COMPREHENSIVE MAINTENANCE OF SMQS TMQS OF BR WORKS AT NANDINI COMPLEX PUSHP VIHAR AREA AND PUMP HOUSE IN DOMESTIC AREA AT AF STN BHISIANA

Amount

Taking down Cement Plaster including raking out Joints, hacking for Key, scrubbing down with Water and removing Debris, etc. to Outside MD/AF Land, complete all as specified and as directed.

M&L for 15mm thick cement plaster in CM (1:4) on fair faces of brick or concrete wall surfaces and finishing the surface even and fair and Preparation of new plastered wall surface and applying two coat of cement base paint over one coat of primer with chalk whitening on external wall surface etc. complete all as specified and as directed.

M&L for 15mm thick cement plaster in CM (1:6) on fair faces of brick or concrete wall surfaces and finishing the surface even and fair and Preparation of new plastered wall surface and applying two coat of oil bound distemper over one coat of primer complete all as specified and directed.

M&L for 15mm thick cement plaster in CM (1:6) on fair faces of brick or concrete wall surfaces and finishing the surface even and fair and Preparation of new plastered wall surface and applying three coat of white wash complete all as specified and directed.

M&L for 5 mm thick cement plaster 1:3 on fair faces of brick work or concrete surfaces in ceiling and finishing the surface even and smooth (without using extra cement) etc including applying three coats of white wash and after preparation of plastered surfaces complete all as specified and directed.

M&L Rough Cast Plaster on Brick Walls consisting Under Coat of Cement and Sand Mortar 1:3 not less than 10mm thick and while it is still in Plastic state the Rough Cast Mixture consisting of Crushed Stone or Fine Gravel mixed with Coarse Sand and Cement in the Ratio 1:1:1 shall be applied and finish Even, complete all as specified and as directed.

Dismantling Stone slabs and tiles of any description or thickness laid bedded & pointed in any mortar in floors/walls, aprons complete all as specified.

M&L for 20-25 mm thick kota stone floor tiles machine cut (square/recatangular) etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, including 15mm thick screed bed n CM (1:6) as in screed bed or bedding and demolition of existing floor finishes complete as all specified and directed by Engr-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), and rubbish off the premises complete all as specified.

M&L for Non Skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc. including 15mm thick screed bed in CM (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match copmplete. NOTE : Cost of Cement Screed Bed shall deem to be include in the Quoted Unit Rate.

M&L for Glazed ceramic coloured tiles in vertical surface 350x250x7 mm / 450x300x7mm thick including 10mm thick cement plaster in CM 1:3 set and jointed in neat cement slurry and pointed in white or colour cement to match complete. NOTE : Cost of Rendering shall deem to be include in the Quoted Unit Rate.

M&L for Non Skid coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM (1:4) for laying floor finishes complete all as specified. NOTE : Cost of Cement Screed Bed shall deem to be include in the Quoted Unit Rate.

M&L for Non Skid coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, on vertical surfaces as in skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick cement plaster in CM 1:3 to receive vertical tiles complete all as specified. NOTE : Cost of Rendering shall deem to be include in the Quoted Unit Rate.

M&L for Non Skid coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM (1:4) for laying floor finishes complete all as specified. NOTE : Cost of Cement Screed Bed shall deem to be include in the Quoted Unit Rate.

M&L for Non Skid coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, on vertical surfaces as in skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick cement plaster in CM 1:3 to receive vertical tiles complete all as specified. NOTE : Cost of Rendering shall deem to be include in the Quoted Unit Rate.

M&L for 12-15mm thick green marble slab flooring including 15mm thick screed bed in Cement Mortar (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab one side bullnosed including dismentling existing slab/stone etc complete. NOTE : Cost of Cement Screed Bed shall deem to be include in the Quoted Unit Rate.

M&l for kota stone floor tiles 20-25 mm thick, machine cut (square/rectangular) as in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, including 10 mm thick cement plaster in Cement Mortar (1:3)for receiving tile to wall complete as all specified and directed by Engr-in-Charge. NOTE : Cost of Rendering shall deem to be include in the Quoted Unit Rate.

Demolition Cement Concrete (un-reinforced) of any description in Ground Floors, Pavings, etc. not exc. 150mm thickness (above or below Ground Level) and removing debris, etc. to Outside MD/AF Land, complete all as specified and as directed.

