COMPREHENSIVE MAINTENANCE OF HIGH MAST LIGHT, CHILDREN PARK LIGHT, GATE LIGHT, FOUNTAIN LIGHT ALONGWITH REPLACEMENT OF UNSV 230 VOLT AUTO DAY/NIGHT ON OFF SENSOR SWITCH AND CERTAIN MISC WORK AT 39 WING AF STATION UDHAMPUR

Amount

Supply and Laying Cable XLPE insulated screened PVC bedded galvanized steel strips or wire armoured, cables (heavy duty) ISI marked with stranded aluminium conductor, 1100 volts grade and connecting and testing in trenches, under floors/ roads or on walls complete including taking down old complete all as specified and directed of following sizes :- (Note 1.: Earth work, excavation shall be measured & paid separately under respective item of Schedule and wherever cable laying on walls and uses of thimbles etc rates shall deemed to be included in the quoted rates). make- Havells/Gloster/Polycab

6 Sqmm, 2 Core

10 Sqmm, 2 Core

10 Sqmm, 4 core cable

25 Sqmm, 3½ core cable

35 Sqmm, 3½ core cable

Excavation in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for laying of cable and foundation of poles, stays and getting out in any type of soil,complete all as specified and as directed by Engineer-in-Charge.

Returning filling in including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick each layer in any type of soil complete all as specified and as directed by Engineer-in-Charge.

Removing surplus excavated material to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete, all as specified and as directed by Engineer-in-Charge.

M & L for Sand cushioning to underground cable, provided with a layer 8 cm before and 15 cm after laying and stretching jointing and testing the cable all as specified and directed. by Engineer-in-Charge. Note: Punned thickness of sand shall be measured.

Common burnt sub class ‘B’ brick laid flat in trenches over and across the length of cable with length of brick perpendicular to the direction of cable adjacent/abutting each other complete all as specified and directed for cable protection.

LT Cable junction box outdoor shall be made out of Polycarbonate with glass fiber reinforced than 205mm x 255mm x 112 mm(the cable size upto 25 sqmm). The polycarbonate junction box shall be environmental friendly, recyclable, halogen & silicon free, anti acid & anti corrosive. The Junction Box shall be rated for Degree of ingress Protection IP 66 in accordance with IEC 60529.Weatherproof, UV resistant. The gasket material of junction box shall be Polyurethane and the gasket shall be internally embedded. The Junction Box shall be complies with requirements of the standards IEC 60998. The Junction Box with 25 Amp Connectors or Terminal Trip or Bus Bar. The Junction Box / Enclosure shall be tested as per IEC including one No. 4 pole connector and one No MCB SP 'C' curved 6-32 Amps and chromium plated clamps and nut bolts, cable glands or cable grommets with lock nuts of 2 Nos for each box complete all as per manufacturer’s Make : Cat Part :- DK 2500 B of Hensel or equivalent of Siemens/GE Power/Rittal/Legrand as approved by GE.

Supply and fixing of GI tubing light grade 50 mm bore cut to size and making the pole for the garden light including execavation, returnig filling and removing of soil etc/road cable protection including cutting of road etc and making good all as specified and directed by Engr-in-Charge.

Supply and fixing of GI tubing light grade 80 mm bore cut to size and making the pole for the garden light including execavation, returnig filling and removing of soil etc/road cable protection including cutting of road & making good surface etc all as specified and directed by Engr-in-Charge.

Supply and fixing of DWC HDPE tubing 50 mm bore for open/underground laying cable, cut to size and making the tubing for cable protection including cutting of road etc/cutting of PCC and making the good surface complete all as specified and directed by Engr-in-Charge. Note for item no 10 and 11 :- (a) The using of GI Clamp in the wall/drainage rate are deemed to be included in the quoted rate. (b) The insulation of DWC pipe should be of high that does not deteriorate with UV rays/ heavy sun rays/winter season etc. (c) Drawing existing cable through DWC pipe shall be deemed to be included in the quoted rates.

Supply and fixing of DWC tubing 80 mm bore for open laying cable,cut to size and making the tubing for cable protection including cutting of road etc/cutting of PCC and making the good surface complete all as specified and directed by Engr-in-Charge.

