of 50kA for panels having ACB as Incomer & 36kA for panels having MCCB Incomers. Panel shall be constructed in fully Segregated Compartment Design for Each Feeder as per 3b construction Format. The Panel shall be completed in all respect as per IS: 8623 Part-2&3. There shall be Separate Metering Compartment for incomer metering and outgoing metering. All Incomer Feeders shall be provided with Multifunction Metering along with Phase Indicating Lights and other associated components such as CT, control MCB Terminal Block etc. and all Outgoing Feeders 100A & above shall be provided with 3 phase Ammeter along with phase Indicating Lights and other associated components such as CT, control MCB Terminal Block etc.

The Feeders above shall be provided ac accommodated all Measuring Instruments shall be Digital type & all Indicating Lights shall be LED type. Wiring shall be done from 1100V Grade PVC Insulated copper flexible wire. All ACB shall be Electrically operated Draw-out type with Microprocessor Based O/L, S/C & E/F Release of Breaking/ Withstand Capacity (ICU/ICs/Icw) 50kA or more All MCCB shall be Thermal Magneetic/Microprocessor with O/L & S/C Protection along with Required Spreaders & Extended Rotary Handle with pad Locking facility of Breaking capacity (ICU/ICS) 36kA or more All MCB shall be Thermal 10kA 'C' Curve. Cubicle type switch board shall be Cat-A and B only. Incomer:- 630 A FP, 36 kA - 1 Nos. Outgoing:-200 A FP, 36kA MCCB with O/l & S/C protection release along with extended rotary handle & spreaders-1 Set. Outgoing:-160 A FP, 36kA MCCB with O/l & S/C protection release along with extended rotary handle & spreaders-2 Set. Outgoing:-100 A FP, 36kA MCCB with O/l & S/C protection release along with extended rotary handle & spreaders-1 Set. Outgoing:-63 A FP, 36kA MCCB with O/l & S/C protection release along with extended rotary handle & spreaders-2 Set. Supply & fixing of 7 mtr GI Octagonal Pole of approved make (top dia 70mm, Bottom dia 130 mm and base plate 12mm thik) having 3mm thikness with Single arm bracket (1 Mtr length each ) on RCC foundation including the cost of foundation, foundation bolts, excavation & back filling and Required T&P completee in all respect.

Supply and fixing of LED Street light Fitting with mandatory driver set having die cast aluminium body with toughend glass/ UV stabilized PC Cover and lenses suitable for 75 Watt. to 90 Watt and Confirming to IP 66, and IK07 and above protection having Company LOGO Engraved complete in all respect including Labour. CAT-AAA 9000-10800 system lumens, High Power LED with lenses, 120 Lm/W, PF>0.95, THD <10% at full load, CRI >70,, Potted driver Set in Metal housing (Not Circuitory) Phase to phase Protection at 440V & >300V auto cut and re-start feature, with 5 years warrantee

S/l of FR PVC Round Sheathed Cu. Conductor flexible cable including making Connection to street Light. With 3 Core 1.5 Sq. mm. Cu. Wire

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Double pole

Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 10 sq. mm 2 core

S&F of 16 Amp./240V DP Switch fuse unit Havells or eqi.