M&L for Cement Concrete 1:3:6, type C-1 (20mm graded stone aggregate) 75mm thick as in Plinth Protection, finishing Cement Concrete surface Even and Smooth without using Extra Cement, including making joints 12mm wide upto total depth of concrete at every 3.00 metre interval and every change of direction, complete all as specified and as directed.

M&L for Cement concrete type, B1, 1:2:4 (20mm graded stone aggregate) 25mm thick including finishing the surfaces even and fair to receive floor finishes complete all as specified and directed by Engineer in Charge.

Taking up or down Steel Tubing 15mm bore (dia) with Fittings/ Connections, segregating Serviceable Pipes and Fittings/ Connections and keep in Safe Custody for re-use, complete all as specified and as directed.

Taking up or down Steel Tubing 20mm bore (dia) with Fittings/ Connections, segregating Serviceable Pipes and Fittings/ Connections and keep in Safe Custody for re-use, complete all as specified and as directed.

Refixing Steel Tubing 15mm bore (dia) and Fittings in new or old position, (Serviceable Pipes and Fittings obtained from Item No. 21 here-in-before) after cleaning inner and outer surfaces of Pipes by using of Wire Brush including provision of new GI Fittings (as required), complete all as specified and as directed.

Taking down Chowkat or Frame of any description (without taking off Shutter from the Frame) not exc. 1.50 Square Metre Each, complete all as specified and as directed.

Refixing Steel Tubing 20mm bore (dia) and Fittings in new or old position, (Serviceable Pipes and Fittings obtained from Item No. 20 here-in-before) after cleaning inner and outer surfaces of Pipes by using of Wire Brush including provision of new GI Fittings (as required), complete all as specified and as directed.

Taking down Shutter of any description exc 1.00 Square Metre and not exc. 2.00 Square Metre Each and Refixing in the Same Opening, after resecuring or easing and adjusting, etc., complete all as specified and as directed.

Taking down chowkats & shutters without taking off shutters from the frame, size of opening exc. 1.50 sqm but not exc 4 sqm each complete all as specified and as directed.

S&F Pressed Steel Frame of size 105x60mm using 1.25mm thick Mild Steel Sheets for Doors with One or More Rebates including necessary Fixing Lugs, Hinges, Lock Strike Plate, etc., complete all as specified and as directed.

S&F Pressed Steel Frame for door of size 125x60mm using 1.25mm thick Mild Steel Sheets for Doors with One or More Rebates including necessary Fixing Lugs, Hinges, Lock Strike Plate, etc., complete all as specified and as directed.

M&L Cement Concrete 1:3:6 (20mm graded stone aggregate) as in Filling Back side of Pressed Steel Frame, complete all as specified and as directed.

S&F Factory made Solid PVC Door Frame of size 50x47mm made out of 5.0mm thick plain colour PVC Sheet reinforced with Mild Steel Square Tube and fixing in opening as per Specification and Drawing of MES Schedule Part-II, complete all as specified and as directed.

S&F Factory Made Solid Panel PVC Door Shutter 30mm thick (Style) Plain Colour (Ivory Shade) consisting of Frame made out of Mild Steel Tubes for Top & Bottom Rails of Mild Steel Frame shall be covered with Heat Moulded Wood Grain PVC ‘C’ Channel having a PVC Sheet Strip of 20mm width Stuck inside with Solvent Cement for Stiles and Wood Grain PVC Sheets for Top Rail Lock Rail & Bottom Rail on either side and as gap insert for Top Rail & Bottom Rail, Panelling of Wood Grain PVC Sheet to be fitted in the Mild Steel Frame welded/sealed to the Stiles & Rails with suitable 5.0mm thick x 15mm wide PVC Sheet Beading used inside Stiles and Rails and decorative PVC Beading of 10mmx10mm (90°) and jointed together with Solvent Cement and fixing in the Frame at Site, complete all as specified and as directed.

S&F Aluminium Anodised Butt Hinge 100mm long (weight not less than 90 Gram) and fixed, complete all as specified and as directed.

S&F Aluminium Handle 125mm long (weight not less than 60 Gram), Cast type, anodised, complete all as specified and as directed.

