PROVN OF TRAINING SHED FOR ARMT WING (12 X 18 MTR) AT TRAINING AREA NEAR BLDG NO P-277, PROVN OF FOUR GREASE TRAP FOR 04 X COOK HOUSE AT SOTT AND 02 X MINOR WORKS UNDER GE (N) AHMEDNAGAR

Amount

Excavating post holes or similar holes, each not exceeding 0.5 Cum, getting out in any type of soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance n.exc 50m & making good surface

Excavation over areas not exceeding 1.5 M deep and getting out in soft/loose soil.

M&L for Moorum filling in floors/pavings, laid in layers not exceeding 15 cm thick, spread, levelled and rammed/ rolled including watering to required level and gradient.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out and getting out in any type of soil.

Returning filling under floor including spreading, watring and well ramming in layer n.exc 25cm each in any type of soil.

Removing excavated material exc 250m and depositing where directed at a level n exc 500 m above the starting point.

M&L for PCC 1:4:8 type D-2(40mm graded aggregate) in foundation , sub base, filling and mass concrete.

M&L for Brickwork old size with fly ash bricks, straight or curved on plan exc 6m mean radius, built in in cement mortar (1:6)

M & L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 , finished even and smooth without using extra cement

M&L for preparing new plastered surfaces and applying Two coats of cement base paint over a coat of alkali resistant primer on surfaces of walls.

M&L for Roof trusses (framed), trussed,purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.Fe-410-W(Gde-E-250)quality-B

M&l for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming toI. S.1161-1979 grade St.-240 ®.

M&L for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof overing/cladding to wall, fixed with self tapping screws as specified

Preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer.

M&L for Hardcore of broken stone of gauge n exc 63mm deposited, spreaded & levelled in layers n exc 15cm thick including watering and ramming etc complete.

M&L for 75 mm thick plain cement concrete 1:4:8 type D2, using 40 mm graded stone aggregate as in sub base all as directed.

M&L for Stone sett flooring with stone setts of size 200 to 250mm long, 150 to 200mm wide and 150mm deep and sides dressed; bedded in cement mortar 1:3, joints 20mm thick; grouted in cement mortar 1:2 with an admixture of metallic floor hardner 5% by weight of cement and struck flush

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand;complete all as specified and directed by Engineer-in-Charge

M&L for 150 mm bore Reinforced cement concrete pipe,type NP-2,haunching against the sides of pipe in PCC 1:4:8 type D-2 using 40 mm graded machenically crushed stone aggregate and making necessary connection after cutting into existing sewer line/manhole to make it functional complete all as specified as following. Note: (i) Cutting into existing sewer line/manhole shall be measured and paid seperately. (ii) Excvation & earthwork shall be measured & paid seperately.

M&L for Plain Cement Concrete Type B0 1:2:4 type B-0 using 12.5 mm graded mechanically crushed stone aggregate as in cills,stpes,bands ,coping,bed plates,kerbs,hold fasts block etc including weathering, slightly rounded or chamfered angles and throating including formwork complete all as specified.

M&L for Plain Cement Concrete 1:3:6 type C-2 using 20 mm graded mechanically crushed stone aggregate as in surface chanel & drain etc complete all as specified.

M&L for Plain Cement Concrete 1:4:8 type D-2 using 40 mm graded mechanically crushed stone aggregate as in foundation,filling and mass concrete or similar work etc complete all as specified.

M&L for old size brick work with fly ash bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6 complete all as specified.

M&L for 15 mm thick rendering on fair faces of brick or concrete surfaces in cement mortar 1:6 with finished even and fair with out using extra cement complete all as specified and directed .

M&L for 10 mm thick rendering on fair faces of brick or concrete surfaces in cement mortar 1:4 with finished even and fair with out using extra cement with and including water proofing compound @3% by weight of cement all as specified and directed .NOTE- Supply only integal water proofing compounnd shall be measured and paid separately

Supply only integral water proofing compound confirming to IS -2645-1975 all as specified and as directed.

M&L for pre-cast cement concrete 1:2:4 type B-1 using 20 mm graded mechanically crushed stone aggregate as cover slabs for drain and manhole including necessary formwork complete all as specified and as directed.

Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips

Cutting in to existing manholes for connecting new drains 150 mm internal dia of making good to pipe and rendering cutting out existing benching for and foRming branch channel (1/2 round or 3/4 round section) in cement concrete 1:2:4 type B1, smooth finished and reforming benching as required

S & F PVC (SWR) Soil, waste and vent pipes 110/100 mm bors single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F PVC (SWR) bends any radius for 110/100 mm bors of pipe complete all as specified and directed.

S&F Mild steel Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and imilar small articles conforming to Fe-290 Gde-E-165

M&L mild steel Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

S&F of cook house stainless steel openable cover top grease trap of grade-304 ,2.0 mm thickness of size 3.0 mtrx1.50 mtrx0.90 mtr including inlet/oulet of dia 100/150 mm with 03 partition chamber of stainless steel MH cover of size 0.90x0.90 with hinge consists of waste screening chmaber,sludge collection chmaber and waste/sludge removal chamber etc complete including connections and installation at site as deirected by Engg-in-Charge and manufacturer's instructions.

