REPAIRS TO HARDSTANDING, BRICK WORK, RETAINING WALL, BOUNDARY WALL, COMPOUND WALL, CHAIN LINK FENCING, BOUNDARY PILLARS AND PPGL SHEETS IN AOP AREA, WING III AND GOSWAMI ENCLAVE UNDER GE NASIK ROAD.

Amount

Demolition of concrete in ground floors and pavings n exc 15cm thickness (below or above ground level).

100 mm thick sub-base with cement concrete type D-2, 1:4:8 (40mm graded aggregate). Note : Mixing of concrete using machine only.

M&L for 100 mm thick concrete flooring with cement concrete type B-2, 1:2:4 (40mm graded aggregate) over and including provision of pvc diviging strip for joints. Note : Mixing of concrete by machine only.

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand;over and including provision of PCC 1:2:4 type B0 as in filleting/edging to the sides of paver path/hardstanding in size and shape where ever required as per standard engineering practice to the entire satisfaction of engr-in-charge.

M&L for coloured 10-15 mm thick heavy duty,antiskid vitirified tile as in flooring,parking,ramps etc over and including 20 mm thick screed bed in CM 1:6,set and jointed in neat cement slurry and pointed in white or coloured cement to match,over and includng dismantiling old tiles. Note:Size,finish(glossy/matt),shade,pattern of tile shall be approved by GE based on manufacturing company catalogue.contractor quotated rate deemed to be inclusive of tile of size 40cmx40cm(maximum).

M&L for Chequered cement concrete tiles with grey cement and pigment 30cm x 30cm x 25mm thick, with rubber moulded glossy finished surface, laid in floors over and including 15mm thick cement mortar screed bed in cement mortar 1:6, set jointed and pointed in neat cement slurry in floors.over and including provision of PCC 1:2:4 type B0 as in filleting/edging to the sides of paver path/hardstanding in size and shape where ever required as directed by engr-in-charge.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar.

M&L for Rough Shahabad stone 25 mm to 30 mm thick in flooring/plinth set and jointed in in neat cement slurry and pointed in CM 1:4 complete all as specified and directed over and including 15mm thick screed bed in cement mortar 1:6 and incl provision of PCC 1:2:4 type B0 as in edging/sides of shahabad stone flooring/ plinth protection wherever required as per standard engineering practice to the entire satisfaction of engr-in-charge.

M&L for 18 to 20mm thick Granite of any type work (table rubbed and polished) in steps, jambs pillars, window cills cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture re of pigment to match with shade of granite 18 to 20mm thick all as specified and directed.

Dismantling of precast concrete articles and precast concrete block set or built in cement mortar.

M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc. Note:work to be executed at any height and situation.

M&L for brick work with fly ash bricks straight or curved on plan exc 6 m mean radius built in CM 1:6 including raking joints on both sides of wall.curing as per standard engineering practices. Note:work to be executed at any height and situation.

Taking down completely cement or cement lime plaster, any description on brick or stone walls/ceiling, etc. including raking out joints, hacking for key, scrubbing down with water, etc. Note:work to be executed at any height and situation.For multistorey bldg Only ladder/sccaffolding shall be permitted to carry out repairs.

M&L for Rendering 10mm thick in cement mortar 1:6 on brickwall/concrete surfaces finished fair and even.curing as per standard engineering practices.

M&Lfor rendering 15 mm thick in cement mortar 1:4 on brick wall /concrete surfaces finished fair and even. Note:work to be executed at any height and situation.For multistorey bldg Only ladder/sccaffolding shall be permitted.

M&L for rendering 5 mm thick in cement mortar 1:3 on ceiling surfaces finished fair and even.

M&L for applying two coats of exterior emulsion paint on wall/ceiling surfaces including preparation of surfaces. Note:work to be executed at any height and situation.for multistorey bldgs only sccaffolding/ladder shall be used.

M&L for preparation of plastered surfaces of wall/ceiling and Distempering with 1st quality(as per manufacturers catalogue) acrylic distemper(ready mixed) having VOC content less than 50gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats as directed by engr-in-charge.

M&L for Two coat of cement based paint on walls/ceiling including preparation of surfaces by brooming down or steel wire brushing scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots,washing removing nails,removing vegetation growth of any size and penetration on wall /ceiling surfaces to the entire satisfactin of ground executives sealing holes,cracks of any with/depth using crack sealing compound(premium quality) using gun.curing as per standard engineering practices. Note:for multistorey bldgs only sccaffolding/ladder shall be used.work to be executed at any height and situation.

