Supply of furniture and internal fitouts for permanent campus at JNV Kondagaon (Chhattisgarh)

(i) CLASSROOM DESK LARGE SIZE Supply & installation Big Desk (for two persons)-The overall dimensions of desk will be 1066mm * 930mm * Height 760mm, complete as per Specifications enclosed and direction of Engineer-in- charge having the Table top shall be made up of 18.0 mm thick plywood IS 303 of MR Grade OSL (one side shall be laminated, and other side shall have balancer finish). Table top dimensions shall be W 900 mm x D 380 mm. Edge towards bench shall be post formed with round edge. The remaining three edges must be sealed with 2mmthick PVC edge banding tape. Edge band must be trimmed on edges and corners. The desk shall be have low chemical emission of VOCs (Voltage Organic Compounds) and carcinogens, contributing to a healthier room environment. Seat and back rest shall be made of 18mm thick plywood of MR Grade OSL (one side shall be laminated, and other side shall have balancer finish) except back rest. Back rest shall be have both sides colour lamination. Technical details of seat and back rest are mentioned below:Seating bench dimensions shall L 930 mm x W 300 mm. Front side shall be rounded with post forming. Remaining three edges shall sealed with 2mm thick PVC edge banding tape. Back rest dimensions shall L 930 x H 200 mm Upper side shall be rounded with post forming Remaining three edges shall be sealed with 2mm thick PVC edge banding tape. Desk Shelve shall be made of prime quality 0.8mm thick CRCA sheet of H150mmxD300mm and side stiffeners of CRCA tube size 19mmx19mmx1mmthick. One vertical support (partition) of square tube size 25mm square x1.2mm thick must be provided at centre of tray . Upper modesty made of prime quality 0.8mm thick CRCA Sheet Powder Coated should be embossed with dimples in round shape, height will be 150mm, there should be Perforated lower modesty Made of prime quality 0.8 mm thick CRCA sheet of size H150mmXD21mm with square perforation, CRCA Tube of size 19x19x1mm thick to be inserted for full length at bottom of Jali . Bag hook should be provide on both side of piller made of minimum 4mm dia rod Side frame structure:- Made of prime quality CRCA pressed form section 165mmx25mmx1mm thick welded to 25mmx50mmx1.2mm thick CRCA tube , Seat and back side frame structure made of prime quality CRCA pressed form section 165mmx25mmx1mm thick welded to 25.4mm diameter x 1.6mm thick ERW-1pipe , there will be 8no. horizontal supports are 25mmx25mmx1.2mm thick CRCA pipes. . Bottom Rectangular tube 50x25x 1.2mm thick should be closed with PPCP cap bothside sand pipe dia. 25.4x1.6mm thick should be closed with metal (Backside) and other side (Undertheseat) PPCP cap, complete as per engineer incharge Desk should be in semi knock down form with the help 16 connecting pipes ; 8 pipes on each side : connecting pipe size will be 20x20x1.2mm .All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations with CO2 Welding Shall Be Used , CRCA Metal Shall Be Coated After Being Treated With At Least Three Stages And Cleaned From Oil , Grease , Dust And Other Dirt Using Special Thermal Control Coating For Metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² , Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process , Metal Pipe & 7 tank treatment with minimum 45-50 micron powder coating.

(ii) CLASSROOM DESK MEDIUM SIZE Supply & installation Medium Desk (for two persons)-The overall dimensions of desk will be 900mm W± 5 X 890mm D± 5 X 688/420mm H± 5 , complete as per Specifications enclosed and direction of Engineer-in- charge having the Table top shall be made up of 18.0 mm thick plywood IS 303 of MR Grade OSL (one side shall be laminated, and other side shall have balancer finish). Table top dimensions shall be W 870 mm x D 380 mm. Edge towards bench shall be post formed with round edge. The remaining three edges must be sealed with 2mmthick PVC edge banding tape. Edge band must be trimmed on edges and corners.The desk shall be have low chemical emission of VOCs (Voltage Organic Compounds) and carcinogens, contributing to a healthier room environment. Seat and back rest shall be made of 18mm thick plywood of MR Grade OSL (one side shall be laminated, and other side shall have balancer finish) except back rest. Back rest shall be have both sides colour lamination. Technical details of seat and back rest are mentioned below:Seating bench dimensions shall L 890 mm x W 300 mm. Front side shall be rounded with post forming. Remaining three edges shall sealed with 2mm thick PVC edge banding tape. Back rest dimensions shall L 890 x H 200 mm Upper side shall be rounded with post forming Remaining three edges shall be sealed with 2mm thick PVC edge banding tape. Desk Shelve shall be made of prime quality 0.8mm thick CRCA sheet of H150mmxD300mm and side stiffeners of ss CRCA tube size 19mmx19mmx1mmthick. One vertical support (partition) of square tube size 25mm square x1.2mm thick must be provided at centre of tray . Upper moedsty made of prime quality 0.8mm thick CRCA Sheet Powder Coated should be embossed with dimples in round shape, height will be 150mm, there should be Perforated lower modesty Made of prime quality 0.8 mm thick CRCA sheet of size H150mmXD21mm with square perforation, CRCAT ube of size 19x19x1mm thick to be inserted for full length at bottom of Jali . Bag hook should be provide on both side of piller made of minimum 4mm dia rod Side frame structure:- Made of prime quality CRCA pressed form section 165mmx25mmx1mm thick welded to 25mmx50mmx1.2mm thick CRCA tube , Seat and back side frame structure made of prime quality CRCA pressed form section 165mmx25mmx1mm thick welded to 25.4mm diameter x 1.6mm thick ERW-1pipe , there will be 8no. horizontal supports are 25mmx25mmx1.2mm thick CRCA pipes. . Bottom Rectangular tube 50x25x 1.2mm thick should be closed with PPCP cap bothside sand pipe dia. 25.4x1.6mm thick should be closed with metal (Backside) and other side (Undertheseat) PPCP cap, complete as per engineer incharge Desk should be in semi knock down form with the help 16 connecting pipes ; 8 pipes on each side : connecting pipe size will be 20x20x1.2mm .All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations with CO2 Welding Shall Be Used , CRCA Metal Shall Be Coated After Being Treated With At Least Three Stages And Cleaned From Oil , Grease , Dust And Other Dirt Using Special Thermal Control Coating For Metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² , Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process , Metal Pipe & 7 tank treatment with minimum 45-50 micron powder coating.