Supply & installation and testing & Commissining CPRI approved Timer panel outdoor type, cubical type IP 54 suiable for 415V, 3 phase 50 Hz , AC supply system, dust,weather & vermin proof, made of 3.15 mm thick CRCA sheet, Bottom base channel of MS section not less then 45 mm x 45 mm x 5mm thick, shell having TPN copper busbars of rating 100 Amp Cap.complete with 4 nos mounting legs made out of 40 mmx40mmx5 mm angle iron grouted in PCC block of size 30cmx30cmx90cm (30cm depth below ground level and 60 cm above ground level) in cement concrete 1:3:6 ,type C-2 (using 40 mm grade crushed stone aggregate),and connection with suitable size of aluminium thimbles,nuts,bolts and washers ,double door system lockable/openable by key, cable entry with glands, foundation/grouting on & including PCC as per site requirement complete all as specified and directed by Engr-in-Charge.

Supply and fixing of LED Post Light, 50 Watt, IP 65 LED post top with aluminium enclosure, powered with high power LEDs as light source and die casted heat, symmetrical light distribution and excellent heat dissipation for outdoor illumination for gate lights including cutting/chassis and fixing arrangement in the cement pillar with pole dia 40 to 80 mm with the help of fixing arrangement for nut, bolt, fastner etc all as directed by Engr-in-Charge. Make :- JUPITERMAXIPT50WLED830PSYMTOPC of Havelss or equivalent to HPL/Bajaj/Phillips/C&S etc.

Supply and fixing of Cone Round Post Top Lantern 25 Watt, IP 65 LED post top, symmetrical light distribution, spun aluminium landscape luminaire, refer to the use of outdoor illumination for gate light for diffused lighting with high power LED as light sources, offers uniform luminaire for different applications including cutting/chassis and fixing arrangement in the cement pillar with pole dia 0 to 80 mm with the help of fixing arrangement for nut, bolt, fastner etc all as directed by Engr-in-Charge. Make : Cat Part No cat part No HPLLEDPCR25W of HPL/CORALPT25WLED757PSYMTOPC of Havells or equvalent to bajaj/philips/C&S

Supply only moderna desktop Rechargeable light, 4 watt, LED type cable. Make :- Havells code No :- LHEXBZP7CN1W004 or equivalent as approved by GE.

Supply and fixing of Round Bollard 600 mm, 9 Watt, with metal body, suitable for bulb LED, IP 54 (Bulb 100 Lm/w), energy saving, environmental friendly, long life aesthetically designed aluminium landscape refer to the use of outdoor illumination for garden light for diffused lighting with high power LED as light sources including cutting/chassis and fixing arrangement in the cement pillar/PCC cube/Wooden Bamboo etc with the help of fixing arrangement for angle, fastner etc all as directed by Engr-in-Charge. Make : Cat Part No HPLLEDB9W of HPL or equvalent to Havells/bajaj/philips/C&S Note for Item No 16 & 17 :- (a) Bulb temperature warm white/cool white shall be provided as directed by Engr-in-Charge. (b) All civil/electrical work & material is deemed to be included in the quoted rates.

Supply and fixing of Pyramid Top Bollard 12 Watt (Round/Square) Milky diffuser with suitable for bulb LED, IP 54 (Bulb 100 Lm/w) refer to the use of outdoor illumination for garden light for diffused lighting with high power LED as light sources including cutting/chassis and fixing arrangement in the cement pillar/PCC cube/Wooden Bamboo etc with the help of fixing arrangement for angle, fastner etc all as directed by Engr-in-Charge. Make : Cat Part No HPLLEDBPR12W of HPL or equvalent to Havells/bajaj/philips/C&S

Supply and fixing of LED 9 watt Spike light refer to the use of outdoor illumination for Park/garden for diffused lighting with high power LED as light sources including cutting/chassis and fixing arrangement in the cement pillar with the help of fixing arrangement for angle, fastner etc all as directed by Engr-in-Charge. Make : Cat Part No HPLLEDSP0960 of HPL or equvalent to Havells/bajaj/philips/C&S

