PROVISION OF TOILET NEAR ECHS IN RED EAGLE HOUSE, CHAIN LINK FENCING NEAR ECHS, SPECIAL REPAIR TO GOVT MD ACCN NOS T-20 TO T-23 (04 X OR GOVT MD ACCN) TILING WORK IN BLDG NO. P-64/1 TO 12 AT NEW CANTT PRAYAGRAJ.

Amount

Excavation in trenches not exceeding 1.50 m wide and n.exc 1.50m depth for foundation etc or for shafts, walls, cess-pits, manholes, pier holes etc n.exc. 10 sqm on plan and getting out in soft/loose soil complete all as specified and directed.

Excavating in post holes (or similar holes) in soft / loose soil each not exceeding 0.5cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm ,watering and removing surplus soil to a distance not exceeding 50m and making good surface complete all as specified and directed.

Removing excavated materials to a distance n.exc 50 m and depositing where directed at a level n.exc 1.5m above the starting point, complete all as specified & directed.

Removing excavated materials to a distance exceeding 1.5 Km but not exceeding 5 Km and depositing where directed at a level n.exc 1.5m above the starting point, complete all as specified & directed.

Returning, filling in including spreading, levelling watering and well ramming in layers not exc. 25cm thick complete all as specified and directed.

Spreading and leveling excavated approved soil in layers not exceeding 25cm thick including watering and well ramming including watering as required for filling under floor complete all as specified and directed.

M & L for cement concrete 1:4:8 type D2 using 40 mm graded aggregate in foundations, sub base filling and mass concrete complete all as specified and directed

M & L for cement concrete 1:3:6 type C2 using 40 mm graded aggregate in foundations, sub base filling and mass concrete complete all as specified and directed

M& L for Reinforced cement concrete design mix M-25 using 20 mm graded stone aggregates in foundations, footing, plinth beams, bases for columns and mass concrete complete all as specified and directed. Note:- Reinforcement to be measured & paid separately under respective item.

M& L for Reinforced cement concrete design mix M-25 (using 20 mm graded stone aggregates) in columns, pillars, posts & struts complete all as specified and directed. Note:- Reinforcement to be measured & paid separately under respective item.

M& L for Reinforced cement concrete design mix M-25 (using 20 mm graded stone aggregates) in lintels over 1.5m clear span, beams and cantilevers complete all as specified and directed. Note:- Reinforcement to be measured & paid separately under respective item.

M& L for Reinforced cement concrete design mix M-25 (using 20 mm graded stone aggregates) in slabs supported on walls, beams & columns complete all as specified and directed. Note:- Reinforcement to be measured & paid separately under respective item.

M& L for Reinforced cement concrete design mix M-25 (using 20 mm graded stone aggregates) in chajjas complete all as specified and directed. Note:- Reinforcement to be measured & paid separately under respective item.

Form work to sides of concrete foundations, footings, bases of columns, sides & soffits of foundation and plinth beams and similar work for rough finished flat surfaces of concrete complete all as specified and directed.

Form work to sides of square or rectangular columns, pillars, posts and struts for rough finished surfaces of concrete complete all as specified and directed.

Form work to side & soffits of floor or roof beams , beam, shelves including supports, overhang etc rough finished complete all as specified and directed.

Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick, for rough finished flat surfaces of concrete complete all as specified and directed.

Form work to chajjas and similar items including edges for rough finished flat surfaces of concrete complete all as specified and directed.

Form work to edges of concrete flats, openings, floors & roofs and sides of RCC/PCC bands in walls and similar work exceeding 10cm but not exceeding 20cm wide for rough finished surfaces of concrete complete all as specified and directed.

M&L for providing cement concrete 1:3:6 type C-1 using 20mm graded stone aggregate in cills, seismic and other similar bands, plinth courses, copings, bed plates, bond stones, etc including weathering, slightly rounded or chamfered angles and throating as directed including necessary form work complete all as specified and directed.

M & L for PCC 1:2:4 type B1 using 20 mm graded aggregate as in roof, lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

S & F for Mild steel work conforming to Fe 410-0 or Fe 310-0 in nosing to steps including embedding in concrete and screwing etc, wind ties for roof including securing bolts, posts & struts in fencing including cutting top to shape as directed, drilling holes, notching for wire, etc; flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc complete. complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire

Supply only chain link fencing of size 50 mm x 50mm, 4mm dia & weight not less than 4.50 Kg/ Sqm complete all as specified and directed

M & L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L for Mild steel TMT bars 5 mm to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping as in stirrups for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M&L for framed work of rolled mild steel conforming to Gde Fe 290-0 or Fe 165-0 as in doors or gates of angle or other section with gusset plates, rails, braces, etc, drilled for fixing of steel sheeting or other covering; doors etc to be prepared for hanging or sliding with and including either hooks & hinges or steel hanging door fittings (exclusive of steel sheeting, running rails & guides) and hanging, fastening & fixing complete all as specified and directed.