(iii)TEACHER TABLE :Supplying and installation of knock down type Office Table made of Pre-laminated MDF board with decorative lamination on one side and balancing lamination on other side top of size 1200 X 600 X 750 mm. Worktop shall be rounded in all four corners and should have an overhung of 50mm alongwith one drawer unit made of 0.5mm thick CRCA Steel sheet. The table top shall be supported over legs consists of 4 ss legs with connected beams . pipe sixe 25x25x1.2 mm thick . ss 304 grade.

(iv)Teachers Chair, Overall Dimension:- W600±10 x 600D ±10 x 890H ±10 mm,Seat of Medium back Visitor chair is made of 12mm thick hot pressed plywood pasted with PU Moulded foam with Fabric upholstery on Seat , Used PU Moulded foam on Seat of D-45 kg/m3, Back of Medium back chair is made of Injection moulded PP material structure with Mesh fabric, Seat Size:- 460W ±10 x 470D ±10 x 60Thick. ±5 mm , Back Size:- 440W ±10 x 470H ±10,Armrest:- Fixed PP armrest ,Understructure:- Cantilever frame made SS Polished Finish round pipe with Plastic bushes . Frame Material -SS Polished Finish

(v) TEACHER BOARD [Excluding cost of Interactive Flat-Panel Display (IFPD)] Technical Specification for Smart Board with Double-Track Sliding System for Green and White Boards fitted in an Anodised Aluminium Frame with concealed cable management and provision for mounting of Digital Screen: Supply, installation, testing, commissioning (SITC) of an integrated digital teaching–learning solution comprising: (a) Anodised Aluminium Frame, double track sliding system for white & green board and provision for mounting of digital screen with concealed cable management, (b) Vitrified magnetic ceramic-steel Green Board and White Board panels. • Dimensions and Configuration: Total Width of the Setup is ~12 feet and height ~4.0 feet from the board surface (excluding the width of aluminium frame). • Material: Providing and fixing anodised aluminium (alloy 6063-T6) framed sliding system for smart board with minimum 2.0 mm thick extruded sections, anodised to AA15 grade as p IS 1868, mounted on a heavy-duty top-hung aluminium track (min. 2.5 mm thick) with sealed ball-bearing nylon/PU rollers (load capacity not less than 120 kg per panel), concealed bottom guide, EPDM gaskets, SS-304 fasteners, pelmet/valance cover, and soft end-stops/soft-close mechanism, including all brackets, fixings, alignment, cable provisions, commissioning, and making good complete as per drawings and Engineer-in-Charge. • Design: One slot to fix IFPD, other slot for Green & White boards sliding on double track system with Locking facility on sliding frame to keep the IFPD display safe. • Top & Bottom Rails: Tracks shall be aligned and reinforced to ensure boards move easily and without wobble. • Back Side: The backside of the smart board, to concealed the wall surface, provided & fixed with 18 mm thick HDHMR board laminated (white coloured matte finish) with 0.8 mm, edg sealed with 1 mm PVC edge banding, fixed to the anodised aluminium frame with concealed screws/rivets, with ventilation slots as required, and shall be moisture, termite and borer resistant. •◻Load Capacity: Safe to hold IFPD + white & Green boards with ≥1.5× safety factor. •◻Cable Management: Built-in channels for power, LAN, HDMI, USB. •◻Safety: Rounded edges, tamper-resistant covers, concealed fixing. •◻Finish: Durable, corrosion-resistant coating suitable for indoor use. •◻Additional Requirements: (a) All boards and the structure must be securely fixed to the wall with appropriate fasteners. (b) Provision for cable management must be included for the IFPD (i.e., concealed conduit/path for power and data cables).

(c) The unit must be free from sharp edges, splinters, or any protruding parts that could cause injury. (d) Installation height should ensure comfortable writing access for average adult and student height (typically bottom edge ~2.5 to 3 feet from the floor). (b) Vitrified magnetic ceramic-steel Green Board and White Board panels: • Function: Boards shall slide horizontally on a top and bottom aluminium/steel channel track to fully cover or reveal the IFP as needed. • Material: Vitrified ceramic-steel, magnetic, double-coated. • Sliding Boards: Quantity: 1 no. Green board & 1 no. White board. • Green Board Surface: Matte, chalk-friendly, stain/scratch resistant. • White Board Surface: Glossy surface, Dry-erase marker friendly, ghost-free, easy clean. • Size: ~6 feet (W) × 4 feet (H) (Each Board) with thickness 8mm. • Frame: Anodised aluminium, rounded edges, concealed fasteners.Note - Dimensions mentioned are indicative. Actual may vary as per site requirements

(i) PRINCIPAL ROOM TABLE Table of Size 1800mm (W) x 900mm (D) x 750mm (H) with Side Storage of Size 900mm (W) x 450mm (W) X 750mm (H) and Back Storage 1800mm (W) x 450mm (D) x 750mm (H) as per specifications above

(ii) PRINCIPAL ROOM CHAIR High Back Revolving Chair, Overall Dimension:- 700W ±10 x 700D ±10 x 1210H ±10 mm,Seat of Medium back chair is made of 12mm thick hot pressed plywood pasted with PU Moulded foam with Fabric upholstery on Seat,Used PU Moulded foam on Seat of D-45 kg/m3 , Back of chair is made of Injection moulded PP material structure upholstered with Mesh fabric , Adjustable Lumber support upholstered with fabric , Adjustable Headrest on back Upholstered with Mesh Fabric ,Seat Size:- 470W ±10 x 460D ±10 x 70Thick. ±5 mm , Back Size: 500W ±10 x 780H ±10,Mechanism:- The Synchro tilt Mechanism ,Used gaslift of 90 mm size of Class-IV grade,Armrest:- PU padded adjustable armrest fixed with Seat ,Chair Base & Wheels: SS Polished finish Plated base consists of 5 prongs with 640±5 mm pitch circle diameter, 50mm Dia. Black Nylon - Twin Wheel Pin castor .

