CERTAIN REPAIRS/REPLACEMENT TO FLOORING, PLASTERING, JOINERY, SANITARY, PERIODICAL SERVICE AND OTHER MISC ITEMS AT AF STN NARAINA UNDER AOR OF GE (AF) FARIDABAD

Amount

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar incl all quoins, arches, pillars, etc complete all as specified and directed by Engineer-in-Charge.

M&L for Brickwork with subclass 'B' bricks (old size bricks), straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

All as per item No 02 above but except bricks.

M&L for brick work with sub class ‘B’ bricks (old size brick) straight or curved on plan to any radius in half bricks thick walls, built in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster of any description on concrete surfaces such as soffit of RCC slab, chajjas and brick walls, ceiling etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15 mm thick in CM 1:6 on brick Work or concrete surfaces including finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for Rendering 15mm thick in CM 1:4 on brick work or concrete surface upto G+3 story of building, finish even and smooth (w/o using extra cement) incl WPC @3% by weight of cement as per manufacturer's manual complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 10mm thick in CM 1:3 over concrete surface as on ceiling, chhajja, shelves etc to match with existing surfaces finish even and smooth w/o using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for reparing of RCC projection, chajja, roof facia, celling by scrapping, cutting, derusting and cleaning exposed reinforcement surfaces of damaged loose RCC surface and applying neat cement slurry @ 3 kg/Sqm and filling the surface with cement plaster 1:3 one or two layer as reqd or PCC 1:2:4 as directed by Engr-in-Charge with or without facia and smooth finished and smotth edges incl two coats of weather proof exterior emulsion paint finished to match with the existing surface at any height and in any situation including necessary form work complete all as specified and directed by Engineer-in-Charge. Note:- Site for application is at various locations in patches and height varies up to 12 Meter Proper stable Scaffolding is must for working for the safety of resident of bldg and worker. Cost of all types of formwork, scaffolding and welded mesh shall deemed to be included in quoted rate.

M&L for providing RCC nominal mix 1:2:4 incl necessary formwork and providing plaster in cement mortar 1:3 and two coats of weather proof exterior emulsion paint finishes over a coat of primer for RCC projected portion as in facias, fins upto a height of 50 cm facia etc incl demolition of existing and providing TMT bars if reqd complete all as specified and directed by Engineer-in-Charge. (Note length of fins, facias shall be measured irrespective of any thickness and height). Note:- Site for application is at various locations in patches and height varies up to 12 Meter Proper stable Scaffolding is must for working for the safety of resident of bldg and worker. Cost of all types of formwork, scaffolding and welded mesh shall deemed to be included in quoted rate.

Removing vegetation growth/shrubs(girth up to 30 CM), cutting in brick wall/concrete surface upto triple storey building carefully without damaging the existing soil, vent, water supply pipe and removing roots of plants completely and filling the gaps with PCC 1:2:4, Type B-0 finished with existing surface including all scaffolding ladder etc as required surface are n.exc. 0.36 Sqm each complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new plastered surface and applying two coats of oil emulsion distemper on wall over one coat of primer incl one layer of 3mm thick white wall care putty on new plasterd surfaces and obtain smooth finish using sand paper complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new plaster surface & apply two coats of cement based paint over a coat alkali primer resistance incl one layer of 3mm thick white wall care putty on new plasterd surfaces and obtain smooth finish using sand paper complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of new plastered surface and applying two coats of oil emulsion distemper on ceiling over one coat of primer incl one layer of 3mm thick white wall care putty on new plasterd surfaces and obtain smooth finish using sand paper complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new treated plastered surfaces of wall by brooming down or steel wire brushing scrubbing down smoke soot, moulds, moss and efflorescence salts and treating oil and greasy spots removing dust, dirt and all loose scales of existing treatment using sand paper and applying two coats of weather proof exterior emulsion (water based) paint of dark colours/shade on walls (shade as approved by GE) over 1 coat of water based exterior primer incl one layer of 1mm thick plaster of paris putty to prepare the surface even and smooth for exterior/interior on wall/ceiling surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old treated plastered surfaces of wall by brooming down or steel wire brushing scrubbing down smoke soot, moulds, moss and efflorescence salts and treating oil and greasy spots removing dust, dirt and all loose scales of existing treatment using sand paper and applying two coats of weather proof exterior emulsion (water based) paint of dark colours/shade on walls (shade as approved by GE) over 1 coat of water based exterior primer incl one layer of 1mm thick plaster of paris putty to prepare the surface even and smooth for exterior/interior on wall/ceiling surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for one coat of Acrylic smooth exterior emulsion paint over one coat of acrlic primer incl one layer of 3mm thick white wall care putty for exterior/interior on old scraped wall surfaces and obtain smooth finish using sand paper complete all as specified and directed by Engineer-in-Charge. Note : Colour and make as approved by Engr-in-Charge.