M & L Brick work with fly ash bricks, straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and directed

M & L Brick work with fly ash bricks, straight or curved on plan exceeding 6m mean radius, built in cement mortar 1: 4 complete all as specified and directed

M & L for brickwork with fly ash bricks, straight or curved on plan to any radius in half brick thick walls, built in 1:4 CM complete all as specified and directed

Taking down cement plaster on brick wall or stone wall etc including raking out joints hacking for key, scrubbing down with water etc complete all as specified and directed

M&L for rendering 10mm thick in CM 1:3 on ceiling surfaces of RCC or brick complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces finished even and fair complete all as specified and directed.

M&L for Rendering 10mm thick in cement mortar 1:4 on faces of brick work or concrete surfaces, finished fair and even complete. complete all as specified and directed.

M&L for preparation of newly plaster surface of ceiling and applying two coats of white wash complete all as specified and directed.

M&L for preparation of new plastered surface of wall and applying two coats of oil bound distemper over a coat of primer over & including 2 mm thick wall care putty complete all as specified and directed.

M&L for preparation of new plastered surface of wall and applying two coats of cement base paint over & including one coat of primer complete all as specified and directed.

M&L for preparation of old decorated surface of wall and applying one coat of white wash on wall complete all specified and as directed.

M&L for preparation of old decorated surface of ceiling and applying one coat of white wash on ceiling complete all specified and as directed.

M & L for Hardcore of gauge not exceeding 63 mm broken stone, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for screed bed or bedding layer of mortar 20 mm thick in cement mortar 1: 6 for laying floor finishes complete all as specified and directed.

M&L for 75 mm thick cement concrete 1:3:6 type B2 using 20 mm graded stone aggregate in plinth protection finished even and fair including necessary form work and cutting of joints using extra cement etc complete all as specified.

Dismantling of floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M & L for non skid coloured ceramic floor tiles 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.06 Sqm but n exc 0.11 Sqm, in floor etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

M & L for non skid coloured ceramic floor tiles 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.11 Sqm but n exc 0.18 Sqm, in floor etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

M & L for non skid coloured ceramic floor tiles 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.11 Sqm but n exc 0.18 Sqm as in skirting / dado etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including 10 mm thick screed bed or bedding layer in CM 1:4 complete all as specified and directed.

M&L for glazed ceramic coloured wall tiles in vertical surface 450 X 300 X 7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering in 1:4 CM complete all as specified and directed.

M&L for vitrified pavement outdoor tiles of 300mm X 300mm X 9-10 mm thick coloured for floor /pavement etc and jointed in solvent and pointed in coloured cement to match the tiles including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and as directed.

M&L for 60 mm thick M-35 grade factory made rubber moulded vibratory compacted cement concrete interlocking paver block in approved design and colour confirming to IS 15658-2006 with grey cement and pigment as approved and laid over and including 30 mm thick sand cushion and joints filling with sand complete all as specified and directed.

M & L for 18 to 20 mm thick granite (of any type) work (table rubbed and polished) including the screed bed in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations compete all as specified and as directed.

S&F factory made solid PVC door frame of size 50 mm x 95 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube with wooden grain printed PVC sheet used inserted of plain colour PVC sheet & edges will be painted to match with printed sheet complete all as specified and directed.

S&F factory Made Solid PVC Moulded Door Shutters 28 to 30 mm thick with partical board core (stile:) with 2,4 or 6 raised panel design with 2 mm thick 3D wood grain moulded PVC Sheet polyyurathene painted on the front Face & 2 mm prelam PVC sheet on back face & fixing in frame at site complete all as specified and directed.

S&F factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F of galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks of galvanised wire staples in repair complete all as specified and directed.

S&F in repair prelaminated MDF type board 18/19 mm thick, interior grade, prelaminated on one side with decorative choice lamination and other side balancing white lamination as in Cupboard Shutter / Cupboard shelves with and including external teak wood lipping 6mm thick and 18/19 mm wide fixed with nails on edges complete all as specified and directed.

S&F aluminium section powder coated of colour as approved fixed type ventilator with onr or more rebates including joining cleat for fixing etc complete all as specified and directed.