S&F Aluminium Anodised Tower Bolt 125mm long (weight not less than 160 Gram), Extruded Section, complete all as specified and as directed.

M&L Factory Made Panelled Shutter 35mm thick of Second Class Hardwood with Panels of 12mm thick Veneered Particle Board medium density wood with commercial face veneered both side or panel of 9mm BWP commercial ply and fitted to Chowkats, having size of Rail and Stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated, complete all as specified and as directed.

M&L for Factory made Glazed and Skeleton Shutter 35mm thick of Second Class Hardwood prepared to receive Gauge/Glass (without Sash Bars) fixed with mitred beeds supplied and fitted to Chowkat and securing Glass of thickness 3mm, Gauge, etc. sizes of Members of Shutter as specified in SSR Part-I, Section-8, Clause 8.24(a), complete all as specified and as directed.

S&F Hasp and staple safety type aluminium powder coated with mild steel pin inculding bolt to hinge plate and fix with screws 150 mm size of hasps and staples.complete all as specified and directed by Engineer in Charge.

S&F Aluminium Barrel Tower Bolt 200mm long (weight not less than 180 Gram), Extruded Section, complete all as specified and as directed.

S&F Aluminium Handle 150mm long (weight not less than 120 Gram), Cast type, anodised, complete all as specified and as directed.

S&F Mild Steel Sliding Door Bolts having length of Bolt 300mm, plate type, stove enamelled black, with bright Bolt not less than 12mm dia with and including a minimum of 6 Bolts and Nuts, 4 on Bolt Plate and 2 on Staple Plate and fixed, complete all as specified and as directed.

Taking down shutters of any description exc 1 sqm but n exc 2 sqm each complete all as specified and as directed.

S&F in repair Mild Steel 300mm, Ordinary Rat Tail Rod pattern Springs including Roller and Roller Plate and fixed, complete all as specified and as directed.

S&F Floor Door Stopper 140mm in size, Aluminum alloy Body and Tongue with Hard Drawn Steel Spring (weight not less than 90 Gram), complete all as specified and as directed.

Supply and fixing factory made box type steel window with glazed shutter (outside) and gauged shutter (inner side), Box type section used in outer frame, sutter frame and centre frame shall be ERW section of 18 gauge. As per sample kept in GE office which can be seen by the tenderer, includes one MS handle 100mm long, 02 Nos MS tower bolt 150 mm long and 01 Nos peg stay arrangement in each shutter also pin holes to be provided @ 300mm C/C for supporting glass with GI clips wire in case of glazed shutter and 02 Nos of pintal Hinges 75mm long, 12mm dia with one of the hinge spot welded with frame and other with shutter for each openable shutter shall be provided and 04 Nos flat iron hold fast of size 25x3mm of length 250mm to 300mm long shall be welded with each window (all the iron mongry shall be ISI marked), including provn of MS guard bars of 10 mm square size minimum @ 100mm C/C spacing, equally divided welded with the help of MS fillet of size 25x3mm complete all as per sample and as directed. The Rates includes 4mm thick plain sheet glass in glazed shutter and galvanized wire mess 0.56 mm nominal dia of wire and average width of aperture 1.18 mm in gauzed shutter and 02 coats of synthetic enamel paint over a coat of zinc chrome primer including preparation of new surfaces complete all as specified and as directed. Note: 02 Nos window in each quarter to be facilitated with space for desert cooler with openable/ detachable shutter and guard bars as per sample.

S&F in repairs box type steel ventilator glazed & gauged factory made with side hung shutters including box type hinges with steel handle and steel peg stay, necessary grills and guard bars and 4mm thick froasted glass including taking down existing window including applying two coat of synthetic enamel paint over a coat of red oxide primer and making good the disturbed portion with PCC or Plaster and painting the surface to match with the existing surface complete all as specified and directed by Engineer in Charge.

M&L preparing New or previously untreated Wooden Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a Pink Primer, complete all as specified and as directed.

Hacking out old broken Glass (any thickness, size, quality or description) from Metal Frames, glazed with putty or fixed with beads, complete all as specified and as directed.

S&F Sheet Glass 3.0mm thick, Ordinary quality and glazing with Oil Putty in Square not exc. 0.50 Sqm in Each Pane, complete all as specified and as directed.