SITC of 1 UNIT 8 PASSENGER Lift of reputed make. PRODUCT : GeN2-Nova_MRL-1MPS DETAILS : GeN2-Nova_MRL-1MPS CAPACITY (kgs) : 544 Kg, 8 persons. SPEED (mps) : 1 RISE (m) : 8 m STOPS :3 Stops With (all opening on the same side) CONTROLLER TYPE : LVA/ACD DRIVE : VF Regenerative (Closed Loop) POWER SUPPLY :400/415 Volts (3 Phase AC) OPERATION : Full collective operation CAR GROUP : One car (simplex) MACHINE : PM Gearless TRACTION MEDIA : Flat Coated Steel Belt CAR FINISH :• Rear Mid Panel = Stainless Steel #4(Hairline) •Rear Corner Panels = Stainless Steel #4(Hairline) •Side Mid Panels = Stainless Steel #4(Hairline) •Side Corner Panels = Stainless Steel #4(Hairline) •Front Panels = Stainless Steel #4(Hairline) FALSE CEILING TYPE CD-41 FALSE CEILING FINISH : Stainless Steel #4(Hairline) VENTILLATION : Cross flow fan HANDRAILS : Stainless Steel Mirror Finish Handrails on rear car panels FLOORING : Vinyl Tiles CAR DOOR FINISH : Stainless Steel #4(Hairline) etc. completion of work as direction of engineer-in-charge. LANDING DOORS FINISH : Stainless Steel #4(Hairline) PIT DEPTH : 1350 OVERHEAD 4500 HOISTWAY DIMENSIONS (W x D – mm) : 1800 mm W x 2400 mm D CAR DIMENSIONS (W x D x H - mm) : 1100 mm W x 1300 mm D x 2200 mm D CAR & HOISTWAY DOOR TYPE : Central opening (CO) doors DOOR OPENING (W x H - mm) : 800 mm W x 2000 mm H DOOR OPERATOR : DC Door Operator COP : COP for stops <= 12 (950mm) in Stainless Steel #4(Hairline) CAR POSITION INDICATOR : Monochrome LCD-Blue Background & White font HALL FIXTURES : O2000 HALL FIXTURE FACE PLATE : Stainless Steel #4(Hairline) HALL BUTTON ARRANGEMENT : Monochrome Type STANDARD FEATURES : Anti-nuisance Car Call Protection Independent Service (for Duplex only) Overload Device Nudging Emergency Firemen’s Service Emergency Car Light Unit Infrared Curtain Door Protection Door Time Protection Emergency Alarm Button Extra Door Time of Lobby & Parking Door Open/Close Button Manual Rescue Operation Belt Inspection Drive Auto Fan Cut Off OPTIONS INCLUDED : Voice Synthesizer, Intercom, Automatic Rescue Device, CCTV PROVISION (CAT 6) SITC will be done as per norms of CPWD/UP PWD.

Supply & installation of split direct expansion air conditioners suitable for operation on A/C supply single phase 50 Hz 230 volts with hermetically sealed compressor with air cooled condenser, motor capacitor and start run capacitor, relay and over load protector internal unit with one indoor and one outdoor unit. the condenser unit will be placed outside the room on the terrace to avoid noise including standard length of suitable size copper tubing covered with insulation tube. (High wall chored/cordless) suitable capacity 3 core sheathed/PVC copper cable and a battery operated wireless remote unit 1.9/2.0 ton BEE star rated: 5 star, EER 3.4 Make:-Mitsubishi/Toshiba or Eq.

Supply & installation of split direct expansion air conditioners suitable for operation on A/C supply single phase 50 Hz 230 volts with hermetically sealed compressor with air cooled condenser, motor capacitor and start run capacitor, relay and over load protector internal unit with one indoor and one outdoor unit. the condenser unit will be placed outside the room on the terrace to avoid noise including standard length of suitable size copper tubing covered with insulation tube. (High wall chored/cordless) suitable capacity 3 core sheathed/PVC copper cable and a battery operated wireless remote unit 1.5 ton BEE star rated: 5 star, EER 3.4 Make:-Mitsubishi/Toshiba or Eq.

SITC of suction/discharge pipe line in split A.C. unit up to 2.0 ton capacity including brazing, nitrile, rubber insulation 6 mm thick class 'O' etc. complete 3/8" (9.50 mm.) and 5/8" (15.90 mm) for 2.0TR/1.9TR AC Split.

SITC of suction/discharge pipe line in split A.C. unit up to 2.0 ton capacity including brazing, nitrile, rubber insulation 6 mm thick class 'O' etc. complete 1/2" (12.7 mm.) and 1/4" (6.4 mm) 1.5 TR AC Split.

Supply of wall mounted copper wounded Voltage stablizer 5 KVA capacity.

Supply of wall mounted copper wounded Voltage stablizer 4 KVA capacity.