S & F framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed

M&L for preparation of new steel surfaces exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F 100 mm long stainless steel butt hinges with steel pin complete all as specified and directed.

S&F 200mm long anodised aluminium barrel tower bolt of extruded section complete all as specified and directed.

S&F 150mm long anodised aluminium handles, fabricated type complete all as specified and directed.

S&F 100mm long stainless steel handle, cast type polished bright complete all as specified and directed.

S&F 100 mm long mild steel butt hinges, cold rolled, medium weight complete all as specified and directed.

S&F 300mm long, aluminium alloy, anodised aldrop door bolt including fixing clips of sheet, cast or extruded section and fixing bolts and 16mm dia bolt of sliding bolts of extruded sections complete all as specified and directed.

S&F 3 mm thick sheet glass ordinary quality in square n.exc 0.5 Sqm in each pane for new ventilator / window shutter complete all as specified and directed.

S&F 3 mm thick figured glass pin head type in square n.exc 0.5 Sqm in each pane for new ventilator / window shutter complete all as specified and directed.

S&F 4.8 mm thick sheet glass ordinary quality in square n.exc 0.5 Sqm in each pane for new ventilator / window shutter complete all as specified and directed.

S&F 5 mm thick figured glass pin head type in square n.exc 0.5 Sqm in each pane for new ventilator / window shutter complete all as specified and directed.

S & F vitreous China white wash down water closet pan (pedestal pattern) including fixing bolts, plastic water closet white. seat cover closed pattern with flat bottom (white colour) and cover and mild steel chromium plated or aluminium hinging device complete all as specified and directed.

S&F vitreous china wash and basin, white, flat back, size 550 mm x 400 mm fixed on MS bracket including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe, waste fitting, pipe and union complete all as specified and directed.

S&F vitreous china wash and basin, white, flat back, size 550 mm x 400 mm fixed on MS bracket including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe, waste fitting, pipe & union and fixed in repair complete all as specified and directed.

S&F WC squatting pan “Orissa Pattern” of size 580 x 440mm white with integral foot rest (excluding flushing cistern & flush pipe) including connection to trap and to flush pipes etc and lime concrete bedding complete all as specified in SSR and including 'P' or 'S' trap and fixed in repair complete all as specified and directed.

S & F chromium plated bottle trap ( with internal partition 32 mm size with 300 mm x 190 mm long wall connection pipe and wall flange complete all as specified and directed.

S& F vitreous china urinal half stall type ( flat back) of size 635x395x420mm, white with grating and union for discharge pipe ( excluding flushing cistern including 32mm dia PTMT coupling and waste pipe, providing and fixing plugs, bedding urinal against wall in CM 1:2 complete all as specified and directed.

S&F rotational moulded polyethylene water storage tank of capacity 500 ltr (Cylindrical/vertical with closed top) triple layer construction, ISI marked hoisted & fixed in position complete all as specified and directed.

S&F in repair rotational moulded polyethylene water storage tank of capacity 500 ltr (Cylindrical/vertical with closed top) double layer construction, ISI marked hoisted & fixed in position including dismantling of old tank and removing from site complete all as specified and directed.

S&F 20mm bore ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed. (Minimum weight 210 gms) complete all as specified and directed.

S&F 20mm bore ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed in repair (Minimum weight 210 gms) complete all as specified and directed.

Taking up or down 15 mm bore GI steel tubing and connections on (walls, ceiling, floors, etc.) including cleaning complete all as specified and as directed.

Refixing old 15 mm bore GI steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and as directed

S&F 15 mm bore GI steel tubing "medium grade" with all fittings and fixed to wall, floor and ceiling etc complete all as specified.

Taking up or down 20 mm bore GI steel tubing and connections on (walls, ceiling, floors, etc.) including cleaning complete all as specified and as directed.

Refixing old 20 mm bore GI steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and as directed

S&F 20 mm bore GI steel tubing "medium grade" with all fittings and fixed to wall, floor and ceiling etc complete all as specified.

S&F 25 mm bore GI steel tubing "medium grade" with all fittings and laid in floor complete all as specified.

S&F 50 mm bore GI steel tubing "medium grade" with all fittings and laid in floor complete all as specified.

S & F 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed.

S & F 25 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed.

S & F 50 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed.

S&F 15 mm dia bib taps long body with wall flange fancy type brass chromium plated with screwed down, screwed for iron pipe or for brass ferrule including all accessories complete all as specified and directed.