Supply and fixing of Globe for Park light/decorative gate light made up of high grade unbreakable polycarbonate material suitable for retrofit LED lamp of pole dia 40 to 80 mm, width of globe 150 mm and height appx 182 mm including cutting/chassis and fixing arrangement in the cement pillar/GI tubing/wooden bamboo etc with the help of fixing arrangement of nut, bolt and washer etc and electric connection to the lamp complete all as specified and directed by Engr-in-Charge.Make : Cat Part No LHFXBON1TN5Q008 of Havells or equivalent to HPL/bajaj/philips/C&S

Supply and fixing of Globe for Park light/decorative gate light made up of high grade unbreakable polycarbonate material suitable for retrofit LED lamp of pole dia 40 to 80 mm, width of globe 200 mm and height appx 227 mm including cutting/chassis and fixing arrangement in the cement pillar/GI tubing/wooden bamboo etc with the help of fixing arrangement of nut, bolt and washer etc and electric connection to the lamp complete all as specified and directed by Engr-in-Charge.Make : Cat Part No LHFXBON1TN5Q014 of Havells or equivalent to HPL/bajaj/philips/C&S

Supply and fixing of Globe for Park light/decorative gate light made up of high grade unbreakable polycarbonate material suitable for retrofit LED lamp of pole dia 40 to 80 mm, width of globe 242 mm and height appx 250 mm including cutting/chassis and fixing arrangement in the cement pillar/GI tubing/wooden bamboo etc with the help of fixing arrangement of nut, bolt and washer etc and electric connection to the lamp complete all as specified and directed by Engr-in-Charge. Make : Cat Part No LHFXBON1TN5Q020 of Havells or equivalent to HPL/bajaj/philips/C&S

Supply and fixing of warm flood light 60 watt, IP 66 refer to the use of outdoor illumination for garden light for symmetrical light distribution with high power LED as light source including fixing arrangement with base plate and suitable size as directed by Engr-in-Charge. Make : Cat Part No HPLLEDFL06060FWW of HPL or equvalent to bajaj/philips/C&S

Supply & installation and testing & Commissining CPRI approved outdoor cubical type IP 54,LT feeder piller box suiable for 415 V, 3 phase 50 Hz , AC supply system, dust,weather & vermin proof, made of 3.15 mm thick CRCA sheet, TPN copper busbars of rating 200 Amp Cap.Bottom base channel of MS section not less then 45mmx45mmx5mm thick, entire panel shall have a common aluminium earth bar of size 25mm x5mm at the rear with 2 no earth stud,double door both side opening single door system lockable/openable by key from both sides having flush pattern fancy locks with louvers. cable entry with glands, foundation/grouting on & including PCC as per site requirement with the following :- (a) Bus bar electrolytic grade copper and supported on Non-hygroscopic, non carbonising, corrosion resistance SMC insulator 200 Amp,4 pole, not less then 45 CM long mounted on insulators for incoming supply - 1 Set (Set of 4 strips) (b) Phase indicator lamp RYB LED type - 1 Set (Set of three). (c) Digital Voltmeter & Ammeter - 02 Nos (d) CT Ration 100/05 CL 1.0 Tape Wound - 01 Set (Set of three) Incoming: (a) MCCB 160 Amp, 415V, 50 Hz, FP, ,25 ka, Ics= 100% Icu fixed type, complete all as specified and directed by Engr-in-Charge. Note :- 1. Panel shall be installed at least 60 cm above ground 2. All civil/electrical work & material is deemed to be included in the quoted rates

M&L for insulated tape of size 25 mm width , 20 Meter long and 1 mm thick complete all as per directed.

Supply and fix 250 watt LED flood light, with IP 66 protection, PF>= 0.90, lumen efficacy >= 100 lumen/watts, 5700 K, light luminaire engergy saving, environmental friendly long life with high power led as light source suitable for highlighting architectural feature or area lighting also suitable to rough services /installation incl taking down old one etc complete as specified and directed Make- Wipro cat part No LF20-342-060-57-XX or equivalent HPL/Havells/CG etc as approved by GE

