Hosur Plug and Play

Amount

Earth work excavation for foundation in all kinds of soils and subsoils and to the required depth as may be directed except hard rock requiring blasting but inclusive of shoring, strutting and bailing out water wherever necessary, refilling the sides of foundation and basement with excavated earth in layers of 15cm thick well rammed, consolidated and depositing the surplus earth in places shown with an initial lead of 10 meters and initial lift of 2 meters and clearing, levelling the site etc., complete. (As per TNBP No. 23 & 24)

Earth work excavation for foundation and depositing on bank in Soft disintegrated rock, laterite, soft rock or kankar, not requiring blasting with initial lead of 10 m & lift of 2m to 3m and clearing, levelling the site etc., complete. (As per TNBP No. 23 & 24)

Providing Pre-construction Antitermite Treatment to soil adjacent and under the building foundation, plinth periphery of the building by application of chemicals as per IS 6313 Part I to IV in stages to suit the progress of work etc., complete.

Supplying and filling in foundation and basement with Stone Dust in layers, not exceeding 150mm thickness well rammed, watered and consolidated complying with relevant standard specification etc., complete. (As per TNBP No. 24 & 25)

Plain Cement Concrete 1:5:10 (One cement, five of M Sand and ten of coarse aggregate) using 40mm gauge hard broken stone jelly for foundation inclusive of dewatering if found necessary, shoring, strutting, side shuttering, ramming, curing and laid in layers not more than 15cm thick etc., complete complying with standard specification. (As per TNBP No. 28)

Supplying and erecting Centering for sides and soffits including necessary supports and strutting upto 3.29m height as detailed below with all cross bracings using Mild Steel Sheets of size 90 x 60cm and 10 BG stiffened with Welded Mild Steel Angle of size 25mm x 25mm x 3mm for boarding laid over silver oak joists of size 10cm x 6.50cm spaced at about 90cm centre to centre and supported by Casurina Props of 10cm to 13cm dia spaced at not more than 75cm centre to centre etc., complete complying with standard specification. (Payment for centering shall be given after the concrete is laid). (As per TNBP No. 86 & 86A)

For Plane Surfaces such as column footings, column pedastals, plinth beams, grade beams, staircase steps and other similar woks etc.

For Plane Surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams and other similar woks etc.

For Plane Surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing and other similar woks etc.

For Plane Surfaces such as vertical slab, side slab of boxing, vertical drops, facia, vertical wall and other similar woks etc.

Providing additional strutting to centering for all floors RCC slabs of Plane Surface of every additional 1m height or part thereof but not less than 30cm over an initial 3m height from floor level using casurina props of 10cm to 13cm dia including cross bracing etc., complete complying with standard specification and as directed by the department officers.

Ready Mixed Cement Concrete of M30 grade including pumping in all floors with minimum cement content of 400 kg per cubic meter of ordinary portland cement with 100mm slump using HRWRA Ad-mix, M Sand, 10-12mm and 20mm gauge HB stone jelly for all RCC items of works excluding centering, shuttering and also cost of reinforcement grill in position but including laying, curing and finishing etc., complete and also fixing fixtures like fan clamps in the RCC floor / roof slab wherever necessary etc., complete complying with standard specifications and as directed by the departmental officers.(As per TNBP No. 30)

For Foundation and Basement

For Stilt Floor

For First Floor

For Second Floor

For Third Floor

For Fourth Floor

For Terrace Floor

Supplying, fabricating and placing Reinforcement Steel of high yeild strength ribbed bar of various diameter and grade confirming to IS1786 of reinforced concrete work. The work including decoiling, straightening, cutting, bending, fabricating and placing in position at all levels and floors including lead and lift according to drawings, specifications, etc complete. Supply and use of 18Gauge black annealed binding wire double fold to tie the bars in position, chairs pins, space bars, unauthorised laps which will not be measured separately neither for payment nor for reconsilation and providing precast cement / pvc cover blocks for main reinforcement to ensure specified cover and as directed. Steel and binding wire will be procured by the contractor at his own cost. (As per TNBP No. 30 & 86)

Brick Work in Cement Mortar 1:6 (One of cement and six of M Sand) using Fly Ash Bricks of size 230 x 110 x 75mm including curing etc., complete complying with standard specification and as directed by the SIDCO Engineers. (As per TNBP No. 31)

For Foundation and Basement

For Stilt Floor

For First Floor

For Second Floor

For Third Floor

For Fourth Floor

For Terrace Floor

Brick Partition Wall 11.50cm thick using Fly Ash Bricks of size 230 x 110 x 75mm in Cement Mortar 1:3 (One of cement and three of M Sand) including fixing hoop iron reinforcement if found necessary, laying, finishing and curing etc., complete complying with standard specification and as directed by the SIDCO Engineers. (Hoop Iron Reinforcement will be measured and paid separately) (As per TNBP No. 31C)

For First Floor

For Second Floor

For Third Floor

For Fourth Floor

Supplying and fixing WPC Door of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black Colour) covered with over all the edges of frame and shutter the shutter will be provided with Spig multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown Colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Supplying and fixing Mild Steel Grills as per the design approved to doors, windows or ventilators using MS flats or square rods for inner and outer members including cost of steel & angles and labour for fixing in position etc., complete complying with standard specification and as directed by the TANSIDCO Engineers. (As per TNBP No. 86A)

Paving the floor with AntiSkid Colour Designed Ceramic Tiles of size 305 x 305 x 6mm in all floors laid over 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One of cement and three of M Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg/ sqm etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by the Executive Engineer before use on works) (As per TNBP No. 39A)

Providing Granolithic Floor Finish of 40mm thick with PCC 1:2:4 (One of cement, two of M Sand and four of coarse aggregate) using 10 - 12 mm Gauge Hard Broken Stone Jelly in all floors including labour charges by finishing the top by smooth rubbing etc., complete complying with standard specification. (As per TNBP No. 39A)

Paving the floor with Pre-polished Concrete Anti-Skid Step Tiles of 20mm thick of approved quality and colour laid in all floors using cement mortar 1:3 (One of cement and three of M Sand) base mortar including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.4 Kg/ sqm etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by the Executive Engineer before use on works) (As per TNBP No. 39A)

Paving the floor with Joint Free Rectified Glazed Ceramic Flooring Tiles of size 305 x 305 x 8mm of approved colour, shade and quality in all floors laid in Cement Mortar 1:3 (One of cement and three of M Sand) of 20mm thick and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works). (As per TNBP No. 39A)

Supplying and fixing Granite Slab (Jet Black) of size 18mm to 20mm thick with super fine polished machine cut edges in partition of size 1200mm x 600mm between the urinals in all floors laid over a Cement Mortar 1:3 (One of cement and three of M Sand) 20mm thick, fixing the slab with required cement slurry, laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with matching colouring pigments including labour charges etc., complete complying with standard specification. (The granite slab and other material should be got approved by Executive Engineer before use on work).