S&F 15 mm dia bib taps, fancy type brass chromium plated with screwed down, screwed for iron pipe or for brass ferrule including all accessories and fixed in repair complete all as specified and directed.

S&F fancy type Pillar tap 15mm bore, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure with long shanks and fly nuts, screwed for iron pipe including all accessories complete all as specified and directed.

S&F fancy type Pillar tap 15mm bore, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure with long shanks and fly nuts, screwed for iron pipe including all accessories & fixed in repair complete all as specified and directed.

S&F 15mm bore CP angle stop valve or cock fancy type of screwed down for high pressure with capstan head & cover, screwed both end for iron pipes complete all as specified and directed.

S&F 15mm bore CP angle stop valve or cock fancy type of screwed down for high pressure with capstan head & cover, screwed both end for iron pipes & fixed in repair complete all as specified and directed.

S&F stainless steel pillar tap chromium plated with flange screwed for iron pipe of 15 mm dia complete all as specified and directed.

S&F 15 mm dia health faucet abs body with 8 mm dia 01 mtr long flexible tube & wall hook complete all as specified and directed.

S&F in repair 15 mm bore CP fancy stop valve (concealed type) with long shanks and cup fixed with pipes complete all as specified and directed.

S & F in repair for 90 to 125 mm size fancy type chromium plated shower rose with swivel joints, and connecting rod including fixing to steel pipe or union complete all as specified and directed.

S&F in PVC connection 600 mm long, 15 mm size with brass chromium plated nuts complete all as specified.

S & F in repairs PVC connection 450 mm long, 15 mm size with brass chromium plated nuts complete all as specified.

S & F 600 mm long tubular towel rack with lower hanger chromium plated fancy type superior quality fixed with screw complete all as specified and directed.

S&F toilet paper holder of stainless steel, fancy type fixed to wall with chromium plated brass screws complete all as specified and directed.

S&F PVC flushing cistern 10 ltr capacity valve less syphonic action type low level with and including ball valve float & handle, waste pipe & brackets complete set all as specified and directed.

S&F PVC flushing cistern 10 ltr capacity valve less syphonic action type low level with and including ball valve float & handle, waste pipe & brackets and fixed in repair complete set all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes singles socket in any length with rubber ring joints laid / fixed in trench , floor & wall complete all as specified and directed.

S&F in repair 110 mm bore PVC (SWR) pipes singles socket in any length with rubber ring joints laid / fixed in trench , floor & wall complete all as specified and directed.

S&F in repair 75 mm bore PVC (SWR) pipes singles socket in any length with rubber ring joints laid / fixed in trench , floor & wall complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bend any radius complete all as specified and directed.

S&F in repair 110 mm bore PVC (SWR) bend any radius complete all as specified and directed.

S&F in repair 75 mm bore PVC (SWR) bend any radius complete all as specified and directed.

S&F 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F in repair 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F in repair 75 mm PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F 110 mm bore PVC (SWR) floor trap plain or multi with grating including joining to waste pipe with solvent cement joint complete all as specified and directed.

S&F in repair 75 mm bore PVC (SWR) floor trap plain or multi with stainless steel grating including joining to waste pipe with solvent cement joint complete all as specified and directed.

S & F 110 mm bore PVC (SWR) vent cowl complete all as specified.

S&F 150 mm bore salt glazed stoneware drain pipe grade 'A' laid in trenches and jointed complete all as specified and directed.

M&L for concrete bed to drain pipes 150 mm bore including forming cradles; in cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate complete all as specified and as directed

Demolition of brickwork masonry built in lime or cement mortar including all quiens arches , pillars etc. but including concrete articles complete all as specified and directed.

Cutting holes into existing manhole brick wall manhole built in CM, connection new drains making good to pipes and rendering cutting out existing benching for and forming branch channel ( 1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required for 150 mm internal dia of pipe complete all as specified and directed.

M&L for 25 mm thick cement concrete 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in leveling course of floor & other similar work complete all as specified & directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc.15 cm thick, above or below ground level including floor tiles complete all as specified and directed.

Demolition of reinforced cement concrete in ground floors and pavings not exc.15 cm thick, above or below ground level complete all as specified and directed.

M & L for Reinforced cement concrete 1:2:4 using 20 mm graded stone aggregates as in kitchen shelves complete all as specified and directed. Note:- Reinforcement to be measured & paid separately under respective item.

Use & waste of formwork to soffits of suspended slabs such as kitchen shelves and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed

S & F in repairs 600 mm long tubular towel rail , brass chromium plated of 20 mm dia complete all as specified and directed.