M&L for one coat of Acrylic smooth exterior emulsion paint over one coat of acrlic primer incl one layer of 3mm thick white wall care putty for exterior/interior on old scraped ceiling surfaces and obtain smooth finish using sand paper complete all as specified and directed by Engineer-in-Charge. Note : Colour and make as approved by Engr-in-Charge.

M&L for preparation of old surfaces by removal of existing treatment and applying two coats of oil emulsion distemper over a coat of primer on surface of walls incl one layer of 3mm thick wall care putty on old scraped surfaces and obtain smooth finish using sand paper complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old surfaces by removal of existing treatment and applying two coats of distemper oil emulsion on ceiling over one coat of primer incl one layer of 3mm thick white wall care putty on old scraped surfaces and obtain smooth finish using sand paper complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of old wall surfaces by removal of existing treatment and apply two coats of cement based paint over a coat alkali primer resistance incl one layer of 3mm thick birla white wall care putty on old scraped surfaces or new plasterd surfaces and obtain smooth finish using sand paper complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of old surfaces by removal of existing treatment and apply one coat of cement based paint over a coat alkali primer resistance incl one layer of 3mm thick white wall care putty on old scraped surfaces and obtain smooth finish using sand paper complete all as specified and directed by Engineer-in-Charge.

M & L for one coat of synthetic enamel paint on steel surface including preparation of old steel surface width or girth exc 10cm complete all as specified and directed by Engineer-in-Charge.

M & L for one coat of synthetic enamel paint on steel surface including preparation of old steel surface width or girth n. exc 10cm complete all as specified and directed by Engineer-in-Charge.

M&L for one coat of synthetic enamel paint on wooden surfaces of any description over 10cm width or girth including preparation of old surfaces complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames with shutters not exc. 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames with shutters exc 1.5 Sqm but not exc. 4 Sqm each (without taking off shutters from the frames) complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description n exc 1 sqm each complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description exc 1 sqm and n exc 2 sqm each complete all as specified and directed by Engineer-in-Charge.

M & L for framed work as in doors of angle or other section complete drilled for fixing sheeting with all fitting and fixture complete (Fe 410-W (Gde-E-250) quality A) complete all as specified and directed by Engineer-in-Charge.

S&F for factory made 30mm thick flush panelled shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides with lipping/frame to match complete all as specified and directed by Engineer-in-Charge.

S&F for factory made 2nd class H.W. glazed and skelton door shutters 35mm thick, open rebated and prepared to received glass/gauge etc (without sash bars) edges of framing plain, chamfered or rounded and mitred , beads for securing glass etc the size of member of shutter as specified in SSR part-I clause 8.23(b) and fitted to chowkahts complete all as specified and directed by Engineer-in-Charge.

S & F solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube incl taking down old frame any type complete all as specified and directed by Engineer-in-Charge.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be convered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20 mm width stuck inside with solvant cement for stiles and plain colour PVC sheet top rail, lock rail and bottom rail on either side and as gap insert of top rail and bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and raials with suitabale PVC sheet beading, and jointed together with solvant cement, fixing in the frame at side as per specification and drawing incl 3Nos- 100mm Aluminium hinges and all suitable locking arrangement for each shutter complete all as specified and directed by Engineer-in-Charge.

S&F factory made steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay complete without glazing bars, dovetailed or welded complete all as specified and directed by Engineer-in-Charge.

M&L for anodised aluminium framed work for door, window / vent (powder coated) aluminium with one or more rebated incl jointed cleat for fixing etc complete all as specified and directed by Engineer-in-Charge.

M&L for anodised aluminium powder coated door shutter , aluminium section weighting not less than 0.55kg/RM incl necessary ACP sheet incl joining with cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, handles, lock , 2 x 150mm aluminium handles, 3 x 100mm hinges aluminium, 2 x 150mm Aluminium tower bolts,1xdoor stoper with each shutter any type incl taking down complete all as specified and directed by Engineer-in-Charge.

M&L for anodised aluminium powder coated window and ventilator shutters cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, handles, lock , 2 x 150mm aluminium handles, 3 x 100mm hinges aluminium, 2 x 150mm Aluminium tower bolts complete all as specified and directed by Engineer-in-Charge.