M&L for Providing, cement concrete type B1 1:2:4 (20 mm graded aggregate) in copings and the like including weathering, slightly rounded or chamfered angles and throating, as directed and finnshing the surfaces of concrete.

Demolition of concrete in any description and in any position.

M&L for Providing cement concrete type D2 1:4:8 (40 mm graded aggregate) in foundations, filling and mass concrete.curing as per standard engineering practices. Note: Concrete is to be done using mechanical/ machine mixing.

Dismantling of stone/boulder masonry, laid dry in pitching.

M&L for stone/ boulder pitching, hand packed tightly and grouted with cement and sand mortar 1:6 including raised pointed in cement mortar 1:4 (including dressing and levelling the surface).curing as per standard engineering practices.

Dismantling barbed wire fixed to any type of standard rails straining bolts (each line wire to be measured).

Dismantling RCC posts or struts any section, embedded in concrete, brick work, masonry etc. including taking out embedded portion and making good disturbed ground.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth round, in layers not exceeding 25 cm in soft/loose soil.

S&F mild steel Posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165.

M&L for Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 5cm but n exc 10cm and diameter of neck 5 to 10 mm.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire.

Supply only chain link MS galvanised fencing, any size or type.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips for fixing chain link fencing etc.

M&L for Preparation of new or previously untreated steel or iron surfaces over 10 cm width or girth not otherwise described and two coats of synthetic enamel paint over a coat of al red oxide primer. Note : work is to be executed at any height and situation.

Dismantling wrought iron or mild any description such as steel gate, steel frame works, purlins, rafter, railings, balusters and window guard bars and directed by Engr-in-Charge. Note : work is to be executed at any height and situation.

S&F Framed work as in grill, doors or gates of angle or other section with gusset plates, braces, etc, complete, drilled for fixing of steel sheeting or other covering, Doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing Fe Grade 290(Gde E-165) complete all as specified and directed by Engr-in-Charge. Note : work is to be executed at any height and situation.

S&F steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1998 Grade St-240 complete all as specified and as directed. Note: work is to be executed at any height and situation.

Dismantling Plain or corrugated steel sheeting of any gauge,thickness,including Nainital or similar pattern roof coverings complete all as specified and as directed. Note: work is to be executed at any height and situation.

S&F Prepainted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength 550 mpa as in roof covering/cladding to wall,fixed with self tapping screw complete all as specified and as directed. Gap between wall face and sheet if any shall be sealed using CM 1:3 with WPC.quoted rate deems to be inclusive of the same. Note:work is to be executed at any height and situation.

S&F Prepainted Galvalume aluminium zinc coating GI based Plain sheet 0.50 mm thick of any colour having tensile strength 550 mpa as in roof covering/cladding to wall,fixed with self tapping screw complete all as specified and as directed. Note:work is to be executed at any height and situation.

M&L for preparation of old surfaces of walls/ceiling by brooming down or steel wire brushing;washing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots;washing, removing nails,removing vegetation growth of any size and penetration wall/ceiling to the entire satisfaction of ground executives, sealing holes,cracks of any width/depth using waterproof crack sealing compound of premium quality as approved by GE and applying one coat of exterior emulsion paint on walls/ceiling. Note: for multistorey bldgs only sccaffolding/ladder shall be used.work to be executed at any height and situation.

M&L for complete removal of existing treatment to wall/ ceiling by brooming down or steel wire brushing;washing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots;washing, removing nails,removing vegetation growth of any size and penetration on walls/ceiling to the entire satisfaction of ground executives,sealing holes holes,cracks of any width/depth by waterproof crack sealing compound as approved by GE and applying two coat of exterior emulsion paint on walls and ceilling surfaces. Note:for multistorey bldgs only sccaffolding/ladder shall be used.work to be executed at any height and situation.

M&L for applying two coats of exterior primer on wall/ceiling surfaces as per manufacuters instruction including preparation of surfaces to the entire satisfaction of ground executives. Note : For multistorey bldgs only sccaffolding/ladder shall be used.work to be executed at any height and situation.

M&L for applying two coats of interior primer over wall /ceiling surfaces as per manufacutrers instruction incl preparation of surfaces to the entire satisfaction of ground executives.