(iii) Principal room Visitor Chair, Overall Dimension:- W600±10 x 600D ±10 x 890H ±10 mm,Seat of Medium back Visitor chair is made of 12mm thick hot pressed plywood pasted with PU Moulded foam with Fabric upholstery on Seat , Used PU Moulded foam on Seat of D-45 kg/m3, Back of Medium back chair is made of Injection moulded PP material structure with Mesh fabric, Seat Size:- 460W ±10 x 470D ±10 x 60Thick. ±5 mm , Back Size:- 440W ±10 x 470H ±10,Armrest:- Fixed PP armrest ,Understructure:- Cantilever frame made SS Polished Finish round pipe with Plastic bushes . Frame Material -SS Polished Finish

(iv) VICE-PRINCIPAL ROOM TABLE Table of Size 1650mm (W) x 900mm (D) x 750mm (H) with Side Storage of Size 900mm (W) x 450mm (W) X 750mm (H) and Back Storage 1650 mm (W) x 450mm (D) x 750mm (H) as per specifications above

(v) VICE-PRINCIPAL ROOM CHAIR High Back Revolving Chair, Overall Dimension:- 700W ±10 x 700D ±10 x 1210H ±10 mm,Seat of Medium back chair is made of 12mm thick hot pressed plywood pasted with PU Moulded foam with Fabric upholstery on Seat,Used PU Moulded foam on Seat of D-45 kg/m3 , Back of chair is made of Injection moulded PP material structure upholstered with Mesh fabric , Adjustable Lumber support upholstered with fabric , Adjustable Headrest on back Upholstered with Mesh Fabric ,Seat Size:- 470W ±10 x 460D ±10 x 70Thick. ±5 mm , Back Size: 500W ±10 x 780H ±10,Mechanism:- The Synchro tilt Mechanism ,Used gaslift of 90 mm size of Class-IV grade,Armrest:- PU padded adjustable armrest fixed with Seat ,Chair Base & Wheels: SS Polished Finish base consists of 5 prongs with 640±5 mm pitch circle diameter, 50mm Dia. Black Nylon - Twin Wheel Pin castor .

(vi) Vice Principal Visitor Chair: Overall Dimension:- W600±10 x 600D ±10 x 890H ±10 mm,Seat of Medium back Visitor chair is made of 12mm thick hot pressed plywood pasted with PU Moulded foam with Fabric upholstery on Seat , Used PU Moulded foam on Seat of D-45 kg/m3, Back of Medium back chair is made of Injection moulded PP material structure with Mesh fabric, Seat Size:- 460W ±10 x 470D ±10 x 60Thick. ±5 mm , Back Size:- 440W ±10 x 470H ±10,Armrest:- Fixed PP armrest ,Understructure:- Cantilever frame made SS Polished Finish round pipe with Plastic bushes . Frame Material -SS Polished Finish

(i)SOFA FOYER ONE SEATER Size in mm - 880(L) X 755(D) X 750(H) Seat Wooden Structure Uphostered With Leatherite & HD Foam 32 Softy. SS Chrome . Sofa S57 Max. Height 750mm . The rounded Armrests Provided Sleek And Stylish Look With The Pillowed Back . Arm Rest Leatherite Covered With Solid Wood Structure . Understructure Made By Solid Wood Structures With Heavy Quality Spring For Maximum Comfort , Taper Type 25mm Round Spiral Spring . Legs Round Pipe Chrome Plated Legs . Understructure Made of Base Frame Strongly Jointed Wooden Plywood Parts . 3 Seater Sofa Seat Height From Ground 460mm .3 Seater Sofa 2020W x 760D x 750H , 2 Seater Sofa 1450W x 760D x 750H . Seat Height From Ground 460mm & 1 Seater Sofa 880W x 760D x 750H . 100mm High Legs . Note - Dimensions mentioned are indicative. Actual may vary as per site requirements

(ii)SOFA FOYER TWO SEATER Size in mm - 1460(L) X 755(D) X 750(H) Seat Wooden Structure Uphostered With Leatherite & HD Foam 32 Softy. SS Chrome . Sofa S57 Max. Height 750mm . The rounded Armrests Provided Sleek And Stylish Look With The Pillowed Back . Arm Rest Leatherite Covered With Solid Wood Structure . Understructure Made By Solid Wood Structures With Heavy Quality Spring For Maximum Comfort , Taper Type 25mm Round Spiral Spring . Legs Round Pipe Chrome Plated Legs . Understructure Made of Base Frame Strongly Jointed Wooden Plywood Parts . 3 Seater Sofa Seat Height From Ground 460mm .3 Seater Sofa 2020W x 760D x 750H , 2 Seater Sofa 1450W x 760D x 750H . Seat Height From Ground 460mm & 1 Seater Sofa 880W x 760D x 750H . 100mm High Legs . Note - Dimensions mentioned are indicative. Actual may vary as per site requirements

(iii)SOFA FOYER THREE SEATER Size in mm - 1930(L) X 755(D) X 750(H) Seat Wooden Structure Uphostered With Leatherite & HD Foam 32 Softy. SS Chrome . Sofa S57 Max. Height 750mm . The rounded Armrests Provided Sleek And Stylish Look With The Pillowed Back . Arm Rest Leatherite Covered With Solid Wood Structure . Understructure Made By Solid Wood Structures With Heavy Quality Spring For Maximum Comfort , Taper Type 25mm Round Spiral Spring . Legs Round Pipe Chrome Plated Legs . Understructure Made of Base Frame Strongly Jointed Wooden Plywood Parts . 3 Seater Sofa Seat Height From Ground 460mm .3 Seater Sofa 2020W x 760D x 750H , 2 Seater Sofa 1450W x 760D x 750H . Seat Height From Ground 460mm & 1 Seater Sofa 880W x 760D x 750H . 100mm High Legs . Note - Dimensions mentioned are indicative. Actual may vary as per site requirements

(iv) Coffee Table The coffee table measures 900 mm (W) × 600 mm (D) × 450 mm (H) and features a 10 mm thick clear tempered glass top and shelf supported on a Stainless Steel 304 frame made of 40×40 mm square tubes with a mirror-polished finish. All joints are argon-welded, ground, and buffed for a seamless look. The lower glass shelf for additional storage, and rubber pads or level adjusters are provided at the base for stability and floor protection. The table combines modern design, durability, and elegant finish, making it ideal for offices and reception areas.