S&F Figured Glass 4.0mm thick, Pin Head type and glazing with Oil Putty in Square not exc. 0.50 Sqm in Each Pane, complete all as specified and as directed.

S&F Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples, etc. and fixed complete all as specified and as directed.

S&F in repairs Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples, etc. and fixed complete all as specified and as directed.

S&F in repairs Cast Iron (Sand Cast) 75mm bore (dia) Soil, Waste and Ventilating Pipe, in any length with Cement Joints, with or without Ears, Fixed to Walls , complete all as specified and as directed.

S&F in repairs Cast Iron (Sand Cast) 100mm bore (dia) Soil, Waste and Ventilating Pipe, in any length with Cement Joints, with or without Ears, Fixed to walls , complete all as specified and as directed.

S&F in repairs 75 mm bore CI Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches fitted with oval access door, complete all as specified and as directed.

S&F in repairs100mm bore CI Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches fitted with oval access door , complete all as specified and as directed.

S&F in repairs 75 mm dia CI bends (any radius), diminishing pieces or tapers provided with access door , complete all as specified and as directed.

S&F in repairs 100 mm dia CI bends (any radius), diminishing pieces or tapers provided with access door , complete all as specified and as directed by Engineer in Charge.

S&F in repair 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement, complete all as specified and as directed by Engineer in Charge.

Supply & laying Steel Water Tubing 15mm bore (dia), Galvanised, ‘medium grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other situation, complete all as specified and as directed by Engineer in Charge.

Supply & laying Steel Water Tubing 20mm bore (dia), Galvanised, ‘medium grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other situation, complete all as specified and as directed by Engineer in Charge.

M&L for cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good to facings where required and pointing in cement mortar 1:3 , cutting not exc 10 cm girth complete all as specified and as directed by Engineer in Charge.

S&F in repairs 100 mm bore Traps 'P' or 'S' any radius etc. jointing with Solvent Cement , complete all as specified and as directed by Engineer in Charge.

S&F in repairs Vitreous China White Squatting Pan of size 580x440mm, 'Orissa' Pattern with Integral Foot Rests, ‘P’ or ‘S’ Trap, providing Joints between Flush Pipe and Socket of WC Pan, Cones, India Rubber (nozzles of WC Pan) incluiding provision of Lime Concrete Bedding and Making Good to Floor/distrubed surfaces, complete all as specified and as directed by Engineer in Charge.

S&F in repairs Vitreous China White Wash Down Water Closet Pan (Pedestal Pattern) with Trap including Seat Cover and Fixing Bolts and Making Good to Floor/ disturbed surfaces, complete all as specified and as directed by Engineer in Charge.

S&F Flush pipe of polyethylene of low or high density of PVC, 32 mm dia and make a proper connection with water closet and low level cistern with leak proof and fixed in repair, complete all as specified and as directed by Engineer in Charge.

S&F in repairs PVC Flushing Cistern 10 Litre capacity White, Low Level, Valveless, Syphonic Action type with Inlet, Ball Valve, Float and Handle, a pair of Cast Iron Brackets Erecting Stand duly painted including cutting and pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3, complete all as specified and as directed by Engineer in Charge.

S&F in repairs Vitreous China Wash Hand Basin 550x400mm in size, White (Flat Back) with Brass Chromium Plated Waste Fitting 32mm bore (dia) and PVC Waste Pipe 32mm bore (dia) including a Pair of Cast Iron Brackets Brackets Erecting Stand duly painted including cutting and pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 complete all as specified and as directed by Engineer in Charge.

S&F in repairs Pillar Tap 15mm bore (dia), Cast Copper Alloy with Capstan Heads, Chromium Plated, screwed down high pressure, with Long screwed Shanks and Fly-nuts, screwed for Iron Pipe , complete all as specified and as directed by Engineer in Charge.

S&F in repairs 15 mm bore Stop Valve fancy type chromium plated with long shank and cup (concealed type),cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union, complete all as specified and as directed by Engineer in Charge.

S&F in repairs for stop/ Angle valves, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipes or for union, complete all as specified and as directed by Engineer in Charge.

S&F in repairs PVC Connection Pipe 15mm size and 45 Cm in length with Adopter Nuts of PVC, complete all as specified and as directed by Engineer in Charge.