S&F aluminium wire guard mesh of 4mm nominal dia of wire and average width of aperture 75 - 85mm and fixed with aluminium frame / staples complete all as specified and directed by Engineer-in-Charge.

M&L for 4.8 mm thick float glass ordinary quality' frosted glass and glazing with aluminum beeding and gasket to aluminum framework in square exc 0.50 sqm in each pane in repair complete all as specified and directed by Engineer-in-Charge.

S & F for 3mm thick sheet glass ordinary quality glazing with oil putty in square n exc 0.5 sqm quality or description from steel frame and complete all as specified and directed by Engineer-in-Charge.

S & F for mild steel framed work as in grill, guard bars etc with ends of bars/FI shoulders and or riveted or forged in to spikes, framed guard bar and similar works confirming to Fe 410-0 or Fe 310-0 complete all as specified and directed by Engineer-in-Charge.

S & F for stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beads complete all as specified and directed by Engineer-in-Charge.

S & F in repair for stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beads complete all as specified and directed by Engineer-in-Charge.

S & F in repair 3mm thick sheet glass, ordinary quality and with oil putty in Square n. exc 0.5 sqm in each pane incl hacking out old broken glass from metal frame incl punching or drilling out old glazing pins/spring clips and glazed with oil putty complete all as specified and directed by Engineer-in-Charge.

S&F for MS butt hinges, medium weight, cold rolled mild steel 100mm long (ISI Marked) with welded or complete all as specified and directed by Engineer-in-Charge.

S&F for aluminum anodized barrel tower bolts of extruded section 150mm long (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

S&F for aluminum handles cast type anodized 200mm long (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

S&F for 250mm long aluminium alloy, anodised, sliding door bolt of 16mm dia with hasp, staple (bolt type) and fixing clips of sheet, extruded sections and fixing bolts and sliding bolts of extruded sections complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new steel or iron surfaces of any description not otherwise described over 10 cm girth or width and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed by Engineer-in-Charge.

M&L for two coats of synthetic enamel paint over a coat of pink primer on wooden new surfaces of any description over 10cm width or girth incl preparation of new surfaces complete all as specified and directed by Engineer-in-Charge.

S&F in repair for 25 mm dia decorative/fancy type stainless steel curtain rod with brackets and knobs at both ends as per site requirement incl taking down old existing pipes with accessories complete all as specified and directed by Engineer-in-Charge. Note: the cost of brackets and knobs is deemed to be incl in the quoted rate.

Easing and Adjusting without taking down any type wooden shutters exc 1 Sqm but n exc 2 sqm each and refixing in same opening after replacement of defective portions such as wire cloth, beading, handles, hinges, locking arrangements complete all as specified & as directed by Engineer-in-Charge. Notes : Door closer, door spring, aluminium beading, preleminated gasket, aluminum beading, preleminated particle board, sheet glass shall be measured and paid separately under respective item of schedules.

S&F in repair of door closer hydraulically regulated design No 3, universal type, suitable for door shutters of 851 to 1000m in width and weifht between 61 to 80 kg etc complete all as specified and directed by Engineer-in-Charge.

S&F in repair 2nd class hard wood beading straight (any size) for glazed/gauged joinery, renewed incl mitered etc complete all as specified and directed by Engineer-in-Charge.

M&L for repairs to sliding door bolt, hinges, pintel, locking arrangment, spike, roller, roller rails etc of steel gate/Wicket gate including welding /reveting to bring the steel gate /wicket gate in service condtions etc complete all as specified and directed by Engineer-in-Charge.

S&F ventian blind for window including necessary items required for fix to wall complete all as specified and directed by Engineer-in-Charge.

S&F in repair door seals made of aluminium strip powder coated 20 mm wide and provided rubber/ cotton mat lining fixed with screws to door shutters up to 1m width opening complete all as specified and directed by Engineer-in-Charge.

S&F in repair double legged door stopper of aluminium alloy with rubber complete all as specified and directed by Engineer-in-Charge.

S&F in repair 4mm thick figured glass pane fixed in window shutter/ventilators including necessary beading/wooden beading andoil putty complete all as specified and directed by Engineer-in-Charge.

M&L for 25 mm thick PCC type B-0, 1:2:4 (using 12.5 mm graded stone aggregate) as in laying of floor/sub base finishes complete all as specified and directed by Engineer-in-Charge.