Supply and laying of heavy duty PVC plastic braided 20/25 mm. OD flexible pipe for condensed water with clipping accessories complete.

S/f of Inter Connecting Electrical Cable for A.C (2.5 Sq. mm 4 Core.) Indoor to outdoor unit (P+N+E+Communication)

S/f of Inter Connecting Electrical Cable for A.C (2.5 Sq. mm 3 Core.)

Stand for Outer unit of A.C. with fixing on wall with all material & Labour complete in all respect.

Fabrication of Iron cage for outdoor unit of A.C. with material mild steel, & barfi jali provides sturdy protection for your outdoor AC condenser unit, keeping it safe from thives & vandals who might want to break in to the unit to steal the voluable copper parts.

Supply, Installation, Testing and Commisioning of 58.5 KVA 3 Phase 415 V, 50 Hz, liquid cooled Silent DG Set as per CPWDbased on CPCB-4 guideines comprising of disel engine of reputed make. Fitted on a common base frame along with other accessories i.e. Auto start, stop panel, battery charger, first fill of lube oil, 4 nos. chemical electrode earthing, reputed make as per PWD specification, complete in all respect including cost of freight charge from ex. works to site place, etc. Two Year warranty. Complete in all respect. Voltage 415 2%volt Rated output minimum 160 Ltr,. Governing Class-G2 No. of Cylinder-4 Speed-1500 rpm Insulation Class-H Make-Kirloskar/Cumins/Mahindra or Equivalent. SITC will be done as per norms of CPWD/UP PWD.

Providing and laying in Position Cement Concreate 1 :2: 4 (1 Cement : 2 Coarse sand : 4 Graded stone agrigate 20 mm nominal size) in Foundation of Pump, DG Set etc. including from work (GS Sheet Roofing etc. as required size has 3000 mm x 2500mm x 1000 mm = 7.5 Cum) DSR Rate @ Rs. 7878.50

S/O 32ch NVR STI-NVR32S2-4K(2 Satta) Supports 32 CH 8 MP/6 MP/ 5MP/ 4MP/3MP/1080 P/1280 x 1024 / 960 P / 720 P / 960 H/ D1 / CIF IP input. Playback - 16 CH Simultaneous Playback, Such-Timeslice,Time,Event,Tag,Smart & target Database search, Supports face dedection & compression, Support multiple Video Content Analetics Event, Such as object abanboned/missing,reson intrusion, tripwire, Video exception etc. support POS information over layon live view & Playback, express & flexible backup via USB, network & show on, Penta Plex-Preview,record,Playback,backup & remotee excess. Remote control via Web client or CMS Preview,record,Playback,backup, PTZ & Confrigration, dual streen technology for local storage with high defination, remote network transmation & remote survillance with mobile device, 4K HD Output, True high resolution display, Support PTZ preset & Auto Cruise, upto 255 presets & 8 Cruise support NAT fuction & QR Code scaning by mobile phone, Powerfull mobile survillance by smart phones with IOS & Andoid OS.. Make - Godrej/Hikvision or Equivalent

S/O 4MP lP Dome lR Camera STI-FD20lR4SM-1440PAD Maximum Resolution 4 MP, Auto Day/Night switch, 3 D DNR,WDR,HLC, BLC etc., ROI Coding Support smart Suppliment light IP 67, Support dual streem, DC 12 V/PoE Power supply Support remote mounitering by smarts Phones & Tablet PCs with iOS & Andoraid OS, Support lying crossing dedection reson intrusion dedection. support SMD. Make - Godrej/Hikvision or Equivalent

S/O 4MP lP Bullet IR Camera STI-FB2OIR4SM-1440PAD Maximum Resolution 4 MP, Auto Day/Night switch, 3 D DNR,WDR,HLC, BLC etc., ROI Coding Support smart Suppliment light IP 67, Support dual streem, DC 12 V/PoE Power supply Support remote mounitering by smarts Phones & Tablet PCs with iOS & Andoraid OS, Support lying crossing dedection reson intrusion dedection. support SMD. Make - Godrej/Hikvision or Equivalent

S/O 4MP Varifocal Motorize lP Bullet lR Camera STIVFB50IRM-1440PS (Lens 2.8-12mm) Make - Godrej/Hikvision or Equivalent

LED Screen 42" Sony 4K Display Smart TV.