Special Ceiling Plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One of cement and three of M Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing etc., at all floors complying with standard specification and as directed by the SIDCO Engineers. (As per TNBP No. 56 & 57)

Plastering with Cement Mortar 1:5 (One of cement and five of M Sand) of 12mm thick including centering, strutting, finishing and curing etc complete complying with standard specification. (As per TNBP No. 56 & 57)

Plastering with Cement Mortar 1:3 (One of cement and three of M Sand) 20mm thick in all floors mixed with water proofing compound at 2% by weight of cement used, including centering, strutting, finishing and curing etc complete complying with standard specification. (As per TNBP No. 56 & 57)

White Washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder, fevicol type gum, brushes, scaffolding charges etc., complete complying with standard specification and as directed by the SIDCO Engineers. (As per TNBP No. 63)

Painting the New Walls with two coats of approved interior Plastic Emulsion Paint of approved quality and shade at all floors in two coats over one coat of primer to give an even shade including scaffolding, curing etc., complete. The rate including all materials for putty, primer, emulsion paint and all labour charges and as directed by the SIDCO Engineers (The quality and colour of the emulsion, putty and primer shall be got approved from the Executive Engineer before use on work). (As per TNBP No. 66A)

Painting the New Walls with two coats of approved weather shield exterior Emulsion Paint at all floors in addition to one coat of approved primer cement paint over cement plastered wall surfaces etc., including cost of Emulsion paint, putty, brushes, watering, curing etc., all complete in all respects and as directed by the SIDCO Engineers (Paints and its shade shall be got approved from the Executive Engineer before using). (As per TNBP No. 66A)

Painting New Iron Work with two coats of best approved first quality and colour of Synthetic Enamel Paint over the existing red oxide priming coat in all floors etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on work). (As per TNBP No. 66)

Manufacturing, Supplying and Fixing of Stainless Steel Hand Rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Weathering Course in brick jelly lime concrete using broken brick jelly of size 40mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers. (As per TNBP No. 46B)

Finishing the top of roof with one course of Pressed Tiles of size 230mm x 230 mm x 20mm of approved quality laid in Cement Mortar 1:3 (One of cement and three of M Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers. (As per TNBP No. 39A)

Providing and fixing of Aluminium Composite Panel (ACP) 4 sided having 50 x 25 x 1.50mm frame work vertical and horizontals out of specially designed extruded sections withstand wind pressure of 180 Kg/sq.m and fabricated fixed at all level elevation and heights. The extruded section cutting and fixing required space extruded section shall be of 6063 and alloy of BSH 9 confirming T is – 63400 rate shall included to fix the main frame with necessary clamps, fasteners, bolt nuts etc. The main frame of extruded section shall be of 22843 & 22739 (H9) grade conforming to BS 4174 (or) IS 8147. Rate shall included 4mm thick ACP sheet (0.25 + 3.5 + 0.25) alstrong or equivalent fixing with spacer tape and the ACP sheet bounded with special type structural sealant of dow corning 789 or equivalent in dust free conditions the gaps between ACP sheet to be filed with whether sealant and backer rod or 12mm foam sheet to ensure water and air tightness in all complete complying with standard specification as directed by the departmental officer

Supplying and Erecting Pull and Push Type Rolling Shutter of manually operated up to 8 sqm. area with ISI make of approved size and section using 18 GI sheet. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc., complete.

Supplying and fixing in position 110mm dia PVC Rain Water Down Fall Pipes of best approved finolex (or) equivalent with ISI monogram having a pressure of 4 Kg / Sq cm including cost of necessary PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including neat finishing. The rate shall be inclusive of cast of removable cast iron gratings. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipeline in addition to those for more than 3.0m pipe length etc., complete complying with standard specification. (As per TNBP No. 107)

Supplying and fixing in position best quality PVC Soil Waste Pipes of best approved finolex (or) equivalent with ISI monogram having a pressure of 6 Kg / Sq cm and providing leak proof joints including fixing to the wall with special PVC / MS clamps etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever necessary and making good the dismantled portion to the original condition including testing for leakages etc., complete complying with standard specification and as directed by the SIDCO Engineers. (The PVC Pipes shall be got approved by the Executive Engineer before use on work).(As per TNBP No. 107)

110mm dia PVC Soil Waste Pipe

75mm dia PVC Soil Waste Pipe

Supplying and fixing in position of 32mm Gun Metal Gate Valve (Heavy Duty) of first quality and variety including shellac, thread ball and labour charges etc., complete complying with standard specifications. The valves to be used on work shall be got approved by the Executive Engineer before use on work.

Supply and fixing PVC Specials for sanitary arrangements of approved finolex or equivalent with ISI monogram conforming to relevant standard specifications etc., complete.

160mm dia PVC Elbow

110mm dia PVC Elbow

75mm dia PVC Elbow

160mm dia PVC Door Elbow

110mm dia PVC Door Elbow

75mm dia PVC Door Elbow

160mm dia PVC Tee

110mm dia PVC Tee

75mm dia PVC Tee

Supply and fixing PVC Specials for sanitary arrangements of approved finolex or equivalent with ISI monogram conforming to relevant standard specifications etc., complete.

160mm dia PVC Tee with single door

110mm dia PVC Tee with single door

75mm dia PVC Tee with single door

160mm dia PVC Bend

110mm dia PVC Bend

75mm dia PVC Bend

160mm dia PVC "Y"

110mm dia PVC "Y"

75mm dia PVC "Y"

Supply and fixing PVC Specials for sanitary arrangements of approved finolex or equivalent with ISI monogram conforming to relevant standard specifications etc., complete.