M&L for Repairing of broken edges of RCC chajjas, roof projections, fins, facia and similar works by dismantling of loose and damaged/ disintegrated portion of edges (cross sectional area not exceeding 150 sqcm) with cement mortar 1:4 or cement concrete 1:1½:3 type A0 and chicken wire mesh with nails (to hold fresh mortar/concrete) including necessary formwork etc. and scaffolding for work upto four storied buildings and finishing the surface by paint to the entire satisfaction of engr-in-charge and match the surface with existing work. Note:work is to be executed for multistorey/high rise bldg.repair work shall be carried out using sccaffolding/ladder only.

Taking down carefully existing bituminous membrane/tarfelt treatment any description and cleaning and making good damaged surface of roof ,parapet,facia etc in cement mortar 1:3/PCC 1:2:4 as directed by engr-in-charge where ever require.quotated rate shall be deemed to be inclusive of complete removal of swollen plaster and concrete wherever directed by engr-in-charge and removing rubbish out of defence land. Note: work to be executed at any height and situation.

Demolition of concrete (unreinforced) of any description and in any position not otherwise secifically provided for.

Providing cement concrete type B0 1:2:4(12.5mm graded aggregate) in roof kerbs or mud stops,ridge,padding rounded or chamfered on edges.

M&L for rendering 15mm thick(minimum) in CM 1:4 with intergral waterproofing compound (200 ml per bag of cement used) on roof surfaces,parapets,facias etc .Curing as per standard engineering practice. Note: waterproofing compound shall be measured and paid separately.

Supplying only integral water proofing compound ISI marked complete all as specified and as directed.

M&L for applying evenly a coat of hot blown bitumen 85/25 grade over roof,facia,parapet surfaces at the rate 1.20 kg per sqm for fixing app membrane etc including cleaning surfaces. Note:make of bitumen same as for app membrane.

M&L for Waterproofing on roof including flashing and junctions of parapet,kerb, wall etc.as under :- (a) Laying a layer of APP based polymeric membrane, 3 mm thick(minimum),weighing not less than 3.60 kg/Sqm prefabricated fire layer waterproofing membrane reinforced with polyester non woven fabric(weighing not less than 160 gms/sqm) shall be applied over compatible primer at 0.40 litre/Sqm of density at 25 degree Centigrade 0.87-0.89 Kg /Litre and viscosity 70-160cps or cold sticker, application of APP modified membrance shall be by torch application. The overlaps shall be minimum 150mm on the transverse direction and 100 mm on the longitudinal direction. (b) APP membrance,Primer and bitumastic aluminium paint and bitumen shall be of same brand. (c) For vertical surfaces i.e. parapet etc. app membrane shall be tucked into groove and sealed with silicon sealant i.e. "Dowsil 789 weatherproof silicon sealant" using gun. (d) Bitumen and aluminium paint shall be paid separately.

M&L for applying two coats of solar reflective bitumastic aluminium paint at the rate 0.15 kg/sqm per two coat over exposed app membrane surfaces(old/new) including cleaning of surfaces to the entire satisfaction of ground executives. Make of paint same as of app membrane.

Disconnecting existing tanks exc 250 n exc 500, setting aside (or lowering if required) cleaning and removing all scale dirt,etc from the mouth of circulating pipes etc and hoisting if required,reconnecting and re-fixing in position.

Disconnecting existing tanks exc 500 n exc 1000, setting aside (or lowering if required) cleaning and removing all scale dirt,etc from the mouth of circulating pipes etc and hoisting if required,reconnecting and re-fixing in position.

Taking down AC rain water pipes(any size or pattern) including all fittings,head shoes,bends,swan neck etc. Note: work to be executed at any height and situation.

S&F PVC (SWR) pipes110 mm bore single socketed, in any length with rubber ring joints, laid in trenches or in floors/wall as RWP including fixing clamp.

M&L for dismantling parking/passage tile of any description by removing cement mortar,dirt using muriatic acid,washing and refixing/relaying over and including 20 mm thick screed bed in CM 1:6 and 50 mm sand cushioning wherever required set and jointed in neat cement slurry and pointed in white or coloured cement to match.

NOTE : - AMOUNT OF SCHEDULE OF CREDIT RS. 62,125.00 WILL BE DEDUCTED FROM TOTAL AMOUNT OF BOQ.

M/s. JBSR ENTERPRISES.

sunway associates

Bidder Name

Alpha Construction

sunway associates

M/s. JBSR ENTERPRISES.