(i) TABLE (SEATING CAPACITY AS PER ACTUAL REQUIREMENT) Supplying and installation of a modular, knock-down center island table sized approximately 3600 mm in length (adjustable to actual requirements) by 1350 mm in width and 750 mm in height, constructed from high-quality 18 mm thick commercial grade plywood or BWR (Boiling Water Resistant) grade plywood with decorative lamination on visible faces and balanced lamination beneath for enhanced strength and moisture resistance. All edges are sealed with 2 mm thick machine-pressed PVC edge banding bonded with industrial adhesive to ensure a seamless, monolithic appearance. The gable ends are fabricated of the same 18 mm thick commercial grade plywood with decorative lamination on both sides and matching edge banding for consistent aesthetics and superior durability. The table shall have an underbody vertical support panel running continuously along its length to enhance stability and strength. The understructure uses precision-cut, laminated plywood panels assembled with knock-down fittings for ease of installation and future reconfiguration, ensuring superior load-bearing capacity and long-term durability. A concealed wire management system beneath the worktop integrates pre-laminated plywood cable trays or high-quality plastic trays fixed with durable brackets, complete with provisions for switch plates and grommets to facilitate safe, organized routing of electrical and data cables. All surfaces are finished for scratch and stain resistance with anti- fungal and moisture-resistant properties, and installation will follow best woodworking practices, with final dimensions and seating capacity determined by the actual site layout Note - Dimensions mentioned are indicative. Actual may vary as per site requirements

(ii) WORK SPACE WITH IN-BUILT LOCKABLE OVERHEAD STORAGE SPACE FOR STAFFROOM (AS PER ACTUAL REQUIREMENT) Supplying and installation of site knock-down type modular wall-mounted workspace unit of approximate size 900W x 600D x 750H mm (for one staff), including working counter and lockable overhead storage cabinet of 900W x 450D x 650H mm. The structure shall be made of 18 mm thick BWP grade plywood with decorative laminate on external surfaces and balancing laminate on inner faces conforming to IS:303/IS:12406. All exposed edges shall be sealed with 2 mm PVC edge banding. The worktop shall be 25 mm thick pre-laminated MDF board with post-formed front edge and machine-pressed PVC edge banding, securely fixed to the wall using concealed MS cleats and brackets. The overhead cabinet shall be fitted with soft-close concealed hinges, SS handles, and magnetic catchers of approved make, with one adjustable shelf and modular connectors for alignment and expansion to adjoining units. Each workspace shall include provision for electrical connectivity with 6A/16A modular sockets (as per requirement) positioned at approximately 450 mm above finished floor level for easy access. The worktop shall have a circular cable hole (50–60 mm diameter) with grommet for laptop and equipment wiring. All wiring, sockets, and conduits shall be concealed neatly within the table body, routed through internal PVC raceways to maintain a clean, clutter-free appearance. Junction boxes and ducts shall be integrated to provide safe, organized cable management without visible wiring. The entire unit shall be wall-mounted using heavy-duty MS brackets or suitable fasteners based on wall type, finished neatly with matching silicone sealant at all joints. All fittings and hardware, including soft-close hinges and handles, shall be of reputed make. The unit shall be termite-resistant, moisture-resistant, easy to maintain, and made from ISI-marked prime quality boards. The overall layout and detailing shall match the approved reference image, with actual dimensions finalized as per site requirements and direction of the Engineer-in-Charge. Note - Dimensions mentioned are indicative. Actual may vary as per site requirements

(iii) Chair Overall Dimension:- W600±10 x 600D ±10 x 890H ±10 mm,Seat of Medium back Visitor chair is made of 12mm thick hot pressed plywood pasted with PU Moulded foam with Fabric upholstery on Seat , Used PU Moulded foam on Seat of D-45 kg/m3, Back of Medium back chair is made of Injection moulded PP material structure with Mesh fabric, Seat Size:- 460W ±10 x 470D ±10 x 60Thick. ±5 mm , Back Size:- 440W ±10 x 470H ±10,Armrest:- Fixed PP armrest ,Understructure:- Cantilever frame made SS Polished Finish round pipe with Plastic bushes . Frame Material -SS Polished Finish

(iv) PERSONAL LOCKER UNIT FOR STAFFROOM AND ONE EACH FOR PRINCIPAL AND VICE PRINCIPAL ROOM Supplying and installation of Metal Lockers with Cam Lock one unit consiting of 380mm (W) x 450mm (D) x 1800 mm (H) with 4 Lockers. Body-LH and RH Side and back panel is made up of 0.8mm thick CRCA steel sheet confirming to IS 513:2008. Shelf hanging bracket is welded on both the side panel by spot welding. Shelf hanging bracket is made up of 0.8mm thick CRCA steel sheet confirming to IS 513:2008. front frame, top and bottom part made up 0.8mm thick CRCA steel sheet confirming to IS 513:2008 and horizontal part is made up 0.8 mm thick CRCA Steel sheet confirming to IS 513:2008. On a front frame horizontally provision is given at a common distance to hold shutter bracket. Locker’s top is made up of 0.8mm thick CRCA Steel sheet confirming IS 513:2008 which is having standard dimension 375 x378mm. Shelf is also made up of 0.8 mm CRCA Steel sheet confirming to IS 513:2008. Shutter- Is made up on 0.8mm thick CRCA Steel sheet confirming to IS 513:2008. All the shutter are hung on shutter pin and shutter bracket, louvers are given in shutter for air flow. PVC flush handle and name plate is used for handling and for name plate tagging. Standard locking arrangment is used for locking each shutter. The bodies including shelves are given anti-rust surface treatment & are powder coated with epoxy polyester powder coating of DFT 50- 60 Micron confirimg to IS 13871:1993.

(i) Supply and installation of Glass-door Storage of Size 915 mm (W) x 482mm (D) x 1980mm (H). It should have shelf thickness of 0.8mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) with clear glass of > 4.0 mm thick and all other components shall have a thickness of 0.8mm. These components shall be made of CRCA steel sheet ‘D’ grade high yield strength as per IS 513:2008 The glass door storwel shall have a SS handle and a Two-way locking mechanism with shooting bolt. It should have a height-wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base.All metal components would be epoxy polyster powder coated DFT 50-60 Micron confirimg to IS 13871:1993 Note - Dimensions mentioned are indicative. Actual may vary as per site requirements

(ii) Wall mounted built in open book shelf : Overall Size 900L (length may vary as per actual requirement) X300DX2100Hmm,Top made up of 18mm thick Postlam plywood with PVC edge banding ,Side panel made up of 18mm thick Postlam plywood with PVC edge bending , Skirting made up of 18mm thick Postlam plywood with PVC edge bending ,back panel made up of 18mm thick Postlam plywood , One number of drawer and Bottom Storage Cabinets as per ref. image ,shelf made up of 18mm thick Postlam plywood with PVC edge bending, all Wooden Panels Fix Joints With Minifix Dowels & other Fitting Equipment , All Wooden Panels Prime Quality Board With ISI Marked. Complete structure design should be as per reference image only. Note - Dimensions mentioned are indicative. Actual may vary as per site requirements