Supply and fixing of Integral LED aviation light, 2x 100 wattage luminaire in yellow die-cast alluminium alloy housing with red coloured polycarbonate dome of twin lights (as feature if one lamp light failure than other continues supply) as cat part No BJAOL 1-75 Aviation obstruction light with Neon Lamp of make Bajaj or equivalent of LED of C&S/CG/Phillips as approved by GE including necessary electric connection with suitable size of PVC copper cable as per manufacture's requirement on towers/Chimney/Hanger of approx height 40 to 50 Mtr alongwith necessary arrangement of ladder/hydra etc complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing of Integral LED aviation light, 302 wattage, luminaire in yellow die-cast aluminium alloy housing with red coloured polycarbonate dome of single light as cat part No BGAV 302 LED of make Bajaj model no 110731or equivalent C&S/CG/Phillips including necessary electric connection with suitable size of PVC copper cable as per manufacture's requirement for installation on towers/Chimney/Hanger of approx height 40 to 50 Mtr alongwith necessary arrangement of ladder/hydra etc complete all as specified and as directed by Engineer-in-Charge.

Supply and fix 1.5 Sqmm 2 core cable, PVC insulated and PVC round sheathed, copper conductor(flexible) industrial cable, 1100 volt, confirming to IS :694 including replacement of old unsv cable. Make :- Shalabh/Havells or equivalent as approved by GE.

Material and Labour for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate in coping etc for pole including necessary form work for fair finished exposed concrete surfaces complete all as specified and directed.

M&L for type C2 1:3:6 (40 mm graded aggregate) cement concrete in foundation and mass concrete etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for MCCB 4 Pole, 415 V, fixed type, ICS100% of ICU, 100 Amps with breaking capacity 16 KA complete all as specified and directed. Standard/Havells/Legrand or equivalent as approved by GE.

Material and labour for MCCB 4 Pole, 415 V, adjustable type, ICS100% of ICU, 160 Amps with breaking capacity 25 KA complete all as specified and directed. Standard/Havells/Legrand or equivalent as approved by GE.

Supply and fix heat shrinkable End termination kits and accessories of following capacities and type:-Make :- 3M/Denson or as approved by the GE. Note for item No 34(a) to 34(d) :- Rate for the execavation, returing filling and removing of the earth work and provide labour and Electrician shall deemed to be included in the quoted price, not extra be paid for this items.

Outdoor/indoor 16 to 25 Sqmm 3.5/4 core cable jointing kit for 1.1 KV grade cable

Outdoor/indoor 35 to 50 Sqmm 3.5/4 core cable jointing kit for 1.1 KV grade cable

Outdoor/indoor 70 to 120 Sqmm 3.5/4 core cable jointing kit for 1.1 KV grade cable

Outdoor/indoor 150 to 185 Sqmm 3.5/4 core cable jointing kit for 1.1 KV grade cable

Supply and fix heat shrinkable straight through joint kit and accessories of following capacities and type:- Make :- 3M/Denson or as approved by the GE. Note for item No 35.01 to 35.05 :- Rate for the execavation, returing filling and removing of the earth work and provide labour and Electrician shall deemed to be included in the quoted price, not extra be paid for this items.

Straight through joint kit indoor/outdoor al conductor cable of size 10 to 16 Sqmm and 3.5/4 core

Straight through joint kit indoor/outdoor al conductor cable of size 25 to 35 Sqmm and 3.5/4 core

Straight through joint kit indoor/outdoor al conductor cable of size 50 Sqmm and 3.5/4 core

Straight through joint kit indoor/outdoor al conductor cable of size 95 Sqmm and 3.5/4 core

Straight through joint kit indoor/outdoor al conductor cable of size 120 to 150 Sqmm and 3.5/4 core

Laying only LT UG cable 10 sqmm x 4 core to 185 sqmm x 3.5 core cable shall be provided under Sch 'B' making all electrical connections as directed by Engr-in-Charge.