S/O 08 Port l0/100/1000 PoE Giga Switch Maximum PoE - 150 Watt, 8 x 1000 Mbps PoE Ports, 2 x 1000 Mbps up link ports and 2 x 1000 Mbps SFP Ports. Support IEEE 802.3 af/at support restrain network storm, All port supported by MDI / MDIX Autoflip & Self Neg, Blitin Power supply, Maximum power of single PoE port 30 Watt fan less, Netural cooling, Small, Compact & cuiet design, suitable for desktop or wall, Support Lighting protection 4000V. Make - Godrej/Hikvision or Equivalent

S/O 16 Port 10/100/1000 PoE Giga Switch Maximum PoE - 150 Watt, 16 x 1000 Mbps PoE Ports, 4 x 1000 Mbps up link ports and 4 x 1000 Mbps SFP Ports. Support IEEE 802.3 af/at support restrain network storm, All port supported by MDI / MDIX Autoflip & Self Neg, Blitin Power supply, Maximum power of single PoE port 30 Watt fan less, Netural cooling, Small, Compact & cuiet design, suitable for desktop or wall, Support Lighting protection 4000V. Make - Godrej/Hikvision or Equivalent

HDD 10TB(Surveillance) WD/Seagate(15 days backup)

UPS 5KVA With Batteries & Accessories Supported (APC/Luminous/Tata ) PAR 6.4.1

Wireless Mouse

PVC Camera Box(Generic)

RJ45 Connectors (100 Nos Box)

HDMI Cable 4k Supported 5mtrs

2U Rack with Extension Boards & Accessories.(Securenet/D Li nk)

4U Rack with Extension Boards & Accesso ries. {Secu re net/D link)

lnstallation & Commissioning Charges

Supply and fixing steel tubulor pole 9.50 Mtr. Long designed 410 SP-36 in 3:3:6 cement concrete foundation including excavation back filling etc. without G.I Pipe and clamp complete in all respect for mounting of camera

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm. dia.

Supply of L2 Gigabit managed switch 24 Port Make D-Link or equivalent (24 Ports 10/100/1000 Mbps, 4SFP Ports combo, GESFP Samrt manegd switch.

Supply of Patch pannel CAT-6 UTP key stone type 24 port fully loaded. Make D-Link or equivalent.

Supply & drawing of UTP 4 Pair CAT-6 UTP20AWG solid Make de-Link or eq. DSR 1.53.1

S/o CAT 6 patch cord 1 Mtr. D-Link or equivalent. CAT 6 UTP 24 AWG Patch cord 3M, Plug 30 U snagless.

S/o CAT 6 patch cord 2 Mtr. D-Link or equivalent. CAT 6 UTP 24 AWG Patch cord 3M, Plug 30 U snagless.

S/0 9 U rack with accessories wall mount 9 Ux550Wx450D, Standard accessories. 1U cable manager (1), Hardware packet (1Pkt), 6 Socket 5 Amp, Power distribution Unit (1 No.) Roof mounted fan unit/90 CFM/230 V AC (1No)

Crimping, punching connectivity testing and LAN establishment charges.

Wall mounting rack, patch panel, 24 port switch installation/fixing charges.

Supply and fixing of I/O box including face plate, key stone with GI back box complete in all respect. Make D-Link or equivalent.

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.

Supplying, installation, testing & commissioning of intelligent addressable thermal (heat) detector with rate of rise cum fixed tempreature thermistor complete with base as required.

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.

Supplying Installation testing & Commissioning of Addressable Manual Call Point complete with base as required.

Supplying Installation testing & Commissioning of Addressable horn cum strobe complete with base as required.

Supplying Installation testing & Commissioning of fault isolator complete with base as required.