M&L for non skid ceramic coloiured tiles 7 to 8 mm thick (square/rectangular ) area of each tile exc 0.06 Sqm but not exc 0.11 Sqm as in floor of shade & designed as approved by EIC set and jointed in neat cement slurry and pointed with white cement with colour pigment to match the colour of tiles over & incl,15 mm thick rendering in bedding layer or screed bed in cement mortar (1:6) in floors incl dismantling tiles etc complete all as specified and directed by Engineer-in-Charge.

All as per item No 62 above but area of each tile exc 0.11 sqm but n.exe 0.18 sqm, in floors & dado etc

M& L for 1st quality Glazed ceramic jointless light/coloured tiles group of size 300/350mmx450/600mm, thickness not less than 6mm as in vertical surfaces such as skirting/dado etc., set and jointed in neat cement slurry and pointed with white cement and pigment to match, laid over and including 10mm thick plastering in cement mortar 1:4, incl dismantling tiles with plaster etc complete all as specified and directed by Engineer-in-Charge. Note : Shade & design as approved by EIC/GE complete all as specified.

M&L for Vitrified tiles light shade /dark shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm , in floors set and jointed in neat cement slurry and pointed with white cement with colour pigment to match the colour of tiles over & incl ,15 mm thick rendering in bedding layer or screed bed in cement mortar (1:6) in floors incl dismantling tiles with bedding layer etc complete all as specified and directed by Engineer-in-Charge. Note : Shade & design as approved by GE

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc.laid, bedded and pointed in any mortar complete all as specified and directed by Engineer-in-Charge.

M&L for Granite 18-20 mm thick (of any type ) (table runned and polished ) in floors steps, jams, pillars,window-cills,cooking plateforms and vertical surfaces bedded and jointed with grey cement slurry and pointing in white ciment (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by Engineer-in-Charge.

M&L rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed by Engineer-in-Charge.

M&L for marble 15-18 mm (green/any colour shade approved by EIC) thick over and including cement screed bed laid on 15 mm thick CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab / staircase / steps,riser incl rubbing and polishing incl rounding to edge of marble and incl dismantling complete all as specified and directed by Engineer-in-Charge.

M & L for viterous china squating pan of (Orrissa Pattern) size 580x440 mm white with 'P' or 'S' trap front or back inlet and integral foot rest (excluding flushing cisteern and flush pipe) fixed in repair including lime concrete bedding as required set complete all as specified and directed by Engineer-in-Charge.

S&F for Vitreous China wash down water closet pan (pedestal pattern) with trap, white (excluding fixing bolts, flushing cistern and flush pipe) incl connection to drain and flushing pipe complete all as specified and directed by Engineer-in-Charge.

S&F in repair of PVC flushing cistem low level white with all accessories of 10 ltrs capacity incl flushing pipe, brackets and taking down of old CI/PVC flushing cistern complete all as specified and directed by Engineer-in-Charge.

S&F in repair for 15 mm bore Twin one angle valve/ bib tap cast copper alloy chromium plated, fancy type, screwed down high pressure, screwed both ends for iron pipe or for union complete all as specified and directed by Engineer-in-Charge.

S&F in repair for Toilet paper holder,stainless steel, fixed with and including chromium plated brass screws and and wooden/plastic cleats on walls, complete all as specified and directed by Engineer-in-Charge.

S&F in repair for Health faucet brass CP with 8mm dia 1.2 mtr long flexible pipe and wall hook fixed with brass chromium plated screws, complete all as specified and directed by Engineer-in-Charge.

S&F in repair for Vitreous China wash basin, White, flat back, size 550x400 mm excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and directed by Engineer-in-Charge.

S& F in repair for 15mm swan neck pillar cock fancy type chromium plated screw with iron pipe incl all fittings complete all as specified and directed by Engineer-in-Charge.

S&F in repair CP brass centre hole mixer without pop up waste system 15mm bore for mixing hot and cold water screwed down for iron pipe for WHB, complete all as specified and directed by Engineer-in-Charge.

S&F in repair for Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms) complete all as specified and directed by Engineer-in-Charge.

S&F in repair for liquid soap container 500ml of PTMT fixed with and incl CP brass screws and wooden/plastic cleats complete all as specified and directed by Engineer-in-Charge.

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engineer-in-Charge.

S&F in repair corner glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engineer-in-Charge.

S & F in repair vitreous china urinals, half stall type (635x450mm) , complete including providing and fixing , bedding urinal against wall in cement mortar 1:2 , pointing around urinal back in cement , grating and union for discharge pipe, (Exclusive of fixing supply pipe to flushing cistern, trap & waste pipe complete all as specified and directed by Engineer-in-Charge.