Repair/maint and overhauling of L.T.Panel 3 phase AC 415V, 50 Hz A of any make including Taking out old /UNSV MCCBs & MCBs /incoming and outgoing laminated copper busbar , DMC/epoxy insulators of any size ,Volt meter, Amp meter, phase indicator LED lamp,Change over switch of any capacity ,burnt out copper winding ,current coil ,potential coil and keeping aside for safe custody for re-use, opening the L.T. Panel, removing gasket, dismantling and taking out old parts carefully, disconnecting all conections, & re-assembling all serviceable parts to original position including cleaning , removing sludge, dirt, dust, cleaning of parts including removal of old paint with 02 coat synthetic enamel machine spray paint after 01 coat iron red oxide machine spray paint along with replacement of unsv nuts, bolts, thimbles, gasket etc as per site requirement including denting, welding and replacement of unsv hinges if requirement complete testing all as specified and directed by Engineer-in-Charge. Note : (a) All spare parts and control wiring will be measured and paid seperately under respective item of Sch 'A'. are as under. (b) Denting, welding, replacement of unsv hinges, locking arrangement, handle, unsv gasket, cable gland, nut, bolt, washer, minor repair of PCC foundation if required and removing of old paint alongwith reassembling, testing, commissioning etc shall be deemed included into the quoted rate.

MCB TPN capacity 32 Amps, 415V, 50 c/s 16 KA-01 No. Make : Legrand / Schnieder / L&T

MCB SPN capacity 32 amp, 'C' series-02 Nos Make : Legrand / Schnieder / L&T

Set of indicating lamp LED type-01 Set.

Civil work PCC 1:2:4 for grouting of panel complete Size- (0.25x0.25x0.25 cum x 04) including excavation, earth work.

Copper insulated bus bar with DMC/porcelain insulator etc made out of laminated as per existing size 40mmx5mm

Copper insulated bus bar with DMC/porcelain insulator etc made out of laminated as per existing size 50mmx6mm

Current transformer of suitable size as per existing

M&L for cutting the existing cable from loop and existing panel and making sleeves over the existing cable suitable for LT U/G cable of size 25 to 50 Sqmm.

Copper wiring 2.5 Sqmm as per existing size

M&L for Weather proof outdoor bus bar chamber wall mounted, made out of 1.6 mm thick MS sheet comprising of Copper strips each of 250 Amps, 4 Nos Cu Bus Bar,appx 60cm long duly insulated mounted on insulators including complete with all accessories and connections with copper thimbles, nuts, bolts & washers including cable glands at entry and outlet points including taking out old unserviceable bus bar chamber complete all as specified and directed by Engr-in-charge. Make :-Havells cat part No IHBC025004 or equivalent as approved by GE.

M&L Earthing complete as per electrical plate No 3 of MES SSR Part I with galvanised steel plate earth electrode 60 cm x 60 cm x 6.0mm, burried directly vertically in ground in a pit of depth not less than 2.5 metres below ground level with the top edge of earth plate at a depth not less than 1.5 m below normal ground level connected to and including galvanised iron or steel earth strip 25x4mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel. Earthing wire protected by galvanised iron or steel pipe 50 mm bore medium grade and connected to continuous earth wire on pole/ test point. Watering pipe shall be 20mm bore GI medium grade. The earthing shall be inclusive of excavation and earth work in any type of soil,charcoal, salt,funnel , PCC pit and RCC cover complete all as specified & directed. Note 1- following items deemed to be included in quoted rate :- (a) Earth electrode. (b) Main earthing lead from earth electrode to test point and further to equipment to be earthed upto 7.5 metre. (c) Material and labour for connecting earth electrode and earthing lead as specified. (d) Adequate quantity of charcoal dust and common salt as per direction. (e) All labour involved including testing of earth net work. (f) Excavation and earth work or drilling hole for electrode. (g) P.C.C. pit and C.I. cover. (h) Funnel with watering pipe, wire mesh and copper lugs etc. as specified. (j) G.I. protection pipe of size ordered specified for protection of earthing lead from mechanical injury or tempering. Note 2 - On testing after completion if the desired earth resistance is not obtained the earthing will be redone at no extra cost.

Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles with the help of insulator or any other indicated situation for loop earthing etc, and provision of GI nuts, bolts washers etc wherever required and making joints as required 25x4 Galvanised Iron strip coplete all as specified and directed by Enginer-in-Charge.

M & L for 3.15 mm CRCA MS Sheet for fixing of broken cover to panel etc with 02 (two) coat Machine spray paint over one coat red oxide primer/paint alongwith fixing arrangement through nut, bolts or welding etc suitable for panel base plate or panel canopy all as specified and directed by Engineer-in-Charge

shivom builders

ASIA BUILDER