160mm dia PVC "Y" with single door

110mm dia PVC "Y" with single door

75mm dia PVC "Y" with single door

Supplying and fixing Brass Chromium Plated Screw Down Tap of 15 / 12mm dia (Heavy Type) of approved quality and make conforming to ISS and providing leak proof joints with thread ball and shellac etc., including cost of fittings, labour for fixing, cutting and threading wherever necessary etc., complete and as directed by the SIDCO Engineers. (As per TNBP No. 39A)

Supplying and fixing Brass Chromium Plated Pillar Tap of 15 / 12mm dia (Heavy Type) of approved quality and make conforming to ISS and providing leak proof joints with thread ball and shellac etc. including cost of fittings, labour for fixing, cutting and threading wherever necessary etc., complete and as directed by the SIDCO Engineers. (As per TNBP No. 39A)

Supplying, laying and jointing of following dia PVC Pipe having a working pressure of 10 Kg / Sq.cm and specials of approved finolex or equivalent with ISI monogram. The rate includes the necessary earth work excavation in ordinary soil, soft disintegrated rock & dense medium rock requiring blasting, laying the pipes to proper grade & alignment upto 2.00m depth, jointing with PVC couplers & required specials as directed with heavy duty solvent cement joints and testing to the required pressure, the conveyance of water upto 1km lead for filling during testing including cost of pipe, fixing of necessary specials, jointing materials, labour for jointing the specials and refilling the trench as before after the pipes are laid as directed by the SIDCO Engineers etc., complete. Approval of the Executive Engineer should be obtained for the pipes before use on work. (Rate excluding the cost of specials) (As per TNBP No. 107)

25mm dia PVC Pipe

32mm dia PVC Pipe

Supplying and fixing in position best quality of approved make Colour Glazed Earthernware WASH HAND BASIN (without pedastal) of size 550 x 400mm with a pair of cast iron brackets including cost of 15mm diameters brass chromium plated pillar tap, 32mm diameter C.P Waste, 32mm diameter PVC Waste Pipe with rubber plug and chain, 15mm diameter gun metal wheel valve, 15mm diameter brass nipple, 15mm diameter nylon connectin etc., including fixing the wash hand basin in the wall in position with pair of C.I.Brackets with teak wood plugs and screws and giving necessary water supply connection and painting the brackets with two coats of paint over a priming coat of anti-corrosive paint including testing for leakage etc., complete complying with standard specifications and as directed by the SIDCO Engineers. (The wash hand basin and specials should be got approved by the SIDCO Engineers before use on work). (As per TNBP No. 102 & 103)

Supplying and fixing in position White Glazed Model Floor Mounted European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works) (As per TNBP No. 102 & 103)

Supplying and fixing in position of best Indian Make White Lipped Mouth Porcelain Flat Back Urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI Pipe, 32mm dia Bell Mouth PVC connection and Waste Pipe, 15mm dia GI Pipe of required length, 15mm dia GM Wheel Valve, 15mm dia Brass Nipple 2 Nos., and fixing the Urinals in position with necessary TW Plugs, Clamps, Screws etc., including dismantling masonry and re-doing the same to the original condition etc., including painting the pipe with two coats of best quality approved Synthetic Enamel Paint over one coat of Red Oxide Primer and checked without any leakage etc., complete complying with standard specifications and as directed by the SIDCO Engineers. (The Urinal should be got approved by the Executive Engineer before use on work) (As per TNBP No. 102 & 103)

Supplying and fixing in position of Cast Iron Nahini / Floor Trap of size 100 x 75mm with stainless steel grating of approved brand and quality fixed over a bed of Brick Jelly Lime Concrete 1:2:5 (One of lime, two of M Sand and five of 40mm size Brick Jelly) and finished with Cement Mortar 1:3 (One of cement and three of M Sand) including dismantling masonry works wherever found necessary and making good the damaged portions to the original condition giving connections to the pipe etc., complete and as directed by the SIDCO Engineers. (The Cast Iron Nahini / Floor Trap with stainless steel grating should be got approved by the Executive Engineer before use on work). (As per TNBP No. 39A)

Supplying and fixing Stone Ware Gully Trap of size 150 x 100mm with cast iron double gratings over a bed of 150mm thick brick jelly cement concrete 1:3:6 (One of cement, three of M Sand and six of brick jelly) using 40mm size brick jelly and PCC 1:3:6 (One of cement, three of M Sand and six of brick jelly) using 20mm size brick jelly including labour charges etc., complete and as directed by the SIDCO Engineers. (The Stone Ware Gully Trap with cast iron double gratings should be got approved by the Executive Engineer before use on work).

Construction of Inspection Chamber of size 600mm x 600mm x 1100mm internal dimensions as per drawing including necessary earth work excavation in all kinds of soils, Stone Dust filling, PCC 1:5:10 (one of cement, five of M Sand and ten of aggregate) using 40mm gauge hard broken stone jelly, brick work in CM 1:6 (One of cement and six of M Sand) using fly ash brick work of size 230 x 110 x 75mm, plastering with CM 1:3 (One of cement and three of M Sand) 20mm thick & plastering with CM 1:5 (One of cement and five of M Sand) 12mm thick for inside, outside, top & bottom and SFR cover of size 600mm x 600mm including cost of all materials, fixing & labours etc., complete and as directed by the TANSIDCO Engineers.

LT METERING PANELS (Detailed Specifications is enclosed in Annexure I of tender documents and it will be included in the agreement) LT METERING PANEL-(1, 2, 3, 4, 5, 6, 7,8) Incomer: 400 A TP+N FUSE 1 set - RYB LED type indicating lamps 1 set - Control MCB with Neutral link. Bus bar: 1 set - 400A, 36kA, 415V, TPN Copper busbars, interconnections with colour coded heat shrinkable sleeves and SMC Busbar supports. Outgoings: 63A TPN FUSE - 9Nos 63A TPN 36kA MCCB with ON,OFF,TRIP - 9Nos METERING : 40-60A KWHR - 9Nos(Space provision for EB Meter)

LT METERING PANEL-9 Incomer: 400 A TP+N FUSE 1 set - RYB LED type indicating lamps 1 set - Control MCB with Neutral link. Bus bar: 1 set - 400A, 36kA, 415V, TPN Copper busbars, interconnections with colour coded heat shrinkable sleeves and SMC Busbar supports. Outgoings: 63A TPN FUSE - 6Nos 63A TPN 36kA MCCB with ON,OFF,TRIP - 6Nos METERING : 40-60A KWHR - 6Nos(Space provision for EB Meter)

LT METERING PANEL-10 CT Metering Panel supply of CT metering panel for 3 comporment panel type ( indoor ) copper busbar 25 x 10 tpn hylam sheet, 6mm 500 x 500 - 2 nos test terminal block riesin type current transformer 200 /5 class - 0.5 - 3 nos 40 x 10 bolt nut drill bit - 5 mm wire 2.5 sqmm, r-y-b -n each 12 mtrs 2.5 sqmm pin lugs - 30 nos 2.5 sqmm ring lugs - 30 nos, 4 sqmm pin lugs - 20 nos metering glass 40 mm insulator.