Cutting holes in brick walls in brick walls built in cement mortar or cement lime mortar and stone walls built in lime mortar for purpose made cutting and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required in full brick wall complete all as specified and directed.

Taking down chowkat with shutter (without taking off shutters from the frame) area not exc 1.5 Sqm each and removing from site complete all as specified and directed.

Taking down chowkat with shutter (without taking off shutters from the frame) exc 1.5 Sqm but not exc 4.0 Sqm each and removing from site complete all as specified and directed.

S&F hollow MS steel double / single rebated door frame 105x60mm or any other similar works of approved shape and size including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and directed.

M&L for 30 mm thick flush shutter, solid core construction with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 2nd class hardwood factory made door, 35 mm thick, glazed and skeleton shutters, open rebated and prepared to receive glass gauze etc (with sash bars) edges of framing plain, chamfered or rounded materials and rebated sash bars any number , edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass in door etc or provided with styles and rails as specified in SSR part 1 section 8, clause 8.20 (a) complete all as specified & directed.

S&F floor door stopper overall length of cover plate 150 mm of aluminium alloy body and tongue, anodised with hard drawn steel spring complete all as specified and directed.

M&L preparation of new wooden surface exc over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparing old plastered or unplastered surfaces of wall and applying one coat of oil bound distemper complete all as specified and directed

M&L for anti-termite treatment by treating the soil along with external perimeter of building at the rate of 2.25 litres of emulsion per metre of the perimeter wall complete all as specified and directed.

M&L for anti-termite treatment by treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L for anti-termite treatment by treating the soil along with external perimeter of building at the rate of 2.25 litres of emulsion per metre of the perimeter wall complete all as specified and directed.

M&L for anti-termite treatment by treating back fill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (area of substructure in contact with backfill to be measured) complete all as specified and directed.

M&L Damp proof course 40mm thick in cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate to horizontal or vertical surfaces including necessary form work complete all as specified and directed.

M&L for applying evenly a coat of blown type bitumen at the rate of 1.50 Kg per square metre and blinding with clean dry sand @ 0.05 Cum per Sqm complete. all as specified and directed.

M&L for polythene film, 50 micron thick, laid on a coat of bitumen primer, @ 0.30 to 0.50 Kg per Sqm complete. all as specified and directed.

Dismantling of brick tiles or terracing tiles, single layer on roofs complete all as specified and directed as specified.

Complete removal of mud phuska from roof of any thickness and removing the waste material from site to a distance exceeding 250 mtr but not exceeding 500 mtr and depositing where directed including cleaning of surface complete all as specified and directed as specified

Demolition of plain cement concrete in any position including Tar felt cement mortar bedding etc complete all as specified and directed as specified

M&L for plain cement concrete 1:2:4 type B-0 12.5mm graded stone aggregate as in roof padding, roof kerbs, benching on roof slab and other similar works laid as per slop required finished even and fair complete all as specified and directed.

M&L for 10mm thick plaster in CM 1:3, mixed with liquid water proofing compound over concrete surface of roof when concrete is green complete all as specified and directed. Note : WPC to be measured and paid separately under appropriate item.

M&L for Laying of 3mm thick APP membrane of (reinforced with non-woven fabric polyester type) (weight not less than 3 kg per sqm) shall be done using butane torch maintaining 100mm side overlap and 150mm end overlap, sealing all overlaps and bonded to the surface by fusing and bonding torch on method complete all as specified and directed. Note: All water proofing work shall be done as per manufacturer instruction and under supervision of manufacturer technical representative.

Cleaning the dust,durt and any other foreign material from roof surface and applying a coat of bituminous primer @ 0.40 ltr / Sqm uniformly and primer shall be allowed to dry over night as conforming to IS 3384-1986 complete all as specified and directed.

Supply only Liquid water proofing compound (ISI marked) complete all as specified and directed.

M&L for 40mm thick brick tiles laid over and including 15 mm thick screed bed in CM 1:4 mixed with polymer based liquid water proofing additive @ 5 % by weight of cement or as per manufacturer's instruction and the joints of tiles shall be filled with CM 1:3 mixed with crude oil as per SSR-2009 (Part-I) on roof area and proper curing with water by ponding complete all as specified and directed.

Applying two coats of bitumen based aluminium painting @ 0.15 Kg / sqm on water proofing treatment with preparation of surface as on non accessible area complete all as specified and directed.