(iii) TABLE as per ref image:Supply and installation of Library Table in sizes of 3600mm (L) (length may vary as per actual requirement) x 900mm (W) x 750mm (H) consisting of follwing specification:- Work Top - Work top shall be made of 25mm thick Pre-laminated Partical Board with decorative lamination on one side and balancing lamination on other side confirming to IS 12823: 1990, alongwith 2 mm thick Machine pressed PVC edge banding glued with industrial adhesive and monolithically diffused with board on exposed edges. Understructure Supporting frame shall consists of 03 Metal C-Legs (two at either ends and one in middle of table) and joined by two numbers Horizontal connector made of tubular section 40mm x 40mm x 1.6mm (wall thickness) confirming to IS 4923:1997. The entire metal frame shall be finised with epoxy polyster powder coated DFT 50-60 Micron. C-typed metal legs shall be kept 150 mm inside from from end of table. Legs shall be fitted to the ground with M8 screw leveler with the height adjustment up to 12mm to 15mm. Note - Dimensions mentioned are indicative. Actual may vary as per site requirements

(iv) Chair, Overall Dimension:- W600±10 x 600D ±10 x 890H ±10 mm,Seat of Medium back Visitor chair is made of 12mm thick hot pressed plywood pasted with PU Moulded foam with Fabric upholstery on Seat , Used PU Moulded foam on Seat of D-45 kg/m3, Back of Medium back chair is made of Injection moulded PP material structure with Mesh fabric, Seat Size:- 460W ±10 x 470D ±10 x 60Thick. ±5 mm , Back Size:- 440W ±10 x 470H ±10,Armrest:- Fixed PP armrest ,Understructure:- Cantilever frame made SS Polished Finish round pipe with Plastic bushes . Frame Material -SS Polished Finish

(i) COMPUTER WORK STATION Supplying and installation of knock down type Dual Computer Work Station of unit Size 1500mm (L) x 600m (W) x 750mm (H) for two students Work Top- Work top shall be made 25mm thick Prelam particle board with decorative lamination on one side and balancing lamination on other side confirming to IS 12823: 1990 with 2mm thick Machine pressed PVC edge banding glued with industrial adhesive and monolithically diffused with board on all sides. Understructure supporting frame consist of PLBP Gable ends of 18mm Wire management-The Vertical /Electrical duct & Horizontal Cable tray ( wire carriers) are made of CRCA steel sheet & fixed to the understructure below worktop with specially designed brackets. Provision for fixing Switch plates are privided in the cable tray for easy access through wire mangaer or PVC grommet.

(ii) COMPUTER CHAIR FOR STUDENT Medium Back Revolving Chair, Overall Dimension:- 700W ±10 x 700D ±10 x 1010H ±10 mm,Seat of Medium back chair is made of 12mm thick hot pressed plywood pasted with PU Moulded foam with Fabric upholstery on Seat ,Used PU Moulded foam on Seat of D-45 kg/m3 , Back of chair is made of Injection moulded PP material structure combination of upholstered with Mesh fabric , Seat and back connected through metal powder coated plate having Adjustable Lumber support upholstered with fabric , Seat Size:- 490W ±10 x 450D ±10 x 70Thick. ±5 mm , Back Size: 525W ±10 x640H ±10,Mechanism:- The Synchro tilt Mechanism ,Using gaslift of 90 mm size of Class 3 grade,Armrest: PU Padded Adjustable armrest,Chair Base & Wheels: Revolving Pedestal SS Polsihed Finish base consists of 5 prongs with 640±5 mm pitch circle diameter, 50mm Dia. Black Nylon - Twin Wheel Pin castor .

(i) Supply and installation of Glass-door Storage of Size 915 mm (W) x 482mm (D) x 1980mm (H). It should have shelf thickness of 0.8mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) with clear glass of > 4.0 mm thick and all other components shall have a thickness of 0.8mm. These components shall be made of CRCA steel sheet ‘D’ grade high yield strength as per IS 513:2008 The glass door storwel shall have a SS handle and a Two-way locking mechanism with shooting bolt. It should have a height-wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base.All metal components would be epoxy polyster powder coated DFT 50-60 Micron confirimg to IS 13871:1993 Note - Dimensions mentioned are indicative. Actual may vary as per site requirements

ALONG THE WALL TABLE:: Supply and installation of Along-the-wall knock down type modular laboratory tables of size 1400 MM(L) (Length may vary as per actual requirement) × 750 MM (W) × 860MM(H) mm × 900MM H . Each unit shall have a storage box of size 1400W × 750D × 850H. The worktops will include a powder-coated bus running their full length, above the counter, with an internal conduit for all wiring. Modular switch plates and 02 nos of 220V/16A Switch socket (with individual circuit protection) will be CNC-mounted every 1 m (or per site layout). All conduits and components shall comply with applicable laboratory safety and performance standards. Dust-proof, removable access covers to permit maintenance and future upgrades, and outlets to be ergonomically positioned for seated and standing use. Additional switches and sockets shall be provided as required. All base storage cabinets shall be of the design “1 Drawer + 2 Shutters” made of 0.8 mm thick Powder Coated CRCA. Each storage box without granite shall be 600W × 570D × 713H, supported on 100 mm legs and shall include rubber shoes at the bottom of each leg to prevent floor damage and ensure stability. The upper top shall be of 19 mm thick black granite, with all joints sealed using silicon sealant. The cabinet bodies shall be of over-closing design, fabricated entirely on CNC machines to ensure precision. The storage bodies shall be neatly jointed with accurately matched sides to avoid gaps. Shutters shall be made of 0.8 mm thick powder coated CRCA with handles, and drawers shall run on innotech technology sliding channels. The worktops shall be of 19 mm thick black granite, flushed with sink units and taps. Installation shall include all utility service outlets, accessory fittings, plumbing, electrical switches, and fittings shall be as per requirement. All metallic parts shall be with corrosion resistant coating and shall be welded strongly using CO₂ welding, conforming to safety regulations. Panels shall be secured with nuts, bolts, and riveting. Note: All dimensions mentioned are indicative and may vary as per actual site requirements