S&F in repairs Tubular Towel Rail 20mm dia, Brass Chromium Plated, D-type, 60 Cm long between Flanges with Bracket (one Pair) , complete all as specified and as directed by Engineer in Charge.

S&F in repairs Bib Tap 15mm bore (dia), Cast Copper alloy, Fancy type Chromium Plated with Crutch or Butterfly Handle, screwed down, screwed for Iron Pipe or for Brass Ferrule and Chromium Plated Wall Flange, complete all as specified and as directed by Engineer in Charge.

S&F in repairs Chromium Plated Shower Rose with Shower Arm 100mm, Swival Joint including fixing to Steel Pipe , complete all as specified and as directed by Engineer in Charge.

Dismantling Structural Steel or Mild Steel Work of any description not otherwise provided for, complete all as specified and as directed by Engineer in Charge.

S&F for Rolled Mild steel Joist, channel, angle, or tee sections, fixed independently, without connecting Plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) suitable for cooler stand etc complete all as specified and as directed by Engineer in Charge.

S&F in repairs Sink with Drainage Board made of Stainless Steel l.0mm thick Kitchen or Laboratory Overall size 495x420mm having Bowl size 410x330x160mm with Plugs, Washers and Wastes, etc. including bedding in Cement Mortar to dwarf Wall or including fixing Cantilever Brackets and connecting Union to Pipe , complete all as specified and as directed by Engineer in Charge.

Demolition Brick work built in Cement Mortar and in any Position including all Quoins, Arches and Pillars, etc., complete all as specified and as directed by Engineer in Charge.

M&L Brick Work with Sub-Class ‘B’ Bricks (Old Size Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:6, complete all as specified and as directed by Engineer in Charge.

S&F in repair PVC (SWR) 110mm bore (dia) Soil, Waste and Ventilating Pipe, single socketed, in any length with PVC Joints, with or without Ears, fixed to Walls , complete all as specified and as directed by Engineer in Charge.

S&F in repair PVC (SWR) 110mm bore (dia) Soil, Waste and Ventilating Pipe, single socketed, in any length with PVC Joints, with or without Ears, laid in Floors , complete all as specified and as directed by Engineer in Charge.

S&F in repair PVC (SWR) 75mm bore (dia) Soil, Waste and Ventilating Pipe, single socketed, in any length with PVC Joints, with or without Ears, fixed to Walls, complete all as specified and as directed by Engineer in Charge.

S&F in repair PVC (SWR) 75mm bore (dia) Soil, Waste and Ventilating Pipe, single socketed, in any length with PVC Joints, with or without Ears, laid in Floors , complete all as specified and as directed by Engineer in Charge.

S&F in repair PVC (SWR) Bend 110mm bore (dia), any radius etc. jointing with Solvent Cement , complete all as specified and as directed.

S&F in repair PVC (SWR) Bend 75mm bore (dia), any radius etc. jointing with Solvent Cement , complete all as specified and as directed by Engineer in Charge.

M&L Rotational Moulded Polyethene Water Storage Tank 500 Litre Capacity, Cylindrical, Vertical with Closed Top, 3 layered, hoisted and fixed in Position all as specified in MES Schedule including dismantling / lowering down unserviceable Water Storage Tanks,complete all as specified and as directed by Engineer in Charge.

M&L Rotational Moulded Polyethene Water Storage Tank 1000 Litre Capacity, Cylindrical, Vertical with Closed Top, 3 layered, hoisted and fixed in Position all as specified in MES Schedule including dismantling / lowering down unserviceable Water Storage Tanks, complete all as specified and as directed by Engineer in Charge.

S&F Ball Valve 20mm dia (minimum Weight 210 Gram), high pressure of PTMT with epoxy coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe , complete all as specified and as directed by Engineer in Charge.

S&F in repair Gun Metal Globe/Gate Valve 20mm bore (dia) with Iron Wheel Head, screwed both Ends for Iron Pipe, complete all as specified and as directed by Engineer in Charge.

S&F in repair Ball Valve 20mm dia (minimum Weight 210 Gram), high pressure of PTMT with epoxy coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe , complete all as specified and as directed by Engineer in Charge.

M&L for Removing of bushes upto 10 cm dia trunk, grass from roof top, racking out joints/pointing to brick tiles laid flat and flush pointing with 1:3 cement mortar compound, complete all as specified and as directed by Engineer in Charge.