UTILITY PANEL Incomer: 2Nos. 400A,4P MCCB 36kA with E / M interlock (motorised MCCB). Metering for Incomer: 2 No. Multifunction meter (KWH+KW+A+V+F+MD with RS - 485 port, MODBUS)(96 x 96mm size) 2set - 400A ,5VA, CL 0.5, CT's for metering. 2 set - RYB LED type indicating lamps. 2 set - Control MCB with Neutral link. 2 set-ON,OFF,TRIP Bus bar:1 set - 400A, 4Wire, 36kA, 415V, TPN Copper busbars, interconnections with colour coded heat shrinkable sleeves and SMC Busbar supports. Outgoings: 2Nos. 125A TPN MCCB 36kA with ON,OFF,TRIP 2Nos. 100A TPN MCCB 36kA with ON,OFF,TRIP 6Nos. 63A TPN MCCB 36kA with ON,OFF,TRIP 1No. 32A TPN MCCB 36kA with ON,OFF,TRIP

COMMON LIGHTING AND POWER PANEL Incomer: 1 Nos. 100A,TPN MCCB 36kA Metering for Incomer: 1 No. Multifunction meter (KWH+KW+A+V+F+MD with RS - 485 port, MODBUS)(96 x 96mm size) 1 set - 100A ,5VA, CL 0.5, CT's for metering. 1 set - RYB LED type indicating lamps. 1 set - Control MCB with Neutral link. 1 set - ON,OFF,TRIP Bus bar: 1 set - 100A, 4Wire, 36KA, 415V, TPN Copper busbars, interconnections with colour coded heat shrinkable sleeves and SMC Busbar supports. Outgoings: 8 Nos-40A TPN MCCB 36kA with ON,OFF,TRIP 6 Nos - 40A DB MCB 10kA

LIFT PANEL Incomer: 1Nos. 125A,TPN MCCB 36kA Metering for Incomer: 1No. Multifunction meter (KWH+KW+A+V+F+MD with RS - 485 port, MODBUS)(96 x 96mm size) 1set - 125A ,5VA, CL 0.5, CT's for metering. 1set - RYB LED type indicating lamps. 1 set - Control MCB with Neutral link. 1 set-ON,OFF,TRIP Bus bar: 1 set - 125A, 4Wire, 36kA, 415V, TPN copper busbars, interconnections with colour coded heat shrinkable sleeves and SMC Busbar supports. Outgoings: 6Nos. 63A TPN MCCB 36kA with ON,OFF,TRIP

EMERGENCY UPS OUTGOING PANEL Incomer: 1 No. 32A,TP+2N MCCB 36kA Metering for Incomer: 1 No. Multifunction meter (KWH+KW+A+V+F+MD with RS - 485 port, MODBUS)(96 x 96mm size) 1 set - 32A ,5VA, CL 0.5, CT's for metering. 1 set - RYB LED type indicating lamps. 1 set - Control MCB with Neutral link. 1 set-ON,OFF,TRIP Bus bar: 1 set - 32A, 4Wire, 36KA, 415V, TP+2N Copper busbars, interconnections with colour coded heat shrinkable sleeves and SMC Busbar supports. Outgoings: 5 Nos. 25A TP+2N MCCB 36kA with ON,OFF,TRIP

400 A TPN FSU With Fuse Enclosure box for EB

DISTRIBUTION BOARDS Supply, installation, testing & Commissioning of the following Floor DB's to achieve the IK rating of 09 and all as per IEC61439-1&3, double door construction, powder coated with approved shade and partitions to segregate phases, 7segment if three phase incomer DB. Approved lockable covers with padlocking arrangement for each phase, recessed in wall or surface mounted with angle iron frame. All DBs shall have double type of the following description:

LIGHTING AND POWER DISTRIBUTION BOARD Supply and fixing of 7 segment 4 way 40A TPN MCB sheet steel distribution board (Higher end) with metal door cover surface type fitted with busbars and neutral links with sub incomer and single phase MCB outgoings . Seperate 4 way provision for accomodating one no. 4 pole incoming MCB and another seperate 4 way provision for accomodating one no. 4 pole RCCB/ELCB (totally 8 ways in one segment) SubIncomer: seperate provision for MCB / Isolators/RCCB/ELCB for sub incomers in 3 segments Outgoings: 3 x 4 ways in each segment, provision for MCB (totally 12 nos.) with lable holder and provison for taking up cable with the following on wall with earth connection. Incomer: 1No.Four Pole 40A 10kA MCB Sub Incomer : 3 Nos. 40A, 30mA, Double Pole RCCB/ELCB Outgoing : 12 Nos. Single Pole 6A to 32A,10kA MCB

LIGHTING AND POWER DISTRIBUTION BOARD Supply and fixing of 7 segment 6 way 40A TPN MCB sheet steel distribution board (Higher end) with metal door cover surface type fitted with busbars and neutral links with sub incomer and single phase MCB outgoings . Seperate 6 way provision for accomodating one no. 4 pole incoming MCB and another seperate 4 way provision for accomodating one no. 4 pole RCCB/ELCB (totally 8 ways in one segment) SubIncomer: seperate provision for MCB / Isolators/RCCB/ELCB for sub incomers in 3 segments Outgoings: 3 x 6 ways in each segment, provision for MCB (totally 18 nos.) with lable holder and provison for taking up cable with the following on wall with earth connection. Incomer: 1No.Four Pole 40A 10kA MCB Sub Incomer : 3 Nos. 40A, 30mA, Double Pole RCCB/ELCB Outgoing : 18 Nos. Single Pole 6A to 32A,10kA MCB

EMERG. LIGHTING DISTRIBUTION BOARD Supply and fixing of 7 segment 6 way 40A TPN MCB sheet steel distribution board (Higher end) with metal door cover surface type fitted with busbars and neutral links with sub incomer and single phase MCB outgoings . Seperate 6 way provision for accomodating one no. 4 pole incoming MCB and another seperate 4 way provision for accomodating one no. 4 pole RCCB/ELCB (totally 8 ways in one segment) SubIncomer: seperate provision for MCB / Isolators/RCCB/ELCB for sub incomers in 3 segments Outgoings: 3 x 6 ways in each segment, provision for MCB (totally 18 nos.) with lable holder and provison for taking up cable with the following on wall with earth connection. Incomer: 1No.Four Pole 25A 10kA MCB Sub Incomer : 3 Nos. 25A, 30mA, Double Pole RCCB/ELCB Outgoing : 18 Nos. Single Pole 6A to 32A,10kA MCB

POWER DISTRIBUTION BOARD Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) on wall with earth connection only. Higher End Incomer: 1No. Double Pole 32A,10kA MCB Sub incomer 1No.Double Pole 25A 30mA, RCCB/ELCB Outgoing : 4 Nos. Double Pole 25A,10kA MCB