S&F in repair for Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and directed by Engineer-in-Charge.

S&F in repair for 32 mm dia Waste coupling of PTMT (half or full threaded) suitable for urinal . (Minimum weight 32mm?45gms) complete all as specified and directed by Engineer-in-Charge.

S & F in repair Bib tap CP fancy type long body 15 mm bore with will crutch or buttewrfly handle screwed down screwed to iron pipe complete with all fittings complete all as specified and directed by Engineer-in-Charge.

S & F in repair Stop cock /angle CP fancy type 15 mm bore screwed down high pressure with crutch or butterfly handle & screw both end for iron pipe or for Unions complete all as specified and directed by Engineer-in-Charge.

S & F in repair Stop cock concealed long shank chromium plated fancy type 15 mm bore screwed down high pressure with crutch or butter fly handle complete all as specified and directed by Engineer-in-Charge.

S&F in repair for 15mm sink mixer with provision for swan neck on upper side, connecting legs and wall flanges, complete all as specified and directed by Engineer-in-Charge.

S&F in repair for Brass chromium plated shower rose of 200mm size square shape with arm and with or without swivel joints, complete all as specified and directed by Engineer-in-Charge.

S&F in repair for Ball valve, high pressure with PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe or fixed of size 20 mm bore, (Min Wt 20mm- 210 gms) complete all as specified and directed by Engineer-in-Charge.

S&F in repair for Ball valve, high pressure with PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe or fixed of size 15 mm bore, (Min Wt 15mm- 185 gms) complete all as specified and directed by Engineer-in-Charge.

S&F in repair for Soap dish, fixed to plugs with chromium plated brass screws complete all as specified and directed by Engineer-in-Charge.

S&F in repair for PVC connections 600mm long superior quality with PTMT nut on both side complete all as specified and directed by Engineer-in-Charge.

S&F in repair for PVC connections 450mm long superior quality with PTMT nut on both side complete all as specified and directed by Engineer-in-Charge.

S&F in repair grating round 100/125mm size of CP complete all as specified and directed by Engineer-in-Charge.

S&F stainless steel pegset of six suitable size of length etc complete all as specified and directed by Engineer-in-Charge.

Taking up or down 15 mm dia bore steel tubing and connection including cleaning for refixing or removed to store complete all as specified and directed by Engineer-in-Charge.

S&F for GI tubing 15mm bore medium grde with all GI fittings and fixed complete to wall and ceiling or laid in floors etc incl cutting chases in brick wall pinning in making good in CM 1:3 to facings where required complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connection including cleaning for refixing or removed to store, 20 mm dia bore complete all as specified and directed by Engineer-in-Charge.

S&F GI tubing 20 mm bore medium grade medium grde with all GI fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

Taking up or down steel tubing and connection including cleaning for refixing or removed to store, 25 mm dia bore complete all as specified and directed by Engineer-in-Charge.

S&F GI tubing 25 mm bore medium grade medium grde with all GI fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed by Engineer-in-Charge.

S&F for 110mm bore PVC pipes single socketed Pressure rating @4Kg/Sq cm length "medium grade " with rubber ring joint, fixed to walls with dash ture nut and bolt at every 2 mtrs length complete , incl taking up/down old pipe with all fittings complete all as specified and directed by Engineer-in-Charge.

All as per item No 105 above but laid in trench or in floor

S&F for 110mm bore PVC Gully Trap setting / jointed with solvent cement complete all as specified and directed by Engineer-in-Charge.

S&F for 110mm bore PVC bends/junction any radius complete all as specified and directed by Engineer-in-Charge.

S&F for 75 mm bore PVC pipes single socketed Pressure rating @4Kg/Sq cm length "medium grade " with rubber ring joint, fixed to walls with dash ture nut and bolt at every 2 mtrs length complete , incl taking up/down old pipe with all fittings complete all as specified and directed by Engineer-in-Charge.

All as per item No 109 above but laid in trench or in floor

S&F for 75 mm bore PVC bends/junction any radius complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) floor trap, plain with CP grating including jointing with solvent cement, 75mm diameter of outlet complete all as specified and directed by Engineer-in-Charge.

JAIPAL AND BROTHERS (BID ID -3087640)

DEV CONSTRUCTION (BID ID -3086266)

SAGAR ENTERPRISES (BID ID -3086101)

M/S Rohit Enterprises (BID ID -3086040)

ETERNITY PROJECT (BID ID -3084903)

M/S Yamin (BID ID -3075381)

M/S Ashoka Engineers and contractors (BID ID -3086678)