M&L for Sunken floor treatment as in following sequence:- (a) The surface of Sunken floor is to be properly cleaning the dust, dirt and any other foreign material, fungus moss etc from the surface. (b) M&L for 10mm thick plaster in CM 1:3, mixed with liquid water proofing compound over concrete surface of sunken area when concrete is green. (c) Applying a coat of bituminous primer @ 0.40 ltr / Sqm uniformly and primer shall be allowed to dry over night as conforming to IS 3384-1986. (c) M&L for APP based polymeric water proofing membrane of 3mm thick (reinforced with non-woven fabric polyester type) (weight not less than 3 kg per sqm) shall be done using butane torch maintaining 100mm i.e. overlap and 150mm end overlap, sealing all overlaps including at all junction and corners with bonded to the surface by fusing and bonding torch on method complete all as specified and directed.

M&L for plain cement concrete 1:5:10, type E2 using 40 mm graded aggregate as in sunken filling and mass concrete works complete all as specified and directed.

M&L for 32 mm bore galvanised steel tubes 'medium grade' as in sunken spout pipe complete all as specified and directed.

Cutting holes in full brick walls, built in cement mortar for inserting of sunken pipe , holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and directed.

S&F in repairs Stainless steel grating dome 100 mm dia with or without waste holes as required complete all as specified.

S&F in repair 32 mm bore low density polyethylene (LDPE) pipes of pressure rating 6 kgf/ Sqcm white in colour fixed in repairs to walls or laid in floors including all fittings such as bend, elbow, tee etc complete all as specified and directed.

S&F in repair 20 mm dia Stainless steel curtain rod of wall thickness not less than 1mm with both side decorative brackets and fixing brackets complete all as specified and specified.

S&F in repair stainless steel sinks with drainage board of 1mm thick in kitchen or laboratory with plug washers and waste pipe including bedding in cement mortar to draft wall or including fixing cantilever brackets and connecting union or waste fitting to pipe over all size 915mm x 460mm bowl size 410mm x 330 mm x 160mm complete all as specified and directed.

S&F in repair stainless steel plate rack (utensil rack) of size 900mm X 750mm X 260mm made out of stainless steel 0.63mm thick fixed with brass screw complete all as specified and directed.

S&F 30mm width of flaps continuous (piano) hinges, mild steel, bright finish or electro galvanised complete all as specified.

S&F 100 mm hasp & staple safety type of stainless steel including bolt to hinges plate and fixed with screws complete all as specified and directed.

M&L for preparation of old plaster surface of wall by scrapping tools/electric hand grinder and applying one coat of cement base paint with paint sprayer machine complete all as specified and directed.

S&F PVC waste pipe 32mm dia, 60 cm long for WHB/urinal with cup, complete all as specified.

M&L for preparation of old decorated surface of external wall scrapping machine tools /electric hand grinder with wire brush and applying one coat of apex weather proof external paint on wall or facia etc over & including a layer of 1 mm thick wall care putty complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified and directed.

M&L joint free vitrified ceramic coloured tiles of 7 to 8mm thick area of each tile exceeding 0.18 and n.exc 0.36 Sqm in floor, shelves etc, set and jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed.

M&L for Vitrified Ceramic coloured tiles 10 mm thick (square/ rectangular) polished, area of each tiles exc 0.18 and n.exc 0.36sqm , in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

Refixing wooden or aluminium door shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each in the same opening after taking down, easing and adjusting including refixing builders hardware, glass etc as required and renewal of unserviceable screws complete. Note : Cost of glass, boards , aluminium snap bead, rubber beading for aluminium door and window shutter if required new be included in the quoted rate.

Taking down carefully point wiring of any type complete for light, fan socket or power point with fittings & fixtures such as ceiling rose, electric fittings, holders, switches, sockets, regulators, wooden batten, surface conduit/casing caping/conceal etc. removing materials including accessories for taking credit and making good disturbed surface to match the existing complete all as specified & directed.

M&L for point wiring with FRLS PVC insulated unsheathed stranded copper conductor cable 1.5 Sqmm (nominal area) 1100 volts grade, along with one single run of same size and type of copper wire as continuous earth wire to common earth dolly drawn in and including non metallic PVC rigid, medium grade concealed conduit with all fixing accessories of 20mm dia, using new MS sunk terminal boxes of thickness not less 1.2mm, new 3mm thick laminated sheet cover with brass screw and cup washers with all accessories and making good to disturbed conceal surfaces complete all as specified and directed. Note:(a) Colour code of wire shall be strictly followed , Red for Phase , Black for neutral and green for earth wire (b) The unit rate quoted is deemed to be inclusive of cost of cutting chases in wall for providing concealed conduit and making good to match with existing finish/surface.