EXTRA LOW VOLTAGE DISTRIBUTION BOARD Supply and fixing of 7 segment 4 way 40A TPN MCB sheet steel distribution board (Higher end) with metal door cover surface type fitted with busbars and neutral links with sub incomer and single phase MCB outgoings . Seperate 4 way provision for accomodating one no. 4 pole incoming MCB and another seperate 4 way provision for accomodating one no. 4 pole RCCB/ELCB (totally 8 ways in one segment) SubIncomer: seperate provision for MCB / Isolators/RCCB/ELCB for sub incomers in 3 segments Outgoings: 3 x 4 ways in each segment, provision for MCB (totally 18 nos.) with lable holder and provison for taking up cable with the following on wall with earth connection. Incomer: 1No.Four Pole 25A 10kA MCB Sub Incomer : 3 Nos. 25A, 30mA, Double Pole RCCB/ELCB Outgoing : 12 Nos. Single Pole 6A to 32A,10kA MCB

CAR CHARGING DISTRIBUTION BOARD Supply, fixing, testing and commissioning of single/double door type compartmental 4way Three phase Vertical MCB DB - IP 42 comprising of the following : Incomer: 1No. 63A FP MCB 1 No. 63A, 100mA, FP RCCB/ELCB Outgoing : 12 Nos. 20A to 32A, SP MCB

DB FOR MODULES Supply and fixing of 8 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with wall with earth connection only. Higher End following : 8 way VTPN DB Incomer: 1No. 63A FP MCB 1 No. 63A, 100mA, FP RCCB/ELCB Outgoing : 4 Nos. 40A, TP MCB 12 Nos. 20A to 32A, SP MCB

PHE DB Supply and fixing of 8 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with wall with earth connection only. Higher End 8 way VTPN DB Incoming-63A 4P 10kA MCB - 1 No. 1 No. 63A, 100mA, FP RCCB/ELCB Outgoing:6A to 32A TP MCB - 6No`s 6A to 32A SP MCB - 6No`s

LIFT DB Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) on wall with earth connection only. (Higher End) 4 way VTPN MCB DB Incoming- 1No Four Pole 63A,10kA MCB, 1No Four Pole 63A 100mA RCCB/ELCB, Outgoing: 2Nos Triple Pole 32A,10kA MCB, 6Nos Single Pole 6A to 32A,10kA MCB.

Supply and fixing of 4P 32A MCB in suitable sheet steel enclosure with connected complete accessories.

Design, manufacture,warranty, transportation, supply, erection, testing and commissioning and integration of 10kVA size Conventional UPS with isloation transformer, Uninterrupted Power Supply (UPS), NUMERIC – HPI 10KVA (3Ph-3Ph) FMI(FLOOR MOUNTABLE WITH ISOLATION TRANSFORMER ) 240VDC Online Double Conversion UPS System & MS rack for housing the batteries along with interconnection cable & SNMP card. with 2yrs warrenty

Design, manufacture, transportation, supply, erection, testing and commissioning of Sealed Maintenance Free (VRLA) Battery Bank for10kVA Uninterrupted Power Supply (UPS) 12V - 150Ah - 20 Nos Battery for 90 minutes Back up with 2 yrs warrenty

DIESEL GENERATOR SET: (160 kVA) (Detailed Specifications is enclosed in Annexure I of tender documents and it will be included in the agreement) Supply, installation, testing & commissioning of 160 KVA with AMF panel 3 phase, 415V (Prime & Standby) Silent (Acoustic proof) diesel generating set wit local isolating control with adapter box suitable for terminating Al / Cu. armoured XLPE cable. along with Auto Controller, day oil fuel tank DG set including vibration mounts, base frame, 2 set of hardware Batteries, Engine control panel with accessories first fill of lube oil residential silencer, flexible connection bellow / expansion joints, etc.. complete and with all associated equipment / work as per specifications.

Supply, fixing & installing exhaust pipe fabricated out of 5 mm thick MS plate and all fixing accessories and hardware's. The exhaust pipes shall be insulated with 100 mm thick LRB mineral wool (140 kg/cu.m) insulation wrapped in chicken mesh and clad with 28 Gauge Aluminium sheet rate including flexible connection bellow / expansion joints, Y Piece with coupling sets etc. The scope of works also include of the aviation lamp in the exhaust stack & necessary lighting arrestor. 6"mm dia MS Exhaust pipe complete with insulation as above, flange, hardware with suitable bends painting in approved color. The scope of works also include 2" thick Thermal insulation with Aluminium cladding

MS support for exhaust pipe, residential silencer and miscellaneous supports and frames etc

Supply and clamping of 4C x240 sq.mm. XLPE LTUG Al armoured cable on post /on wall/Tray with MS clamps

Supply and Laying of 4C x 240 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and clamping of 3.5C x70 sq.mm. XLPE LTUG Al armoured cable on post /on wall/Tray with MS clamps

Supply and clamping of 3.5C x50 sq.mm. XLPE LTUG Al armoured cable on post /on wall/Tray with MS clamps

Supply and clamping of 4x25 sq.mm. XLPE LTUG Al armoured cable on post /on wall/Tray with MS clamp

Supply and clamping of 4x16 sq.mm.XLPE LTUG Al armoured cable on post /on wall/Tray with MS clamps

Supply and clamping of 2Cx16 sq.mm. XLPE LTUG Al armoured cable on post /on wall/Tray with MS clamps

Supply and clamping of 4C x 6 sq.mm PVC Cu. Flexible cable on post /on wall/Tray with MS clamp

Supply and clamping of 1C x 6 sq.mm PVC Cu. Flexible cable on post /on wall/Tray with MS clamp

Supply and clamping of 3x2.5 sq.mm. XLPE LTUG Cu armoured cable on post /on wall/Tray with MS clamps

Supply and clamping of 3x1.5 sq.mm. XLPE LTUG Cu armoured cable on post /on wall/Tray with MS clamps

Supply and fixing of brass cable gland with termination for 4CX240sq.mm. PVC armoured LTUG cable with earth connection

Supply and fixing of brass cable gland with termination for 3.5CX70sq.mm. XLPE armoured LTUG cable with earth connection

Supply and fixing of brass cable gland with termination for 3.5CX50sq.mm. XLPE armoured LTUG cable with earth connection

Supply and fixing of brass cable gland with termination for 4CX25sq.mm. XLPE armoured LTUG cable with earth connection

Supply and fixing of brass cable gland with termination for 4CX16sq.mm. XLPE armoured LTUG cable with earth connection

Supply and fixing of brass cable gland with termination for 2CX16sq.mm. XLPE armoured LTUG cable with earth connection