Supplying Laying testing & Commissioning of 2 corex 1.5 sq.mm single standard copper conductor, PVC insulated armored cable.

Supply & fixing of CO2 type fire extinguisher, 4.5 kg. capacity (ISI Marked IS:2878 & TAC approved) comlete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.

Supply & fixing of fire extinguisher, ABC Type 4.00 kg. capacity (ISI Marked IS:15683 & TAC approved) comlete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges,tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 80 mm dia.

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges,tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 100 mm dia.

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 80 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 100 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS:5312 complete with rubber gasket, GI bolts, nuts,washers etc.as required : 80 mm dia,

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS:5312 complete with rubber gasket, GI bolts, nuts,washers etc.as required : 100 mm dia,

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing and fixing in position the industrial type pressure gauge complete as required.

(A) Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (B) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS: 1520 (C) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325. (D) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. (E) Suitable cement concrete foundation duly plastered and with anti vibration pads. 450 lpm at 35 m Head.

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required.

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required: 2 way-100 mm dia M.S. Pipe

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585, 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30 Mtr.

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required: S.S 304

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with Gl wire, rivets etc. conforming to IS 636 (type-A) as required: Stainless Steel (Grade 304)

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Stainless steel

SITC of Hose Box of 18 SWG M.S Sheet with glass fronted door to accommodate 2 nos. RRL Hose & 1 nos. SS Branch Pipe with nozzel. (Extrernal/Internal)

SITC of Automatic panel of terrace pump suitable for 5 HP tarrace pump.

Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 16 Sq. mm 4 Core

SITC of cast iron Ball Valve 25mm dia.

Supply and fixing of self illuminating glow exit signage Size 400x150 mm.

SITC of Digital Chairman Unit : Base Unit -Frequency Response: 40Hz-16KHz; Sensitivity: -44 dB:2dB ; Supports Discussion & Video; Chairman Base Unit should have Talk button along with Priority Button; The talk button should have built-in Dual colour LED light, Green colour indicating its On & Red colour indicating to talk. Connectivity : Daisy Chain connection with Loop In Loop Out; Connection : 8 Pin; Base Dimension :120( L ) mm x 85mm (W) x 20mm(H);Microphone : It should have detachable Microphone ; Polar Pattern – Cardioid; LED Light – Should have Red Ring LED Light Indicating Microphone ON/Off; Microphone Length - 420mm or more MAKE - ATDSC/ Work Pro/ Clockaudio

SITC of Digital Delegate Unit : Base Unit -Frequency Response: 40Hz-16KHz; Sensitivity: -44 dB:2dB ; Supports Discussion & Video; Delegate Base Unit should have Talk button; The talk button should have built-in Dual colour LED light, Green colour indicating its On & Red colour indicating to talk Connectivity : Daisy Chain connection with Loop In Loop Out; Connection : 8 Pin; Base Dimension :120( L ) mm x 85mm (W) x 20mm(H);Microphone : It should have detachable Microphone ; Polar Pattern – Cardioid; LED Light – Should have Red Ring LED Light Indicating Microphone ON/Off; Microphone Length - 420mm or more MAKE - ATDSC/ Work Pro/ Clockaudio

SITC of Digital Audio Controller : The main unit of the portable digital conference system can support 60 units of microphone. ; It support 250 Microphones with extension power unit.; Equipped with four groups or 8p-DIN interface for system connecting.; Modes : Discuss mode, Free mode, FIFO mode (1-9),Limit mode (1-9) ; 9 Microphones can be on at a time. First In First Out ; The working mode is displayed on LCD screen. ; Look At Me – Speaker tracking compatible with camera and processor; Connection: 8PIN x 3 plugs for Microphone ; 8 PIN x1 socket for system connection; RCA : 4 x RCA Port; RJ 45 x 1; XLR Port x 1MAKE - ATDSC/ Work Pro/ Clockaudio