ISLAND TABLE:The laboratory table shall be provided as knock down type modular ISLAND laboratory tables units of overall size 8000(L) (Length may vary as per actual requirement) × 1500(W) × 860(H) mm × 900H . It shall be constructed in modular segments of 1400(L) × 1500(W) × 860(H) mm each for ease of manufacture, handling, and installation. Storage boxes shall be of size 1400W × 1500D × 850H. The worktops will include a powder-coated bus running their full length, above the counter, with an internal conduit for all wiring. Modular switch plates and 04 nos (02 Facing each side) of 220V/16A Switch socket (with individual circuit protection) will be CNC-mounted every 1 m (or per site layout). All conduits and components shall comply with applicable laboratory safety and performance standards. Dust-proof, removable access covers to permit maintenance and future upgrades, and outlets to be ergonomically positioned for seated and standing use. Additional switches and sockets shall be provided as required. All base storage cabinets shall be of the design “1 Drawer + 2 Shutters” made of 0.8 mm thick Powder Coated CRCA. Each storage box without granite shall be 600W × 570D × 713H, supported on 100 mm legs and shall include rubber shoes at the bottom of each leg to prevent floor damage and ensure stability. The upper top shall be of 19 mm thick black granite, with all joints sealed using silicon sealant. The cabinet bodies shall be of over-closing design, fabricated entirely on CNC machines to ensure precision. The storage bodies shall be neatly jointed with accurately matched sides to avoid gaps. Shutters shall be made of 0.8 mm thick Powder Coated CRCA with handles, and drawers shall run on innotech technology sliding channels. The worktops shall be of 19 mm thick black granite, flushed with sink units and taps. Installation shall include all utility service outlets, accessory fittings, plumbing, electrical switches, and fittings shall be as per requirement. All metallic parts shall be with corrosion resistant coating and shall be welded strongly using CO₂ welding, conforming to safety regulations. Panels shall be secured with nuts, bolts, and riveting. Note: All dimensions mentioned are indicative and may vary as per actual site requirements

ALONG THE WALL TABLE: Supply and installation of Along-the-wall knock down type modular laboratory tables of size 1400(L) (Length may vary as per actual requirement) × 750(W) × 860(H) mm × 1550H (two-tier). Each unit shall have a storage box of size 1400W × 750D × 850H. Four standard ceramic sinks shall be installed, each fitted with a 3-way faucet of Premier make. Reagent racks made completely out of stainless steel shall be provided to cover the entire table length(along the wall) except the sink area. These racks shall be 300D × 700H and of complete modular design, consisting of two horizontal storage shelves made of stainless steel with suitable cutouts for electrical switches and sockets. Additional switches and sockets shall be provided as required. All base storage cabinets shall be of the design “1 Drawer + 2 Shutters” made of 0.8 mm thick stainless steel sheet polished finish. Each storage box without granite shall be 600W × 570D × 713H, supported on 100 mm SS legs and shall include rubber shoes at the bottom of each leg to prevent floor damage and ensure stability. The upper top shall be of 19 mm thick black granite, with all joints sealed using silicon sealant. The cabinet bodies shall be of over-closing design, fabricated entirely on CNC machines to ensure precision. The storage bodies shall be neatly jointed with accurately matched sides to avoid gaps. Shutters shall be made of 0.8 mm thick powder coated stainless steel sheet with handles, and drawers shall run on innotech technology sliding channels. Reagent shelves shall be made of a SS, provided with electrical switches, sockets, and cutouts as required. The worktops shall be of 19 mm thick black granite, flushed with sink units and taps. Installation shall include all utility service outlets, accessory fittings, plumbing, electrical switches, and fittings shall be as per requirement. All metallic parts shall be with corrosion resistant coating and shall be welded strongly using CO₂ welding, conforming to safety regulations. Panels shall be secured with nuts, bolts, and riveting. Note: All dimensions mentioned are indicative and may vary as per actual site requirements

ISLAND TABLE: The laboratory table shall be provided as knock down type modular ISLAND laboratory tables units of overall size 8000(L) (Length may vary as per actual requirement) × 1500(W) × 860(H) mm × 1550H (two-tier). It shall be constructed in modular segments of 1600(L) × 1500(W) × 860(H) mm each for ease of manufacture, handling, and installation. Storage boxes shall be of size 1400W × 1500D × 850H. Four standard ceramic sinks of size shall be installed, each fitted with a 3-way faucet of Premier make. Stainless steel reagent racks shall be provided across the entire table length in centre except the sink areas, with dimensions 300D × 700H. These racks shall also be of modular design with two horizontal stainless steel shelves, cutouts for switches and sockets, provision for electrical outlets, and accommodation for granite pieces. All base storage cabinets shall be of the design “1 Drawer + 2 Shutters” made of 0.8 mm thick Powder Coated CRCA. Each storage box without granite shall be 600W × 570D × 713H, supported on 100 mm SS legs and shall include rubber shoes at the bottom of each leg to prevent floor damage and ensure stability. The upper top shall be of 19 mm thick black granite, with all joints sealed using silicon sealant. The cabinet bodies shall be of over-closing design, fabricated entirely on CNC machines to ensure precision. The storage bodies shall be neatly jointed with accurately matched sides to avoid gaps. Shutters shall be made of 0.8 mm thick powder coated Powder Coated CRCA with handles, and drawers shall run on innotech technology sliding channels. Reagent shelves shall be made of a polished finish SS, provided with electrical switches, sockets, and cutouts as required. The worktops shall be of 19 mm thick black granite, flushed with sink units and taps. Installation shall include all utility service outlets, accessory fittings, plumbing, electrical switches, and fittings shall be as per requirement. All metallic parts shall be with corrosion resistant coating and shall be welded strongly using CO₂ welding, conforming to safety regulations. Panels shall be secured with nuts, bolts, and riveting. Note: All dimensions mentioned are indicative and may vary as per actual site requirements

ALONG THE WALL TABLE: Supply and installation of Along-the-wall knock down type modular laboratory tables of size 1400(L) (Length may vary as per actual requirement) × 750(W) × 860(H) mm × 1550H (two-tier). Each unit shall have a storage box of size 1400W × 750D × 850H. Four standard ceramic sinks shall be installed, each fitted with a 3-way faucet of Premier make. Reagent racks made completely out of stainless steel shall be provided to cover the entire table length(along the wall) except the sink area. These racks shall be 300D × 700H and of complete modular design, consisting of two horizontal storage shelves made of stainless steel with suitable cutouts for electrical switches and sockets. Additional switches and sockets shall be provided as required. All base storage cabinets shall be of the design “1 Drawer + 2 Shutters” made of 0.8 mm thick stainless steel sheet polished finish. Each storage box without granite shall be 600W × 570D × 713H, supported on 100 mm SS legs and shall include rubber shoes at the bottom of each leg to prevent floor damage and ensure stability. The upper top shall be of 19 mm thick black granite, with all joints sealed using silicon sealant. The cabinet bodies shall be of over-closing design, fabricated entirely on CNC machines to ensure precision. The storage bodies shall be neatly jointed with accurately matched sides to avoid gaps. Shutters shall be made of 0.8 mm thick powder coated stainless steel sheet with handles, and drawers shall run on innotech technology sliding channels. Reagent shelves shall be made of a SS, provided with electrical switches, sockets, and cutouts as required. The worktops shall be of 19 mm thick black granite, flushed with sink units and taps. Installation shall include all utility service outlets, accessory fittings, plumbing, electrical switches, and fittings shall be as per requirement. All metallic parts shall be with corrosion resistant coating and shall be welded strongly using CO₂ welding, conforming to safety regulations. Panels shall be secured with nuts, bolts, and riveting. Note: All dimensions mentioned are indicative and may vary as per actual site requirements