Earth pit excavation, electrode installation with common salt/ char coal/ bentonite for chemical earthing ( to achieve the required earth resistance value), inspection chamber with removable CI / RCC covers inclusive of all civil works. The distance between two earth electrodes should be 3000mm. While measuring the earth resistance, it should be possible to easily disconnect the bolts with hand tools. Earth pits permanent identification marks are to be provided both inside and out side. Dedicated earth pits electrodes connecting insulated conductors should be run UG conduits. All the welded joints should be coated with bitumen to avoid rusting. All the fasteners required like PVC pipes, bolts,nuts, locking serrated/ flat/spring washers are included in the scope. The vendor shall include the cost for equipment to earth pit with necessary civil works(Were as required). Supply and fixing of Copper Plate Earth Electrode – Copper Plate 600 X 600 X 3 mm Thick, Hot Dip Galvanized Pipe 40 mm NB 48 mm OD 3 Mtrs long, 25 X 3 mm Copper Strip 2 Runs ( 2850 mm ) suitable bolt, nut, washer ( SS ), Copper Clamp, Funnel ( with Assemble ) with Salt and Charcoal 50 Kg Each, 0.45 m X 0.45 m X 0.6 m Manhole Cover For DG Neutral earthing

HDGI Plate Earth Electrode – HDGI 600 X 600 X 6 mm Thick, Hot Dip Galvanized Pipe 40 mm NB 48 mm OD 3 Mtrs long, 25 X 3 mm HDGI Strip 2 Runs ( 2850 mm ) suitable bolt, nut, washer ( SS ), HDGI Clamp, Funnel ( with Assemble ) Salt and Charcoal 50 Kg Each, 0.45 m X 0.45 m X 0.6 m Manhole Cover

Supplying and laying 8 SWG Hard drawn CU wire including connection/ termination etc. as required.

Supply and run of 25mm x 6mm GI Flat Down Condutor with necessary clamps / supports on wall / floor / ground for earth connection

Supply and run of 50mm x 6mm copper flat with necessary clamps / supports on wall / floor / ground for earth connection

Supply and run of 25mm x 6mm copper flat with necessary clamps / supports on wall / floor / ground for earth connection

1C 6Sq.mm Cu Flexible Cable (Green colour) with terminations on both the ends

Supply and run of 25mm x 3mm copper flat with necessary clamps / supports on wall / floor / ground for earth connection

Supply and fixing of Profile design Cable Ladder with horizontal & vertical bends, reducers, Tee's,Cross over, supports, brackets and other accessories as required confirming to IS/ IEC-61537.The Cable Ladder shall be made of 1.6mm thick.The cable Ladder shall be Pregalvanized for corrosion protection confirming to DIN EN 10346 / ISO 1461 .The cable ladder should be tested for safe working load and cable ladder shall be supplied in standard length.

750 x 100mm x height x 2mm thick Ladder tray

600 x 100mm height x 2mm thick Ladder tray

450 x 75mm height x 1.6mm thick Ladder tray

300 x 75mm height x 1.6mm Ladder tray

Supply and fixing of Profile design Perforated Cable tray with horizontal & vertical bends, reducers, Tee's, cross over , suitable supports and brackets and other accessories as required confirming to IS/IEC-61537. The Tray shall be galvanized for corrosion protection as per ISO 1461.The trays should be tested for a safe working load and cable perforated shall be supplied in standard length.

450mm wide x 75mm height x 1.6mm Perforated tray

300mm wide x 75mm height x 1.6mm Perforated tray

200mm wide x 50mm height x 1.6mm Perforated tray

100mm wide x 50mm height x 1.6mm Perforated tray

Supply and fixing of 1 no.6/16 A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box ( GI ) in flush with wall with connections. Lower End

Supply and run of 2 of 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable heavy gauge MS coundit pipe on wall and ceiling with continous earth wire connection of 14 SWG TC wire with painting of suitable colour

Supply and fixing of 1 no.6A two module 5 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI) in flush with wall with connections. Lower End

Supply, Installation, Testing and Commissioning of "Switched Industrial Socket Outlets (with & without Plugs)" as per the requirements below. It shall be Weatherproof rated to IP44.Provide permanent circuit identification for every point/Socket. Provide 8 SWG Copper Wire earthing from primary earth flat to all power sockets and equipment earthing points. 1No. 32A 2P+E 1phase Interlock type socket with plug top with locking facility with MCB DP ( IP 44)

Supply and fixing of 20A DP plug and socket in sheet enclosure with 32A DP MCB in flush with wall with earth connection (For AC Plug)

Supply & Installation Of 3 star 1.5 TR split type Air-Conditioner with 4 KVA capacity Automatic Voltage Stabilizer with time delay relay and with MS stand for fixing outdoor unit.

Supply and laying of 3/8" or 5/8" copper pipe (Extra beyond 3 metres supplied with AC unit)

Supply and Run of 2 of 2.5 sq.mm. (36/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable gauge MS conduit pipe on wall and ceiling with continuous earth wire connection of 14 SWG TC wire with painting of suitable colour.

Supply and run of 2 of 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable gauge MS conduit pipe on wall and ceiling with continuous earth wire connection of 14 SWG TC wire with painting of suitable colour

Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete without provision of hole in the wall

Supply and fixing of 1200mm (48") AC ceiling fan complete with stepped electronic 300W regulator with 300mm down rod on the existing clamp.

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with Module GI switch box in flush wall with 6A one way module switch with module front plate with painting of Suitable colour with continuous earth wire connection of 14SWG TC wire for Open MS conduit Light point ( 5 points / Coil) Lower End

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with Module GI switch box in flush wall with 6A one way module switch with module front plate with painting of Suitable colour with continuous earth wire connection of 14 SWG TC wire for Open MS conduit Fan point with 2 Module fan step regulator( 5 points / Coil) Lower End

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with Module GI switch box in flush wall with 6A one way module switch with module front plate with painting of Suitable colour with continuous earth wire connection of 14 SWG TC wire for Open MS conduit Light point / fan point (for electronic regulator) ( 6 points / Coil) Lower End

Power Wiring with 3R x 2.5 sq.mm. PVC insulated single core unsheathed copper conductor cable of 1100V grade on 25mm dia MS conduit on wall and ceiling / floor with MS accessories for lighting circuits.

Supply and fixing of 4' 18W to 20W LED Tube in suitable general purpose fitting with connection complete

Supply, fixing of 10W LED Aviation Light luminaires made of Die-cast aluminum housing with Red polycarbonate dome for better illumination, Integral driver, 302Nos.x 5mm LEDs incorporated, Ingress Protection : IP65, life of LED 50000 burning hours with surge protection and protection against short circuit

Supply, fixing of 10W LED Bulkhead Luminaire, Luminaire shall meet IP66 and IK09 protection with connection complete

Supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete with 2core SMC fuse box with fuse unit, SMC terminals, glands & clamps, bolts/nuts on the existing post / on wall with PVC unsheathed copper leads with MS clamps and with painting.

Supply & Installation of rubber mats as per CEIG requirement's (As per CEIG norms/panel dimensions length and width to be provided)(2x1)meter - 5 Nos

Supply & Installation of shock treatment chart in English and Local language. Shock treatment chart to be printed & framed with glass front size 300 x 600.