SITC of Amplifier: Power Output 300W Max., 250W RMS at 10% THD, 220W RMS at 5% THD, Output Regulation 2 dB, no load to full load at 1kHz, Input Channels 6 X Mic. 0.65mV/4.7k Ohms , 2 X Aux 100mV/470k Ohms, Frequency Response 50-15,000Hz ±3dB, Signal to Noise Ratio 60dB, Tone Controls Bass ±10dB at 100Hz, Treble±10dB at 10KHz, Outputs Line: 200mV/600 Ohms, 1V/1k Ohms, Speaker Output 4 Ohms, 8 Ohms & 100V, Digital Player MP3 Player with USB, SD Card & Bluetooth, Power Supply AC: 220-240V 50/60Hz , DC: 12V, Power Consumption : AC : 250VA DC : 4A, Power Consumption AC : 250VA DC : 4A, Consist of USB Pen drive Port SD Card Plug and Play, Compatible with Radio & Bluetooth, EQ & Recording, 5 Channels Microphone Inputs, 2 Channels Aux Inputs, 1 Channel Line Output. 100V Constant Voltage Output and 4Ω\ 8 Ω \16 Ω Resistance Output. MAKE - ATDSC/ Work Pro/ EAW

SITC of Speaker: Should have Two-way speaker configuration , Power handling: 200W peak (50W RMS) or more, 5.25” woofer and ½” titanium-laminate tweeter or better; Frequency range (-10 dB): 80 Hz – 20kHz or better ; Frequency response (+/-3 dB): 100 Hz – 18kHz or better ; Power Capacity: 150W or more ; Sensitivity: 87 dB SPL, 1 W 1 m (3.3 ft) or better; Maximum SPL: 108 dB continuous, 114 dB peak or more; Directivity Factor (Q): 6.0 or better ;Directivity Index (DI): 7.8 dB or better ; Nominal Impedance: 8 ohms or better ; Crossover Frequency: 4.2 kHz or more ; Overload Protection LF Driver: 135mm (5.25 in) low frequency loudspeaker or better ; HF Driver: 19 mm (.75 in) polycarbonate dome tweeter or better ; Enclosure Material: Polypropylene Structural Foam Should have All-weather construction for the outdoors; Easy setup ; Input Connectors: Spring – loaded terminals MAKE - ATDSC/ Work Pro/ EAW

SITC of Equipment Rack, 18U - 19" Racks with Standard accessories for Packaging of Audio Video devices, with a rigid base Frame Structure made of metal, Complete with cable -entry cut-outs at the rear, fitted with a cover plate. Removable Front and rear Panel are provided . Castors and levelling legs. Top cover with Fan Housing Unit. Make : Comrack/Economic/Vallrack or Equivalent

SITC of Digital Conference Microphone Cable, Speaker Cables, Patch Cables and connector for Installation and connectoin of Supplied Conference and PA system complete in all respect.

SITC of 86" Interactive Flat Panel : Display Panel Size: 86", Backlight :DLED; Resolution : 3840×2160 Pixels - 4K UHD & 4K UI; Brightness : 500cd/㎡; Dot Pitch : 0.4935x0.4935mm; Contrast Ratio: 4000:1(Typ.); Response : Time 8ms; Aspect Ratio : 16:9; Touch Screen :IR ; Touch Points : 20Points; Frame Frequency :60Hz; Angle of View :178° ; Ageing :≥50,000 H ; Display Cover : Anti-glare with 9H Hardness (Anti Scratch); CPU : ARM Cortex-A55x4, @1.5GHz; GPU Core: Quad-core, GPU: Mali-G52 MP2(2EE); RAM: 4GB; ROM : 32GB; System Version: Android11.0; Interfaces HDMI ports: Front:- 3 in 2 Out; USB Ports : 1 x Touch USB, 2 x USB 3.0 , Type C Ports: 2 Other Ports : 1 x VGA IN, 1 x DP IN, 1 x Audio In, 1 x Audio Out , 1 x RJ45 In ,1 x RJ45 Out ; Speaker: 2 X 20W; AC Input ×1; Power Switch ×1; Dual Camera Support. MAKE- ATDSC/ViewSonic/ Delta