S&F in repairs Mild Steel curtain rod 20mm dia PVC coated with fixing brackets and ends cap (latoo) complete all as specified and as directed by Engineer in Charge.

M&L for Providing, cement concrete type B1 1:2:4 (20mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges, roof padding complete all as specified and as directed by Engineer in Charge.

S&F 5mm thick termite proof, water proof and fire retartant plain PVC sheet jointed together & fixed on back side of Cupboard frame using solvent cement adhesive complete all as specified and directed by Engr-in-charge.

S&F 30 to 50mm wide and 5 mm thick laminated PVC leeping in front of the cupboard to be edge bonded using on the edges etc complete all as specified and as directed by Engineer in Charge.

S&F Continous Piano hinges by making adequate hole in 18 mm board from inside and fixed to cupoard shutter and frame by screw, Bright finish width of Flaps when open 40mm, complete all as specified and as directed by Engineer in Charge.

S&F Stainless Steel Silver chrome Door Handle 125mm long, screwed from inside the Shutter complete all as specified and as directed by Engineer in Charge.

S&F Magnetic Door Catcher medium grade to hold approx 1000 mm opening Cupborad Door complete all as specified and as directed by Engineer in Charge.

S&F 40 mm wide telescopic drawer channel fitted to celuka Ply Board and stainless steel basket for smooth movement, complete all as specified and as directed by Engineer in Charge.

Dismantling Boarding of any description including hardware fitting, fixed in any position with nails etc complete all as specified and as directed by Engineer in Charge.

S&F Factory made PVC cupboard sides, top & bottom frame (Each side measured Seperately) , 30mm thick (hollow) with a wall thickness of 5mm made out of extruded 5mm thick plain/printed/prelam PVC sheet reinforced with 19mm x 19mm MS square tubes of 19 gauge thickness throughout the frame and mitre cut at two corners and jointed with two numbers 150mm long brackets of 10mm x 10mm square tubes and cupboard frame shall be fixed to the wall using 65/100mm long MS screws through the frame by using PVC fasteners. A minimum of 4 nos of screw to be provided for each vertical member and minimum of 2 nos of srew to be provided horizontal member etc complete as per manufacter's instructions and all as specified and directed. Note : Making good the disturbed side plastering and Painting with existing colour (Distemper/OBD) included in the item.

S&F Factory made PVC cupboard shutter of 30 mm thick consisting of frame made out of MS tubes of 19 gauge thickness and size 19mm x 19mm covered with panneling of 5mm plain plus 5mm thick prelaminated PVC sheet fitted in the MS frame and sealed to the front stiles and rails which should having 20mm x15mm wide PVC biding and attached to back stiles and rails (which should have a 5mm 45 degree bend portion as beding) and decorative PVC beding is used on the front side of pannel externally impart perfect finish to the shutter and joint together with solvent cement adhesive complete all as specified and as directed by Engineer in Charge.

S&F Factory made PVC drawer of required size (Each side measured Seperately) constructed by joining two nos 5mm thick plain PVC sheet at the sides and bottom joint together with solvent cement adhesive complete all as specified and as directed by Engineer in Charge.

S&F Factory made PVC centre partition shelfs of 25mm thickness consisting of MS Frame made out of MS tube of 19 guage thickness and size of 15x15mm inserted all around the hollow profile section and insert 15mmx15mm MS tube in the centre of this section and liped with 10mm (5mm x2) thick plain PVC sheet at the top and bottom and 20mm wide and 15mm thick on sides using solvent cement adhesive complete all as specified and as directed by Engineer in Charge.

S&F 5mm thick termite proof, water proof and fire retardant laminated PVC sheet jointed together at front side of Cupboard drawer frame using solvent cement adhesive complete all as specified and directed by Engr-in-charge.

M&L for Brick work with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in 1:4 cement mortar complete all as specified and as directed by Engineer in Charge.

M&L for preparation of new steel surfaces of any description not otherwise described over 10cm width or grith and applying two coats of synthetic enamel paint over a coat of red oxide primer exposed to view surfaces complete all as specified and as directed by Engineer in Charge.

RAKESH KUMAR GARG & CO.

classic estate developers

Aman Enterprises