One light/fan/bell point controlled by one switch

One point for socket outlet 5 amps on independent board but not below the switch board in same vertical plane.

One point for socket outlet 5 amp same board.

One bell/ buzzer point controlled by one push button on the same board with other switches or independent

All as per srl item No. 178 above but for one 3 pin socket outlet 15 amps, independent, with cables 2.5 sqmm size on independent board 2.5 Sqmm earth wire complete all as specified and directed.

S&F switch piano, flush type 5 amps, single pole, one way 230 volt complete all as specified & directed.

S&F socket out let 2-in-1, 3 pin, 5/6 amp flush type complete all as specified & directed.

S&F angle/ lamp/ batten type holder insulated body with back plate suitable for light point complete all as specified and directed.

S&F ceiling rose surface type bakelite 65 X 50 mm three terminal complete all as specified and directed.

S&F call bell, ding dong type, AC, 230 V, single pole complete all as specified & directed.

S&F switch piano, flush type 16 amps, single pole, one way 230 volt complete all as specified & directed.

S&F socket out let 2-in-1, 3 pin, 5/6 & 15/16 amp flush type complete all as specified & directed.

S&F fan regulator, electronic type, 5 stepped, flush type , single phase 230 volt including connection complete all as specified & directed.

S&F bell push piano flush type 5 amp, SP , 230V AC complete all as specified & directed.

Supply and laying sub class 'B' bricks laid dry and flat across the length of cable for protection of cable complete all as specified and directed.

M & L for sand cushioning with Ganga Sand to underground cable (8 cm thick before laying and 15 cm thick after laying the cable complete all as specified & directed. Note:- Punned thickness shall be measured for payment.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 Sq mm 2.0 core complete all as specified & directed. Note:- Earth work, sand & Bricks shall be paid separately under respective items

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 Sq mm 3.5 core including taking down existing worn out cable complete all as specified & directed. Note:- Earth work, sand & Bricks shall be paid separately under respective items

Taking down existing old /worn out tube/CFL/bulk head/sketch light fittings of indoor type fixed on wall of any type/size with its all accessories including lamp complete all as specified & directed

S &F LED tube light fittings with decorative ultra slim linear LED light fitting fixture 20 watt with co extruded polycarbonate body environmental friendly, Energy efficient tube light complete with all associates internally prewired & including LED lamp 20 watt 01 no. and connecting up with 2 core flexible copper conductor cable with suitable size complete all as specified & directed.

S&F LED with 10 W bulk head fitting with high output with opal diffuser 230 V AC decorative type with driver holder and LED lamp including connecting with three core flexible copper conductor cable of suitable size complete all as specified.

S & F LED light fitting 10 watt mirror type with high output with opal diffuser 2 ft 230 V AC with driver holder and LED lamp including making connection with three core PVC flexible insulated, sheathed copper conductor cable complete all as specified and directed.

S&F sheet metal enclosure for MCB's 240 volt 4 way single pole and neutral with 200 amps rated busbar, double door on wall with and including suitable flat iron clamps duly grouted/ fixed flush in the wall complete all as specified and directed.

S&F MCB SPN 32 Amps 'C' series, breaking capacity 10 KA of rating & making connection complete all as specified & directed.

S&F MCB SPN 40/63 Amps 'C' series, breaking capacity 10 KA of rating & making connection complete all as specified & directed.

S&F MCB single pole, 6 to 32 amps rating, 240 volts, 'B' series, 10 KA breaking capacity & making connection complete all as specified and directed.

S&F sheet metal enclosure single pole and neutral enclosure with a two pin and earth plug and socket along with one MCB, single pole of current rating 20 amps, C series 240 volts AC complete all as specified & directed.

Taking down main switches fuse unit, MCB/Kit kat distribution board with steel enclosure along with MCB’s /Kit kat fuse of any amps/ways including wooden board or from steel board and making good disturbed surfaces complete all as specified & directed.

S&F sheet metal enclosure for MCB's 240 volt 8 way single pole and neutral with 200 amps rated bus bar, double door on wall with and including suitable flat iron clamps duly grouted/ fixed flush in the wall complete all as specified and directed.

Taking down carefully sub main wiring of any type complete with MCB DBs MCB, isolators wooden batten, surface conduit/casing conceal etc. removing materials including accessories for taking credit and making good disturbed surface to match the existing complete all as specified & directed.