ISLAND TABLE: The laboratory table shall be provided as knock down type modular ISLAND laboratory tables units of overall size 8000(L) (Length may vary as per actual requirement) × 1500(W) × 860(H) mm × 1550H (two-tier). It shall be constructed in modular segments of 1400(L) × 1500(W) × 860(H) mm each for ease of manufacture, handling, and installation. Storage boxes shall be of size 1400W × 1500D × 850H. Four standard ceramic sinks of size shall be installed, each fitted with a 3-way faucet of Premier make. Stainless steel reagent racks shall be provided across the entire table length in centre except the sink areas, with dimensions 300D × 700H. These racks shall also be of modular design with two horizontal stainless steel shelves, cutouts for switches and sockets, provision for electrical outlets, and accommodation for granite pieces. All base storage cabinets shall be of the design “1 Drawer + 2 Shutters” made of 0.8 mm thick Powder Coated CRCA. Each storage box without granite shall be 600W × 570D × 713H, supported on 100 mm legs and shall include rubber shoes at the bottom of each leg to prevent floor damage and ensure stability. The upper top shall be of 19 mm thick black granite, with all joints sealed using silicon sealant. The cabinet bodies shall be of over-closing design, fabricated entirely on CNC machines to ensure precision. The storage bodies shall be neatly jointed with accurately matched sides to avoid gaps. Shutters shall be made of 0.8 mm thick Powder Coated CRCA with handles, and drawers shall run on innotech technology sliding channels. Reagent shelves shall be made of polished finish SS, provided with electrical switches, sockets, and cutouts as required. The worktops shall be of 19 mm thick black granite, flushed with sink units and taps. Installation shall include all utility service outlets, accessory fittings, plumbing, electrical switches, and fittings shall be as per requirement. All metallic parts shall be with corrosion resistant coating and shall be welded strongly using CO₂ welding, conforming to safety regulations. Panels shall be secured with nuts, bolts, and riveting. Note: All dimensions mentioned are indicative and may vary as per actual site requirements

(iv) LAB STOOL Supply and installation of Lab Stool Seat Revolving Stool with Backrest Overall Dimension: 410W ±10 x 410D ±10 x 820H ±10 mm,Seat of chair is made of 12mm thick hot pressed Plywood pasted with High Density PU foam & Leatherette upholstery, Back is made of 12mm thick hot pressed Plywood pasted with PU foam D -40 kg/m3 , H-20 Seat and back fixed through metal powder coated Spine covered with plastic cover, Seat Size: 400W ±10 x 400D ±10 x 75Thick. ±5 mm, Back Size: 450W ±10 x 240H ±10 x 50Thick. ±5mm, Ground to seat height-440-560mm, Mechanism:- Machanism Design With Features Of Revolving At 360 Degree. Machanism Provided Upright Position Locking, Seating Height Can Be Adjusted With a Pneumatic Gas Lift,Gaslift: Lift -Used gaslift of 90 mm size of Class- IV grade with plastic bellow cover, Chair Base & Wheels: Chair Base Made of polished finished SS 304 grade stainless steel, base consists of polished finished SS 304 grade stainless steel 5 prongs with 560±5 mm pitch circle diameter, Polished finished SS 304 grade stainless steel circular foot rest as per ref. image, 50mm Dia. Black Nylon - Twin Wheel Pin castor.

(A) DINING TABLE Dining Table: Polished finish SS Dinning Table consists of Dinning Top is made up of 1 mm thickness Stainless steel sheet of SS 304 Grade with overall dimension of 1800(L) X 700(D) X 750(H). The table top is reinforced with a 18 mm ply Board on Stainless steel frame of square section 40mmx40mmx1.6mm. Dinning top of stainless steel sheet shall be extended to the sides and a depth upto 40 mm under the table top in all directions including edge rounding, grinding and finishing etc. all complete. The Table top shall finish in such a manner to avoid any sharp edges. The table will be supported by four hollow legs made from SS 304 grade stainless steel. The hollow legs shall be of square type of size 50mmx50mmx1.6mm. These legs shall be securely welded or mechanically fastened to the underside of the tabletop frame. For additional structural stability, stainless steel cross supports shall be provided between the legs as shown in figure with 40mmx40mmx1.6mm SS square section. The table shall include rubber shoes at the bottom of each leg to prevent floor damage and ensure stability. The design shall prioritize user safety with no sharp corners or edges. The table must be structurally sound and capable of supporting a uniformly distributed load of at least 250 kg. All materials used must conform to relevant IS standards, and the finished product should be free from burrs, dents, or deformities. Note - Dimensions mentioned are indicative. Actual may vary as per site requirements

(B) DINING BENCH Dining Bench: The Bench shall be of size 1800 mm in length, 300 mm in depth, and 450 mm in height, suitable for use in residential schools. The bench top shall be made of 18 mm thick HDHMR + Laminated , finished with a 1 mm thick decorative laminate on the top surface, and a balancing laminate backing on the underside to ensure dimensional stability. All exposed edges shall be sealed with PVC edge banding or machine-finished to prevent splinters and enhance durability. The plywood shall be scratch-resistant, water-resistant, and easy to clean, with a light woodgrain or equivalent finish as approved. The supporting frame shall be fabricated frame of square hollow section 40mmx40mmx1.6mm SS 304 grade stainless steel in polished finish. These legs shall be securely welded to the underside of the benchtop frame. The bench shall include rubber shoes at the bottom of each leg to prevent floor damage and ensure stability. The design shall prioritize user safety with no sharp corners or edges. The bench must be structurally sound and capable of supporting a uniformly distributed load of at least 250 kg. All materials used must conform to relevant IS standards, and the finished product should be free from burrs, dents, or deformities.