Supply & Installation of first aid kit with wall mounting iron stand.

Design, Supply, Testing at works, Transportation to site, Erection, Testing at site, and commissioning of the following LT Kiosk suitable for 415 Volts, 3 Phase, 4 wire system, fabricated from 14 SWG CRCA sheet steel enclosure, single fronted, free standing, front hinged, rear removable, extendable on both sides, dust & vermin proof, cubicle type, floor mounted, undrilled gland plates at top/bottom, the panel board bottom of height should be minimum 600mm from FFL. complete with internal wiring, '400A 4P MCCB Type Isolator with Outdoor type IP-65 Weather proof Enclosure

Supply & Installation of 8mm dia Aluminium alloy Solid Round Conductor of material AlMgSi used in air termination and down conductor system . Cross sectional area of conductor should be 50 mm².

Supply & Installation of Nylon Conductor Holder for Parapet wall for holding 8 mm dia Aluminium alloy round Conductor.

Supply & Installation of Stainless steel 304 Grade Cross Connector for 8 mm dia Aluminium alloy round conductor & 10 mm Copper bonded conductor at cross/Tee junction.

Supply & Installation of Expansion Joint with connector to compensate the expansion and contraction of Solid Round Al. Conductor during temperature variations. Expansion Joint should be consider at every 20 mtr length of straight horizontal air termination and connected at both the end with use of straight connector conductor.

Supply & Installation of Aluminium Straight conductor connector for interconnecting 8mm Aluminium conductor to meets the requirement of IS/IEC 62305.

Supply & Installation of air termination rod of 2mtr length of material AlMgSi of diametre ø 16/10 mm crimped on both the ends (Tappered Type). The rod shall be mounted with stainless steel clamp and fixing accessories .

Supply & Installation of Stainless steel SS 304 Grade Folding Clamp as per sheet profile for 8 mm dia Aluminium alloy Solid Round Conductor for horizontal Air terminal above metal sheet to meet the requirements for IS/IEC 62305.

Supply & Installation of 8mm dia Aluminium alloy Solid Round Conductor of material AlMgSi used in air termination and down conductor system . Cross sectional area of conductor should be 50 mm².

Supply & Installation of Nylon Conductor Holder for Parapet wall for holding 8 mm dia Aluminium alloy round Conductor.

Supply & Installation of Aluminium Straight conductor connector for interconnecting 8mm Aluminium conductor to meets the requirement of IS/IEC 62305.

Supply & Installation of Lightning counter - LCD screen shows the number of lightning strikes, hour and date of lightning events Buttons enable TIME/DATE setting and log viewing. Replaceable battery, working life minimum five years, Complies with IEC/EN 62561-6.

Supply & Installation of Stainless Steel Test Joint round to round to interconnect between 8 mm Al. round conductor to 10 mm Copper conductor .

Supply & Installation of Rust resistant non corossive 10 mm dia Copper Bonded Steel round conductor used for Earth termination inside the concrete and soil.

Supply & Installation of Stainless steel SS 304 Grade Conductor Holder for fixing the 8 -10 mm dia round conductor on the wall .

Supply & Installation of Stainless steel 304 Grade Cross Connector for 8 mm dia Aluminium alloy round conductor & 10 mm Copper bonded conductor at cross/Tee junction.

Supply & Installation of Corrosion Bitumen tape for inside soil.

Supply & Installation of stainless steel Straight Connector for interconnecting 10 mm dia copper bonded round conductor at straight connection

Supply & Installation of CAPE make UL Listed Maintenance Free Copper bonded Earth rod of 3048mm length having the dia of 14.2 mm with copper coating thickness of 254 microns. The rod has been tested for Dimension, Marking, Tensile Strength, Salt mist, coating thickness, Electrical resistivity test before and after corrosion test as per IEC 62561-2 & UL 467. Earth enchancing mineral compound tested for leaching and TCLP with NABL accredited Lab as per IEC 62561-7 -25 kg Earth rod clamp made for terminating cable / flat conductor. Earth Chamber Inspection Pit made up of Plastic withstand load of 60kN

Design, Engineering, Supply, Fabrication, Erection, Testing, commissioning and handing over of 16 persons capacity passenger lift as per the following specifications.(Gearless lift without machine room) (Detailed Specifications is enclosed in Annexure I of tender documents and it will be included in the agreement)

Design, Engineering, Supply, Fabrication, Erection, Testing, commissioning and handing over of Goods Lift (2000 Kgs) as per the following specifications (Machine room less) (Detailed Specifications is enclosed in Annexure I of tender documents and it will be included in the agreement)

TERRACE BOOSTER PUMP Supply, erection, testing and commissioning of fire fighting application monoblock motor pumpset of 450 LPM at 20 metres head to develop 2.0 kg/sq.cm at the heightest and farthest hydrant point to make 10m water jet at the time of fire fighting emergency cicumstances, coupled with 3.75KW / 5HP rated three phase 415 volts, 50 Hz, 2880 rpm electrical motor, the pump with cast ron body, bronze impeller, rope gland packaging, suction size of 80 mm dia. delivery size of 65 mm dia, including the cost of foundaton concrete anti vibration mounting, rain safety hood and etc. complete as directed by the Departmental Officers

Supply, installation, testing and commissioning of CI D/F SLUICE VALVE WITH CAP/ WHEEL AS PER IS 14846/2000 PN 1.0 WITH ISI MARKING AND WITH 5 YEARS WARRANTY.

Manufacture, Supply and Delivery of DI D/F Slanted seat Swing Check Valve ( DI Non return valve). Body of ductile cast iron of Grade GGG 40 or equivalent grade and disc of ductile cast iron GGG 40 or equivalent grade with fully encapsulated EPDM rubber, where both faces can be used.Electrostatic epoxy powder/liquid coating (EP-P) inside and outside color blue RAL 5005 with minimum coating thickness of 250 microns. The EPDM rubber & Epoxy Powder should be approved by W 270. (EP-P) it is a resi-coat powder approved for drinking water application, applied through fusion bonding process by dipping the shot-blasted casted components heated up to 200 deg C). Face to face dimensions as per EN558-1, series 48 and flange connections as per EN 1092-2/IS 1538 and with 5 years warranty 65NB

Supplying,installation,testing and commissioning of G.M GATE VALVES AS PER IS BS 5154 and related IS Specifications as per with factory finish necessary flanges, Hot Dip GI nut, bolts & washers, painting, etc. Complete as per the technical specification.