M&L for concealed sub main wiring using FRLSH PVC insulated, unsheathed stranded copper conductor cable two single core of size 4.0 Sqmm of voltage rating upto and including 1100 volts drawn in and including PVC concealed conduit of dia not less than 20 mm dia with all fittings and accessories along with one run of PVC insulated unsheathed stranded copper conductor of size 4.0 Sqmm as earth continuity conductor complete all as specified & directed. Note:- (i) Two runs of single core PVC cable with one run of earth conductor and conduit shall be measured as one length. (ii) The cost for cutting, chases required shall deemed to be included in the quoted unit rate.

M&L for concealed sub main wiring using FRLSH PVC insulated, unsheathed stranded copper conductor cable two single core of size 10.0 Sqmm of voltage rating upto and including 1100 volts drawn in and including PVC concealed conduit of dia not less than 20 mm dia with all fittings and accessories along with one run of PVC insulated unsheathed stranded copper conductor of size 10.0 Sqmm as earth continuity conductor complete all as specified & directed. Note:- (i) Two runs of single core PVC cable with one run of earth conductor and conduit shall be measured as one length. (ii) The cost for cutting, chases required shall deemed to be included in the quoted unit rate.

S&F vertical /horizontal water heater storage type, electrically operated of capacity 25 litres, BEE 5 star rated ABS/ steel body and inner tank made with stainless steel duly thermal insulated with 2 KW heating element complete with and including vent pipe , fusible plug, safety valve, earth connector, PVC connections(hot and cold) and electric connection all as specified and directed. Make:- Havells (Cat Part No GHWAMGTWH025 , Veenus (Cat Part No. AUDRA) , Bajaj (Cat part No. MAJ 25GL (New) as approved by GE.

S&F 450 mm long PVC connection heavy duty with brass union of required length not exceeding 450mm long with P.T.M.T nuts complete all as specified & directed.

S&F Exhaust fan 300 mm sweep Metallic body Range complete and shutters including required length and size of copper stranded conductor for connection from ceiling rose to connector of fan with provn of making hole in wall complete with grouting of nuts, bolts and washers and all other accessories required for fixing of fan including testing complete all as specified and directed.

S&F Exhaust fan 380 mm sweep Metallic body Range complete and shutters including required length and size of copper stranded conductor for connection from ceiling rose to connector of fan with provn of making hole in wall complete with grouting of nuts, bolts and washers and all other accessories required for fixing of fan including testing complete all as specified and directed.

S&F wall mounting fan PVC body of size 400 mm sweep including taking down the old unserviceable one & depositing the same in MES yard for further disposal complete all as specified and directed.

Supply and fixing LED building security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection bracket for street light made out of 40 mm bore GI pipe medium grade not less than 1.2 mtr length bent at 120 degree to shape fixed on pole/wall with and including 50x6mm FI clamps = 02 Nos with nut bolts, washers including painting of clamps with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M &L for Earthing complete with GI earth plate electrode 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25M deep below normal ground level) with top edge of the plate not less than 1.5m below normal GL. Connected to galvanized earth lead wire 4mm dia by means of nut, bolt, check nut and washers including necessary excavation and earth work in soft/loose soil, GI protection pipe light grade 15mm bore for protecting the GI wire mesh funnel alternate layer of charcoal dust, and salt PCC pit 1:3:6 type C1 using 20mm graded stone aggregate and 50mm thick RCC 1:2:4 type BO using 20mm graded stone aggregate cover reinforced with 8 mm dia MS TMT bars 80mm C/C both ways complete all as specified and shown in Electrical plate No.3 SSR part-1 and connected to the earth point and testing complete all as specified and directed.

S&F in replacement of factory made sheet metal enclosure TPN metalica distribution board, double door type, protection class (IP-42) suitable for mounting isolator, MCB conforming to IS- 13032, IS-8623, BS-5484 with minimum 100 amp rating copper busbar, TPN 4 ways, 415 volts complete all as specified and as directed.

S & F MCB Triple pole & neutral, 100 Amps 240 volts AC 'C' Series, 10 KA breaking capacity including making connections with copper lugs, testing as required complete all as specified and directed.

S&F sheet metal enclosure for MCB's 240 volt 8 way single pole and neutral with 200 amps rated bus bar, double door on wall with and including suitable flat iron clamps duly grouted/ fixed flush in the wall complete all as specified and directed.

Schedule of Credit (MINUS) Rs. 40,323.00 B/F from Serial Page No. [Note : Details of items for schedule of credit is given on Srl Page No. ] This amount shall be automatically deducted to arrive at tendered sum

Hi-Tech Constructions

Siddhi Constructionn

Channa Brothers and Co.

KHALSA BUILDER

M/s Vaishnavi Constructions

YASH ENTERPRISES