SITC of 65” panel having resolution of 3840 x 2160( UHD ), brightness 400 Cd /m Sq, Contrast 1000000:1 Audio out 10W + 10W , Signature features : Vertical Setup, Fail Over, Play Via URL, NTP Server Setting, CISCO Certificated, Crestron Connected (Network Based Control), DPM (Digital Power management), Time scheduler, RTC (Real Time Clock), NTP sync timer, BEACON, webOS6.0, Embedded CM (contents manager), Embedded GM (Group manager) Smart Features :Web Browser, Pre-loaded App, SDP Server compatibility, Mood Display, Soft AP, WiFi (Version) (802.11ac), Screen Share (Miracast), Smart Share, Bluetooth Audio Playback, HDMI-ARC (ARC, HDMI2), Key Features : PDM / Installer Menu, One Channel Map, IP Channel Manager, External Speaker Out (Int Variable/Fixed, 3.5mm, Stereo, Single ended Type) Make : LG / Samsung / Panasonic/Sony.

SITC of 55” smart TV 4K UHD contrast ration 1300:1, resolution: 3840 X 2160, Brightness: 400nit, Panel type:IPS speaker system: 20W, Opertaing system: webOS 6.0, voice control: supports voice assistants, Connectivity: Wi-Fi, Bluetooth 5.0, Ethernet, and multiple HDMI ports, support HDR 10 and HLG, high compatiblity with professional AV controls with adjustable stand,. Make: LG/Samsung/Panasonic/ Sony.

SITC of OPS: PROCESSOR : Core i5 1O21Ou / 1035G7, Generation: 10th Generation , Max Resolution: 4k@60Hz, MEMORY: 8GB DDR4 Expandable upto 32GB, GRAPHICS : On Board Intel® UHD Graphics , LAN : 10/100/1000 Gigabit LAN , Prime Storage : 256GB SSD M.2, Second Storage : (optional) , USB: 7 USB PORTS (4X USB 3.0 + 1 TYPE C PORT, MEMORY Slots : 2 SLOTS , AUDIO: AUDIO IN + OUT , DISPLAY PORT : DP + HDMI , Wi-Fi : Dual Wi-Fi (2.4Ghz and 5Ghz), BlueTooth : BT 4.0, OS: Windows / UBANTU 19.04 or ABOVE. MAKE - ATDSC/Dell/Lenovo

SITC of USB based PTZ Camera with min. 20X optical zoom, 16X digital zoom, f=5.5~~110mm iris (F1.6~~F3.5), 3.3°(tele)–54.7° wide viewing angle, 1/2.8" or better CMOS sensor, 2.07 MP, supporting SDI formats 1080P60/50/30/25/59.94/29.97, 1080i60/50/59.94, 720P50/30/25/59.94/29.97; min. illumination 0.5 Lux, 2D & 3D DNR, auto/manual/one push white balance (3000K–7000K), electronic shutter auto/manual, auto/manual/one push focus, BLC On/Off, WDR with dynamic adjustment, video adjustments (brightness, color, saturation, contrast, sharpness, B/W, gamma), SNR >55dB, interfaces USB 2.0, USB 3.0, LAN, RS232, HDMI, audio in; H.265/H.264 compression, VISCA/Pelco-D/Pelco-P protocols, baud rate 11520/9600/4800/2400, LAN port with RTSP/RTMP/ONVIF/ GB28181, pan rotation +170°, tilt -30°~~+90°, pan speed 0.1~~60°/sec, tilt speed 0.1\~30°/sec, preset pan 60°/sec, tilt 30°/sec, 255 presets; Make – ATDSC/Adonis/Vaddio.

SITC of Digital Signal Data Cable, HDMI Cable, Power Cable, Connector Connection Patch Plates/Boxes, Patch Cables and connector for Installation and connectoin of Supplied Display Unit and PTZ Camera complete in all respect.

SITC of 1 in 8 out HDMI distribution amplifier. Make Kramer/ Aten/ Manhaddan

M/s Subhash Builders (BID ID -5581919)