Plyboard ON BEDs/Tables/ Partition wall In Dormitory Hall, RCC Bed (900mmX1800mm) with 8mm HDHMR with 2mm Matt-finish laminate on top of bed shall be provided. RCC study counter (600mmX1200mm) with granite on top. RCC partition wall cladding must be using 8mm Plywood covered with 2mm Matt-finish laminate all around corners and no sharp edges. With all fixtures fasteners adhesives etc all inclusive required for fixing.

i) King Size BED: The king-size bed is constructed without a storage box and features robust materials for lasting durability. The frame, including the side panels and footboard, is made from 18 mm thick pre-laminated engineered wood with a melamine finish, offering a clean, wood-textured look. The mattress base is fabricated using 18 mm BWP-grade plywood, fully edge-banded to prevent warping and moisture damage. The overall dimensions of the bed are 2040 mm in length, 1980 mm in width, and 300 mm in height to the base, providing ample support for a standard king-size mattress (1980 mm × 1830 mm). The headboard stands 800 mm tall and is divided into two sections. The lower portion is made of laminated board, while the upper section includes a cushioned panel with 50 mm PU foam, upholstered in stitched premium leatherette for added comfort and aesthetics. The entire unit features a light oak melamine finish to match. The bed is supplied in knock-down condition with all necessary hardware, including cam locks, screws, dowels, and angle brackets. Assembly is straightforward with reinforced metal corners for added strength.

ii) Side Table:The side table is constructed using high-grade plywood and finished in a light oak melamine laminate for a clean, natural appearance. It features a compact form with overall dimensions of 400 mm (width) × 400 mm (depth) × 490 mm (height). The unit has two lockable equally sized drawers, both equipped with soft-close telescopic channels for smooth, quiet operation. The design incorporates a handle-less front with a finger-pull recess at the top edge of each drawer for a sleek and minimalist look. Both drawers are lockable, enhancing functionality and security for personal storage. The surface is fully laminated for protection against wear and easy maintenance.

iii) 06 Seater Dining Table— The dining table shall be of solid sheesham wood (kiln-dried and chemically treated) with overall dimensions 1500 mm × 900 mm × 760 mm and a tabletop thickness of approx. 25 mm; the apron shall be 25 mm thick and legs shall be 80–100 mm square in section, all joined using mortise-and-tenon or equivalent reinforced joinery. A clear tempered (toughened) glass top shall be provided to cover the wooden top: 10 mm clear toughened glass is recommended for this size, with machine-polished edges (flat polish or small bevel) and corner radii for safety. The glass shall be supplied cut to size for a nominal 2–3 mm reveal from the top edge of the apron (or as directed), packed separately and fitted on site. Glass fixing shall use non-marking neoprene/rubber support pads (minimum 6 pads per table) and anti-slip silicone adhesive/dots to hold the glass in place without damaging the wood; stainless steel decorative clamps may be provided where a visible fixing is required but should not bear the primary load. Finish of the wood shall be a low-sheen natural polish or clear lacquer; table shall be supplied knock-down with all required fasteners and instructions for on-site assembly and final glass placement. The glass top protects the wood from scratches, heat and spills, gives a sleek aesthetic, and makes cleaning easier (wipe with standard glass cleaner while avoiding aggressive solvents on adjacent wood finish). Chairs 06 Nos — Each chair shall be of solid sheesham wood, finished to match the table’s low-sheen polish, with a slatted backrest and straight legs. Seat height shall be 450 mm from finished floor level. Seats shall be cushioned with medium-density foam and fully upholstered in durable synthetic leather (leatherette) in a neutral tone; foam shall be supported on a plywood board beneath the cushion. Chair dimensions (seat width/depth/backrest height) and leg sections shall be robust to match the table and shall be supplied knock-down with necessary assembly hardware. Upholstery shall be stain-resistant and maintainable (spot cleanable); wood and upholstery care instructions shall be provided with each unit.

(a)SOFA FOYER ONE SEATER Size in mm - 880(L) X 755(D) X 750(H) Seat Wooden Structure Uphostered With Leatherite & HD Foam 32 Softy. SS Chrome . Sofa S57 Max. Height 750mm . The rounded Armrests Provided Sleek And Stylish Look With The Pillowed Back . Arm Rest Leatherite Covered With Solid Wood Structure . Understructure Made By Solid Wood Structures With Heavy Quality Spring For Maximum Comfort , Taper Type 25mm Round Spiral Spring . Legs Round Pipe Chrome Plated Legs . Understructure Made of Base Frame Strongly Jointed Wooden Plywood Parts . 3 Seater Sofa Seat Height From Ground 460mm .3 Seater Sofa 2020W x 760D x 750H , 2 Seater Sofa 1450W x 760D x 750H . Seat Height From Ground 460mm & 1 Seater Sofa 880W x 760D x 750H . 100mm High Legs.

(b)SOFA FOYER TWO SEATER Size in mm - 1460(L) X 755(D) X 750(H) Seat Wooden Structure Uphostered With Leatherite & HD Foam 32 Softy. SS Chrome . Sofa S57 Max. Height 750mm . The rounded Armrests Provided Sleek And Stylish Look With The Pillowed Back . Arm Rest Leatherite Covered With Solid Wood Structure . Understructure Made By Solid Wood Structures With Heavy Quality Spring For Maximum Comfort , Taper Type 25mm Round Spiral Spring . Legs Round Pipe Chrome Plated Legs . Understructure Made of Base Frame Strongly Jointed Wooden Plywood Parts . 3 Seater Sofa Seat Height From Ground 460mm .3 Seater Sofa 2020W x 760D x 750H , 2 Seater Sofa 1450W x 760D x 750H . Seat Height From Ground 460mm & 1 Seater Sofa 880W x 760D x 750H . 100mm High Legs.

(c) Coffee Table The coffee table measures 900 mm (W) × 600 mm (D) × 450 mm (H) and features a 10 mm thick clear tempered glass top and shelf supported on a Stainless Steel 202 frame made of 40×40 mm square tubes with a mirror-polished finish. All joints are argon-welded, ground, and buffed for a seamless look. The lower glass shelf for additional storage, and rubber pads or level adjusters are provided at the base for stability and floor protection. The table combines modern design, durability, and elegant finish, making it ideal for offices and reception areas.

Please Enable Macros to View BoQ information