Supply and installation of Cast Iron Y strainer (PN 10) with necessary flanges,gaskets,GI bolts,nut & washers with all complete. 80 NB

Supply, erection, testing and commissioning of following MS ‘C’ Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm including necessary fittings like MS flange of table ‘E’, elbows, reducers, gaskets, bolt, nuts with washers & joints as per standard method of arc welding, including one coat metal primer and two coat Post Office Red painting including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., complete as per standard specification and as directed by the SIDCO Officers. Make: JINDAL / EQUIVALENT. (Detailed Specifications is enclosed in Annexure I of tender documents and it will be included in the agreement)

100 NB - 5.4 mm Thick - Class C

80 NB - Class C

65 NB - Class C

50 NB - Class C

25 NB - Class C

Supply and fixing of Fire fighting application oblique type stainless steel Hydrant Valve of size 63mm dia with oblique type instantaneous coupling with rotating wheel to open and close the valve including MS flange of table “E”, bolts & nuts with washer as per IS 5290 at ring main around the building and wet riser inside the building including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the SIDCO Officers.

Supply, and fixing in position of Fire Fighting Application Hose of 63mm dia of 15 metres length binded by copper wire with 63mm dia stainless steel male and female instantaneous fire fighting special coupling as per IS 901 as directed by the SIDCO Officers. Near every hydrant points including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the SIDCO Officers.

Supply, and fixing in position of Fire Fighting Application 63mm dia stainless steel short length Branch Pipe with hexagonal type spray nozzle of 15mm (or) 20mm jet bore. Near every hydrant points including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., complete as per standard specification and as directed by the SIDCO Officers.

Supply of Fire Fighting Application MS Hose Box to keep two number of hoses and 1 No. of branch pipe with nozzle having proper glass window type double door with universe open key, painted inside white and outside Post Office Red. Near every hydrant point including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., complete as per standard specification and as directed by the SIDCO Officers.

Supply, installation of Fire Fighting Application 180 degree swinging type, hose reel drum with 20mm dia braided thermoplastic hose of 30 metres long, so as to extend to necessary distance by self rolling spindle wheel including necessary 20mm dia ball valve and open and close spray nozzle, warm clip, etc., as per the standard pattern of any reputed make at every floor nearer to hydrant valve, including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary., etc., complete as per standard specification and as directed by the SIDCO Officers.

Supply, erection, testing and commissioning of Fire Fighting 4 Way Fire Brigade Inlet with necessary gun metal 63mm dia non return spring shutter arrangements, so that to control one way flow at the time of emergency water supply by fire and rescue service fire engine entry including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., complete as per standard specification and as directed by the SIDCO Officers.

Supply, erection, testing and commissioning of Air Release Valve of 20mm dia, so as to release airlock in 100mm dia MS pipe at top most wet riser, including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., complete as per standard specification and as directed by the SIDCO Officers. Make: KARTAR /EQUIVALENT.

Supply, erection, testing and commissioning of Pressure Gauge with 0 to 14 kg. range of reputed make with necessary valve, milling thread MS coupling fixed at delivery pipe line in pump house to read the developing pressure including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the SIDCO Officers. Make: H-GURU / ISI MAKE /EQUIVALENT.

Supply, erection, testing and commissioning of suitable Pressure Switch of reputed make line Indfoss or Donfoss including necessary valves, couplings, etc., connected with electrical main control panel and setup at proper differential so as to auto start and auto stop the electrical motor, jockey motor including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., completed as per standard specification and as directed by the Departmental Officers.

Supply, installation, testing and commissioning of following types of extinguisher with provision of wall bracket (fixed with anchor fastener) / Floor mounted as per the specifications. All extinguishers should have the in-built pressure gauge. All extinguishers shall be free from CFC / HCFC. Supply and fixing of advanced model multi purpose ABC stored pressure type fire extinguisher, as per International Standard and specifications (IS:15683), Ready to use condition. ISI Marked, Capacity:6 kgs, complete as per standard specification and as directed by the SIDCO Officers. (Five years warranty)

Supply and fixing of CO2 type fire extinguisher, as per International Standard and specifications (IS:15683), Ready to use condition. ISI Marked, Capacity: 4.5 kgs, complete as per standard specification and as directed by the SIDCO Officers. (Five years warranty)

Supply, Erection, testing and commissioning of Analogue addressable micro Process - controlled Fire Alarm Control Panels with interfacing box, capable of being to the central monitoring System, to monitor and integrated the following quantity of accessories like detectors, MCP's/hooters/control modules, Fault Isolation Modules, hooters, response indicators, fire/fault indicators, audio-visual signals, central processing units, Fire Brigade Phone, complete with LCD display, zone indicating LEDs as per the detailed specification: complete with Battery backup for 48 hours in standby mode and 30 minutes in alarm condition. The system should be capable of detecting fire within 3secs as per UL 9th edition/FM/EN-54 approval with charger for each panel. Each loop should provide with minimum 250 detectors/ devices. Fire panel should be RS-485 communication port and integrate with other Fire panel and Repeater Panel 2 Loop Panel

Supply, Erection, testing and commissioning of Addressable analogue type Multisensory type smoke detectors with dual chamber, solid state design, indicating LED, mounting base, gland and MS base box(Red Colour) etc. as per detailed specification.

Supply, Erection, testing and commissioning of Hooter with relay module and strobe light with minimum 85 db audible and 3m for Audible annunciation and 75cd -110cd flashing at 1 Hz for visual indication.complete and as per technical specification.

Supply, Erection, testing and commissioning of control module for Hooter as per Tender specification

Supply, Erection, testing and commissioning of Hooter Power supply unit with control realy module. It sahll be provided with all suitable mounting accessoreis for as per floor hooter counts.

Supply, Erection, testing and commissioning of Manual call points pull stations with double action type of approved make with NO/NC contacts slim type and projecting out from the surface of enclosure with glass suitable for addressable function(Resettable Type) with inbuilt module

Supply, Erection, testing and commissioning of Fault isolation module to electrically isolate different sections of detector loops with necessary back box

Supply, Erection, testing and commissioning of Networkable fire alarm active repeater panel at security room. It will reflect all parameters of main panel. The rate shall be inclusive of power supply unit

Supply and laying of FRLS PVC insulated 2 core 1.5 sq.mm. Armoured Copper Cable on ceiling / wall using fixing accessories like screws, plug, clamps, etc., as per standard methods and as directed by the Departmental Officers. (RED colour)

Supply and Laying of PVC (Rigid) Pipes (1.8mm thick) with ISI- 25mm concealed in wall / ceiling wit necessary accessories.

Supply and Clambing of PVC (Rigid) Pipes (1.8mm thick) with ISI- 50mm on wall / Shaft / Duct wit necessary accessories.

Supply and Laying of 120/103.50 mm dia HDPE pipe in a trench to be evacuated at a depth of 0.75 mtr and refilling the earth to make good.

SRI RAMANA BUILDING CONSTRUCTIONS PRIVATE LIMITED

POWERCONZ