M&L for point wiring complete on surface of wall (open) type with two runs of 1.5 sq mm for phase and neutral single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLSH cable drawn in and incl PVC Casing and capping ISI Marked with its accessories with provn of PVC boxes and fixed with brass screws cup washer for fixing switches/socket/regulators etc incl 1.5 sq mm single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLSH cable as earth continuity conductor to common earth & connecting to earth dolly for the following, all as specified and directed. Note : 1. Proper colour coding shall be adopted for wiring (For Phase- Red, Yellow, Blue, For Earth - Green and For Neutral- Black) 2. All points are required to earthed upto fixtures i.e. Holders, Tube lights, Wall lights, bulkhead lights, bldg security light etc

One light point controlled by switch 5 Amp single pole one way

One fan point controlled by switch 5 Amp single pole one way

One 3 pin 5 Amp socket outlet on same board controlled by one, one way 5 Amp switch

S&F switch piano flush type single pole, one way 5/6 Amp etc complete all as specified and directed by Engineer-in-Charge

S&F Socket 3 pin 5/6 Amp etc complete all as specified and directed by Engineer-in-Charge

Supply & fixing lamp holder (Angular/Straight ), insulated body, with back plate for batten fitting etc complete all as specified and directed by Engineer-in-Charge

S & F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as required etc complete all as specified and directed by Engineer-in-Charge.

M&L for ceiling rose 3 terminal / PVC / polycarbonate, isolated body etc complete all as specified and directed by Engineer-in-Charge

S & F in replacement double door Sheet metal enclosures factory made DBs 4 way SPN, 240 volts ,protection class IP-42, suitable for fixing of MCBs, etc, Concealed in wall confirming As per IEC 61439-3 ,Suitable for Flush Mounting and Surface Mounting, With 100 A Copper Busbar ,With Neutral bar, Earthbar and Cable ties for Cable management,Fully shrouded Neutral bars, Prefitted masking sheet complete all as specified and as directed. Make: Legrand ,Cat No:5076 10 or equivalent in Simens/ Hager/ L&T

Supply & fixing MCB , SP, AC, 240 Volts of 06 to 40 Amp capacity 10KA, 'B' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge.

Supply & fixing MCBs, SPN, AC, 240 volts of 40 Amps capacity 10 KA, 'C' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge

Supply and fix ultra slim square profile LED lighting fixture , environmental friendly, energy efficient ready to use pack Aluminium housing LED Tube light fitiing 22 Watt with LED light source 6500 K,input voltage 140V-270V with uniform light output, with all accessories including its connection with and including 2 core sheathed copper conductor cable of size 0.5 Sqmm with complete with all accessories etc complete all as specified and directed by Engineer-in-Charge

S&F in replacement energy saving and environmental friendly long life LED street light 25 Watt (Bldg security light) made up of pressure die cast aluminium housing with mild power LED as lighting source,surge protection upto 4 kv and PC cover having TOP Opening seperate driver compartment with IP65 protection and impact resistance of IK07 fixed on wall with GI pipe of suitable dia and all fixing accessories including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230V , 50 HZ etc complete all as specified and directed by Engineer-in-Charge

M & L for Supply,laying ,connecting ,testing and commissioning and jointing , LT underground cable in replacement ,1100 volts grade, XLPE insulated, armored with galvanized round steel wire or steel strip, electric power cables heavy duty, with multi stranded aluminum conductor, laid in ducts, fixed on poles/walls with proper size saddles and clamp complete all as specified and as directed by the Engineer-in-Charge of following Sizes :- (a) LT cable10 Sqmm, 2 core. Note : Excavation, Earthwork & cable protection shall be measured and paid seprately under relevent item this Sch.

Excavation in trenches n. exc 1.5 m wide and n. exc 1.5 m in depth and getting out in soft/loose soil etc complete all as specified and directed by Engineer-in-Charge

Supply &lay DWC pipe 50 mm bore for laying of LT cable complete with all accessores etc complete all as specified and directed by Engineer-in-Charge

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground. Earth pit not less than 2.25 m depth and top edge of the earth plate not less than 1.5 m below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of nuts, bolts & washer etc. Earth wire connected upto main earth point / DBs alongwith 15mm dia earth protection pipe from top edge of the earth plate to main earth point to be connected and 20mm dia watering pipe light grade with funnel and provn of PCC using cement concrete (1:2:4) mix type B1 using granded stone aggregate and RCC pit cover 50 mm thick precost RCC (1:2:4) mix type B1 duly reinforced with 8 mm dia of TMT bar @ 100 mm CIC, both way, lifting arrangement complete including all necessary earth work etc complete all as specified and directed by Engineer-in-Charge

Supply and fixing ceiling fan complete with fan blades, down rods. with Remote control accessories of low voltage starting 140 Volts, 1200 mm sweep,Speed of fan 350 RPM(+/-10%) ,Rated Wattage 26(+/-10%) Watt , minimum air delevery 220 CMM ,Winding material super enamelled copper wire ,Class of Insulation ''B'', Power factor 0.98 Min with service value 6.00 BEE five star,230V rated with brushless direct current motor ( BLDC) ,complete all as specified and directed.

S&F 15 mm bore self closing basin push pillar taps in round shape, Cast Copper alloy, chromium plated, screwed for iron pipe and fixed in repair.Make Model PRS -CHR 031 of Jaquar or in equivelent Hindware,Parryware ,cera etc.

Supply and fix stainless steel plate racks of size 610 x 610 x 254 mm conforming CatPart No SSKPR-310 of silver shine or of equivalent model nearest size in other makes. Make : Parayag, Nirali or Bluestar as approved by GE.

M/s AG PATHAN (BID ID -3103848)

M/S. YADAV ENTERPRISES (BID ID -3122148)

Ms. M.D. Auty (BID ID -3108055)

AZAD SERVICES (BID ID -3108296)

M/S. M. F. Sharif & Co. (BID ID -3122459)

M/S-B.R.SONAWANE (BID ID -3108977)

MS. G.A. CONSTRUCTION (BID ID -3109092)

M/s. N D Karande (BID ID -3111367)